Update controls with events
I'm getting to do a settings editor window that has several groups of settings that can be edited and saved. The settings are loaded and saved on a Bay of clusters. The window uses a shift register to store all changes and then you can save at the same time when you are ready. The problem I see is that if I change a value and leave the cursor in the control, and then a new group he will not read this new value. I understand that you should put the control that you want to play in the same event, but the problem is I want to be able to read this control with several events and it makes sense to have the control outside the structure of the event. I have attached a sample vi of what I am trying to accomplish. I'm relatively new to labview and learning I'm leaving, so any help would be appreciated. Thank you
Tags: NI Software
Similar Questions
-
Update of digital control with different values with array function
Hello
I have attached my code base. I want to execute the code for 2 sets of digital control with a gap between the two values, then pass it. Something like that
ABC
Initialize the P1 = 10; P2 = 20; P3 = 30; P4 = 40
Run the code
delay = 10ms
Update of P1 = 150; P2 = 200; P3 = 350; P4 = 500
Run the code
jump to abc
I am stuck how can I update the values of P1, P2, P3, P4? I thought about using a function table but couldn't go further.
Thanks for the help,
Ana
Hello Ana,
One way you might achieve what you are looking for is using property nodes. These property nodes will allow you to change the values of the block diagram control. You can set up a structure of case inside your loop that will change control through nodes of property value after a certain number of iterations. Here is a community sample that shows how to use the nodes property to change the Boolean controls:
https://decibel.NI.com/content/docs/doc-22669
-Erik S
-
problem with tab structure control and event
Hello
My program has a tab control. In each tab, I have an event structure to control some events.
I encountered some problems. These are:
1. in each tab, I set tab as an event control, to altogether from the structure of the event as tab change (for example, the image below). My first problem is that when I change the tabs, in the arch depending on whether my program is entered in the next tab environment, happening at the event: change value to main tab! And gives bad result.
2 - I've scheduled two final tabs as below in the image. I had no routine in these two tabs. Simply, I want when I change the tab, it goes to the next case of the tab control. But when I run the program, it goes to something as busy after one or two changes tab and did not work properly.
Could someone help me please?
Thanks in advance
Baran
Rebecca wrote:
I want to have 4 tabs, each tab having 3 Boolean control.
If in each tab all Boolean control wins 1, a Subvi should be run.
I wrote this code with some time within each tab loop this case hase 3 for each Boolean control. The result is true.
But I think that if I write it with a structure of the event within each tab instead of 3 cases, the cpu load will be lower.
Is it not true?
Make a unique Structure of the event.
Add events for all controls (buttons, Boolean)
When the event is triggeredcheck for active tab control and decide what void / vi to run
It will work fine you
-
Windows Live Mail is hung «Update all calendar events»
uninstall the hotmail - Windows Live Mail calendar hangs «Update all calendar events»
Windows Live Mail is hung «Update all calendar events» I have been directed to the forum relevant but didn't find any solution. I can't delete my calendar, so the only remedy I can think of is to uninstall the entire calendar functionality but can find no way to do this. Or can I roll back to an earlier version of Windows Live Mail with no functionality of calrndar?
Hello
Given that the problem is related to hotmail, I suggest you to post the question in the forums and check them off below if it helps:
http://windowslivehelp.com/solutions.aspx?ProductID=1It will be useful.
-
Cannot install McAfee on Windows XP. Errors with "Event Viewer".
Hello, I am writing on behalf of a client.
The customer has been in touch with the people of McAfee support for four days and they are still not able to install the antivirus program due to errors with Event Viewer. The people of McAfee asked the customer to reach the MS Support since then, as they say is a Windows problem.
The event viewer contains errors in the Service Control Manager,
DCOM, NetDDE.
That's my problem, put support in for me. Some fo include errors in the event viewer:
DCOM got error "the service did not to start or control request in a timely fashion." try to start WSearch service with arguments "" to start the server:
{7D096C5F-AC08-4F1F-BEB7-5C22C517CE39}
Details Product: Windows operating system ID: 7000 Source: Service Control Manager Version: 5.2 Symbolic name: EVENT_SERVICE_START_FAILED Message: The %1 service failed to start due to the following error:
%2Explanation (SCM, Service Control Manager) could not start the service specified, probably because the service is not configured correctly.
User action Do one or all of the following conditions:
- Check the error information displayed in the message.
- Check that the service password has not expired.
- Verify that the service is in the right place.
- Check that the service is not infected with a virus.
- To view the WIN32_EXIT_CODE as SCM error when you try to start the program, at the command prompt, type
application of SC name of the service
The displayed information can help you troubleshoot the possible causes of the error.If the WIN32_EXIT_CODE is zero, SCM did not attempt to start the service because the error was detected first.
Version: 5.0 Symbolic name: EVENT_SERVICE_START_FAILED Message: The %1 service failed to start due to the following error:
2%.Explanation (SCM, Service Control Manager) could not start the service specified, probably because the service is not configured correctly.
User action Do one or all of the following conditions:
- Check the error information displayed in the message.
- Check that the service password has not expired.
- Verify that the service is in the right place.
- Check that the service is not infected with a virus.
- To view the WIN32_EXIT_CODE as SCM error when you try to start the program, at the command prompt, type
application of SC name of the service
The displayed information can help you troubleshoot the possible causes of the error.If the WIN32_EXIT_CODE is zero, SCM did not attempt to start the service because the error was detected first.
There is currently no article for this specific error Microsoft Knowledge Base or an event message. For more information on other technical support options, you can use to find answers online, see http://support.microsoft.com/default.aspx. ++++++++++++++++++
Details Product: Windows operating system ID: 206 Source: NetDDE Version: 5.0 Component: System event log Message: Listen failed: %1 Explanation The computer expected data from another computer, but not the not received. The other computer does not send, or the thread on this computer that listens to the data has encountered an error.
There is currently no article for this specific error Microsoft Knowledge Base or an event message. For more information on other technical support options, you can use to find answers online, see http://support.microsoft.com/default.aspx. -
Hi, when I click Start---> Windows Update or the control panel--> Windows Update, a window titled "Windows Update" opens with some icons on this subject, but no text! I'm guessing this is an error message, but there is no text, so I have no idea what is the error message. I tried running Microsoft Fix it 50202 but nothing has changed. I am running Windows Vista Home Edition.
Screenshot is below.
Thank you.Hello
I suggest you to install the update to Windows in clean boot state and check.How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
http://support.Microsoft.com/kb/929135Note: After a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.
-
Brother MFC-7820N update fails with error 80070490
Original title: Brother MFC-7820N failed update
Apparently, I have to use the construct in Windows 8 pilots for the Brother MFC-7820n (connected via a network). I can print fine, but cannot scan. None of the drivers of brother works for the installation of the scanner. After talking with brother, they said I should use Windows Update to get the latest drivers. I tried this several times, but the update fails with 80070490. Any ideas?
Original title: Brother MFC-7820N failed update
Apparently, I have to use the construct in Windows 8 pilots for the Brother MFC-7820n (connected via a network). I can print fine, but cannot scan. None of the drivers of brother works for the installation of the scanner. After talking with brother, they said I should use Windows Update to get the latest drivers. I tried this several times, but the update fails with 80070490. Any ideas?
According to brother Tech Support, brother does not support scanning or PC to Fax printers MFC (connected Ethernet) network. Here is a direct quote to support Brother on 24/11/12:
«Currently we have everything planned out a complete set of MFL Pro Suite software (Control Center, send/receive PC - Fax, etc.).» Scan of the MFC
on a network connection is not supported by the built-in support to
Windows 8 operating system. " -
Have no control with the mouse on my Satallite P300-123
I have a problem with my mouse on the laptop. When I use the mouse, the mouse is every time left right up down.
So I have no good control with the mouse.Can someone help me with this probem?
(Sorry for my English)
Hello
Do you use the touch pad or external mouse?
If you use an external mouse disable touchpad by using the FN + F9 key combination, especially when you use the keyboard. -
How to use the "Toshiba controls" with other players?
Heey
I have a Satellite with Toshiba controls. How can I change so I can use the buttons for other media players and not only Windows Media Player?
A dude sorry for the bad news, but I fear that it is not possible to use the Toshiba controls with another application as with WMP (CD) and WinDVD (DVD)
I think that the utility was already programmed and designed to use only these two applications. -
iTunes update fails with 'a signature not valid '.
iTunes update fails with 'a signature not valid '. What can cause this error
I suspect a corrupted download. If you have trouble downloading the correct Installer iTunes try; Uncheck the box "Keep me updated", clear the cache of your browser, change the settings of the blocker, a right-click or ctrl - click on the download button, using a different browser, or by using the direct links here.
See troubleshoot problems with iTunes for Windows updates if you have additional problems at the facility.
TT2
-
PID control with big delay in the process variable
Hello
My goal is to control the temperature via a valve and heat exchanger. I proceeded variable (temperature) measured from a hose. This temperature should be raised a few degrees with a heat exchanger. So basically I need to order a valve that allows the water to flow through the heat exchanger to raise the temperature to the desired level.
My original plan was to use a base PID regulation to operate the dispenser. However, it is about 0.5 to 1 minute of delay time in the temperature probe after I opened the valve, which increases the temperature. This leads to a situation where the PID regulation valve fully open during this period (trying to get the temperature rise). Then once the temperature begins to rise it fires quite quickly. PID begins turning the tap off almost immediately, but because of the time delay in the sensor, the temperature exceeds seriously. This led to severe oscillation and at worst unstable processes. I tried to adjust the PID control to "predict" the timer to close the valve in advance to minimize the excess, but failed.
I would appreciate if anyone has any ideas how to make this type of control with Labview PID functions. I also wonder if there is a better type of control procedure for this scenario as a PID control?
-Lars
This is a very common situation in the heating control, and generally PID can be adjusted to make it work. How do you do the tuning? If you do it by trial and errors, you have little chance to succeed. For a slow process with time delay, I like to use the method Cohen Coons, or similar open Ziegler-Nichols-loop method. The idea is that you temporarily remove or disable the PID. Set the valve in a fixed position and wait for the temperature to stabilize. Then, change the setting of the valve and record temperature at regular intervals data until the temperature is stable again to a new value. Use these data to get the initial values of PID using the equations provided by the tuning method you choose.
-
To compare the name of the control with a variable
Hi all
I want to compare the name of a control with a variable in a loop. Is there any function for it in Labview? Please let me know if it is.
Thanks in advance
-
Update for Microsoft XML Core Services 4.0 Service Pack 2 for x 64 systems (KB973688). UPDATE FAILS WITH ERROR 652, ENCOUNTERED AN UNKNOWN ERROR.
Download size: 5.4 MB
Update type: Important
Jim,
Take a look at this article and see if applies: Mike KB971187 - engineer Microsoft Support responses
Visit our Microsoft answers feedback Forum and let us know what you think. -
Windows Update fails with Error 0x80072F76 on Windows 2003 server number
I try to run windows update on my windows 2003 server. The update fails with number 0x80072F76 Errow. The Windows Firewall/Internet service Connection Sharing (ICS) is stopped and the security settings on IE is set by default. IE version is 8. The Windows Update screen is also not displayed correctly.
You talk about servers, you use WSUS?
Forum specific support by WSUS:
http://social.technet.Microsoft.com/forums/en-us/winserverwsus/threads -
Could not open the page to update windows with the error 80072efe
Could not open the page to update windows with the error 80072efe
0x80072EFE - ERROR_INTERNET_CONNECTION_ABORTED - the connection with the server has been terminated.
How to reset the Windows Update components?
http://support.Microsoft.com/kb/971058TaurArian [MVP] 2005-2010 - Update Services
Maybe you are looking for
-
Nothing to add.Three days that I want to connect on https://accounts.firefox.com/signin?service=sync & context = fx_desktop_v1 & entrypoint = menubar
-
How to remove babylon as home page?
I'm stuck with Babylon as a homepage. I used REVO to uninstall the toolbar, but something in the process must have gone wrong because the home page comes back. I cleaned up the About: config, as shown in the messages earlier (mstone, homepage and the
-
Facebook only the page is extremely low, no other site don't appear that way
I updated my computer and while on my facebook page, I clicked by mistake on my mouse somewhere in the general area of the upper right of the page. Page, all the fonts, images, etc is now very low. It is the only affected site and in Internet Explore
-
Graphics card has encountered an internal error during games
can someone help me! ??? Im not sure what caused it but a week ago, when you try to play a game that has always worked well, a note appeared saying the graphics card had "encountered an internal error" and close the program. I'm not sure why this is,
-
Cannot change the QML files in new SDK
I can't edit or even load all the QML Momentics files, get the error message; "Could not open the Editor: the editor class could not be instantiated." This usually indicates a manufacturer no. - arg missing or that the name of the editor class was mi