Updated at El Capitan and my mac doesn't see my camera Canon (connected via USB). Need help. Cannot import images.

Similar Questions

• My MacBook froze during the installation of the update at El Capitan and now I am unable to connect to any except the screen of the guest user. There was a message of panic, and somewhere in there, he said no set of OS. I tried to start without danger, it

  My MacBook froze during the installation of the update at El Capitan and now I am unable to connect to any except the screen of the guest user. There was a message of panic, and somewhere in there, he said no set of OS. I tried to start without danger, it does not work either.

  This general situation may be similar to what is mentioned in this sequel to thread of the CSA

  and if the remedy is to use instructions; detailed and I hope they are correct...

  Re: Restart fails after installation of El Capitan help!

  Or you can try and see on the repair of the system and then if your disk utility can

  See the Macintosh HD, as a boot volume, you could restart from OS X Recovery to

  the Mac system, to see if this solves the problem. There may be more than one cause.

  You could try and boot into OS X Recovery, utilities out there, and other options are available.

  • OS X: on OS X Recovery - Apple Support

  This example uses a special partition on the hard drive of recovery which is not in the

  same disc that the Mac OS X section; However if your hard drive is missing, these other

  items may also be at risk. You must have and maintain backups of your duplicate content

  on the external storage drives closed; In addition, a Time Machine backup helps to restore.

  • Apple OS X and Time Machine tips:

  http://pondini.org/OSX/home.html

  • Tips for OS X - using HD recovery:

  http://pondini.org/OSX/RecoveryHD.html

  {Using the utility disc and other tools can be done from the boot OS X Recovery volume

  Beware of the fact these tools can also delete or reformat your content; wiping.}

  Don't know what to say; you could see visiting an Apple store with genius if

  There is an official store. Usually for best time planning you would contact them for an appointment.

  • Make an appointment at an Apple Retail Store Genius Bar
  • Find an Apple authorized service provider
  • https://locate.Apple.com/country - Apple - find places - selector of country (if outside the U.S.)

  Or if there is no official retail Apple Store with genius, the following suggestion would be to contact

  a service provider authorized Apple, an independent specialist who is qualified in the repair of Apple.

  In any case...

  Good luck & happy computing!

• I need help to connect my macbook pro to my TV high definition. I just installed the latest update for el capitan, and now all of a sudden not work there.  I use a hdmi cable that has worked for me before.  Any suggestions?

  I need help to connect my macbook pro to my TV high definition. I just installed the latest update for el capitan, and now all of a sudden not work there.  I use a hdmi cable that has worked for me before.  Any suggestions?

  OS X El Capitan: use your TV as a monitor

• I'm trying to use a printer that connects via USB and he always tells me that it is not a driver?

  Hello

  I'm trying to use a printer that connects via USB and he always tells me that it is not a driver? I don't understand what is happening and I think it's a setting that I have on my computer. Can anyone help? Ive went on the website of the printer to download the driver and the im unable too.

  Hello

  OEM for the printer manufacturer is responsible for the proper functioning of the printer
  and their drivers. Check with the manufacturer of the printer support, their online
  documentation and drivers and ask in their forums.

  Good luck, you need to update or reinstall the latest driver.

  ================================================

  The main issue is probably the drivers, but these can help:

  Add or remove a printer
  http://Windows.Microsoft.com/en-us/Windows-Vista/add-or-remove-a-printer

  Solve printer problems (Vista)
  http://Windows.Microsoft.com/en-us/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-Vista&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Solve printer problems (Vista)
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  Solve printer problems (Windows 7)
  http://Windows.Microsoft.com/en-us/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Open the printer (Windows 7) Troubleshooter
  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  Find the manufacturer's Web site
  http://Windows.Microsoft.com/en-us/Windows-Vista/find-a-printer-manufacturers-website

  Find and install printer drivers in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/find-and-install-printer-drivers

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Can range of printers HP 6830 - I connect via USB and ethernet?

  I just bought a printer HP 6830.  I have a Windows Vista computer that I don't want to be connected to the internet and a PC of Windows 8.1, but also a laptop Windows 2000 who are both connected to the internet via ethernet (and can also be connected via a wireless connection).  I was hoping to connect the printer to the PC via the port USB Vista and for Windows 8.1 PC and laptop computer via an ethernet cable.  Can I connect via usb or ethernet connection at the same time?

  Hello

  You can install the software via a USB port on your Windows Vista PC, do not connect USB until the installation guide to make.

  So you can connect the printer to your network and install it on Windows 8.1 PC, USB and a network connection can be used for concurrency and would not interfere between them...

  For the PC under Windows 2000, the printer is not compatible with the operating system and there is no drivers for such a, you can find the system requirements below:

  http://support.HP.com/us-en/document/c04268294

  Kind regards

  Shlomi

• My hp s3321PC Virginia-PC on safe mode and has been hacked, I don't have the recovery CD, I need help to restore at least it ' s factory settings. Thanx

  My hp s3321PC Virginia-PC on safe mode and has been hacked, I don't have the recovery CD, I need help to restore at least it ' s factory settings. Thanx

  See the manufacturer's web page for detailed instructions on 'Factory Restore'.

• I've updated to El Capitan and Safari does not work

  Hello, I have a 13 inch Macbook Pro, bought in early 2012. I've never updated before until today when I updated to El Capitan. Now, Safari does not. Just, it isn't really access all Web sites (it does from time to time but stall and take forever to load it all) and says that Safari does not and so I have to force quit. I tried to remove all of the plug-ins and extensions, but that didn't fix it. I also just installed the update and that it did not set or the other. I don't know what to do. Chrome works very well. I'm reluctant to delete my browsing history, because there are things in there I need. Who will fix the problem? I just wanted to see if there was an alternative first. Thanks in advance.

  Please read this message before doing anything.

  This procedure is a test, not a solution. Don't be disappointed when you find that nothing has changed after you complete it.

  Step 1

  The goal of this step is to determine if the problem is localized to your user account.

  Select the feedback connections* and log in as a guest. Do not use the Safari connection only 'user comments' created by 'find my Mac '.

  While signed in as a guest, you will have access to your documents or settings. Applications will behave as if you use them for the first time. Do not be alarmed by this behavior; It's normal. If you need any password or other personal information in order to complete the test, save, print, or write them before you start.

  Test while signed in as a guest. Same problem?

  After testing, log on to the guest account and in your own account, disable it if you wish. The files that you created in the guest account will be automatically deleted when you log out of it.

  * Note: If you have enabled 'find my Mac' or FileVault, then you cannot activate the guest account. The login 'User comments' created by 'Find my Mac' is not the same. Create a new account to test and delete it, including his home folder, after testing.

  Step 2

  The goal of this step is to determine if the problem is caused by changes in the system of third party that load automatically at startup or logon, by a device, by a police conflict or corruption of system files or some system caches.

  Please take this step regardless of the results of step 1.

  Disconnect all devices wired except those required to test and remove all the expansion cards from secondary market, as appropriate. Start in safe mode and log on to the account of the problem.

  Note: If FileVault is enabled in OS X 10.9 or an earlier version, or if a firmware password is defined, or if the boot volume is a software RAID, you can not do this. Ask for additional instructions.

  Safe mode is much slower to boot and run as normal, with limited graphics performance, and some things work at all, including an audio output and a Wi - Fi connection on some models. The next normal boot can also be a bit slow.

  The login screen is displayed even if you normally connect automatically. You need your password to log on. If you have forgotten the password, you will have to reset it before you begin.

  Test in safe mode. Same problem?

  After testing, restart as usual (not in safe mode) and make sure you always have the problem. View the results of steps 1 and 2.

• updated at el capitan and I lost the bluetooth connectivity

  OS 10.5.11 El Capitan

  iMac

  Since the update to El Capitan, I can connect is no longer on my speaker Bluetooth (Logitech UEBoom) or my Naim MUSO radio.

  http://osxdaily.com/2015/12/15/reset-Bluetooth-hardware-module-Mac-OSX/

• I've updated to el capitan and want to go back because my rogue does not work

  I stupidly updated t0 el capitan of lion but now find my epson stylus sx535wd is not compatible, that I have a few important to analyze things and I'm now stuck how I go back to my old iOS please can yu help me?

  Restore your backup

• Updated at El Capitan and Final Cut Pro does not load.

  I've updated to El Capitan 10.11.3 and my Final Cut Pro 10.0.8 could not load. So I got the new Final Cut Pro X 10.2, but I can't open my old projects in the new my permeable version 10.2. How can I open my older projects in the FCP again? Thank you!

  You need to update your project and events. Start here for more information about version 10.1 when the structure of the application has changed.

  http://www.fcpxbook.com/updates/101/101libraries.html

• Updated for Sierra and cannot import images

  I upgraded to Sierra and my camera, a Canon EOS 20 d is is properly recognized.

  Prior to the upgrade:

  When I plugged the camera would open automatically. I close and open Photoshop. PS I would like to select Import-> device and my camera would be identified. When I select the camer displayed thumbnails of photo.

  After the upgrade:

  When I connect the camera pictures only opens automaticall. If I open the pictures is not a camera attached.

  PS when I select Import-> my camera device is represented, but the icon is an external drive. When I select the icon nothing is displayed.

  Hello ChuckSto,

  Thank you for using communities Support from Apple. I know have a problem with your Mac and your camera is not what you expect. The good news is that the next steps will be useful for your problem of your camera is not recognized:

  If nothing happens when you connect your digital camera

  Try the following:

  • Make sure that the USB cable is properly connected to your camera and computer. If your computer has a USB port, try connecting the cable inside.

  • Check your camera to make sure he turned on and set to mode suitable for importing the photos. See the instructions that came with your camera.

  • Check the memory card of your camera for damage. See the documentation that came with your camera for more information on this page or other potential problems.

  Photos for Mac: import pictures from a camera or a mobile device

  See you soon!

• Lightroom opens not sometimes, and when it does, cannot import images

  I have Lightroom CC.  I am extremely frustrated.  I had it on my old laptop, and everything was pretty good.  I have a new computer.  I loaded Lightroom on it.  I can't import my card images CF.  It does not recognize my external drive where I keep my Lightroom folder.  It recognizes the card (sometimes) like Lexar, instead of the previous Canon.  Sometimes the set preview to the point sometimes images not.  I was advised (and I probably should not have done this) to restore the original preferences.  Yes, I did.  Still nothing.  I thought that maybe I didn't have enough space on my external hard drive.  I imported AN image, and he did it very well.  Then, I could not go back to the library.  I'm SO tired of seeing that stupid small circle and waiting, hoping that he'll do something. I have a wedding to shoot in a few weeks and am terrified that I won't be able to download one of my photos.  I'm ready to tear my hair as before the update of Windows (not sure who had nothing to do with anything, maybe a coincidence), everything seemed to work (on my old computer) very well.  Had not really begun to do anything on my new up to our days, when the old one was.  I'm so confused at this minute I don't know what to do or who to ask.  FOR INFO.  I have a Canon 5 d and 5 d Mark IV.  I know that, for some time, the Mark IV would not import into Lightroom.  I had no problems with the 5 d, but now I am.  I import to an external hard drive to a CF card reader, traditionally.  Now, NOTHING works properly, and I am not technically savvy enough to understand or understand have the solutions I've read online.  I'm afraid to try the download of Mark IV, too.  I need HELP!

  First of all, make sure you are updated to 2015.7, which is required for the 5 d Mark IV.

  Go to help > about Adobe Photoshop Lightroom to see what version you have.

  If it's something less than 2015.7, you need to update.

  First of all, try help > updates. If this does not work, download the update 2015.7 here:

  Update of Lightroom

  After a successful 2015.7 update, you should be able to import from your camera.

• My USB 3.0 internal card reader SD and bus have both work to quit at the same time. Need help in restoring

  On my Macbook Pro 13 inch Core I5 2 .6GHz, I just noticed that my SD card reader and USB ports have stopped working. Buses from USB 3.0 and player appear in the information of the reporting system. I tried to reset PRAM and SMC but no luck so far and my Time Machine backup is on a SSD in a USB 3.0 hard drive enclosure. Any ideas how to reset the USB 3.0 Bus and drive? I'm including all system information in case it is useful

  System information:

  Model name: MacBook Pro

  Model identifier: MacBookPro11, 1

  Processor name: Intel Core i5

  Processor speed: 2.6 GHz

  Number of processors: 1

  Total number of cores: 2

  (By heart) L2 Cache: 256 KB

  L3 Cache: 3 MB

  Memory: 8 GB

  Boot ROM Version: MBP111.0138.B17

  : 2.16f68 SCM Version (system)

  USB:

  USB 3.0 Bus:

  Host Controller Driver: AppleUSBXHCILPT

  PCI Device ID:0x9c31

  PCI revision ID:0 x 0004

  The seller ID:0 x 8086 PCI

  Host controller USB Bluetooth:

  Product ID:0 x 8289

  ID:0x05ac of the seller (Apple Inc.)

  Version: 1.18

  Speed: up to 12 Mb/s

  Manufacturer: Apple Inc..

  Location ID:0 x 14330000 / 6

  Available current (mA): 1000

  Current (mA): 0

  Additional operating current (mA): 0

  Built-In: Yes

  Software:

  Presentation of the system software:

  System Version: OS X 10.11.5 (15F34)

  Kernel version: Darwin 15.5.0

  Volume: Macintosh HD to startup

  Boot Mode: Normal

  MacBook Pro name: Stuart computer

  User name: Stuart Berwick

  Ensure the virtual memory: enabled

  Integrity of system protection: enabled

  Since the starting time: 6 minutes

  USB 3.0 Bus:

  
  

  OS X Yosemite: If a USB device does not work

• cannot import images into lightroom cc using Mac

  everything I try to import images of the map, I get a message that says lightroom could not read image. The card reader works because I can import pictures from another app like iPhoto.

  The most common problem for errors "failed to read", it's that your destination folder has WRITE permissions added.

  In your LR import dialog box, verify that the destination folder is where you want it to be and correctly spelt.

  Then, using the Finder, go to this folder and make sure that your username has both READ and WRITE access to this folder and its parent.

• need help for import and synchronization

  I need assistance with importing files in lightroom.  I don't like the way that LR seems to import my images and I must be something wrong or does not switch to something or other.

  Let's say I have a main folder called example 20091208 birds.  It has 45 pictures in.  Then I have a subfolder that I created when you export 2 images I've made a few changes for.  It would be called conversions.  The record with 45 images inside are RAW images.  The two images of the subfolder are PSD files.

  When I import the main folder so that the subfolder, LR includes 2 images of the subfolder in the main folder too to increase the number in this case by two to show 47.  According to me, he did it wrong or by mistake and import should show the main folder with 45 images and the subfolder with the 2 images that I exported.  What happens here?  Thanks for your help!  It is much appreciated.

  Look at the topic library > Photos include subfolders. You can pass if necessary power on and off.

  John