USB 20.0 M pixels 6 LED Webcam Web Cam does not?

Similar Questions

• How can I get my Crystal eye webcam icon, my web cam does not work.

  Please help me; to my 'sex cam Crystal eye' work. Thank you.

  Hello

  1. have you made changes on the computer recently?
  2. what happens when you try to use the webcam? You encounter any error message?
  3. what operating system is installed on your computer?

  I recommend you update the drivers for the webcam and then check out.
  http://us.Acer.com/AC/en/us/content/drivers

  Important note: This response contains a reference to third party World Wide Web site. Microsoft provides this information as a convenience to you. Microsoft does not control these sites and no has not tested any software or information found on these sites; Therefore, Microsoft cannot make any approach to quality, security or the ability of a software or information that are there. There are the dangers inherent in the use of any software found on the Internet, and Microsoft cautions you to make sure that you completely understand the risk before retrieving any software from the Internet.

  I hope this helps.

• my built in webcam used to work, but I think that one of my kids deleted something and now my web cam does not work what do I do

  my built in webcam does not work.i one of my kids deleted some how and now it does not work what do I do

  Hello

  Try doing a system restore. Go to the SEARCH bar and type system restore.
  Once the System Restore screen, select a restore point (it must be before the problem occurred), launch it. Check.
  You can also update the drivers of your computer (the webcam driver). If you do not know how to locate, you can use RadarSync to find out-of-date drivers.
  David

• Satellite T110-10 x - LED WAN wireless turn does not on

  Hi guys,.

  I have this model * T110-10 x * and I was wondering what should the front LED for Wireless WAN should be flashing or turning?
  It comes to the specifications of the model page:
  [http://eu.computers.toshiba-europe.com/innovation/product/Satellite-T110-10X/1076616/ | http://eu.computers.toshiba-europe.com/innovation/product/Satellite-T110-10X/1076616/]

  I bought the USB 3 G modem which works fine, but I was just curious to know if the laptop must have a built-in 3G modem, and if yes, what is the meaning of the key FN and the LED as this model does not have a built-in modem.

  Thank you.

  Hi mate

  Please take a look in the user manual which must be preinstalled on the laptop.
  There is information that the FN buttons in combination with the F1 - F12 keys would have enabled some features/options.
  The WAN/Wlan can also be switched on and off using the FN key!

  >.. .should forward for Wireless WAN LED should be flashing or rotating
  The LED must be lit and it not blink...

• C75-A-12 satellite - after Win8.1 update, 2 ports USB + cam does not

  I bought my computer in the MediaMarkt in Holland about 6 months ago.
  After updating Windows 8.1 don't work the USB 3.0 and USB 2.0 port on the right side of the computer.

  As my webcam, this one does not work too.

  I tried to install drivers, uninstall and restart, I tried Windows 7 installing the driver in compatibility mode... nothing works... I bought a Toshiba since I thought is was a reliable brand...

  Don't think,.

  What other van I do?

  François

  It seems that Satellite C75-A-12D PSCE2E 04804UGR was already pre-installed with the 64-bit Windows 8.1 System.

  I would recommend you to get the system to point in time early (before the MS updates was installed). In case this isn't possible, use the Toshiba HDD retrieve and set the operating system to factory settings.

  Then make sure that the webcam, but also two USB ports.
  In case everything would work properly, perform the updates of the system of Ms.

• Satellite A215 S4767 Chicony USB 2.0 camera does not work with Skype

  I have a Toshiba Satellite A215-S4767 with Vista Ultimate 32.
  I checked the drivers and they work, I have 10 Diretcx and it works.

  When I open the camera program, it works well.
  I put the camera program is not at initial start-up of laptop.
  I start the laptop, Skype open and figure that the camera does not work and say to check what I've done.

  Yesterday, I had installed the Skype 5.5.0.114 version and the camera has functioned well, I upgraded Skype version 5.5.0.117 and the camera started not to work.

  Hello

  > Yesterday I had installed version Skype 5.5.0.114 and the camera has functioned well, I upgraded Skype version 5.5.0.117 and the camera started not to work.

  This means that it is not software for laptop problem or a webcam, but maybe it s Skype related issue.
  You should check if the webcam has been chosen correctly in Skype video settings.

  If this does not work, uninstall the 5.5.0.117 version of the system, reboot the laptop, clean the registry using CCleaner (freeware tool) and then after reboot again to install the 5.5.0.117 again if not check the 5.5.0.114 a version that worked correctly in the past.

• One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it. The location is the root (2 ports) USB hub: 1-unknown device and Port 2-not used

  Original title: USB device not recognized

  Over the last 2 weeks, I get a message on a USB device.  The message said that one of the USB devices attached to this computer has malfunctioned and Windows does not recognize it.  The location is the root (2 ports) USB hub: 1-unknown device and 2-unused Port.  I have no idea what it means.  I hesitated to first click the icon (it does not last very long) thinking it could be a scam.  Can someone help me?  Thank you.

  Hello

  (1) is the specific question of specific USB devices?
  (2) did you of recent changes to the computer before the show?
  (3) have you tried plugging the USB stick on another computer?

  (4) what is the brand and model of the computer?

  I suggest to refer to the following methods and check if it helps to solve the problem.

  Method 1: Hardware devices do not work or are not detected in Windows

  Run Microsoft Fixit mentioned in the article.

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Method 2: USB Port may stop working after you remove or insert a USB device

  http://support.Microsoft.com/kb/817900

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 How to back up and restore the registry in Windows

  Reference:--

  Advanced troubleshooting tips for General USB for Windows XP problems: http://support.microsoft.com/kb/310575

• one of the usb devices attached to this computer has malfunctioned and windows does not recognize it

  I get the following message when I join my computr "one of the usb devices attached to this computer has malfunctioned and windows does not recognize," my nokia C3
  kindly help

  Most often when a device is not it's because of a driver.  Try reinstalling your.

  It works for win 7 & 8

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly? SignedIn = 1

  http://captaindbg.com/how-to-update-drivers-on-Windows-7/

• Error - "one of the usb devices attached to this computer has malfunctioned and windows does not recognize it

  Original title: USB device not recognized / dysfunction

  "Unrecognized USB device".
  One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it. Help for this problem, click this message. »

  This is what I get AFTER that I had to reinstall windows XP because a virus has attacked my computer a little before avg and Microsoft security essentials picked it up and destroyed... I have reinstalled twice... then I changed discs since I have two... well, I get this message from my 2 external Seagate Freeagent and my Phillips mp3 go gear aria... player these devices work on the laptop from my friend and she is under vista. It seems that since then they have worked on my computer before they would always run. My mouse and my cam work fine and my Canon printer gets thus detected... a few readers who have the space that is made... Ive looked everywhere for a solution... even upgraded windows media 11 and is player went to service pack 3. restarted several times... tried dPower Management tab and tried to

  Open recognition of the USB device by using Device Manager.

  .. I am at a loss: P please help thanks!

  isable the power management of the USB hub and I couldn't find the

  Hi LadyDefi,

  You can try to uninstall and reinstall the USB controllers and check:

  To remove and reinstall all USB controllers, follow these steps:

  a. Click Start, click Run, type sysdm.cpl in the Open box and then click OK.

  b. click on the Hardware tab.

  c. click the Device Manager button.

  d. expand Bus USB controllers.

  e. right click on each device under the Bus USB controllers node and then click on uninstall to remove them one at a time.

  f. restart the computer and reinstall the USB controllers.

  g. plug in the removable USB storage device and test to make sure that the problem is solved

  For more information, see the following article:

  Advanced troubleshooting tips for General USB for Windows XP problems

  http://support.Microsoft.com/kb/310575

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Error "one of the USB devices attached to this computer has malfunctioned and Windows does not recognize it." when you connect Logitech M225

  Original title:

  My wireless mouse works fine for the last 2 months, now, all of a sudden it doesn't work at all.

  I get a windows notification that says-

  "One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it."

  I have Vista 32 bit OS on my laptop.

  My office has Windows 7 32 bit and I am able to use the mouse on this computer, then the M225 is not defective.

  I tried to look for a download of update on the site of Logitech & only found:

  6.32.20 set - point it did nothing to help.

  I also tried to move the receiver to the other 2 ports USB w / still the same results.

  Are there other downloads or solutions that will help w / this problem?

  You can also try searching for devices strangers (with yellow symbols) in the Manager under the mouse devices and other pointing devices and other devices (if any). Right click and uninstall unknown devices. Then restart.

  Also try the steps below to reset the power of USB:
  (a) the laptop off, unplugged from the wall outlet.
  (b) remove the battery for a few minutes, then reinstall it.
  (c) then restart the laptop.

• USB device not recognized. -"peripheral USB attached to this computer has a malfunction and Windows does not recognize it."

  My phone displays a warning that a "peripheral USB attached to this computer has a malfunction and Windows does not recognize it." I uninstalled the only devices that I had (printer and bluetooth) but still this warning. Can anyone help.

  Mike S.

  I suggest to take a look at the following Web sites and follow their advice:

  http://support.Microsoft.com/kb/871233

  http://support.Microsoft.com/kb/310575

  http://support.Microsoft.com/kb/314464

• Windows 7 and install/recognize the problems of printer HP LaserJet P2015 error - USB Device not Recognized One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it.

  Title: Windows 7 and install/recognize printer HP LaserJet P2015 teething problems...

  I have a dell inspiron that was originally windows Vista and I changed to windows7.  I have a LaserJet where I work, a HP LaserJet P2015 printer and when I plug in the USB, it says (peripheral USB not Recognized One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it.

  How and what should I do to get the printer going or to get the computer to recognize.  Installation CD will not work and I looked online and downloaded drivers but still the same thing.

  Hi LOliver,

  Method 1: Run the hardware and peripheral troubleshooting tool and check if it makes a difference.

  Open the hardware and devices Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2: Disconnect all USB (Universal Serial Bus) devices connected to the computer (unless your mouse and keyboard). Connect the printer and check to see if the problem persists.

  Method 3: Connect the printer to a different USB port and check.

  Method 4: Reinstall the USB (Universal Serial Bus) controllers.

   First of all, please disconnect all USB devices and then perform the following steps:

  (a) click on 'Start', type device manager in the search bar and press "Enter." If necessary, click on continue.

  (b) in Device Manager, double-click to expand the "USB Bus controllers", right-click on the "host controller", click "Uninstall" and click "OK".

  (c) repeat step 2 to uninstall all items under 'USB Bus controllers'.

   

  Then, restart your computer and windows will automatically reinstall all USB controllers.

   

  HP printer drivers- ensure that you download the driver appropriate for your device model package.

   

  Thanks and greetings

  Ajay K

  Microsoft Answers Support Engineer
  ***************************************************************************
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error: One of the USB devices attached to this system has malfunctioned, and windows does not recognize it.

  tried already everything written here. When I plug my USB device (3 of them) my Windows a sad of the USB devices attached to this system has malfunctioned, and windows does not recognize it. I tried plugging it into another winXP machine, it won't work. Can you help me?

  Original title: usb malfunction

  His salvation,

  Thanks for posting your query in Microsoft Community Forum.

  1. What are the troubleshooting steps you have tried so far?
  2. If it works much earlier? If so, did you do changes on the computer before this problem?
  3. What type of USB device you are using?

  As you mentioned that the USB device does not work when plugged into a WinXP machine, it may be a problem with the device itself. In addition, the question may also arise if the currently loaded USB driver has become unstable or damaged or if your PC requires an update for problems that could conflict with a device USB and Windows.

  Therefore, I suggest you try the following methods (skip the ones that you already tried) and check if the problem persists.

  Method 1:

  Please try the fixit (s) provided below which will help you solve common problems associated with devices and USB ports.

  • Hardware devices do not work or are not detected in Windows
  • Diagnose and automatically fix the Windows USB problems

  If method 1 does not work, try Method 2.

  Method 2:

  Remove and reinstall all USB controllers.

  1. Open Manager devices by clicking the Start button, click Control Panel, click system and security, and then, under System, clicking Device Manager. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  2. In the list of the categories of equipment, locate and expand Bus USB controllers.
  3. Right-click every device under the Bus USB controllers node and then click Uninstall to remove them one at a time.
  4. Restart the computer and let the USB controllers get reinstalled.
  5. Plug in the removable USB device and test to make sure that the problem is solved.

  If the problem persists, go to method 3.

  Method 3:

  This method will install the latest drivers from device to your USB device.

  1. Click the Start button, type Windows Update in the search box, and then click Windows Update in the results pane.
  2. Click find updates. When the scan finished, click optional review updates.
  3. Click the check box next to the update, and then click install updates.
  4. If you are prompted, read the license agreement, then click I agree.
  5. Follow the instructions on the screen to download and install updates.
  6. If you are prompted, restart your computer.

  More information: Update a hardware driver that is not working properly

  If the device fails after updating the driver, you can try to roll back the driver with its previous version.

  Restore a driver with its previous version

  Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.

• "One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it." Why it does not recognize my device?

  Some time ago I had a huge problem with my computer (I think that my mother-in-law accidentally downloaded a virus) and I took it to a repair shop where they wiped out completely and replaced the hard drive.  Since I got it back when I try to use my wireless mouse and plug the nano receiver he said 'one of the USB devices attached to this computer has malfunctioned and Windows does not recognize it.  Why he says this?  And what can I do about it if anything?  I already tried uninstalling the driver and reinstalling, but that did not work because as soon as I plugged it it again once he says the same thing.  So I don't know what is happening or how to fix it.  Please help me!

  Hi Carla,.

  Please go to the Microsoft Community Forums.
  After the description of the question, I understand that you can not use the mouse on the computer wireless.
  Let me go ahead and help you to question
   
  What is the brand and model of the mouse?
   

  Here are some ways you can follow to resolve the problem:

  Method 1:
  Try to connect to other USB port and verify.
   
  Method 2:
  I suggest for the link and follow the steps in the article:
  Troubleshoot a wireless mouse that does not correctly
  http://support.Microsoft.com/kb/321122#appliesTo
   
  Method 3:
  Remove and reinstall all USB controllers
  Follow these steps:

  a. click Start, click run, type sysdm.cpl in the Open box and then click OK.

  b. click on the hardware tab.

  c. click the Device Manager button.

  d. expand Bus USB controllers.

  e. right click on each device under the Bus USB controllers node and then click Uninstall to remove them one at a time.

  f. restart the computer and reinstall the USB controllers.

  g. plug in the removable USB storage device and perform a test to ensure that the problem is solved.

  
  I hope this helps. If you have any other queries/issues related to Windows, write us and we will be happy to help you further.

• USB camera does not

  I have a 'VF0700 Creative LIVE! Cam Chat HD"USB camera that worked well in Mac OS X before my update to OS X El Capitan. It appears as a USB device in the 'system' report and I tried different usb ports and reset the SMC and be "zapped" the LANDAU.  No idea if this will be fixed in future update?  It's a standard UVC camera and it works with Skype and photo booth, etc. with the old OS X (I have a Mac Pro 3.1) and I can boot the old system and it works fine).

  librarian7 wrote:... it works with OSX... older...

  From your description, your device should work with 10.11.4.

  First, use Apple http://support.apple.com/kb/HT2090 to check the user-specific problems. You may simply move on to a user account that does not have the problem.

  (BTW - troubleshooting section called an "iSight" camera.  However, after that article was published, Apple has changed the name of the built-in camera on the recent "iSight" Macs "FaceTime", then "FaceTime HD."  Whatever the name of your built-in camera, the same info and troubleshooting applies.)

  To check the user-specific problems, you must test several Apple app (photo booth, FaceTime, iMovie, QuickTime Player, etc.) in more than one user account.  Do NOT use a 'Guest' for this test account.  If you have not already established a separate user, testing account, create one now.  If you need help, how is explained in http://support.apple.com/en-us/HT201754.

  A 'Standard' user account is all you need for the tests.

  If your camera will work properly with Apple in any OS X 10.11.4 applications user account, use OS X Recovery to reinstall completely your Mac OS X 10.11.4 System Recovery stored on your startup disk.  Don't bother test Skype or other 3rd party apps until you have your camera works with applications Apple.

  Post edited by: Jim EZ

  Mac OSX 10.11.4