Update screen hangs at the "step 3 of 3".

Similar Questions

• Screen hangs on the Satellite A30-931 - perhaps the Bios may be damaged

  Hello

  Sometimes the screen of my laptop freezes and the only way to restart is to restart my laptop.
  However this morning, after that my screen has crashed the resumption of hibernation, I found that I couldn't start my computer.
  I was getting a blank screen which was not illuminated. DVD player responded, the fan worked and the computer was not over heating.

  Finally, after several minutes of waiting, I was able to start windows. However, when the screen went white, before Windows Welcome screen appears, it crashed. Later, I was able to load windows, but the screen froze while he was always load the settings.

  There is little time, I entered the bios and after 4 minutes and 25 seconds, lines and purple small flickering blocks appeared on the screen and I couldn't do anything. The bios clock gave midnight 01/01/2002, so I think he may have corrupted.

  I find my bios which is 1.7 - PSA33E. However it seems to be a bios of windows installer only. Would it be possible to boot from the CD drive or should it XP is running, to make it work? I don't think I can get into XP quite a long time to execute and then Flash the bios, without the screen freezing first.

  Concerning

  InfoMan

  Hello

  I don t think and I don t believe that the BIOS is damaged or malfunctions could

  You description is sounds more like a graphics card problem.
  Perhaps any other part of the motherboard could be too faulty. Who knows, we can only speculate

  You said it must wait a bit until the cell phone would be lights up once more, this looks more like an overheating problem.

  Usually there is no much to see the technician must check all components of the laptop. In the worst case the mobo must be replaced because the graphics card is fixed and cannot be removed separately.

  But before you contact the ASP test to clean the fans of s for laptop
  A jet of compressed air is a useful tool to get rid of dust and debris.

  If it does not then the ASP technician you are last resort then I wish you a good luck mate

  Good bye

• HP Pavilion p6-2069sc: computer hangs during the HP splash screen

  Hello.

  I plug an ASUS GeForce GTX STRIX 750Ti to use in my Pavilion P6 - 2069sc, but when I start the computer after installing my GPU, the screen hangs on the blue HP startup screen.

  When I try to hit the ESC key to enter the BIOS or any other keys it comes just a beep of the machine.

  It is a long beep every 20 seconds or so from the computer.

  When I use the integrated graphics card, everything works as they should.

  I already upgraded to 550W 300W POWER supply

  Because your computer has been manufacturer Sept 2011, there Legacy BIOS.  The latest vBIOS UEFI was initiated at the HP units at end of 2012.  That said, either you stay with a Legacy BIOS GPU card, or choose a dual hybrid card BIOS.  The GTX 660, or GTX 670, all of which are two high-end of the legacy card would be far superior to the GTX 750Ti.   All the current hype is looking for a lower quality card, the 750Ti, based on the more low power and some GTX offering a BIOS hybrid via Select manufacturer. The Asus could not be hybrids, as you can testify.

  http://www.hwcompare.com/17301/GeForce-GTX-660-vs-GeForce-GTX-750-TI/ 450W SS6

  http://www.hwcompare.com/17306/GeForce-GTX-750-TI-vs-GeForce-GTX-670/ 550W PSU

  http://www.GeForce.com/hardware/desktop-GPUs/GeForce-GTX-660/specifications

  Based on your existing new POWER Pack, (hopefully a quality unit), 660 GTX would be good.  In my humble OPINION, an EVGA GTX 660 is better based on your power supply of the system. Please call EVGA for re - check a Legacy BIOS.

  PS I have a EVGA GTX 660 and 670 in my BIOS Legacy of <>towers.  I tried an ASUS, but he did not have an ASUS motherboard. Strange, but ASUS check the fault has his own card. Cost me $50 return shipping cost, so Please check with any manufcacturer.

• Wait for the update not associated with the previous update

  Just something VERY disturbing happened on Windows 7 PRO.

  When I started my machine today I received the notice:

  "Waiting for update complete"

  100%

  Do not log off the coast... (Sorry was not able to copy the exact message)

  The problem is that I shut down my computer early Sep 30,2015.

  My last update was the Sep25, 2015

  and it's around 23:00 UT 30 September 2015.

  Nothing should be changing my machine without telling me he'll do

  AND it identifies...

  On my way to this page, I noticed several very suspicious activity reports,

  as [random character string] as an ID for a Windows update.

  What is going on?

  We deserve a real explanation...

  A person found a weakness in the process of "updating" windows and exploited it?

  Member of the ACM 3622339 since 1990.

  Hello

  Thank you for visiting Microsoft Community and we provide a detailed description of the issue.

  According to the description, I understand the problem installation of updates on the system.

  Certainly, I understand your concern and will try my best to help you.

  There could be a possibility that this issue would have intervened if the updates were not installed correctly on the system.

  I can really imagine the disadvantages suffered by you during the installation of Windows updates. Sometimes it is really frustrating when things do not work correctly with the machine that we are planning and wait. So, we need find the root cause of the problem and I would definitely you help solve the problems in the right direction in order to get this fixed number.

  The question arises if the Windows Update package is not configured properly, or because of incomplete installation. I would say so, you remove any external media connected to the computer and try to crash restart your computer 2 or 3 times and check if you get through this error message.

  In addition to this, I suggest you try the following methods if you are able to boot to the desktop and check if the problem persists.

  Method 1:

  I suggest you run the Windows Update Troubleshooter to check if it works. Please follow the link given below.

  Open the Windows Update troubleshooting tool

  http://Windows.Microsoft.com/en-in/Windows7/open-the-Windows-Update-Troubleshooter

  Note: The troubleshooter above checks if the network card and Windows Update services work properly.

  If the problem persists, follow method 2

  Method 2:

  I suggest you to reset manually the update of Windows components. Please follow the steps outlined in the article below and check if it works.

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows

  Now, you can try to run the Windows updates and check if the steps above to solve the problem.

  I hope this information is useful.

  Please let us know if you need more help, we will be happy to help you.

  Thank you.

  Jayant

• 10 Windows hangs on the launch of Photoshop CC2015

  while trying to open the Photoshop CC 2015 on a new asus computer it comes crashing

  graphics card: nvidia gforce gts 960

  RAM: 16 GB

  10 X 64 WINDOWS

  I have 7 PROCESSOR

  Please HELP WITH HER?

  Thanks for the update.

  Follow the steps mentioned in the post 21 by Michael digital in this thread: Re: photoshop, 'kernel security check failed'

• Debug build hangs at the splash screen after Update Beta 4

  Since the update of the fall of November, debug builds Dev Alpha hang at the splash screen.

  By release notes, on the basis of known issues:

  "AIR debugger cannot display the IP host dialog box when a debugging session is initiated. This can cause applications to hang at the splash screen and fail to launch. (240219, 242986) »

  A workaround solution is given for people running Flash Builder, where you explicitly give the Debug IP address host instead

  in relying on the auto-discovery.  I use the command line flow (don't have Flash Builder), and my debug builds that were operating out of now drop from September to the start screen. -DebugHost 169.254.0.2, I added to my blackberry-airpackager command and the debug builds always hang.  Release builds signed with my symbolic debugging normally launch, as they did before the update to the decline in November.

  For people who use Flash Builder and who know how to look under the hood and find the blackberry-airpackager command that distributes when you do a debug version: to debug this launch is built successfully

  on a Dev Alpha with the November update, can you please put the blackberry-airpackager command line which

  Flash Builder is running?

  Got a reply from them and they confirmed that the dialogue will be back. Let's make it a part of our test cases in the future.

  See you soon,.

  Dustin

• age of conquerors hangs at the loading screen

  Running windows xp sp 3, the age of the conquerors hangs at the loading screen. I tried all the suggestions in the article and had no success. Age of Mythology Gold edition also fails to load beyond the cinematics (black screen)

  Running direct x9.c

  Other games work fine, just the age of Kings / age of Conq and Age of Mythology - crazy thing is the origin of the Age of Empires loads and runs.

  Hello

  1. have you made changes on the computer recently?

  Method 1.
  It is possible that a third-party application is causing the conflict.
  You are required to perform a clean boot to find the program that is causing this conflict and then disable or remove.
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353/en-us
  Note: When you are finished troubleshooting, follow the steps as explained in the article to reset the computer to start as usual.

  Method 2.
  Also I recommend you to update the card drivers video from the manufacturer's website and check.
  Note: You can visit the website of the manufacturer of the computer to get the latest drivers for Windows XP and install it.

  I hope this helps.

• My 4th generation Apple TV installed an update and asked my password which he refused to accept time and time again. How to go beyond this screen and reset the unit?

  My 4th generation Apple TV installed an update and asked my password which he refused to accept time and time again. How to go beyond this screen and reset the unit?

  If she needs your Apple ID password and you have enabled 2-factor authentication, you might have to temporarily disable the connection to complete.

  Also, you need an internet connection to perform this step here.

  If your problem is not of the above, please describe more completely. Furthermore, to give specific messages on the screen.

• My touch screen has a problem after downloading the IOS 9.0.2. Already try apple advises the steps. But the problem still occur. Already done restart of strength. Factory setting Reset also possible. But still the same problem. Can only be used at one min

  Hello!!!

  IM Apple Fan.

  Purchased IM Ipad2, Ipad4, Iphone6

  Last month I already buy s Iphone6 +.

  Today I feel unhappy

  MY IPHONE 6 'history '.

  My touch screen has a problem after downloading the IOS 9.0.2.

  Already called and try apple advises the steps. But the problem still occur.

  Already done restart of strength. Factory setting Reset also possible. But still the same problem.

  Only can be used for a minute. After that... The problem comes in again & again & again...

  APPLE.COM

  Can U help me

  Only products of Apple of love before updating the version 9.0.2

  iOS 9.0.2 happened some time. The last iOS is iOS 9.2. If you have not updated, updated. If you restored to the factory, it must have downloaded iOS 9.2. Also, if you restore to the factory and the problem is still there, then you must make an appointment at the Genius Bar to the nearest Apple store or Apple authorized service provider or call the Apple Support to have the device examined by Apple. There seems to be something wrong with the screen.

• Update of Microsoft showing the white screen

  I have a problem with windows update, it shows a white screen with #ElementModuleHeaderText #.
  #ActionCustomInstallImportant #.
  #ActionCustomIntstallOptional #.

  and that's it nothing else, the page is empty, don't cancel anything. You have any ideas what it could be and how to fix it?  Thanks for the help.

  I have not downloaded anything in recent weeks, and I can say no updates have been installed for a few weeks.

  Hi Whizzie,

  Welcome to the Microsoft Vista answers Forum!

  You can try the steps below and check if the problem is resolved.

  Step 1: reset Windows Update components .

  To reset the Windows Update components, you can follow the link provided below.

  http://support.Microsoft.com/default.aspx/KB/971058

  If the solution provided above does not resolve the problem, you can follow step 2 to perform a clean boot.

  Step 2: clean clean boot .

  1. click on start, type msconfig in the search box and press ENTER.

  User account control permission

  If you are prompted for an administrator password or a confirmation, type the password, or click on continue.

  2. in the general tab, click Selective startup.

  3. under Selective startup, clear the check box load startup items.

  4. click on the Services tab, select the hide all Microsoft Services check box, and then click Disable all.

  5. click on OK.

  6. When you are prompted, click on restart.

  7. after the computer starts, check if the problem is resolved.

  If the problem is resolved to check what is the cause of the problem, referring to the link given below:

  http://support.Microsoft.com/kb/929135

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  Click Start, type msconfig.exe in the start search box and press ENTER.

  If you are prompted for an administrator password or for confirmation, type your password, or click on Continue.On the general tab, click the Normal startup option, and then click OK.

  When you are prompted to restart the computer, click on restart.

  Hope this information is useful.

  Thank you, and in what concerns:

  Suresh Kumar-Microsoft Support.

  Visit our http://social.answers.microsoft.com/Forums/en-US/answersfeedback/threads/ Microsoft answers feedback Forum and let us know what you think.

• Computer hangs on the installation of the Windows updates

  I was out of town for two weeks.  On my return, I turned on my laptop and downloaded Wondos 27 updates and started to install. However, when he started to install the update # 26 he hung up. It was like that for three hours. I turned off the computer and restarted. He said "starting windows" and then returned to say "Windows is installing update 26 27.» If please do not turn off the power or turn off the computer. !!! It's as if he's stuck in some kind of loop. How should I address this problem so the computer will start and not get hung up again? My computer operating system is Windows 7 Vista Premium edition.

  kbp944f

  Hi kbp944f,

  Step 1: Disconnect all external devices (printers, scanner, USB(universal serial bus) readers, etc...) Except the keyboard and mouse, then check if it makes a difference.

  Step 2: Start the computer in last good Configuration on the known (LKGC). To do this, follow the steps below:

  Access the Advanced Boot menu options by turning on your computer and pressing the F8 key continuously beforeWindows begins. Boot advanced options, select the menu LKGC

  Startup options (including safe mode)
  http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode

  Using the last good known Configuration
  http://Windows.Microsoft.com/en-us/Windows7/using-last-known-good-configuration

  Check if the computer boots to the desktop and let me know

  If the problem persists,

  Step 3: Try to startup repair

  Access the preinstalled recovery options on your computer > when the computer restarts press F8> on the screen Advanced Startup Options > optionSelect fix you computer >

  Click the first option to perform the Startup Repair

  (1) the Startup Repair:- Startup Repair is a Windows Recovery tool that can fix certain problems, such as missing or damaged system files, that might preventWindows to start properly.

  Access system recovery options. Please see the steps mentioned in the link below
  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  Let me know if it works or you need help

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• After update of December, I can't pull it up to full screen. When the taskbar is removed there is always a Board of 3/4 inch at the bottom of the screen how to fix this?

  I already changed the taskbar settings and used the taskbar fix him.

  Hello sully 7890.

  Thank you for using Microsoft Windows forum.

  You have installed the latest display drivers?

  Check in the Device Manager, if your screen needs the latest drivers.

  Try the following steps:

  Step 1:

  Display drivers
  
  You must be logged on as administrator to perform these steps.

  (1) open Device Manager by clicking the Start button, click on the Control Panel, clicking system and Maintenance, and then clicking Device Manager.

  If you are prompted for an administrator password or a confirmation, type the password or click on continue.

  (2) in the Device Manager, look for the accession of the display and then double-click the device name.

  3) then click on the driver tab, click Update driver and follow the instructions.

  See the link on how to update a driver: http://windows.microsoft.com/en-us/windows7/Update-a-driver-for-hardware-that-isn ' t-work properly

  Step 2:

  Change the screen resolution

  Screen resolution refers to the clarity of the text and images on your screen. At higher resolutions, items appear sharper. They appear also smaller, so more items adapted to the screen. At lower resolutions, fewer items adapted to the screen, but they are larger and easier to see. At very low resolutions, however, images may have serrated edges.

  1. open display settings by clicking the Start button, clicking Control Panel, on appearance and customization, personalization, and then clicking display settings.

  2. pursuant to the resolution, move the slider to the desired resolution, then click on apply.

  Change the screen resolution: http://windows.microsoft.com/en-us/windows-vista/Change-screen-resolution

  Also check the settings of your monitor horizontal/vertical display provided by the manufacturer of the system, or contact with them.

  Hope this works

  Kind regards
  Aziz Nadeem - Microsoft Support

• Windows hangs on the last blue screen and is unable to stop.

  During the shutdown process, after downloading updated successfully, the is Windows XP hangs on the last blue screen "shutdown of windows.  For now I just have to unplug it from the power supply to the stop card.  I run a maintenance program, but it does not solve this problem.

  Hi, Tinker,

  1. you receive messages or error codes?

  2 have. what maintenance program you tried running?

  Method 1:

  You can visit the computer manufacturer and try updating the chipset and video card drivers.

  How to manage devices in Windows XP

  Method 2:

  You can also check if the problem occurs in safe mode.

  To start the computer in safe mode

  A description of the options to start in Windows XP Mode

  You can also read the following article and check if it helps

  Advanced Troubleshooting for shutdown problems in Windows XP

  You can check in the event viewer to see if there are newspapers in events related to the issue.

  For more information, you can consult the following article:

  Procedure to view and manage event logs in Event Viewer in Windows XP

• Windows XP hangs at the splash screen (logo). Dim screen when hooked.

  I do have problems starting XP 2 on two different hard drives.  I'm more concerned at this time is described in the title.  I bought a new hard drive (Western Digital Caviar Blue WD3200AAKS 320) to back up the data on my old hard drive, due to the other XP startup problem and installed Windows XP Home edition, as well as my motherboard drivers, etc..  It starts very well, at first, but then started a curtain to the start screen (and the splash screen is very low in this case).  I tried to remove some additional applications provided with the motherboard, no luck.  I tried to reinstall XP several times, and who has not helped.  I tried to update my video driver, running chkdsk, running Windows Memory Diagnostic (which does no problem), cleaning the registry with Advanced System Care Pro, unplug all USB devices and network cable, etc.  He continues to hang at the splash screen (weakly).  When I try to start in safe mode, it hangs at "mup.sys.  So far, I'm able to get XP to start by repeated restart later...  I searched the web to find a solution for this and have found no definitive answer.  I just ordered another new hard drive and Windows 7.  I intend to dual boot with windows 7 the new HD and XP on the current disc (assuming that this problem can be solved!).

  My other problem is on my old sister Hitachi 160 GB IDE hard drive.  A few months, our PC stop working.  After buying a new power supply (Corsair TX650w) and determine that he was not a power supply problem, I bought a new motherboard (GA-MA785GT-UD3H), (AMD Phenom II X 2 555 3.2 Ghz) CPU, RAM (CORSAIR XMS3 DHX 4 GB (2 x 2 GB) 240 - Pin DDR3 SDRAM DDR3 1333), and some new fans (old system died due to heat issues).  Once I had it put in place and I tried to boot XP from my old drive, he just went in a "boot loop".  He gets to the XP splash screen, goes black and restarts, again and again.  I tried setting the installation of XP with XP CD 3 or 4 times, without success.  This question is not as big of a deal to me now, because I now have the new hard drive with the new number to start XP (intermittent).  My main goal with the old hard drive was to save all my data.  That is, life turns on if I can't start XP on this drive (the one with the boot loop).

  Thank you for your time!

  The BIOS update has * seems * solved the problem!  I rebooted it 4 or 5 times, but also completely off the PC and it starts today.  Did not repeat the problem so far!

  It is a great place to come to answer my own questions!  Bookmark!

• I have xp pro I have activated telephone went through all the steps said active windows computing took me to the login screen, but when I try to log in, it tells me I have activated windows

  I have xp pro I have activated telephone went through all the steps said active windows computing took me to the login screen, but when I try to connect, it tells me that I need to activate windows so I click on activate the itr tells me that windows is already activated, then takes me in the newspaper and did the same thing

  To delete the message you are already enabled, you can force the activation on reboot. If the wpa.dbl and wpa.bak are damaged, they can cause a problem.
  Restart in 'Safe Mode '.
  Rename wpa.dbl and wpa.bak files located in the the\Windows\system32 folder
  Now, the message must be deleted, and you can now re-enable. TaurArian [MVP] 2005-2010 - Update Services