upgrade ACS 5.3 5.4 fails

Hello

I try ACS 5.3.0.40 update to the new version 5.4.0.46. Everything looks ok:

ACS-machine / acsadmin # application upgrade ACS_5.4.0.46.tar.gz rep01

You want to save the current configuration? (yes/no) [Yes]?

Building configuration...

Save the configuration running at startup

Application of % CARS installation required post installation reboot...

Broadcast from root (pts/0) message (Thu Dec 6 23:36:41 2012):

The system is down for reboot NOW!

Successful application update

But the ACS (vmware instance) machine cannot be started with this result: Volume group 'smosvg' not found. (see attachment for details)

Any ideas?

--

Martin

Advertisement

Have you installed patch 8 on the 5.3.0.40 before moving to 5.4?

Maybe you run in CSCuc93106...

Edit:

Ehhmm... unlikely.

Tags: Cisco Security

Similar Questions

  • Upgrade ACS 4.1 and 4.2 authentic session expired: challenge not supplied by the customer

    Hello

    I upgraded Cisco ACS 4.1 to 4.2, I device Cisco Access Control 1113, as soon as I upgraded I get error in newspapers failed

    "Authentic session expired: challenge not supplied by the customer ', what is wring with that? Plesae help me

    Thank you

    I would really appriciate if mark you this topic as resolved so that the other can take advantage out of it.

    Kind regards
    Jousset

  • I was downloading the upgrade to Adobe Bridge. It failed with the error 49. What now?

    I was downloading the upgrade to Adobe Bridge. It failed with the error 49. What now?

    Mcarlclapp the error States just error 49 or does a download error as well?  Also, what operating system are you using?  Finally, you are on a managed network?

  • With Cisco Secure ACS for Windows GANYMEDE +, authentication fails with AD

    I'll put up a Cisco Secure ACS 4.2 server to act as a RADIUS server for switches and routers I use Windows 2003 server for the candidate countries.
    and an Active Directory of Windows 2003 server.  The ad server is very good, it is used for many other things.

    I've implemented ACS as defined nit it installation guide, including all the steps in the "Member Server" section of the installation guide
    When you use AD as an external database (e.g. setting up services to run with a domain administrator account, set up a machine called "CISCO"
    on the field, etc.).

    I've set the unknown user policy to use the database of Windows, if the internal database does not contain the details of the user.

    If I add a user to the internal database, authentication goes through fine, with an entry in the journal "Authentication," spent

    02-24-2010, 05:07:03, authentic failed, eXXXX, Network Administrators (NDG), X.X.X.X, (default), internal error, (get the internal error error message)

    I scoured google etc and just cannot come up with any reason why this should be the case.
    I followed all of the installation to the letter guides.  I need to get this up and running as soon as possible,
    so am eager to know if someone can help me with this one!

    Thanks and greetings

    Sharan

    George,

    Internal error is fairly generic, but a common situation, we see this error is when ACS is installed on a

    64-bit computer.  ACS would not work with the active Manager when it is installed on the 64-bit before machines

    ACS 4.2.1.

    -Jesse

  • It is free upgrade acs 5.0 to 5.1

    We recently bought an ACS ACS 5.0 1120. This time 5.1 is out, can I download it and upgrade my ACS?

    THX.

    Yes. The same license can be used for the 5.0 and 5.1

    In order to perform this update, there are a few tasks that need to be installed before the upgrade to 5.1

    (1) patch ACS 5.0 9. The OCC: 5-0-0-21 - 9.tar.gpg

    (2) ADE-version 1.2 / / / OS version operating system upgrades. The OCC: ACS_5.0.0.21_ADE_OS_1.2_upgrade.tar.gpg

    These two steps, use the following command "acs patch installs the patch name. "tar.gpg repository repository-name "

    Can then upgrade to 5.1 using following command:

    application upgrade Application-bundle name-directory-remote

    All the bundles of patch/upgrade can be downloaded EAC. 5.1 the package is called "ACS_5.1.0.44.tar.gz".

    More documentation detaield is to:

    http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_system/5.1/installation/guide/csacs_upg.html#wp1167547

  • ACS command 4.1 authorization failing intermittently

    Hello

    I have installation switches aaa using Ganymede + on the network, however I seem to get occasional command authorization error. It shows when I try entering the command on multiple ports at the same time (example interface range giga 1/1-48). If I had to do on one lane instead, I does not seem to encounter the error. It would be because of the ACS, unable to carry the load? It is only for a single switch to run the command for port ranges.

    I've attached an example of the error of reference:

    switch (config-if-range) #description level 3
    % Failed authorization.

    % Command failed on the beach of the interface. Abandonment

    I checked the interface to connect to the ACS, and I see no error. I'm not too sure of what may be the cause of error. Would it be because of the ACS unable to work well with the range of interface?

    Thank you.

    There is a bug open for this issue which is found in subsection 12.2 (46), and for the moment there is no plans how to solve the problem because it involves a design work in the code to fix this. The only work around is to remove permission to order or to see what your limit is on the beach inteface command entered begins to drop requests.

  • Upgrade ACS 5.1 to 5.3

    Hi all

    I need to upgrade our ACS 5.1 to 5.3 after I see this cisco Dockment this Doc is more complex

    http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_system/5.3/installation/guide/csacs_upg.html#wp1199421

    I don't understand any help please think of me answering my question

    1. we have 2 primary and secondary, with which we have to start to upgrade?

    -at the top, Doc started with

    Upgrade a deployment ACS 5.1 to 5.3

    2 - sholud I start using this method ACS upgrade deployments or sholud I use only a 5.1 to 5.3 ACS server is upgraded ?

    3 - frist I must save my server how to back up the two page server web ACS server or should I use ony command line?

    -This command

    Step 1 Save the ACS since the ACS 5.2 Server data.

    Step 2 Enter the following backup EXEC mode to perform a backup and place the backup in a repository.

    backup backup-name-name of the repository repository

    4. What is the name of a repository and how do I find

    5. also

    ACS, install patch patch - repository name.tar.gpg repository-name

    -Idon't know whatever that means

    Note

    Before upgrading a secondary server, you must cancel the registration of the primary server.

    6. what it means, what strike?

    7. I can take this update of the page Web directors of ACS

    8. If I need to upgrade our CMD ACS must install FTP server? How to install the FTP server in ACs or how to talk about this ACS server FTP

    Thank you all for the help

    AHA

    Tarik, great answer + 5

    Hello Abdullah Hashim

    You start by secondary. If he's a collector of newspaper and then move it to primary school for a while, once the upgrade has completed, bring it back to secondary, and upgrade of the main box.

    He recommended latest patch on the current version (to avoid known problems) before you upgraded to 5.3 or 5.4 GBA

    You are already using the latest patch of ACS 5.1 (IE patch 6) so you do not need to install another patch. ACS patches are cumulative, so no need to install the previous patches. The last being should have correct all defects.

    Let me know if you still have any questions.

    ~ BR
    Jatin kone

    * Does the rate of useful messages *.

  • Upgrade to Adobe Pro DC.  Failed hard drive.  Now can not find Adobe Pro DC.

    I had Adobe Acrobat XI.  In October 2015, I paid for and downloaded an upgrade to Adobe Pro DC.  My hard drive has failed, and now I don't know where to download the upgrade.  I registered on my Adobe account.  I can see the purchase and the link for the download, but when I do it download Adobe Acrobat XI.  I'd appreciate any help you can provide.

    Thanks in advance,

    Divina

    Available downloadable Setup files:

    Download and installation help links Adobe

    Help download and installation to Prodesigntools links can be found on the most linked pages.  They are essential; especially steps 1, 2 and 3.  If you click on a link that does not have these listed steps, open a second window by using the link to Lightroom 3 to see these "important Instructions".

  • New Fusion 8.02 Upgrade large / Win 10 update installation fails

    Hello

    27 "mac OSX in early 2012 10.11.0 and recently upgraded to Fusion 8.02 and tempted to upgrade 8 Win Win 10 and the upgrade fails with a message that says:

    "Compatibility issue:

    This PC cannot run Windows 10 here's why: VMware SVGA 3D

    Production of the display did not your screen compatible with Windows 10.  Check with manufacture for support".

    I have unchecked the selection of 3D graphics accelerated display Fusion settings, stop the machine virtual, rebooted and tried the upgrade to win 10, but always the same failure message.  I thought I read on Fusion 8 was ready to win 10, but I could be wrong.  Has anyone else had this situation? or suggestions for what I should do to correct the Win 10 upgrade failure.

    Corrective thanks in advance for any advice.

    BG

    Hello

    Please read the article here as it has a workaround:

    http://www.mikeroysoft.com/Windows-10-and-VMware-Fusion/

    --

    Wil

  • 6.1.4 NSX upgrade to 6.2.0: DLR fails to upgrade with DHCP relay message

    Hey all, in the middle of an upgrade of non-prod to a greenfield 6.1.4 6.2. Did the Manager NSX, and follow-up of all controllers. Then after the VMware recommended upgrade sequence, I did the GSS. Then began the DLR. When you try to upgrade the DLR, I received an error message

    The "Upgrade Version" operation failed for the entity with the following error message.

    [DHCP] To enable DHCP Relay, DR instance must be created with a single connected LIF.

    NSX-Training2015-09-07 13_06_51.jpg

    Also, the router now displays status in the NSX edges pane: "failed to create/update edgeAssist interface for edge edge-3.» 404 not found. »

    NSX-Training2015-09-07 15_03_09.jpg

    So I tried erase the configuration of DHCP on the DLR with the button relay remove, no dice. Tried to redeploy, fail with the same message. Tried to force synchronization, changes in status to "impossible to force synchronization. NSX Edge edge-3 is in poor condition. Try the operation again. The DHCP configuration disappears, but the change seems never commit, because when I browse the bracing or routing section and browse to the DHCP relay page, the original configuration is still there. It is a simple DLR with no configured HA. I have attached the newspapers of DLR tech support in case there is any support curious people out there. Note, vCenter 6.0.0 2741530, ESXi 5.5 Patch 5 reissue 2718055.

    He was just going to remove the DLR and re-create it since it's a lab, but if it wasn't a lab I just want to know why it's a failure.

    After reading more carefully, I apparently missed a step in the upgrade (hosts). I suggest that whoever does the upgrade follows the upgrade guide in pubs located here: 6.2 NSX VMware vSphere Documentation Center

    • Manager of NSX upgrade to 6.2
    • Upgrade of the Cluster controller NSX to 6.2, check the status of cluster control
    • Upgrade the cluster hosts for NSX 6.2
    • 6.2 the NSX border upgrade
    • Guest Introspection to NSX 6.2 update
    • Remove the NSX data security and redeploy

    So I tried a lot of things to work myself back from that. I tried to upgrade the hosts but that didn't fly, esx-vxlan has been blocked to version 5.5.0 - 0.0.2691051. To return to a viable State in the end I had to nuke basically the GSS, logical switches, DLR, TZ, manually uninstall the NSX vibs and unsubscribe manager the NSX to vCenter in the cluster take-off of the State of "uninstall." From there, re - install the 5.5.0 - esx-vxlan 0.0.2983935 (6.2) vibs on the cluster worked OK, and I rebuilt the gateway routing and dashboard. So read before making anywhere near prod. : )

  • Impossible to install Dreamweaver CS6 Upgrade! Hard Drive dump - error: failed to check for genuine Adobe software

    Hello

    I am unable to install Dreamweaver CS6 upgrade from versions CS4 Hard Drive DUMP-

    Error: failed installation

    Verification for genuine Adobe software failure

    The product you want to install is not a real software from adobe and seems to be counterfeit.

    .....

    Can someone help me with this question. I installed earlier but DVD, I am unable to find the DVD. I have a copy of full dump DVD network.

    Can someone help me solve the problem.

    Note: I installed Dreamweaver CS4 with serial number number.and try to install the upgrade to cs4.

    Help, please.

    Thank you

    Sin

    It was because I was installing directly from network dump.

    I managed to install and register the software.

    Thank you and my problem is solved.

  • Upgrade process works on Snow Leopard, fails on Lion

    So I bought the upgrade to 7.0.1 (PPC version) on my old Mac Book Pro under Snow Leopard, Acrobat X. It installed correctly and accepted the old license on my older machine, which is loaded with the (7.0.1) OS version that supports always code PPC. However, I can't seem to load and accept the license even on the new machine. Because I can not install the old copy from Adobe on my new machine, as Lion can't stand not all PPC apps, the new upgrade fails. I tried to copy the old product more to my new machine just to see if something in the code would allow new software to find, but it fails.  To be clear, it * works * on my old laptop, so old my mother in law license was valid (I was worried she might be licensed to teaching or something). But it will not accept the old license on my new laptop. Does anyone know a solution to this? A kind of workaround? Adobe can provide me with a valid license that does not require this old code, since in the future, I'm having this same problem on newer machines?

    Well, that is a good question. I liked the idea of being able to open and edit PDF files that people could send me. PDF to Word and Excel.

    But for the life of me, I have not needed more than maybe once in recent years. I sold the computer today and let the application on this subject, with the warning that he cannot be upgraded. Overall, I think that Adobe does a good job of customer service, on equal footing with Apple, in my humble OPINION, and my experience is pretty much an outlier. I assume that in the world of statistical analysis, they can afford to have me have an experience like that, because it is unlikely to be repeated much. If it was 2 k $, I could have raised a little more than a line. For example, its legal application of Framemaker, is completely unable to be upgraded at this stage. Thus all writing she did must be retyped so let's revive old books it publishes. Maybe we can send to the India since no one seems to want to support jobs in America more (G). Adobe seems not to want to upgrade funds, and so it goes. In any case, we consider this case closed. If I'm a little irritated, it's a minor issue and not a rant. Detective Conan.

  • Upgrade to Firefox 13.0.1 failed

    Hello
    I tried to update to Firefox 11.0.1 to 13.0.1. After downloading, when he asked to restart, the computer never shutdown properly. I had to cold start. When I try to continue the upgrade process, it takes over again where it asks to restart the computer, so he is stuck in a loop. How can it be upgraded complete successfully?

    It should never be necessary to restart the computer to update Firefox.

    If necessary then you probably have some security software that is using or the protection of the files in the folder of the program Firefox (C:\Program Files\Mozilla Firefox\) changes.

    Do a cleaning (re) install and delete the folder of Firefox (C:\Program Files\Mozilla Firefox\) program to ensure that all the files are deleted.

    Download a new copy of Firefox and save the file to the desktop.

    Uninstall your current version of Firefox, if possible.

    • Do NOT remove the data personal when you uninstall your current version of Firefox, because all profile files will be deleted and you will also lose your personal data such as bookmarks and passwords from other versions of Firefox profiles.

    Delete the program folder Firefox before installing newly downloaded copy of the Firefox installer.

    Your bookmarks and other profile data stored in the Firefox profile folder and will not be affected by a relocation, but make sure that you do not select delete data of a personal nature if you uninstall Firefox.

  • Upgrade to 8.1 Windows keeps failing - error 0xC1900101

    I can't upgrade to windows 8.1, that it gives me this error after sign in again:

    "Could not update for Windows 8.1.

    Sorry, we could not complete the update Windows 8.1. We have restored the previous version of Windows on this computer.

    0xC1900101 - 0 x 40017.

    The funny thing is that a few weeks ago, I've already updated to windows 8.1 but because of a bad driver and not being able to boot into safe mode, I had to renew my windows and upgrade to windows 8.0. But now I can't update to windows 8.1 more. I installed all the updates of windows, even those in option. So I did a factory reset and uninstalled everything which has not appeared necessary for windows, so the update go smoother. I found a page from toshiba with a tutorial for upgrading to 8.1 and it told me to uninstall the following:

    Genesys Logic
    Intel PROSet
    Intel Wireless Display
    Realtek audio driver
    TOSHIBA PC Health Monitor
    Realtek WLAN driver
    Realtek Bluetooth Filter driver

    and on another page he told me to uninstall anything related with toshiba so I did it all and these are programs I currently have:

    http://oi58.Tinypic.com/2ak028l.PNG

    I also tried with a clean boot but still no change. My atm graphics driver is version 8.9, while the newer version is 13.12 but toshiba not unlock updated 12.1 for windows 8.1 and I tried to install that, but he just in an endless loop of startup.

    My laptop:

    Toshiba Satellite C855-255
    PSCBYE-05000NDU

    You guys could help me please? I'm not sure what I'm doing wrong.

    Post edited by: Alicay

    Someone of your guys already check and read the solution posted in other threads here in the forum?
    http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=74631

  • After the upgrade to v8, unloaded ActiveSync application fails for Windows phones...

    We have improved our 4600 to v8 Saturday.  We have an application relieved for Exchange ActiveSync and since the upgrade, Windows phones cannot synchronize and... an error message "error code: 80072F78.  iOS and Android devices seem to work OK.

    Roll back firmware with exact same parameter to 7.5 and Windows phones reconnect properly.

    Thank you for reporting this issue.

    We are able to repro the issue and is currently under review. Please stay tuned for further updates.

Maybe you are looking for