Uplink Network \Network connectivity redundancy lost lost

Hello

I have hp servers and they down due to electrical problem, and after that they up, I got these

(redundancy uplink of lost network connectivity lost \Network)

and I have on each server 1 standerd switch 8 vmnic 4 wrkking and 4 pending and I checked all, but I have not found any problem on any

so please can anyone advice what is the problem

Thnx for your support

Hello

Try alarm reset to green...

Thank you

SA

Tags: VMware

Similar Questions

  • When I'm trying to connect to itunes, I get a message on my computer that says, we can complete your itunes application.  The network connection is lost.

    When I'm trying to connect to itunes, I get a message on my computer that says, we can complete your itunes application.  The network connection is lost.

    Try If you can not connect to the iTunes Store - Apple Support.

    TT2

  • Satellite Pro P200: network connectivity is not stable

    I have a Satellite Pro P200, which was downgraded from Vista to XP Pro SP3 corporate.

    I use a sensitive enough network application that will crash when network connectivity is lost.
    This application has been blocking a lot since I downgraded to XP, so I tried to run a continuous ping that gave rise to many messages Request Timed Out (the maximum number of attempts where I actually had ongoing responses was about 30 but is usually much less).

    I use the driver downloaded from the Support from Toshiba site (Realtek RTL8139/810 x Family Fast Ethernet Nic - v5.664.205.2007), wireless network works fine, tried to connect to the network using a cable and a port different without change, and using a different laptop with the same cable and port works fine.

    The yellow exclamation mark in Device Manager is a memory PCI controller which I believe is for the Intel Turbo Memory, because it is not compatible with Windows XP.

    Any ideas what could be the cause.
    I tried reinstalling the driver several times without success, it is likely to be software partners or could it be a hardware failure?

    I think it's related software and troublemaker is SP3. Test it with SP2 only and it will work perfectly. Friend of mine noticed permanent data LAN transfer interruptions after installing SP3. Remove everything works well again.

  • Alert - lost redundancy Uplink Network trap

    Is there a way to find this alert via PowerCLI?  I often get this alert and need to put in place an alert by e-mail when this happens, but I do not Get-VIEvent but it is in the console under alarms.

    To obtain the host name, you can do it like this:

    Get-VIEvent -Start (Get-Date).AddDays(-7) -MaxSamples 99999 | `
    Where-Object {$_.GetType().Name -eq "EventEx" -and $_.EventTypeID -eq "vprob.net.redundancy.lost"} | `
    Select-Object -Property EventTypeId,Severity,CreatedTime,@{N="VMHost";E={$_.Host.Name}}
    

    Best regards, Robert

  • "Network connectivity lost" alert - how to find which NIC is it?

    Hi, we cluster with VCenter 5.5 HA and 2 X ESXi servers.

    Each host has 4 NIC

    One of the host's alert 'Network connectivity lost' that was triggered 02:00 in the morning. Is to verify that NIC is this anyway?

    The events tab says know as NIC.

    Any help would be appreciated, thanks.

    You should see some sort of event in the user interface and the vmkernal.log and vobd.log.


    VMkernel.log

    ~ #vmkernel.log | grep "link down"

    2014-11 - T 05, 20: 17:20.770Z cpu0:33263) netsched: NetSchedMClkNotify:2329: vmnic1: link down notification

    ~ #vmkernel.log | grep 'link up'

    2014-11 - T 05, 20: 17:33.314Z cpu0:33265) netsched: NetSchedMClkNotify:2321: vmnic1: link notification

    2014-11 - T 05, 20: 17:33.656Z cpu1:33411) netsched: NetSchedMClkWatchdogSysWorld:3786: vmnic1: bind an event received, device operating at 1000 Mbps for the adjustment of the depth of queue to 8646 bytes with bytes 131 expected / us

    2014-11 - T 05, 20: 17:33.735Z cpu1:32808) netsched: NetSchedMClkNotify:2321: vmnic1: link notification

    2014-11 - T 05, 20: 17:33.736Z cpu0:36689) netsched: NetSchedMClkWatchdogSysWorld:3786: vmnic1: bind an event received, device operating at 1000 Mbps for the adjustment of the depth of queue to 8646 bytes with bytes 131 expected / us

    ~ #

    ~ #vmkernel.log | grep "NIC link is Down"

    2014-11 - T 05, 20: 21:25.915Z cpu0:33267)<6>e1000: vmnic5: e1000_watchdog_task: NIC link is

    ~ #vmkernel.log | grep "NIC link is Up"

    2014-11 - T 05, 20: 21:41.660Z cpu1:33268)<6>e1000: vmnic5: e1000_watchdog_task: NIC link is up 1000 Mbps Full Duplex, flow control: no

    vobd.log

    Just did a test for you.

    ~ # tailvobd.log

    2014-11 - T 05, 20: 17:33.418Z: [netCorrelator] 620684191us: [vob.net.dvport.uplink.transition.up] Uplink: vmnic1 is in place. Affected dvPort: 5/a6 eb 07 50 28 7 b c8 5 a - a0 a6 99 e8 ad b 8, 95 6. 1 uplinks to the top

    2014-11 - T 05, 20: 17:33.418Z: [netCorrelator] 620684194us: [vob.net.dvport.uplink.transition.up] Uplink: vmnic1 is in place. Affected dvPort: 5/a6 eb 07 50 28 7 b c8 5 a - a0 a6 99 e8 ad b 8, 95 6. 1 uplinks to the top

    2014-11 - T 05, 20: 17:35.000Z: [netCorrelator] 622285373us: [esx.clear.net.dvport.connectivity.restored] network connectivity restored on DVPorts: ' 5/a6 eb 07 50 28 7 b c8 5 a - a0 a6 99 e8 ad 8 6th b 95', ' 5/a6 eb 07 50 28 7 b c8 5 a - a0 a6 99 e8 ad b 8, 95 6. Vmnic1 physical NIC is in place

    2014-11 - T 05, 20: 17:35.000Z: [netCorrelator] 622285495us: [esx.clear.net.dvport.redundancy.restored] redundancy Uplink restored on DVPorts: ' 5/a6 eb 07 50 28 7 b c8 5 a - a0 a6 99 e8 ad 8 6th b 95', ' 5/a6 eb 07 50 28 7 b c8 5 a - a0 a6 99 e8 ad 8 6th b 95', ' 5/a6 eb 07 50 28 7 b c8 5 a - a0 a6 99 e8 ad b 8, 95 6. Vmnic1 physical NIC is in place

    2014-11 - T 05, 20: 21:26.094Z: [netCorrelator] 853350673us: [vob.net.vmnic.linkstate.down] vmnic linkstate down vmnic5

    2014-11 - T 05, 20: 21:27.001Z: [netCorrelator] 854286718us: [esx.problem.net.vmnic.linkstate.down] vmnic5 of the physical NIC linkstate is down

    2014-11 - T 05, 20: 21:42.149Z: [netCorrelator] 869405317us: [vob.net.vmnic.linkstate.up] vmnic linkstate upward vmnic5

    2014-11 - T 05, 20: 21:43.002Z: [netCorrelator] 870287321us: [esx.clear.net.vmnic.linkstate.up] vmnic5 of the physical NIC linkstate is in place

    2014-11 - T 05, 20: 24:38.723Z: [netCorrelator] 1045972218us: [vob.net.vmnic.linkstate.down] vmnic linkstate down vmnic5

    2014-11 - T 05, 20: 24:39.000Z: [netCorrelator] 1046284854us: [esx.problem.net.vmnic.linkstate.down] vmnic5 of the physical NIC linkstate is down

    2014-11 - T 05, 20: 24:42.230Z: [netCorrelator] 1049478491us: [vob.net.vmnic.linkstate.up] vmnic linkstate upward vmnic5

    2014-11 - T 05, 20: 24:43.001Z: [netCorrelator] 1050286523us: [esx.clear.net.vmnic.linkstate.up] vmnic5 of the physical NIC linkstate is in place

    * Reminder to implement Syslog.global.logHost (software) advanced creation collection newspaper and magazine.

  • network connection lost alarm

    Hello

    alarm sails host shows "Lost network connectivity" and "Network of uplink redundancy lost" errors in vCenter red Rectangle symbol and came on the host, but all VM and servises performs very well what was the reason for this alarm and what is the solution for this.

    In this case it could have been a temporary problem with the network, which is already solved. To get rid of the alarm message, you will need recognize/reset the alarm.

    André

  • App Store network connection has been lost because

    MacBook air early 2015 El Capitan 10.11.6

    Regardless of the service providers network, firewall is turned off, I get "we couldn't complete your purchase. Network connection has been lost"message when I try to install any app from App Store.

    Any help appreciated.

    Try resetting the App Store and the deletion of Cookies.

    Reset       Taken from old Toad

  • Apple Store is not up-to-day - network connection lost

    Hello

    I have a MacBook Pro with OS X El Capitan installed and allows you to connect to the Bank of the United States, where I bought the laptop. I moved to the New Zealand a few months ago and changed the NZ store, and for the last two weeks that I'm not able to update the software through the Apple Store, I always get the message "the network connection has been lost", even if the network is OK:

    My account is active, no problem. I even "bought" a free app just in case and it's all good - I could add to my list of software and download it.

    Any thoughts on how to proceed?

    Thank you

    Fabio

    More info: I already followed the instructions to "If you can not connect to the iTunes Store - Apple Support.", everything is OK - no firewall issues, DNS or key ring...

  • Satellite Pro U400 - network connection lost after suspend

    I have a Toshiba Dynadock. My network is connect directly in dynadock.

    When suspend my Satellite Pro U400 and after reboot to continue working I lost my network connection. Then I shut down my computer and disconnect/connect Dynadock I can continue working.

    What is the problem?
    Dynadock software version is 2.0

    Hello

    I see that you have switched from Vista to XP.

    First of all I recommend you update the BIOS.
    As I m not wrong on the European driver Toshiba page, you should find a newer version of the BIOS.

    You will need to upgrade Win XP to the last State.
    The XP must be up-to-date and all service packs, hotfixes and patches MS must be installed in your laptop.

    Access the Device Manager, and then score in each USB hub root, you must disable the option called allow the computer to turn off this device to save power
    You can find this option in the properties-> tab power management

  • iPod touch will not got to some Web sites - "Safari cannot open the page because the network connection has been lost."

    Safari refuses to go to certain websites (facebook.com, youtube.com) on my iPod Touch and instead displays this error:

    S afari cannot open the page because the network connection has been lost.

    The bubble at the top where I typed in the URL doesn't change, it always says "facebook.com" or something else.

    No matter where I am, so it won't get fixed by resetting my home Wi - Fi router. Other sites load fine. I have reset the iPod, too, by pressing the sleep button and one on the front (whatever it's called) until I see the apple logo. I also did 'Story clear and data Web site' in the Safari settings.

    I searched the web and found a number of threads that start with similar complaints, but I can't find one where the problem has been resolved in fact.

    Thank you!

    Not "no matter where I am," means, it happens with all networks?

    If so:

    Try:

    -Reset the device iOS. Nothing will be lost

    Device iOS Reset: Hold down the On / Off button and the Home button at the same time for to

    ten seconds, until the Apple logo appears.

    -Reset all settings

    Go to settings > general > Reset and tap reset all settings.

    All your preferences and settings are reset. Information (such as your contacts and calendars) and media (such as songs and videos) are not affected.

    -Restore from backup. See:

    Restore your device from an iCloud or iTunes backup - Apple Support

    -Restore factory settings/new iOS device.

    If still problem, make an appointment at an Apple store Genius Bar because it appears that you have a hardware problem.

    Shop Apple Store - Genius Bar

  • Re: The network connection to the printer has been lost.

    I'm having the same problem with a HO Photosmart 5520 and win 10. The solution to this annoying problem is far too complex and time consuming. Instead, it should be an option just to cut the sound notificaiotn.

    Welcome to the HP community @janhoza!

    I came across your post regarding your printer lost network connection and wanted to pop in to help.

    Through your message, we don't have the option to disable the notification. But I think that we can solve this problem by simply assigning a static IP address. Here are the steps:

    • Get the IP address of the printer, you can touch the 'Wireless' icon on the Control Panel printer to get the IP address.
    • Type the IP address in your web browser to get the EWS page on your computer printer.
    • Go to the 'Network' tab - click on "wireless (802.11), and then click «network address (IPv4)»»
    • Click on the box that says "Manual IP", then click "Propose an IP address manually" to give an IP address manually to your printer.
    • Click on the radio button that says 'Manual of the DNS server' and under manual type favorite 8.8.8.8 and manual replacement enter 8.8.4.4 (it is Google's DNS server address)

    Let me know if this helps. Good luck!

    See you soon

    Please click on 'acceptable' on the post that solves your problem to help others to find the solution. To show gratitude for my help, please click the 'Thumbs Up icon' below!

  • OfficeJet 6700 Premium: scan of the computer is that is no longer enabled network connection has been lost

    "scan of the computer is no longer active network connection has been lost" appears every 10 minutes or so on my "[redacted] Compaq 8200 Elite Minitour Convertible" is connected to "6700 Premium e-All-in-one Officejet - [redacted] H711n.

    I have already run the 'Locator solutions and update".  He finds nothing.

    I don't know what else to do.

    Please provide the following information if anyone can help including:

    The printer model - done

    Complete and detailed problem description-

    Operating system on the computer (including service pack revision) - done

    Connection method - Direct wireless, wireless, wired LAN, USB? -

    Brand and model of router and modem? -

    Error messages - on the screen of the printer or computer, no matter what flashing light patterns?

    If wireless, in the event of problem, what is the status of the blue wireless light on the printer, active, disabled or flashing? –

    Power off the printer and the router. Power on the router and wait 3 minutes, power on the printer. It connects to the router now? You have a valid IP address?

  • Troubleshooting ESX 4.1 "lost network connectivity.

    Hi people,

    I made a change in a vSS in the detection of failover network status 'link' to 'Beacon probing.

    Now a have an active alarm with Red State: "Lost network connectivity", but the message in the events of the host does not show that active vmnic of my rising has the problem.

    Sound it no way of knowing which physical interface have this configuration problem?

    Thank you

    ------

    Cabral Wellington

    In addition, if you wish to arrive linkstate changes in your host you can ssh to the desired host (or via the console of the ILO, etc.) and simply grep for 'link' (provides most of output) or "linkstate" (provides a minimal output, only showing the ascent/descent of the events).

    Syntax of the command (depending on the version of ESXi host that you may need to tweak it a bit)

    ESXi 4.x

    cat /var/log/messages | grep -i link
    

    -or-

    ESXi 5.x

    cat /var/log/vmkernel.log | grep -i link
    

    Here are some example output captured everything by making the maintenance of networks:

    ~ # tail -fv /var/log/messages | grep -i link
    Jul 26 16:34:43 shell[372172]: tail -fv /var/log/messages | grep -i link
    Jul 26 16:35:52 vmkernel: 1:00:26:20.001 cpu13:4462)<3>qlge 0000:08:00.1: ql_link_down: vmnic5: Link Down.
    Jul 26 16:35:52 vobd: Jul 26 16:35:52.540: 87980025771us: [vob.net.vmnic.linkstate.down] vmnic vmnic5 linkstate down.
    Jul 26 16:35:52 vmkernel: 1:00:26:20.057 cpu15:4947)sfqosq: del pc member - q_ulink is already NULL, return
    Jul 26 16:35:52 vmkernel: 1:00:26:20.057 cpu15:4947)sfqosq: del pc member - q_ulink is already NULL, return
    Jul 26 16:35:53 vobd: Jul 26 16:35:53.542: 87981034666us: [esx.problem.net.vmnic.linkstate.down] Physical NIC vmnic5 linkstate is down.
    Jul 26 16:38:14 vmkernel: 1:00:28:41.743 cpu8:4455)<3>qlge 0000:08:00.1: ql_link_up: vmnic5: Link Up.
    Jul 26 16:38:14 vobd: Jul 26 16:38:14.432: 88121917666us: [vob.net.vmnic.linkstate.up] vmnic vmnic5 linkstate up.
    Jul 26 16:38:15 vobd: Jul 26 16:38:15.434: 88122926678us: [esx.clear.net.vmnic.linkstate.up] Physical NIC vmnic5 linkstate is up.
    Jul 26 16:39:57 vmkernel: 1:00:30:25.243 cpu0:4947)sfqosq: del pc member - q_ulink is already NULL, return
    Jul 26 16:39:58 vmkernel: 1:00:30:25.541 cpu2:4443)<3>qlge 0000:11:00.1: ql_link_down: vmnic7: Link Down.
    Jul 26 16:39:58 vobd: Jul 26 16:39:58.224: 88225709691us: [vob.net.vmnic.linkstate.down] vmnic vmnic7 linkstate down.
    Jul 26 16:39:59 vobd: Jul 26 16:39:59.226: 88226718868us: [esx.problem.net.vmnic.linkstate.down] Physical NIC vmnic7 linkstate is down.
    Jul 26 16:40:58 vmkernel: 1:00:31:26.091 cpu13:4459)<3>qlge 0000:11:00.1: ql_link_up: vmnic7: Link Up.
    Jul 26 16:40:58 vobd: Jul 26 16:40:58.890: 88286375827us: [vob.net.vmnic.linkstate.up] vmnic vmnic7 linkstate up.
    Jul 26 16:40:59 vobd: Jul 26 16:40:59.892: 88287384684us: [esx.clear.net.vmnic.linkstate.up] Physical NIC vmnic7 linkstate is up.
    

    Note: The example above uses the tail command to follow (-f) mode to observe the desired forensics in real-time (i.e. during your change).  Otherwise, to review historical linkstate changes that have already occurred, and then use the command cat first noted at the top of the pole.

  • ESXi 4.1.0 lost network connectivity?

    For the last 5 days 3 out of 4 of our server show an alarm of "lost network connectivity.  The weird thing is that we have a connectivity total all servers and all virtual servers.  All the lights flash on each swith, port, nic, and everything you can think of.   All the settings on vSwithes are the same with no red x I ran the command esxcfg-NICS-1 and # ethtool - s vmnicX without any problem.  Any ideas?

    There can be question of alarm so... can reset you the alarm and then check.

  • Create alarm "Network redundancy lost" by the script?

    Hello:

    I'm trying to write a script that will create the alarm in order to monitor the redundancy of the lost network (I know manually there) on the host.

    I know how to create alarm for additional exhibit the ' basic' event (LucD - thank you for your help) and I know that I have for alarm 'Lost network redundancy' to use 'vprob.net.redundancy.lost' instead of 'EnteringMaintenanceModeEvent' (as in my example); but I still struggle to combine...

    Can someone help me please?

    Thank you

    qwert

    I don't have a particular script fantasy with the settings and all the rest, but I can show you the steps to filter alarms by name and remove the desired one.

    alarm #retrieve Manager

    $alarmManager = get-view-Id "AlarmManager-AlarmManager.

    #Get the entity that contains the alarm that you want to remove. I'll do it for a virtual machine

    $entityView = get-Vm-name MyVm | Get-View

    #get all MoRefs alarm

    $alarmMoRefList = $alarmManager.GetAlarm($entityView.MoRef)

    #Retrieve tha alarm views from the MoRefs

    $alarmViewList = $alarmMoRefList | foreach (Get-view $_)

    #Now filter the name alrams

    $alarmToDelete = $alarmViewList | where {$_.Info.Name - eq "AlarmToDelete"}

    #Finally remove alarms

    $alarmToDelete.RemoveAlarm)

    It shouldn't be hard to put this in a script or function reussable. If you have problems with this, I'll be happy to help you again!

Maybe you are looking for

  • update not iTunes feed

    I am using Soundcloud to host my podcasts for about a month and have had no problem. Everything is up-to-date on my channel to podcast iTunes as well. However, when I posted my last podcast last night (episode 197) it has not yet updated on my iTunes

  • Re: Trying to update the display on Satellite A305-S6843 ATI driver

    OK, I have aSatellite A305-s6843 64-bit Windows and I have theATI mobility radeon hd 3470 graphics cardI installed the driver version is 8.501.0.0 I want to install the new driver I found and this is the version8.632.1.2000 so my questions1. where ca

  • Problems installing video controller on M40X-233

    I have a Toshiba Satellite M40X-233 and have the following problem: after purchase, I went on this site to get the latest drivers for my laptop. Installed everything ok except the video controller. After installation of this one (Intel controller), h

  • Pogo games are too small

    This happened after having reinstalled windows, as suggested by Microsoft tech rep.I changed the resolution of the screen but no change.

  • Retrieve an activation of a 3 upgrade package because the results were not worth

    One of the computers I upgraded from XP to Windows 7 and activated using a reduction of 3 Microsoft computer kit does not work well enough to justify the change. Can I turn off just an and thus be able to upgrade a different computer later?