Update a reference

Similar Questions

• Update the reference in the structure of the event

  Hello

  I would really appreciate if someone can help me with the next issue:

  I have a main VI with the structure of the event in the while loop.

  There is a case of a button initiating the Subvi, which extends an engine.

  To stop the loop inside the Sub - VI I pass a strict type reference him out of the main façade of VI.

  The problem is that in the event structure is not updated to reference, i.e. on press the abort button I can't stop the engine.

  The strange thing is that, without the structure of the event (only in time loop) it works. I try to put the button on the outside another loop: it does not depend on it. Without the structure of the event - everything works.

  LabVIEW 2012 32 bit

  Thanks in advance,

  Dirs

  You have the checkbox in the case where the matter set to Lock the front until the end of the case of the event?

  Is the case of the event start quickly, or is it stuck in the Subvi?

  Have you put in custody and recommendations for using events in LabVIEW - LabVIEW 2013 help ?

• I have updated the references of the bank card and still get notifications of information with countdown, is this normal?

  I have updated the references of the bank card and still get notifications of information with countdown, is this normal?

  FAQ: What should I do if I have a subscription, but my application acts as if I had a trial?

  https://forums.Adobe.com/thread/1962238

  To contact support - for the link below click on the still need help? option in the blue box below and choose the option to chat or by phone...

  Make sure that you are logged on the Adobe site, having cookies enabled, clearing your cookie cache.  If it fails to connect, try to use another browser.

  Creative cloud support (all creative cloud customer service problems)

  http://helpx.Adobe.com/x-productkb/global/service-CCM.html ( http://adobe.ly/19llvMN )

• Create a new edition of a book with updated cross-references

  I want to create a new edition of a book that has many files component (chapters), but keep the old one intact. The files of the components have many cross references. Is it possible to easily all these cross references updated to their new location?

  Unfortunately, no, for references interfile since links are absolute and will always point to the original files until you change them.

• Numbered update cross-references blocks InDesign CS4 CS6 and

  I have a major medical journal that has a hundred references, I met with the thought that the customer can insert or change the references. I was correct and the client has now several references to go, I have updated the first in the list numbered at the end and disappeared to "update the cross-refernce" and InDesign crashes. I tried this in CS6 and CS4 but both crash.

  You could try exporting as IDML and opening the IDML and saving it under a new name.

  HTH

  Kind regards

  Peter

  _______________________

  Peter gold

  Know-how ProServices

  mccoole1 wrote:

  My Indesign has the latest updates and patches (mac of my colleague - in which the error report came from - does not work). A bit annoying that Windows is not the error report, or if it doesn't it is not after that InDesign broke down.

• have updated a reference dell dimesion 4700 xp and have no audio

  I've updated a dimension 4700 dell xp I have no audio and might miss install something. I am a newbee and the guys over at upgrades have helped me, I don't know I tried their patience, bless Bill Smithers. Daavee and XPROCKS and also Geek.And Tech a few others!

  I malaware bytes, antiviruis and avast superspy, oh and CCleaner. I use Mozilla Firefox.

  Thank you for all your help

  Sincerely,

  Gina

  Hi Gina,

  Please you can proceed as follows: -.

  • Click Start, and then click on run
  • Then, in the run box, type devmgmt.msc and press enter
  • Make a note of all the units have an exclamation against them - including system devices - and tell me what they are in your next reply
  • Also to make a note of all devices listed in the other devices section (click on the + to expand this section)
  • In addition, Please enlarge the display of the maps section (click on plus the sign +) and tell me what is stated here

  Tricky

• What is the best way to update the references to file after a move?

  I have a Photoshop Elements catalog picture with about 25 k images all pointing to a network share I call \\thehive. I moved, or sync'd if you want, all the files in the network share \\thehive on a drive of local storage for better performance, which is now located on P:\ drive. I intend to treat the P drive as my main drive that reads the catalog and use \\thehive network simply as a clone of the P drive that I intend to keep in sync with SyncToy. I have already all this configuration in place, the files are sync'd on the drive P and \\thehive, everything works as expected so far. But how to do to update the catalog so that it starts from the P drive instead of the \\thehive? A photo today points to \\thehive\2008\somepicture.jpg, and I need to point to P:\2008\somepicture.jpg.

  I'm a very advanced computer user, I could edit an XML file or do some advanced operations not supported if I had to. Would appreciate your thoughts and suggestions.

  The fastest way is to directly edit the values in the catalog.pse9db database.  The database is a database SQL Lite, so if you know (or know someone who knows) how to run SQL queries against a database, you have the chance because Adobe has done a great job of a highly normalized database schema design.

  I highly recommend this tent first on a copy of your database.  In general, the procedure goes like this:

  1. Add one of your images on the P: drive in the catalog.  This establishes a list for the P: drive and its identification in the volume_table table.
  2. Run a SQL query on the table of volume_table to see a list of all the lines.
  3. Note that the values in the column 'id' for your volume "the thehive" and one "P:".
  4. Run a SQL query on the media_table table to update the value of the id_volume column, replace all instances of the id number "the thehive' with the identification number of the reader"P: ". The SQL query will look something like this:

  Update media_table

  Set volume_id = "."

  where volume_id = "."

  I tested with PSE9.0.3 on Win7, changing the location of a CD on my E: drive on a USB on my F: drive.

  Good luck!

  Ken

• FM12-"Update of the book" causes problems of cross-reference font size.

  Version of FM: 12.0.4.445

  Windows 7 Pro.

  Here's what the references are supposed to look like:

  

  Here's what it looks like after that I run 'Update book':

  

  I can fix this by running "Update of references" for the individual file.

  Is this a problem of reference page? A bug? A wacky feature?

  Thank you!

  Louis

  What is the <$paranum>in your referencing format x - ref?

  In any case, I just tested this scenario with a document in a book and the same document as a standalone. You are right, there is a funky error when update is made from the book. The character tag is collected in the block of building <$paratext>and waterfalls on the rest of the content of the paragraph.

  Please report it as a bug via: https://bugbase.adobe.com/index.cfm

• high, medium, low level calculation reference

  Hello

  Someone know the equations for the calculation of the upper, middle, reference low voltage?    I updated the reference voltage 10%, 50% and 90%. I don't know according to what the digitizer calculates level.    For example 1, the Mid level is calculated as (IVG + Vbase) * 0.5.  Wouldn't be (IVG-Vbase) * 0.5?   The Hi and the weak reference calculations also do not add up.  I was using a signal generator to generate the signals.

  I'm using version 3.5 PXI-5224 and niScope.lib.

  Example 1

  Square 3 Mhz 3.3VPP wave
  ch0                              ch1
  VPP Vpp = 4.575151 4.704506 =
  IVG naked = 3.304177 = 3.304474
  VBase Vbase =-0.618361 =-0.003679
  VHIGH = 3.304177 VHIGH = 3.304474
  VLOW VLOW =-0.001788 =-0.003679
  VMax = 4.011691 VMax = 3.956790
  VMin VMin =-0.618361 =-0.692815
  LowRef = 0.327107 LowRef =-0.226078 VV
  MidRef = 1.650249 MidRef = 1.343056 V V
  HiRef = 2.973391 HiRef V = 2.912190 V
  RiseTime = RiseTime 7.437264 = 141.967975
  FallTime = FallTime 7.438606 = 9.800559

  Example 2

  ch0                                 ch1
  VPP Vpp = 4.580664 4.612737 =
  IVG naked = 3.295510 = 3.311956
  VBase Vbase =-0.016182 =-0.001876
  VHIGH = 3.295510 VHIGH = 3.311956
  VLOW VLOW =-0.016182 =-0.001876
  VMax = 3.971204 VMax = 3.965059
  VMin VMin =-0.615605 =-0.641533
  LowRef = 0.327863 LowRef = 0.316632 V V
  MidRef = 1.646817 MidRef = 1.647887 V V
  HiRef = 2.965772 HiRef V = 2.979142 V
  RiseTime = RiseTime 7.605729 = 7.745428
  FallTime = FallTime 7.536156 = 7.708538

  Hi all

  I think I messed the calcuation.  The reference of the tensions are are correct.  It's the (Vop + Vbase) / 2 for mid level REF. The Lo and hi are also correct.

• Update of an indicator on the VI main while executing a under VI

  Hello

  I was wondering if you could help me with the following.

  I have a VI sub that basically reads a text file and sends it to the serial port. What I would do is update a bar (indicating how much of the file has been read/sent) progress on the VI main while this VI subroutine is running. I would also like to update a text box on the main VI to display the data read in the text file.

  I need to keep so I intend to use the sub on other projects LabVIEW VI modular.

  Who is the most logical way to do this? By the way I want each control to update in reference? Or is there a better way?

  Any help would be appreciated.

  Kind regards

  Matt

  Matt

  You must create a reference to your Main.vi Progrss bar, then use a propertn node in your Subvi update of the parent control.

• How do to update and refresh the main panel image appears inside the Subvi?

  Hello world

  I have an image to display the command that is in my main draw, and I have a Subvi making some process works inside.

  But what I did inside the Subvi cannot be seen in the main panel.

  I used the image session controls than nodes input/output for Subvi.

  If I use the view control image as input for Subvi node,

  I see that the actual time appears in the Subvi Panel,

  but this isn't what I wanted.

  someone at - it wise?

  aricn wrote:

  BTW,

  inside the Subvi, I pass the transformed result the Vale to property node or the Vale (signal), even I call the metheod "refresh view", nor have the effect.

  Strange.

  For example, it is your main VI (where is placed the Image display):

  

  It's your Subvi, where poster Image is updated by reference:

  

  Now, image display updated in Main.vi Subvi:

  

  Project (LV2012) as an attachment.

  Andrey.

• Impossible to update the common Assembly of 8.1 to 8.6

  Hello

  I develop c# code to interface directly with my Renault NI.  There are some examples of excellent for .NET code with DAQmx drivers; for example, AcqOneVoltageSample.2005.

  Unfortunately, I have recently updated my DAQmx, which updated the Assembly of NationalInstruments.Common of 8.1.20.616 to 8.6.35.131.  It is not surprising, when I try to open any project example .NET, as the AcqOneVoltageSample.2005, a dialog box with the logo of National Instruments appears entitled "update project references" and asking me to check that I update the referenced version of NationalInstruments.Common from 8.1.20.616 to 8.6.35.131.  I say 'Yes' and check that the assembly is referenced in the solution has indeed been changed to 8.6.35.131.

  But now, the solution will not compile.  Specifically, the compiler (Visual Studio 2008, compilation under NET2.0) get two errors:

  (1) the type 'NationalInstruments.ISynchronizeCallbacks' is defined in an assembly that is not referenced.  You must add NationalInstruments.Common version 8.1.20.616

  (2) the type 'NationalInstruments.ISupportSynchronizationContext' is defined in an assembly that is not referenced.  You must add (same as above).

  Both errors refer to the code that instantiates the DAQmx.Task object, even if it is defined in the common version 8.6.

  I checked that new version 8.6 the common is properly referenced.  When I remove that reference and add the older version 8.1 it compiles properly.  I tried to rebuild the solution, delete the .bin and .obj directories and reconstruction, by checking the option "local copy" when you reference version 8.6... nothing works.  I don't see anything special in the assembly.cs.  I can compile using the last Assembly NationalInstruments.DAQmx 8.7.20.11, just not the new NationalInstruments.Common Assembly.

  How can I get the sample files .NET for Visual Studio 2005 to compile with the new versions of NationalInstruments.Common against the. NET2.0 library?

  Thank you

  -Jim

  Jim,

  You reinstall the DAQmx Driver after the installation of Measurement Studio? You will need to reinstall the drive and make sure that you choose to install support for Measurement Studio.

  ADri-

• FPGA VI reference number

  Hello guys,.

  I have a question/problem about the FPGA VI reference.

  My situation: I have the state machine on my system in real time, calling successively the different bitfiles. To break it down into two different bitfiles.

  In situation 1, I call a bitfile and I like to read analog values and I use I2C.

  In State 2, I call a bitfile, read the same as in State 1 and besides I do other stuff on the FPGA.

  Since I use a lot subVIs on my RT system, my FPGA references are related to type 2 different defs, so that I don't have to update the reference "FPGA VI" - indicators and orders by myself, if I use a slightly updated bitfile up-to-date version. But now, I have a problem, if I use the same Subvi 'read I2C' for bitfile 1 and 2, that it does not work, because controls of type def are different. If I linked the two bitfiles to the same type definition, I get a red dot of coercion to the Subvi of entry and read/write inside functions do not work.

  Does anyone have an idea? I don't want to copy the Subvi and exchange all indicators reference inside...

  Kind regards

  Slev1n

  Well, you can have both...

  You can perform a cast of dynamic type only if necessary (before your subVIs shared as I2C) and use the static references to the unrequited subVIs.

  You could use a typedef for the FPGA ref in your Subvi I2C (with only the common subset used in the Subvi) and use the typedef as the cast function.

• Update Windows 7 windows constantly "check updates".

  Windows Update won't step since the 'check updates'. I let it run all night and in the morning it was still there check the updates. I have Windows 7 Home Premium. The only installed updates came after I installed Windows 7 in 11/10. I used MS Security Essentials, but could not be updated also, so I uninstalled. I am updating windows, but can 't seem to achieve. Any ideas?

  Not one of these updates, you reference are in my list of installed updates. The latest updates in the list come from 14/11/10. At this point, I am trying to get the update of windows to use until I have reinstall MSE or buy another anti-virus program. I think maybe that NOD 32.

  Suggest that you try to reset the Windows Update components. Go here - How to reset the Windows Update components
  Download and Save the Fixit from this page.
  Once the download is complete, close all open programs, applications and browsers.

  Now run MicrosoftFixit50202.msi and choose the default mode.
  The Fixit times execution completed, restart unless she asks you.
  Check if the system can be updated now.

  If it can be still not updated, then run the Fixit once more and choose aggressive mode.
  When it is finished running, restart the system and check to see if it can be updated.

  If he can always refresh not, then please copy & paste the last lines 50 or so WindowsUpdate.log in your response.
  How to read the Windowsupdate.log file

  MowGreen
  Expert in Windows IT Pro - consumer safety

  * - 343-* FDNY
  NEVER FORGOTTEN

• Get a reference of Subvi w/o using Open VI reference

  Is there a way to create a reference of VI without specifying the path to the file/folder to the open VI VI Refrence?  I would have thought I could right-click on a Subvi in a diagram and Create goto-> similar to the controls and indicators reference.

  My only problem with the specification of the location is the name of the VI must be hard coded in the path.  If ever I change the name of this VI special I'll have to remember to update my string constant.

  You can use a static VI reference. I didn't check, but because it's treated as a Subvi should update the reference if you're doing a "save under...". "of the LabVIEW Subvi.