until release switch remains switched

I have a switch to boolean released for my quit button (i.e. go back to false after you press on). However, sometimes it is switched. This is a problem because when I try to run again the surrender button starts press down. I'm warry on the validation of the code for reasons of company I'll have to check if I can do it. However, - anyone has faced this before? I noticed if I pressed for more, he'll be back, but if I click it faster it remains stuck to the true position. I have no references to the control to reset and without inhabitants.

The mechanical action of a stop button by default is latch when released. Use it.

Tags: NI Software

Similar Questions

  • HLDAA until the switch command global

    I have two 2 "lock up to release switches" within a structure of the event. The structure is set to 500 Ms. How can I control the switches with an overall value? Is it still possible? That I should try and assemble the two VI?

    Thank you

    Philippe


  • Change "until published switch" "lock when released" type of trigger...?

    I'm still pretty new for LV and I looked around trying to find a way to change my event trigger, but with no result... maybe the wisdom of the Board of Directors can give information me.

    I have attached a VI that gives the basic idea of what I am working with two buttons and LEDS simulate the signal, I have another process.  Basically, I have two relays that are opening or closing of a valve to maintian has set value and I'm counting the number of times, it goes from the opening to the closing if I can detect '' hunt '' (i.e. - my valve reacts more quickly than expected and about to set of shooting)

    Relay loop signal is currently acting as I switches "switch Unitl out ' that sends a 'ping' event every time that the while exectutes, but I need the signal up to the counter to act as if I've changed the switches" lock when released "... y at - it a simple way to do this?  Yet once, I looked in the forums and knowledge base, with no results... any pointers in the right direction would be much appreciated!

    Thank you

    Chad

    Using LabVIEW 2009 Pro and Windows XP Pro, if that makes a difference...

    OK, got it!  Thank you very much!  Feel free to take a look and to criticize this and if someone sees an easier way to do it please let me know!

    THX,

    Chad

  • Boolean switch until released by using a structure of the event

    I use a Boolean control with mechanical action to activate the button, I want to return to the original state.

    I use it in a structure of event defined to trigger a change in value. The action to push the button generates two events in the State on one and the other for when he returned to the stop State.

    How can I control this to prevent a single event is triggered and the second event which is put on hold until is ignored, I want the button to return to the original state and not to execute the code twice.

    Thank you

    Jim

    Right, I should have told latch.  Do not forget to place the control button somewhere it will be read to reset the latch.  It does not need to be connected to anything, just read.  Sitting inside the case of the event is very good if you do not use anywhere elsewhere.

  • Need help! Interlocked switches or buttons

    Hello

    I have an application of prison access & control running at lookout 6.1. My client asked me to add 2 buttons on the screen or switches to 2 groups of exit doors in case they have an emergency situation. They want me to add a button on the client to wait to release the first group, called Group-A. This would release the first group of doors giving the prisoners to leave the cell and enter a secure area of the postern. Then, they want a second button to free the second group of Gates called Group B. This would allow the prisoners to leave the building. They don't want to group B of the second button to be able to be used or button when Group A is already on. I need to lock the switches or push buttons (I use one or the other) I don't see any way to achieve lookout? I might even just disable the switch until the switch group-one was on but disable it only works when the switch is in mode DDE. I really need to find a solution to all of this help, anyone can give me would be greatly appreciated!

    Thank you

    Rob

    Hello

    Albert and Mike thanks for your post! I played a bit with the datamember visible but I don't like the fact that the switch is not always visible to the user. I tried your example Mike, and I think it will be the best work around my problem. Thanks again guys and if I go with an ActiveX conrtrol switch I can disable I will post the information here.

    Rob

  • Bug to stop random, DIFFERENT from the power switch question

    I found a problem that I have yet to isolate the cause of the, but his is happened a few times now.  Sometimes, when my Sansa has updated its database and has not played a song at the moment, if I change the settings and then try to play a song, it starts to play, then cut completely.  It doesn't happen often, but these are the circumstances each time.  The player will not respond and will refuse to power on.  The only way to get on is to hold the power switch until the device resets, release, and then power it turned on, which of course means another data refresh.  Once this is done, my settings are all back to where they were before the last change, I can change their return, and everything works fine.  As I said, the problem don't occur often, only about 3 times since I've had (since June), but its still an obvious problem.  If someone wants to know more about it, or want me to try a few things, let me know.  I'm mainly just let Sandisk people know, then maybe we can get this in a future firmware update.

    New firmware is in the release process now, so hang on until release us the next version.  It can help about this.  Should be within 1-2 weeks.

  • Aggregation of links ESXi requires the configuration of the physical switch?

    Hello

    I have two physical servers that I'll put up with ESXi. Each server has eight physical network cards. My plan is on each server to use:
    -2 management - connected to vSwitch0
    -2 for VMotion - connected to vSwitch1
    -2 for iSCSI - connected to vSwitch2 (I'll use a SAN)
    -2 to access VM network - connected to vSwitch3

    For each pair, a cable should be connected to switch1 and the second would be plugged into switch2.

    The switches are HP A5120 which are stacked into a big switch with RFID. for example I have a 'big' switch which, if one of the two physical switches dies or is turned off, would cause the 'great' switch to lose half of its ports. In this way, all four networks are expected to continue to operate even if a switch "dies."

    All the information I found online said that ESXi can have two physical cards attached to a unique vSwitch and can then do things smart for redundancy (in which case a physical NETWORK card dies) and load balanacing.

    However, while all the guides tell me how to configure it on ESXi, I'm still not sure if I should combine the two cables on the physical switches.

    So, my questions are:

    (1) in order to get the NIC or balancing working in ESXi, redundancy do I have to combine two physical ports that will connect connect two physical ports that connect to the vSwitch?

    (2) with the consolidation of NETWORK cards, I see how to have an active adapter for the management network, and an auxiliary card works fine, but for the iSCSI network, I wouldn't have only two active adapters for double the bandwidth?

    Any ideas would be much appreciated.

    Thank you.

    (1) in order to get the NIC or balancing working in ESXi, redundancy do I have to combine two physical ports that will connect connect two physical ports that connect to the vSwitch?

    No, there is no need to configure etherchannel/LACP but this will depend on the type of load balancing, you click on the ESXi host - if you use by default, you don't need to configure Etehrchannel/LACP since traffic for each virtual network interface will be only com ove a single physical port, but you will always have the reiciliency to the case where if one of the physical NIC fails traffic then released the remaining port

    If you select the hash of the IP load balancing, you must then implement Etherchannel/LACP on your physical switch since traffice can come form any physical port in the team.

    (2) with the consolidation of NETWORK cards, I see how to have an active adapter for the management network, and an auxiliary card works fine, but for the iSCSI network, I wouldn't have only two active adapters for double the bandwidth?

    Onece well once again it will depend on the Load Balancing method, you select, but you will never be able to create links physical ports to get all of the 2 GB =

    I also moved it to a more appropriate forum-

  • ORA-00257: archiver error. Connect internal only, until that releases

    Hi all

    From the connection to my 10g database, I encounter the error ORA-00257: archiver error. Connect internal only, until released by.

    How to connect internally and to solve this problem step by step.

    Kind regards
    Stephen

    Dollongo wrote:
    Hi all

    From the connection to my 10g database, I encounter the error ORA-00257: archiver error. Connect internal only, until released by.

    How to connect internally and to solve this problem step by step.

    Kind regards
    Stephen

    Your disk space or the flash recovery area is full, delete the old archivelogs or backup them and then perform

    rman target /
    crosscheck archivelog all;
    delete expired archivelog all;
    

    or connect with sqlplus

    sqlplus "/as sysdba"
    show parameter db_recovery_file_dest_size
    alter system set db_recovery_file_dest_size=
    alter system switch logfile;
    
  • Notify the switches - the reasons why I shouldn't put it no?

    I understand when to notify the switches would be set to no (NLB and Unicast); However, how does it influence the VM environment?  I set it to no. to use NLB, but I would like to know if attributing it NOT is a negative thing.

    Are there problems that might arise in assigning notify NO switches? Could Virtual Machines disconnect if a there is a failure of the NETWORK card? Or is it rather a good to have features?

    Examples would be great.

    Thank you
    David

    Yes, assigning "Notify switch" is a bad thing.

    Here's why...  Your VMware hosts are connected to switches of the network physical (I hope at least two different those for redundancy).  These switches are MAC address, transfer of tables.  The tables to associate each MAC address to a physical switch port.  When a frame arrives, the switch will get the MAC address in the destination table and decide which physical port to send the image to.

    If a failover from NIC, converses with your virtual machines with a different physical NIC it also means a different port on the physical network switches.  If you do not notify the network switches that something has changed, they will continue to search the information old tables and send frames to the old port.  Because the virtual machine is no longer at the old port, it won't have the frames.  You lose network connectivity.

    Who can continue for a little while - anywhere from a few seconds to a minute or two, until the switches update their tables.  For more details, search for gratuitous ARP.

    If you are using NLB, you must do two things:

    1) has cancelled two physical network adapters on each host and dedicate to those of NETWORK load balancing.   Create a new vSwitch, assign the NLB NIC dedicated to this new vSwitch and make sure that your NLB servers pass only.  Notify this vSwitch using willpower alone NLB where cheating is set to no.

    (2) for large facilities, if you have several NETWORK load balancing servers, you can cancel just two or three hosts and makes a separate group.  You can disable HA in this cluster if you wish.  You can notify switches the value no and worry affect the rest of your virtual machines.

    Hope this helps!

  • X 1 7260 AC wifi card... problems remain. A real solution?

    Woah, first note: for some reason strange lenovo forums rewritten my subject in Spanish line until I switched back on it in English. Interesting.

    Anyway,.

    I knew that the Intel wifi drivers had problems according to the number of messages in early 2014 and 2013. Allegedly new drivers solves the problem.

    But I have a lenovo bought recently (December 2014) X 1 and a terrible problem of not all networks wifi connection correctly. It's really annoying and the reason why I might be forced to return the laptop [it is otherwise very nice]. I already spent several hours trying to understand the problem, but it is not a direct answer to anywhere.

    I have the latest drivers and still have the problem. I thought that the problem was supposed to be old news.

    Anyone know what is happening with the 7260 wifi driver?

    Hello

    read the messages below:
    http://forums.Lenovo.com/T5/T400-T500-and-newer-T-series/T440p-wireless-connection-not-stable/m-p/17...
    http://forums.Lenovo.com/T5/T400-T500-and-newer-T-series/T440P-WiFi-issue/m-p/1713729#M102741

    the laptop model is not serious.

  • Front Panel hangs after the beginning of the routine

    Hello

    I am writing an application that looks a bit like that fixed. The idea is to have a Setup mode after the beginning of the program, where you can enter all the data to specify a test routine. In the first loop representing the configuration mode, I have an event structure that is pretty huge, in fact, because it represents a contextual help for my program, I added. After clicking on the Start button (which is possible only when some tabs from the tab control are selected), I turn off and the Start button gray. After that puts it on, there are several automatic modes and a manual control which are selected depending on the active tab.

    In this mode, the front suddenly freezes i.e. no control will react to my entry.

    I programmed this sample program to get because of the problem. It seems that there is a problem when using local variables and the switch until released action. The problem was solved when I selected the switch when you press mode.

    I applied the same changes in VI I develop, but the problem still remains.

    Someone at - he had an idea, why?


  • GeForce GT 240 m, problem with DirectX

    My specs:
    ASUS N51Vn-A1
    Windows 7 64 bit
    Core 2 Duo t9600 2.8 GHz
    4 GB DDR2 800 MHz RAM - memtest86 + past all
    GeForce GT 240 m 1 GB DDR3 CUDA

    I can send it to ASUS, but not because of spring break I'm at school and really need my laptop.

    The problem I have is when running the games, I will get artifacts after a random time (can be anywhere between 10 seconds to 2 hours). Then, if I keep going the artifacts will get worse and worse, until the gel (it is NOT a system graphics/game freeze freeze. Music guard play and other things). I can Ctrl + Alt + Delete, then click Cancel. This will reduce, then reload the game and it works for a few seconds and freezes again. Then finally if I continue to run the game it bluescreens pointing to nvddmkm.sys.

    I checked the ram with OCCT. I ran the "GPU: MEMTEST ' and it fails the test 2-5, but switches to 1 and 6. I copied the failures in a txt If you want me to post that. In test 2, the screen goes black and Windows reports that nvddmkm has stopped working and recovered.

    Now for the weird part. I downloaded and installed VMT (another video ram test program). It has 3 options for tests, CUDA, DirectX and OpenGL. I ran the test Direct X, and it is not about all the tests. Then, when I ran in OpenGL mode it passed all tests. He passed again when I put it in CUDA mode. This makes no sense. His essay the same RAM, but fails depending on the software used. This is why I'm not sure whether material. I tried upgrading Direct X and even to reinstall Win 7. Do not know what could cause this do.

    Once again this problem ONLY occurs when you run the game using a ton of memory. Like COD4, Crysis, Mass Effect 2, Dragon Age, ect. I ran a few tests of stress several GPU and the map was stable. I've run furmark (and OpenGL program) for 2 hours. My temp peaked at 89 C. I also ran OCCT (pretty sure this stress test is OpenGL too but not sure) for 1 hour and remained stable. In my DxDiag it says also I 2777-MB total video memory, when the card has only 1 GB. This makes me think that it is sharing ram which could be the source of the problem. It would make more sense on why it is in DX anyway.

    So my question is:
    Is it possible to determine that it is in fact a hardware problem and not a software problem? Also is it possible that I can fix it temporarily until released when I can sent my laptop to fixed it? As disable a section of ram that has problems? Or a way to erase the memory of corruption. Also is there a way to prevent sharing ram Direct X?

    Thanks to all who help!

    Hello. I thought about it. It was not DirectX. I found that it is bad VRAM. I had to underclock the VRAM to make stable games. The clock speeds stock for the video card on my laptop are 550 core and 790 mem. I ran it to the kernel 520 and 700 mem. This seemed to resolve the issue. I will RMA as soon as slacking off.

  • New Apple ID Photo transfer

    I am connected to my old Apple ID on my MacBook, but have a different, new ID, apple on my iPhone. I have thousands of photos on my Mac that I'm terrified of losing if I change. Is it possible to transfer my ID apple without them all removed on my Mac. Thank you in advance. John

    Why do you think changing the AppleID will remove your photos from the Mac?

    Is the library of Photos on your Mac a photo library of iCloud?  If so, you are using "Optimize Mac Storage"?

    If you use "Optimize Mac Storage" you must disable this option and download all photos in iCloud photo library, until you switch to a different AppleID to iCloud photo library.  Your Mac has enough free storage to download all photos in iCloud?  If so, download the photos to iCloud and then disable iCloud photo library as described here: https://help.apple.com/photos/mac/1.2/?lang=en#/phtf5e48489c (the last paragraph - stop using iCloud photo library)

    Stop using iCloud photo library

    Important: If you turn off your iCloud photo library, you will be prompted to choose 'Download this Mac originals' in the iCloud Photos preferences pane, then all your original photos can be downloaded from iCloud to your Mac. Be sure to leave your originals to download before shutting iCloud library completely.

    1. Choose Photos > Preferences, then click on iCloud.
    2. Uncheck the box for iCloud photo library to turn it off.

    After having turned off iCloud photo library, the Photos on your Mac app can not access your photos or videos stored in iCloud. The changes you make to photos on your Mac do not appear on other devices, and the new photos you take will not be added to the Photos on your Mac. Your library remains in iCloud and available to other devices than iCloud use photo library.

    Once all photos are back safely on your Mac, you can change again for the new AppleID in iCloud preferences and enable iCloud photo library.

  • Avoid the button clicks duplicated in the structure of the event

    Hello

    I have an apparently easy problem that I can't solve. I enclose a VI that illustrates my problem.

    My problem is this: when an event runs, the OK button is disabled, but if the user clicked the event is pending, and when the process is finished, another will start immediately. The only reason why I turn off the button is to avoid this queuing event. The mechanical action of the button is set to the switch until release (so that the button just get after that I have let go of it).

    How can I avoid this?

    Thank you!

    First of all, your mechanical action seems wrong.  By releasing latch and then move the button in the case of the event.  Currently, you use the switch to exit which is contagious stocks on the top and to the bottom of the query.

    Second, do not check the box that says 'Lock Front Panel until the end of the matter for this event'.  Notice that it has parentheses that say "reporter treatment of the actions of the user" which means he waits until the case ends (the date at which the button was reactivated).  You are basically defeating the entire purpose of the deactivation of the control because defer you the intervention of the user until the button has been reactivated.

  • Boolean to increment a counter

    I want a VI that is increment a counter where a Boolean value is true. In other words, whenever you press a switch, the counter should increment to the next whole number and so on.

    game action of your button to switch until release, if you want yor increment is every click is increment by 1

Maybe you are looking for

  • How to activate my ipad ios 90.3 pre-installation please help me

    I need help to activate my ipad before you install ios 9.3 I have try all the way, but it didn t work

  • Updates to HDD on the Satellite 2410

    I know that I can just paste any drive that will fit in, but my question is: Can I use the CD of recovery came with my laptop to re - install windows XP on the new drive, or do I have to get a separate copy of XP? The laptop model is a Satellite 2410

  • Adapter Powerline 500 + WiFi (XWNB5201)

    HelloA few weeks ago, I bought the Powerline 500 + WiFi (model XWNB5201) and it works great!Now I need an additional adapter to receive the (cable) internet connection in another room of my house (the House is very large).So my question is: what kind

  • Frequency rate real pulse readings

    When I set up a counter to generate pulse train using 'DAQmx Create Channel (CO Pulse Freq)' and provide an arbitrary value at the entrance of the "frequency", I can read the value of the real rate? SampClk.Rate on node DAQmx Timing property returns

  • Cannot uncheck several updates in the same category.

    I would have thought by now that all changes (no doubt excellent) Windows Update for Vista, that something would have been made with respect to the Active-X for XP.