Usable memory (RAM) less than the installed memory, showing remove Win7 dual-boot.

Original title: "Memory (RAM): 12,00 GB (3.62 GB usable)", how can I resolve this issue and remove a dual boot Win7?

I recently, after experincing problems (see below the Intel SSD), noticed the system said that there is only a 3.62 GB of Ram available in my computer.  I have this statement ' Installed Memory (RAM): 12,00 GB (3.62 GB usable) "the computer has always used a higher around 10-11 GB amount.

I noticed that the Windows performance index was 5.6, after adding an Intell 240 GB SSD, it jumped to 7.6; However, now with the problems is 5.4, caused by the RAM.

I ran the full memory diagnostics: start-up and verification of memory it says I have 12 GB of RAM can be used across both.  I asked with Asrock if my RAM and CPU compatible before buying it, and they said it was a wise decision for 970 Extreme4 motherboard.  I subsequently has inquired about the Kingston RAM and included information from a - Data, and they said they used Kingston ringout for approval process as with a - DATA, including the compatibility of the different types of RAM used together.  The RAM was tested and is placed on the store of the computer.
This problem did not exist until I installed the Intel SSD.

I don't have a problem with dual boot on my computer after installing a new 7 ultimate on the SSD, and when it worked normally, I atttached the old hd back into your computer, because important data it contains.  This caused a situation of dual-boot.  I did some research and jumped the drive as a slave thinks that it would not cause a problem.  How can I remove Windows 7 from the old hd and then remove the window dual-boot.  I tried the old way to change the startup configuration, however, I can't find it in 7 Ultimate SP1. I also sent the old HD and the start window remained, as the index and the usable Ram 3.62.

My Questions as already said:
How can I return to a usable 12 GB of RAM and return the highest Index of Exp Win?
How the dual boot can be edited to boot from my SSD without window startup and remove window 7 my old HD eventually without formatting?

The system configuration:
Processor: AMD FX FD8300WMW8KHK 95W Vichera 3300 MHz

Memory: ADATA DDR3 1333 AM2U139C4P2 - s 4 GB x 2
Kingston DDR3 1333 KVR1333D3N9 / 2g x 2

Graphics card: MSI GeForce GTX 750Ti Gaming

Motherboard: ASRock 970 Extreme4

Power: 600 W power supply

HD: IntelSolid State Drive 240 GB 335 Series

OS: Windows 7 Ultimate 64 bit SP1.

The version of the BIOS/Date: 32 MB FRIEND UEFI BIOS legal with GUI support version 2.60

NISH

When you are satisfied with your problem is solved, please mark the answer. It helps others see what answered your question.

If you posted the original question, you can mark the question as yourself have. Just click the mark as answerbutton.
Source: http://answers.microsoft.com/en-us/page/faq#faqAskQuestion8

You should see the response from Mark (and have found this useful Me) buttons on all messages, except your own messages, sent by others about your. They are there to allow you to tell other users, messages that you have found useful, and ultimately what solved your problem or answered your question.

Tags: Windows

Similar Questions

  • The message "requires the more recent than the installed version of OS service pack" when you try to install the CA's security program

    Original title: new pc and installation of my security program.

    The message "requires a more recent than the installed version of OS service pack" continues to show when I want to install my program files of security of this technology to my new computer. What should I do? Automatic update that happened but has not changed things.

    Are you sure the Antivirus you are using is compatible with Windows 7?

    What version is this?

    See the developers website for compatibility with Windows 7 and if there are updates, corrections or difficulties that might ensure compatibility.

    Windows 7 Compatibility Center

    Check if your application software or hardware is on the list

    http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

    Software:

    http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx?type=software

  • Less than the date of application


    Than the date of application.

    How to get out the query set so even if a T_DATE is less than the Admission_date the query should display all the data.

    ID T_DATE Admission_date
    101 4/1/2001-5/1/2001
    102 4/1/2001-5/1/2001
    103 4/1/2001-5/1/2001
    104 4/1/2001-5/1/2001
    105 4/1/2001-5/1/2001
    106 6/1/2001-5/1/2001

    Even if a T_DATE is less than the date of Admission, the application must pick up all the data.

    Select * from X where T_DATE < Admission_Date gives only

    101 4/1/2001-5/1/2001
    102 4/1/2001-5/1/2001
    103 4/1/2001-5/1/2001
    104 4/1/2001-5/1/2001
    105 4/1/2001-5/1/2001

    Yet the missing 106.

    Thank you..

    Hello

    You can change the solution in response #2 like this:

    WITH got_ok_cnt AS

    (

    SELECT *- or display the columns that you want to

    , COUNT (CASE WHEN T_DATE)< admission_date="" then="" 1="">

    COURSES (PARTITION BY id) AS ok_cnt

    X

    )

    SELECT *- or the list of all columns except ok_cnt

    OF got_ok_cnt

    WHERE ok_cnt > = 1

    ;

  • Muse cut the part left my site when resizing the window of the browser for anything whether it is less than the width of the page

    When you use centering nychtemerales, Muse cut the left side of my site when re the sizing of the window of the browser for anything less than the width of the page, this also happens on mobile devices.  How can I keep the page focused but have content basically left stop when resizing or viewing on a mobile screen? I don't want the edge of the page to disappear on smaller screens and when you use a smaller window. I do not want to resize the entire site at a lower resolution. Thanks in advancearbubaproblem.jpg

    If the left is cut, then you have designed offshore from the left of the page mode Design of Muse. The blue guides indicate the edge of the page and a margin guide on the page. Rule zero is the left edge of the page.

    The page is not admissible it will focus as long that the browser is wider than the page. Then, she left aligned (on point zero on the sovereign in design mode).

  • How to check the account of a column value is less than the other value of column in a table with a single column

    Hello

    Please let me know how to query the table and get the records that are less than the other column.

    ID item_id item_type

    3     1           r1

    2 4 r2

    1 5 r3

    6 5 r4

    I need to get all the lines in which item_id < id

    o/p

    ID item_id item_type

    3     1           r1

    6 5 r4

    SELECT ID, ITEM_ID, ITEM_TYPE

    Of

    WHERE ITEM_ID<>

  • Store the value less than the current week and the year.

    Hi all

    I have a table called BACK, which structure is like this
    ITEM_NUMBER   YEAR_WEEK   MS
    ...........   .........   ..
    1N58          2012-WK02   01/15/2012
    1N58          2011-WK02   01/15/2011
    current my procedure I store the value in my new table that is less than the current week. But I want to retain the value less than the current week and the current year. Please, help me to get how I can do this.
    PROCEDURE BACKLOG_PROC_LT_CW IS
      BEGIN
     DELETE BACKLOG_LT_CW;
     COMMIT;
          INSERT INTO BACKLOG_LT_CW
            SELECT 
                  DC_UTIL.GEN_YEAR_WEEK(MS) YEAR_WEEK,
                  ITEM_NUMBER,
                  MSD
    
                  FROM BACKLOG
              where to_char(MS, 'IW')<to_char(sysdate, 'IW');
    
      END BACKLOG_PROC_LT_CW;
    Currently, with the above code is to store the value in my table of BACKLOG_LT_CW but if you see the data in the table from the BACK you will find YEAR_WEEk 2012-WK02 falls next year, but again it is store in my table because IW took only. Please help me get the soln

    Thanks in advance

    Concerning

    Are you looking for this?

    ...
    where to_char(MS, 'YYYYIW')
    
  • End date must CLEARLY not less than the start date, else it

    Hello

    I put DATE of BEGINNING of THE CONTRACT and END of CONTRACT fields on the form. These 2 objects (DateTime objjects), I pulled game tab of the palette and fell on my layout, fine design.

    Now, I try to put a validation than the end dat eshould not lower than the beginning, so I had a thread as below from Niall.

    http://forums.Adobe.com/message/1909551

    and I've done my coding FormCalc to the OUTPUT of the END DATE field as event title below,

    Please note that FormCalc
    End date must not less than the start date, else CLEAR-Begin

    var ACE
    var endDate

    As = xfa.resolveNode ("CUSTOMER..") RawValue Page31_Contracts.Con_Whole_Page.CON_Basic_Info.CON_START_DATE")
    endDate = xfa.resolveNode ("CUSTOMER. Page31_Contracts.Con_Whole_Page.CON_Basic_Info.CON_END_DATE") GLR awValue

    If (ACE > endDate) then
    xfa.host.messageBox ("end date is less than the departure date! End date is allowed")
    xfa.resolveNode (the "CUSTOMER". Page31_Contracts.Con_Whole_Page.CON_Basic_Info.CON_END_DATE") GLR awValue = null
    endif

    End date must not less than the start date, else CLEAR-end

    I tried to VALIDATE, calculate, change events of END DATE, but nothing works!

    Can pls. Let me Kow how I optimize my requirement? I'm anewbie,

    Thank you

    If you use the exit event, you will likely have the same code on the date fields beginning and end, because they have an addiction to each other. Maybe better try the validate end date event, so that if a field is changed the event is fired. You can try the following to validate the event

    // Pls. note this FormCalc
    // End date should not less than Start date, else CLEAR it - Begin
    
    var stDate
    var endDate
    
    stDate = CON_START_DATE.rawValue
    endDate = $.rawValue
    
    if ( HasValue(endDate) ) then
        if (stDate > endDate) then
            xfa.host.messageBox("End date is lower than Start date! End date is cleared")
            $.rawValue = null
        endif
    endif
    1
    // End date should not less than Start date, else CLEAR it - End
    
  • Then updates older than the newest one be removed safely?

    original title: I'm removing unnecessary programs from my PC and there are as many old updates MS still displayed in the populous.  Then updates older than the newest one be removed safely?

    When I go into Control Panel, then add/remove programs, there are many old updates ongoing MS.  My question is, can those older newer be removed safely?

    On this issue, see the following web pages:

    http://www.PAGESTART.com/NTUninstall.html>

    http://www3.TELUS.NET/dandemar/spack.htm>

    http://taurarian.MVPs.org/WU_XP/removing_old_windows_updates.htm>

    07/18 / 1106:19:10

  • Try to install Windows XP & Vista in Dual Boot, but Windows XP not fully installed

    Hi friends,

    I have my serious to replace the Windows Vista on my desktop, I created some complications on my computer "dear."
    WIndows Xp has not been completely installed due to a driver error. Now, I have a WIndows Vista and a wrong version of Windows XP.
    I tried to replace the XP, but it seems that I have the following challenges:
    (1) the two versions of Windows (Vista and XP) are installed on one single disc itself, IE. C drive.
    (2) I formatted D drive, whereby a XP driver disappeared.
    In the current context, how can I uninstall the XP then replace Vista with a new version of XP, my C drive has little free space left due to the presence of 2 windows versions.
    Let me know the best way to go, I backed up all the data and data loss is not a concern, is of the order of the day to start!
    Thank you
    Nits

    Hello

    1 how many partitions you have?
    2. which partition do you want to install windows XP?

    3. are you able to work properly under vista?

    You can see the steps in knowledge base articles, and to check whether it helps to install Windows XP.
    http://Windows.Microsoft.com/en-us/Windows/help/install-reinstall-uninstall

    See also the links to learn more about dual boot
    How to create a multiple-boot system in Windows XP
    http://support.Microsoft.com/kb/306559

    Windows XP does not start on a computer that is configured to dual-boot
    http://support.Microsoft.com/kb/315233

    You cannot start Windows XP after you install Windows Vista in a dual-boot with Windows XP configuration
    http://support.Microsoft.com/kb/927817

    I hope this helps.

  • Bridge is very slow on iMac with El Capitan, using 75% less than the 32 GB of RAM.

    I have a new iMac 27 inch Retina 5 K (end of 2015) 3.2 GHz with 32 GB of RAM and bridge is now used in the region of 20-25 GB + of it on a regular basis. My previous iMac 24 inch (end of 2009), with 'only' 8 GB of RAM, ran faster and the RAM usage was less than 45%. While Bridge works very slowly - much slower than my old iMac - and I can't work out why.

    I compacted and emptied the cache, reduced the number of images in each folder and reduced the size of the preview, but nothing seems to make any difference. I forgot something or are my expectations too high? The bridge is my main tool with Camera RAW/Photoshop before importing all the files in Lightroom and speed reduction is initially serious workflow problems.

    Someone a suggestions please?

    Hello

    Greetings!

    See this article: https://forums.adobe.com/docs/DOC-6301

    Concerning

    Jitendra

  • date is not less than the current date.

    Hello, I have a form. He has an element called end_date. I want to have the validation of end_date that 'end_date should not less date day'. Advice would be useful.

    Thanks in advance.

    jwellsnh wrote:
    Alexander,

    Dynamic action, execution of JavaScript to do this:

    Create a dynamic Action:
    Event present before the Page
    JavaScript Expression condition
    Value

    $v('P1_END_DATE')<$v('P1_BEGIN_DATE')
    

    In this scenario; P1_BEGIN_DATE will sysdate as default and can be hidden on the page.

    Jeff

    Published by: jwellsnh on July 19, 2012 09:50

    Maybe I'm missing something, but is it just a case of use for a validation? Would be curious to know why you thought of javascript rather than a normal integrated functionality (not designed as a criticism by the way!) - is javascript your first port of call when it comes to APEX?

    I would also watch you comparisons to SYSDATE - remember that SYSDATE including right now, so you must consider (perhaps you could make use of the TRUNC function to remove the element of time?). Indeed, javascript did not assess this expression as comparing two dates (I know that Javascript evaluates variables byDuck Typing but it works in practice)?

  • Capacity again VMFS is less than the total capacity of all extensions

    I recently created a new VMFS whose total capacity is not displayed. The "storage adapters" show all extensions.

    Total capacity should be well over 4 TB. However, when I look in the 'Storage' view, I see a little more than 3 TB of capacity.

    I just updated this server the latest patches for ESX 3.5 and restarted the problem remains. Any ideas what's happening?

    --

    Michael A. Lowry

    mlowry.blogspotcom

    Hi Michael

    I do know that if I missed something here, but you mentioned in your original post that you expect the data store to be larger than 4 TB, however, looking at the extent you've added, it only amounts to slightly more than 3 to what you did...

    i.e.

    5 = 1.53 TO LUN

    6 = 1.53 TO LUN

    But LUN 7 does not seem to be 1.61 GB!  Is this right?

    Re comments made by RParker on button increase... It is only seen on the vSphere Client VI wersion, not on version 2.5, you use.

    Hops, it is logical, not sure if I got the wrong end of the stick here =)

    See you soon

    Adam

  • Windows 7 is not genuine, after the installation of windows 8 in dual boot.

    When I want to upgrade to windows 8, Windows 7, I think I should try windows 8.

    So, I installed windows 8 with dual boot.

    But after the successful Windows installation 8, when I started my laptop with windows 7 OS, it shows that the copy of windows is not genuine.

    What should I do?

    How can I get my windows 7 back as it was?

    Please help me... :'(

    Download and run the Microsoft Genuine Advantage Diagnostic Tool:
    Download the tool: http://go.microsoft.com/fwlink/?linkid=56062
    Post your results (copy button) and paste the results in your answer.

    As a starting point, the first thing you should check is the section to three figures on the number of product ID, if it corresponds or is included in one or two digits of the examples below, you have probably a MSDN or TechNet product key. "These keys must not be sold for retail use.

    065 066 067, 068, 069 to Ultimate, box 220 for professional and 230, 231, 232 area for Home Premium,

    There are probably others, but they should be close to those that are displayed"
    (How to be certain - download the Microsoft Genuine Advantage Diagnostic Tool listed above).

    Note: Though that illegally sold MSDN/TechNet allow product key for activation of more than one
    (usually 5 or 10), so these keys can be sold "several times" before activation may fail.

    J W Stuart: http://www.pagestart.com

  • Install windows 7 in Envy DV7-7234 with Windows 8 with win7 dual boot and windows 8

    I can install windows 7 in Envy DV7-7234 with Windows 8 buth with dual boot: win7 and windows 8?

    Installing Windows 7 on your HP ENVY computer Notebook dv7-7234nr is not supported by HP. In addition, no Windows 7 driver is listed on HP Software and Driver Downloads page for your computer.

    HP does not recommend installing Windows 7 and it will support the installation of Windows 7 on a computer comes with Windows 8. HP doesn't provide drivers for Windows 7 and the appropriate drivers are not available for the hardware in the computer. In addition, Windows 7 can not support some of the hardware or software designed for the computer.

    Make sure you create your media recovery HP or USB Flash Recovery discs before you edit or change anything.

    You will need to DISABLE 'Secure Boot' and ENABLE 'Legacy Support' in the ' settings of BIOS ' settings below page;

    Then, start Windows 8 and run the console 'disk management '. Using "Shrink Volume", reducing the size of the "C:" partition about half of its original size. Name of the partition "C:" to something like "Windows 8". Now, start the computer from the Windows 7 DVD, making sure to select "UEFI - internal CD/DVD" or "UEFI - ATAPI CD/DVD ' and not ' Legacy - CD/DVD internal."  (I recommend using a disc of Windows 7 SP1latest drivers have been included in this topic. The use of the SP1 disc usually resolves most disk hard AF and other issues. )

    Install Windows 7 on the partition without label that was established earlier when you shrunk the partition "C:". Continue to install WIndows 7 by / responding to all the guests. Once you download Windows 7 on your computer, we have to track down the compatible drivers for it. Please list all the "hardware ID" for unknown or missing devices.

    Please send Bravo

  • everything crashing when trying to install windows xp for a dual boot with preinstall windows 7

    I'm doing a dual boot with my preinstall windows 7, I'm done with partitioning already but when I try to reboot with my windows xp cd, just after he made all the check and talking about going to the installation of windows xp, it will crash and go to the Blue error screen. I was wondering how it will happen, so that I can install windows xp

    You first need to know if your computer is compatible with Windows XP. Much more modern computers are gradually support for Windows XP.

    How dual boot Windows 7 and Windows XP
    http://notebooks.com/2011/02/01/how-to-dual-boot-Windows-7-and-Windows-XP-Part-1/

    Another option is to run your license of Windows XP in a virtual machine on Windows 7. I have http://www.oracle.com/us/technologies/virtualization/oraclevm/061976.html

Maybe you are looking for

  • Equium drivers error

    Hello I have download the drivers for Toshiba Equium site Web from Toshiba form but when I bin unzip show - me error message. What to do now?

  • el capitan photo app

    I waited for the bugs 'off C.E"- what the 'Community' should say about the ease of use with the new photo app with the upgrade of the El Capitan? As well as... all remaining BUGS?

  • Update easy firmware Suggestions

    Something simple, Sandisk can do in the next firmware update to improve this Sport Clip (without too many problems): Easy: 1) to return to the song played instead of the Main Menu.  Treat the guys of circuit breaker; How in the world can people EQ th

  • No sound from HDMI output

    so I just plugged my laptop hp Pavilion in my LCD tv with a hdmi cable sounds and music can be played on the laptop when it is connected to the tv, but no sound on the tv at all. in my sound playback tabs, the device TICK is out HDMI NVIDIA. is there

  • If I change to ROME several times, performance is affected?

    I have a neo v.At first of all, I got GB and after I upgaded to ICS 4.0.3.because android of his questions I downgraded to Go on a sony service center.now update I'll test the 4.0.4 official and if I don't like it will downgrade to Go to a service ce