Update generation of over-the-air analog signals

Is there a way I can change this VI to allow real-time changes in the frequency, phase, amplitude and type of waveform to the continuous output through an acquisition of data NI 9263? For the moment, changes to these variables only happen in the output signal if the program has these variables set correctly when running.

The solution to this problem:

I found this VI, and this allows me to have the hardware buffer to be continually updated with new information of signal. The 2010 version, it works very well for me in the transmission of signals in direct update via my NI 9263 measurement system.

Tags: NI Software

Similar Questions

  • BlackBerry smartphone how to get Documents to go update NOT OVER THE AIR


    I should add to the above that you may need to register with DataViz in order to access the download area (I don't know because I signed up at the beginning of this process).

    On persistence with DataViz they sent me another link with instructions, these instructions used the installer of the application (DeskTop Manager), but the instructions included requirements to remove the DeskTop Manager D2G version (obviously is not possible to speak to the support of BB).

    Finally further discussions with BB this morning had it works.  The trick is before you try to install the note above .zip file, remove your device D2G (options/adv. options/applications select D2G, and select Remove from the menu button). Then worked the rest of the instructions above.  So the above instructions will work with Windoze or Mac, and you don't need DeskTop Manager or Pocket Mac, just a card for your phone.

  • How to install an STK applet on the SIM via OTA (over-the-air)?

    Dear all,
    What I'm trying to do is to load and install an applet by sending (live) from the same sequence of direct orders of APDUs GP wrapped in orders of the envelope.
    The direct sequence sequence is to select issuer security domain, the initialize update and external authentication before loading and installation. However, 03.48 does not specify these steps of safety management. Does this mean that load and install commands can be sent without prior authentication?

    Hello

    You could try implicit initialization of secure channel. If you have SCP02 maps with i = 44, 45, 54 or 55 (GP Card Spec 2.1.1 change M), you can use a well know challenge card Pseudo-aleatoire to open the secure channel. This means that you can precalculate the channel secured without direct access to the card.

    See you soon,.
    Shane

  • Over the Air (OTA) authentication .htaccess .htpasswd 401 error

    Hello

    I have a signed application for Blackberry build against v4.7 OS and OS v4.2.

    I've successfully installed on a site to download OTA (file .jad + individual .cod files).

    User can download and install via the web link.

    The problem is I'm trying to set up basic with .htaccess authentication so that users are required to enter a username and password defined on server in .htpasswd or equivalent. It works on the emulator with MDS and on at least one device (a Verizon Wireless Tower).

    I can't make it work on phone my client or my Verizon Wireless Storm.  It fails with "error 401: Unauthorized Access."   I have full access, to the server and all newspapers.

    My .htaccess file is:

    AuthUserFile 
    AuthGroupFile /dev/null
    AuthName 
    AuthType Basic
    
    AddType text/vnd.sun.j2me.app-descriptior jad
    AddType application/java-archive jar
    AddType application/vnd.rim.cod cod
    
    
    require valid-user
    
    

    Issues related to the:

    1 .htaccess is located in a parent directory of real .jad and .cod files.  I think it's ok.  I tried putting the .jad and .cod with no change .htaccess files.  Is this ok for .htaccess in a directory parent?

    2. is it possible to change the basis of Digest authentication?

    3. why 401 error, I checked several times passwords?

    4. is there anything else I should try in the above .htaccess file?

    Please notify.

    -Sincerely, David

    They use the Internet browser on the BlackBerry Internet Service.

    When you use the Internet browser requests can pass through a number of different servers.  This means that the request to download your JAD file, and individual files of COD could come from different servers in the pool.  But as authentication would receive only with the first request therefore a 401(k) for the following applications.  There are two ways you can work around this problem.

    1. password protect your JAD file and leave the COD files without protection.

    2 use a HTTPS connection.  This translates all connections you through the same server.

  • Media Center incorrectly determines the digital tuner on my Hauppauge 1850 as incompatible to the Canada for digital channels over-the-air via antennas

    I have a hauppauge tuner card 1850. I live in the Canada. If I've set up media center with the Canada as my position the digital tuner is not recognized as compatible in my area. If I place the library with my position defined in the United States. The digital tuner is recognized and works very well. The downside is that I can not guide ads for my actual surface when I set the location in media center in the United States.

     
     
    could help you.
     
     
    Barb
     
    MVP - Windows/entertainment and connected home
     
     
    Please mark as answer if that answers your question
     
     
     
     
  • BlackBerry smartphone over the air synchronization

    Is it possible to synchronize live (documents, contacts, etc.)?  Thank you.

    If you want to share information with other users online Blackberry unit are the best option.

    If you want to synchronize your information directly with your computers there are a lot of companies to do that, not free, but...

    An option and you can download a free trial version

    http://Nexthaus.com/products_g_blackBerry.html?gclid=CNKSpZDo6ZYCFQJvswod4k2BPQ

  • Generation of the trigger (or TTL) analog signal

    Hello world

    Well I look at the droplet, riding on the vibrating bath. In this case I have to synchronize the device with the accelerometers.

    Accelerometers are connected to the vibrating plate vibrating sinusoidal with frequency of 80 Hz. I am the acquisition of acceleration using NOR-DAQ USB 6212. A camera (Camera Link Basler, NI PCIe-1433) is used to acquire images of the vibrating plate. The frame rate of the camera is 20 Hz which controlled by external signal (TTL) or camera attributes.

    I would like to generate a trigger of data acquisition (signal HAVE) to the camera at the first minimum acceleration in the attachment. I've also attached the file vi. Could if it you please let me know if is there anyway we can generate the trigger of the analog signal.

    See you soon

    NGO

    Hello, NGO,

    Can you post the update VI?

  • How can I fix a black and white screen on the air from my iPad? I rebooted it and ran the last updated IOS 9.2 on it. It is stuck and won't return to the color. All other functions work except this.

    How can I fix a black and white screen on the air from my iPad? I rebooted it and ran the last updated IOS 9.2 on it. It is stuck and won't return to the color. All other functions work except this.

    Have you checked the settings > General > accessibility > greyscale > power off.

    If this does not work ty settings > General > accessibility > zoom > on. Triple, tap the screen with three fingers. Tap choose filter. Click None. Triple, tap the screen to get rid of the menu zoom. If you have enabled greyscale in zoom you can disable it in zoom.

  • I've recently updated to the latest version of the air and now itunes 'flashes' and I think that it corrupted an iPad?  Someone at - he seen this kind of behavior before?

    I've recently updated to the latest version of the air and now itunes 'flashes' and I think that it corrupted an iPad?  Someone at - he seen this kind of behavior before?

    When you have installed iTunes, and you download it from anywhere other than the Apple servers. There is a new version of the 12.3.2.35 installer that came out some time around 23/24, which can solve the problem for you. Download and install on your existing copy.

    TT2

  • generation of digital, analog signals read snap SMU-6358

    I have two SMU-6358 card and I want to send control signals to my camera and read the analog signals from the device with them.

    For the digital control signals, I tried to set up a system where I specify the identifiers of the pins, bring them into arrays of strings - the respective waveforms would be collected in the tables too - and I transfer them to a VI of inputs/outputs multiples that puts digital waveforms for the cards output pins.

    I developed this code here, but it doesn't seem to work. I can't understand how I can convert the string and form table wave to meet the requirements of the input/output VI or which another VI I could use to do the job. Or is there a smarter way to do it?

    Thank you

    Kriváň

    Dear Kriváň

    Please find attached the VI in LV 8.6 format. Also, I HIGHLY recommend to rearrange the front panel and which makes it neater, your code is very hard to read and not structured at all. I hope this helps!

  • Problem when the PWM signal combinning and analog signal TOGETHER!

    Hello everyone,

    first I DAQmx 6212, and I need to run the water pump small (9V - 16V) that should be driven by a PWM signal; I also have a motor (5V - 13V) for a water supply which must be controlled by an analog signal and it has built in a force feedback potentiometer, I logged onto this potentiometer correction + 5V the DAQmx and used the output voltage of the third extremety as a value to diagnose to know the position of the engine.

    My VI shows:

    1 is a normal meter production to create my PWMout signal.

    2 is an analog input, I use it as a PWMin to the LabVIEW to diagnose what is happenning in my pump water through the cycle and frequency.

    3 is an entry of the third extremety of the analog potentiometer.

    4 is an analog output that I used as power supply of the motor valve and I used an AC/DC amplifier for aplify signal the DAQmx and the motor road, between the two (3. 4.) I made a comeback with a few calculations, I had a P-controller to know the real position of the engine valve.

    My problem:

    When setting to 1. and 2. in the same VI only, I get an own PWM output with no problem.

    also with 3. and 4. in the same VI only i can control the motor valve without any problem.

    but when I put all these 4 set found in the attached VI, I have a problem as the engine valve turn continuously without stopping even if I change the position of the valve between 0 and 100%, I should mention that I see a PWM normal outside a signal on my oscilloscope, another thing to delete one of (1 or 2)  and run the engine valve VI works fine without any problems.

    so this my problem, if you can think of any solution please let me know.

    Thanks in advance for your help.

    Kind regards

    Caliente

    Here's your VI, slightly modified so the two analog inputs belong to the same task.  This if only for purposes of illustration, I him have not tested.  You will still need to do some debugging.

    While changing your VI, I noticed another potential problem with your original configuration.  You have configured the two tasks of AI for the same frequency, but read you 10000 samples of one of them and only 100 samples from the other (and throw it most of it).  Data acquisition data are buffered, and if you read as fast as you acquire, the buffer fills eventually.  If you read 10,000 samples of a channel, and the other channel acquires at the same rate, then when you read from the second channel you will get old stale data or an error full buffer.

  • read the analog signal 0-10 volts of NI6123

    I'm reading the analog signal of NI 6123. The range of the analog signal is 0 to 10 volts. This works well when the signal voltage is 0 to 5v (0 ~ 32767). But when the signal is 5 to 10 volts, the value read is always 32767. I also tried the different reading function: DAQmxReadBinaryI32, DAQmxReadBinaryU16, DAQmxReadBinaryU32. The value is identical to DAQmxReadBinaryI16. My OS is windows vista. Here's the part of my codes.

    **************************************************************************************************************************************************************************

    Create analog data tasks.

    DAQmxErrChk (DAQmxCreateTask("",&datHandler));

    DAQmxErrChk (DAQmxCreateAIVoltageChan(datHandler,"Dev1/ai0:7","",DAQmx_Val_Cfg_Default,-10,10,DAQmx_Val_Volts,NULL));)

    DAQmxErrChk (DAQmxCfgSampClkTiming(datHandler,"",RATE,DAQmx_Val_Rising,DAQmx_Val_ContSamps,RATE*MAXLAS));

    DAQmxErrChk (GetTerminalNameWithDevPrefix(datHandler,"ai/SampleClock",trigName));

    Create counter tasks.

    DAQmxErrChk (DAQmxCreateTask("",&ctrHandler));

    DAQmxErrChk (DAQmxCreateCICountEdgesChan(ctrHandler,"Dev1/ctr1","",DAQmx_Val_Rising,0,DAQmx_Val_ExtControlled));

    DAQmxErrChk (DAQmxCfgSampClkTiming(ctrHandler,trigName,RATE,DAQmx_Val_Rising,DAQmx_Val_ContSamps,RATE));

    DAQmxErrChk (DAQmxRegisterEveryNSamplesEvent (datHandler, DAQmx_Val_Acquired_Into_Buffer, SPLEEN, 0, EveryNCallback, NULL));

    DAQmxErrChk (DAQmxRegisterDoneEvent(datHandler,0,DoneCallback,));

    Start the task.

    DAQmxErrChk (DAQmxStartTask (ctrHandler));

    DAQmxErrChk (DAQmxStartTask (datHandler));

    In the call back function:

    DAQmxErrChk (DAQmxReadBinaryI16 (datHandler, SPLEEN, 3.0, DAQmx_Val_GroupByChannel, data.laser, MISS * MAXLAS, & (data.dataRead), NULL));

    DAQmxErrChk (DAQmxReadCounterU32 (ctrHandler, SPLEEN, 3.0, data.counter, SPLEEN, & (data.ctrRead), NULL));

    write data to the file.

    data.cfile.Write (data.counter, sizeof (int32) * RATE);

    data.cfile.Write (data.laser, sizeof (int16) * RATE * MAXLAS);

    **************************************************************************************************************************************************************************

    Thanks in advance

    To make sure that your device is working properly, I recommend first to test the entry in measurement and Automation Explorer (MAX) analog.  You can test your device by right clicking on it in the configuration tree and selecting test panels.  See if you acquired signal 0 - 10V as you expect.  The next step would be to try one of the sample programs that perform a task of analog input.  These examples can be found in the start menu > programs > National Instruments > NOR-DAQ > text based code supported.  Try an example that does an analog input continues and double bed (instead of binary data not adjusted).

    Your program looks good at first so I found nothing that stood out.  However, one thing to check is if your function generator (or signal source) expects a 50 ohm or high impedance.  This could cause reflections of the signal and cause the device to possibly read a voltage of half of the desired value.

  • Library meets live TV with the error: "there are currently no TV signal detected for this channel. The channel may be temporarily off the air. »

    I recently changed my TV card to an analogue of Hauppauge PVR150 at a Hauppauge DVB - S Nova S more. Media Center has worked well before.

    Media Library will recognize the new card, search and branch on 239 satellite channels, but may not display the channels giving the error message "there is currently no TV signal detected for this channel. The channel may be temporarily off the air. »

    I have installed WinTV 7 and that you can view all the channels very well in this program so obviously the map and the intensity of the signal are not the problem.

    In my quest through other forums, I heard problems re codec: mpeg2 and we tried several packs of codecs (including shark007) but with no improvement.

    My last move was to uninstall Media Center, uninstall all codec packs, uninstall the TV card and drivers, then reinstall the media library and the TV card and am still unable to view TV channels.

    Suggestions have greatly accepted.

    I've searched the Internet high and low for a solution to this problem and can lead to nothing more than what is proposed here by Divya.

    The problem seems to be fairly common and seems to be associated with codec. Most of the solutions I've come across related to the installation of media center alternatives and after several tries I finally opted for new version of Media Portal 1.1.0 beta

    Installed without a hitch and so far the interface is similar to the media library but has better customization and the ability to incorporate plug-ins.

    I did try the latest version (1.0.2) of the media portal, but said she had a few problems of stability (probably related to the W7 compatibility).

    Very happy now with Media Portal 1.1.0 Beta so will not need any other solution to this problem.

  • How can I update the AIR runtime to 3.5 on Playbook OS 2.1?

    I have improved my playbook for the latest operating system and the installed AIR runtime is only 3.1 I thought 3.5 with stage3D was available. How to change the Adobe AIR runtime?

    You can't do that. The AIR runtime is part of the operating system. The BONES of the PlayBook does not intend to be updated. AIR 3.5 will be available on BB10 10.2 +.

  • Over the years I've updated Photoshop repeatedly.  When I click on start and programs it shows P

    Over the years I've updated Photoshop repeatedly.  When I click Start, programs I have CS4, CS5 and CS6 installed is displayed.  If all three are installed, doesn't it eat lots of hard drive space?  If so, can I uninstall CS4 and CS5 and still have CS6 function properly?  Note: I use Windows 64-bit versions.  Thank you in advance for your help!

    Yes, you can uninstall versions CS4 and CS5 if you use is no longer.

    It would not affect the functionality of the CS6.

    Kind regards

    Ravi.

Maybe you are looking for