Upgrade can not display drivers - Satellite Pro U200-10J
Hi all
I recently received a Satellite Pro U200, which I am very satisfied so far.
My current display drivers are the 7.14.10.1147 of the 945GM Express chipset Intel. The new drivers that have been added to the drivers on the Toshiba site list 17 and are the 7.14.10.1227. Unfortunately, they install! I get a message just after the initialization of configuration that these drivers are not the most appropriate for this laptop and it closed facility. When I try to update the Device Manager, it simply tells me that I already have the latest drivers for my machine.
Please notify; p
Hello
Before you start installing the new driver remove the old. You can do this in the properties of the device in Device Manager.
I did it with my Vista preinstalled Satellite A200 (also with the Intel graphics card).
Tags: Toshiba
Similar Questions
-
Windows 8 to 8.1 upgrade is not possible on Satellite Pro C850-1MX
Hello Forum users,.
Sorry for my bad English. I'll try my best ;-)
I'm trying to upgrade Windows 8.0 8.1 on a Satellite Pro C850-1MX.
Before that I removed:
-Realtek Audio Driver
-Realtek WLAN Driver
-Bluetooth filter Driverpackage
-Toshiba Health MonitorI also checked the notebook with the update of the Windows Advisor 8 / attend.
Whenever I try the update is installed, the computer restarts and says while the previous version is restored because the update failed (0xC1900101 & 0 x 30018).
I tried to restore the laptop to factory (using the recovery partition), deleted the drivers, tried again. Same failure.
Where is the problem?
Someone at - it an idea?
I Don t know what to do then.Thank you!!
Thiemo
Hello
Upgrade the win 8 to 8.1 win, to follow some step by step instructions:
This can be found here: [how update of Windows 8 for Windows 8.1 | http://www.toshiba.eu/innovation/generic/windows8_1-upgrade-stepbystep/]Note: after installing Windows 8.1 drivers Toshiba and tools needs to be updated in the correct order.
The Win 8.1 driver installation instruction can be found on the page of the Toshiba UE driver you laptop model section. -
Can not start my Satellite Pro A10
I have a Toshiba laptop Satellite Pro A10. When he tries to start windows, it comes up with the "We apologize for the inconvenience, but windows did not start successfully" etc. I tried all the options for example
Start:
Safe mode
Safe mode with networking
Safe mode with command prompt
Last known good configuration
etc.None of the options works. All I get is a flow of information about drivers and it then hangs. The last driver in the list is:
multi (0) disk (0) partition (1) \WINDOWS\System32\Drive rs\Mup.sys
I can't clear the checkpoint.
Unfortunately, I can't find the disc that came with the laptop, so I'm well and truly stuck.
Any suggestions?
See you soon
HI Leon,
It is quite normal that there is a list of drivers displayed when you try to boot into 'safe' mode However, if initialization fails, obviously there is a problem with your operating system and your only options are to try to fix the problem by using the recovery console (you will need to boot from a CD of original Microsoft installation), or you can restore the original Toshiba CD recovery full operating system.
A third possibility would be to start with a utility such as Norton Ghost or Acronis image backup/restore and restore a backup previously taken by an external device.The simplest option is to restore from a backup that is already taken, but if you don't then you would be better restore from the recovery CD Toshiba you can get at any Toshiba authorized Service partner.
Kind regards
-
No wireless connection - can not operate the Satellite Pro M40
Hi, first Post so hope I understand that I have Satellite Pro M40 A desktop connected to the router via Ethernet cable computer laptop used in another room with a Wi - Fi connection, I guess that means I had a wireless network? Re-installed Win XP and Service Pack 2 as I couldn't find Toshiba rescue disk now I have no sounhd or wireless on laptop something is obviously missing can not remember what I'm supposed to excuse the ignorance, but any help would be appreciated thank you I use the ethernet cable temporarily to access internet on Sat Pro thanks Derek
Hello Derek
If some components of hardware in Device Manager not preloaded properly visit the Toshiba download under http://eu.computers.toshiba-europe.com page > support & downloads.
You will find all the necessary drivers (WLAN and his driver). When the wireless network adapter is correctly installed, you will be able to configure the WLAN connection.
-
Can not get my Satellite Pro L10
I have a satellite pro l10, I tried to put my recovery disk in and she said keeping key c down when I start my computer but it does, nt work, how do I get this drive to work does anyone have an idea, s Please
Hi James,
Press and hold the 'C' key is a specific shortcut of Toshiba to allow the laptop to boot directly from the CD. However, you can also select the CD-ROM as boot device in the BIOS, just press the F12 key when you see the Toshiba start screen for power over the process and you will be presented with a menu of the device selection. Tab just down to the CD-ROM and press to enter. The laptop computer should now boot from the CD.
Kind regards
-
PCMCIA does not work on Satellite Pro U200 with Vista
Hi I have upgraded to Vista family premium on U200 and up to now, almost everything is fine.
However, I have 2 PCMCIA issues that are bugging me:-Any cause of inserted card PCMCIA machine to slow down considerably and mouse movement etc becomes juddery. This is particularly serious if I insert a Toshiba PCMCIA hard drive or a card reader.
-J' have digital TV card to PCMCIA havea for which I can't find the Vista drivers. It works fine with the drivers XP however I get horrible squealing sounds and treble beeps high for a minute or two each time I have change the channel. The card is a generic of an OEM supplier.
Any help appreciated.
Have you tried to update the BIOS or change settings in the BIOS?
The u200 Pro has been delivered with the Toshiba BIOS I hope
On the second page of the BIOS, you can try to change the mode of PC Card controller. You may notice improvements.For digital pilot card PCMCIA TV in Vista, you must ask the card making or visit the support page sorry that's all I can suggest
-
Thin blue line on the display on Satellite Pro U200
My laptop screen has suddenly started to show a thin blue line that goes up and down the screen, so that it does not interfere with the details of the screen it is very annoying and I d rather try to get rid of it.
Has anyone seen this happen before?
My first idea was a display problem, but this problem could be linked to the fault of the graphics card too.
So how can I test?
Well, you can connect an external monitor to the laptop.
If the same thin line will appear on the external display, a graphics card problem may be possible.In both cases, the hardware must be replaced. I think that it s time for the guy to ASP.
-
Upgrade SSD on Satellite Pro U200
Hello!
I have a laptop (Satellite Pro U200-PLUA1E-00X007HU of the v3.70 win7 32-bit bios), I want to upgrade with a series of Samsung 830 64 GB SSD. I read that the SSD need AHCI mode. My laptop supports AHCI mode? What can I change in the bios before installing the new storage?
Thanks for the help!
Robert
Hello
I see you're confused
First, he must know that the laptop supports the SATA controller.
This means that you must use hard drives SATA or SATA SSD.Second: AHCI means SATA some BIOS supports only a SATA mode, and you can switch between compatible (IDE) mode and AHCI (SATA) mode.
If this switch is not available in the BIOS mode is always set to AHCI.
However, to SSD drive question:
I put t really no problem using an SSD.
It must function as the SATA controller support -
Satellite Pro U200: WLan Hotkey Fn + F8 does not
I can't the keyboard shortcut (Fn + F8) working on the Satellite Pro U200 wireless. It worked before, but after that I reinstalled the system and drivers, it no longer works. Any other combination Fn + FX work very well.
If the wirelles (on the right side of the laptop) switch is off and you press Fn + F8, the system displays the following message: "wireless communication is disabled. Please activate the wireless communication switch. "If the wireless switch is enabled and you press Fn + F8, nothing happens (whereas before I was able to activate bluetooth and WiFi card and turn off).
I don't know, but I suspect that the keyboard shortcut no longer works after update BIOS version 1.2 to version 1.3, but I can't confirm this, because I can't downgrade the BIOS and I reinstalled the system, shortly after the update of the BIOS. Do you have any ideas please?
Thank you for your help,
Jiri
Hello
It has worked before, because you used the preinstalled recovery image that contains all the necessary tools and utilities. If you install own OS please consult document instructions facilities and check if software list is missing. You can also use the Tools & Utilities CD and install all stuff on the left. This way you will have perfect configured unit.
Anyway, check it please if you forgot to install Wireless Hotkey V2.0.0.6.
Good bye
-
Satellite Pro U200-10I: DVD UJ-850 s player not working - corrupt/lack of pilot
Hello
I just bought my new laptop Satellite Pro U200-10I. The DVD doesn't seem to work at all. It is said, Mat * a s DVD UJ-850 drive not working - corrupt/lack of driver. Help, please.
Appreciate your response. Thank you!
BAHI
Hello
The CD/DVD drive using the Microsoft diver who is included in the Windows operating system.
According to this page or some registry keys are corrupt windows clean driver failures.I think that you must first access the Device Manager and check if the CD/DVD drive is displayed correctly.
If you do not see a yellow exclamation I recommend to remove the drive from Device Manager and reboot the laptop.After restarting again the OS should recognize the new device (CD/DVD drive) and should implement the drivers again.
Finally start the registry and delete the Upperfilters and Lowerfilters completely from the following registry key values:HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
and restart the device.
Good luck
-
Get the error message when you try an upgrade to Vista on Satellite Pro U200
Hello
When I upgraded my Satellite Pro U200 to Vista (original CD using Toshiba), I couldn't install Config Free program. When I want to install it, I get the message 'the installation image is not corrcet' ideas for this problem?Thank you
Hello
Maybe you need to download again the configfree for your machine from here:
http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp
Just download and try to install it. I can't imagine that she won´t, I ve updated work my A100 some time ago and everything works fine.
BTW. I downloaded all the stuff from the link above.Please give some feedback
Greetings
-
Satellite Pro U200 - hard drive upgrade
Hello
I have a Satellite Pro U200-128 and you want to upgrade the hard drive. I can't find detailed specifications to show me the compatibility, drive type and therefore the size of a disc that I can buy.
I think that its SATA, but there is a lot of info on SATAII, not sure if it will work in my model?Any help appreciated
Hi ollieg72,
You re right. Satellite Pro U200 already uses the HARD drive with SATA interface if you need a HARD SATA 2.5. In addition, it should be possible to use every ability because on SATA interface, there is no capacity limit.
Anyway, SATAII HDD is also working because they are compatible to the old interface of SATA1 downgrade. So it makes no difference if the HDD is SATAII interface or not. ;)
-
I have some problems with my Satellite Pro U200 (WinVista, BIOS 3.50, Display Driver 7.14.10.1217).
After the exit mode standby, the display shows the correct resoluion of 1280 x 800 for a second and then goes to 1024 x 768. It's very annoying.
I tried to uninstall / reinstall the display driver, but it did not help.
Does anyone have an idea?
Well, I remember a similar problem happened on U200 with Windows XP and Windows XP MCE.
The update of the graphics to the version 6.14.10.4543 driver has solved this strange switchingMaybe the next update of the graphics card driver will clear this issue
-
Satellite Pro U200 - need drivers HDD Protection & footprint of VISTA 64-bit
I have toshiba Satellite Pro U200 [Greece] and I need drivers for fingerprint utility and disk protection hard can you help me? It is very important too me.
I think that gives you about boyfriend chance seems Toshiba 64-bit tools and drivers at the moment unfortunately, nothing to see :(
-
Satellite Pro U200: My safe file does not open
Hello
Running XP Pro on a computer Satellite Pro U200, I have installed Norton Ghost 10 (after a lot of difficulties that I had to uninstall Norton anti-siphoning I've ever used on the machine).Subsequently the 'My Safe' folder does not open. Normally when double clicking it asks a fingerprint or a backup password but now it shows just an hourglass for a millisecond and then's there!
Can anyone tell what he might have to get this service running the settings?
Best regards, RobertHey Buddy,
may I ask what 'secure record' this is? This file has been accidentally created by Norton Protection System?
So you have this fingerprint software which manages your fingerprint and your access in the system, etc., etc... ; have you checked if something in this software changed?
A trial might reconfigure these programs.Welcome them
Maybe you are looking for
-
I've demonstrated, creating an application with help forum and guides, however, hit a problem with regard to the screens. My application is configured as follows, import net.rim.device.api.ui.*; public class loginMain extends UiApplication { public
-
Curse of montezuma always ends by itself after a large explosion on the screen, can anyone help me please? Thanks heaps, Andy
-
OEM of Windows 8, fatal error C0000034 of Code
Here's my situation: I have a laptop of Acer M5 w/touchscreen that is preinstalled with Windows 8. The laptop doesn't boot for me with the following error: Fatal Error Code C0000034 (application of update 10 $ 378 .cs-msf)The problem started when I r
-
Mr President.I create a form based on two tables that have sequences also. When I create insert only row is inserted in the fields in table first and second fields of the table are empty. Why?the page source is <?xml version='1.0' encoding='UTF-8'?>
-
Hello! I use a PC and have problems loading my homepage of Muse. First of all, I made one with the address "nordensstjarnor" and updated several times without any problems. And once, I couldn't download on 'nordensstjarnor' any longer. Don't know why