USB device not found

Similar Questions

• I get device not found DPW on win XP for sony ericsson usb drivers

  I try to use my phone sonyericsson on my win xp pc and I get device not found MTP error message, even though I have mini usb as well as drrivers in my memory supplied with mobile phone card.

  Hello

  1. What is the model number for the phone?
  2. were you able to connect the phone to the computer with no problems before?

  Step 1: Try to run the fix it tool to the article below and check.
  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/mats/hardware_device_problems/

  Step 2: Check if the problem persists in the clean boot state.
  Reference: http://support.microsoft.com/kb/310353

  See also:
  Advanced troubleshooting tips for General USB for Windows XP problems
  http://support.Microsoft.com/kb/310575

• Bluetooth Lenovo S10e has stopped working - device not found / not recognized USB device.

  Hello

  For no reason that I know, installing bluetooth on my small S10e has stopped working.

  I noticed a few times when stop I had a "BTstackserver" does not message.

  I use the laptop to download regularly from a device compatible bluetooth.

  Today, when I go to connect, it says "bluetooth device not found".

  "Verify that your device bluetooth is properly connected and turned on".

  Hardware manual displays the config of LED and is correct, that if I press the "Fn" keys and "F5", I get the menu to turn on and off both the wireless and Bluetooth. I can turn on and off Bluetooth and wireless both with this menu option, BUT when I activate the bluetooth, I get the message 'one of the USB devices attached to the system is faulty or is not recognized.

  I deleted the Bluetooth installed and re-installed software by using the two bluetooth install files published on the list of drivers on lenovo S10e. Neither one works. I know that you need to install dir C:\DRIVERS once Setup has finished unpacking.

  I tried several other obvious things but without success. I also enabled "Bluetooth coopération" in the wireless LAN settings.

  All I can do now is get to the Bluetooth device under the keyboard cover and take a look at that? Anyone who has any suggestions until I get out the screwdriver? (The unit is out of warranty).

  

  I received my replacement bluetooth module and installing it, bluetooth is working again.

  I keep getting "BTW stack server" stopped responding when stopped down, but this does not seem to cause any problems.

  Too bad that original bluetooth module did not survive barely a month after the end of warranty date...

  I'm used to a greater reliability of Lenovo.

• Device not found Airport Extreme

  We have an airport extreme connected generation via Ethernet to a switch that provides network access to our entire House (about 10-15 connections) via wifi access points all Ethernet hard wired (linksys + apple) and a direct wire to a PC. Airport extreme is the dhcp and is connected to a gpon fiber using PPPoE.

  The problem now is that the AirPort Extreme disappears from the airport on iOS Mac utility and Windows, it is found however the network and the Internet continues to operate normally on all connected devices. I can also continue ping on the router.

  I have reset the AirPort Extreme to the default settings, but the problem continued...

  I tried to unplug all devices and have AirPort Extreme only connected to him have the fiber but the problem persists...

  no idea how I can fix this problem?

  You describe a known problem with Back to My Mac which first appeared around July 13. The problem manifests itself in a message "Device not found" meant to be displayed in triangular AirPort your AirPort base station with a yellow icon utility, while the router of the device functions others continue to work normally.

  If you use an airport Time Capsule, backups will not work using that device or USB hard drive units connected to it.

  Apple will only be able to solve this problem, so all you can do is wait for them to do. If you want to contact them to tell them about it, using the contact Support link.

  There is a solution: on a Mac, open AirPort Utility and select file > configure other...

  For each of your routers Apple AirPort Base Stations serving their respective networks: its IP address and password (if you don't know either of them, read the Note that follows the horizontal rule below). Then, on the tab of the Basic Station , delete all the entries in the Back to My Mac using the 'negative' button, then click on Update.

  Which must be re-established appearance of this base station in AirPort Utility, as well as in a side bar of the Finder, if all shared disks are plugged on. It will also restore possibility of Time Machine to save on these discs, if this has also been a problem for you.

  If this seems to imply that you will not be able to use Back to My Mac until Apple fixes it, you are probably right. Well to diagnose problems of the CCMM is tedious work that I have not yet finished.

  Apple does not participate on this site except in a very limited way, so don't expect is not a response from them, here or elsewhere for that matter. We'll just have to wait for them to fix it.

• Office jet 4500 G510-g, the imaging device not found

  I have an Officejet 4500 with a wired Ethernet connection. For some reason any, that my computer has ceased to be able to scan from it, I can still print and everything very well. I don't remember to make changes to the system and other computers on the network can always analyze without any problem. I restarted my computer, unplug the printer, uninstalled and reinstalled the software, active windows firewall settings and cannot find any reason why it won't work. I am running Windows 7 64-bit on the computer that does not work, the other computers on my network that still work are running windows 7 64 bit and XP. On the "HP Imaging device not found" error message that opens under more information, I get this: 8 [(1, 0,-2147221496)]

  I've lived the HPSDU and he said: there is a problem with the driver and he cannot communicate with the product. He said also it is impossible to scan with windows WIA, and finally it's the Twain component may be damaged. I have uninstalled, reinstalled, re-downloaded the Installer off the HP site several times, but can not solve this problem. Help, please.

  Hi crakerb,

  When you click on the plus sign on the error message is that all of the information it provides?

  Because you can not install the printer using the USB connection, it seems to have some problems with the operating system on this computer. Did you back up your data and perform a full system recovery?

• 3480CT, device not found driver Portege

  I have a problem,
  I have a laptop toshiba portege 3480CT and is not an operating system. I am trying to install win98 SE, but when it starts to install this message appears:
  device not found driver: "OEMCD001."
  Invalid device CDROM drivers selected

  : so, how can I get these drivers, the computer has only CD-ROM drive, FLOPPY No.. CDrom drive is a pcmcia drive.
  Please help me!
  :)
  I also tried to install XP pro but with bad results, it gives errors when it tries to start the windows installation...

  WHAT to do, any help much appreciated!
  Thank you

  Hello

  If you have installed WIN 98SE on the device you need Toshiba drivers and utilities.
  Win 98SE OS you install all the applications in the following order:

  Display drivers for Windows 95 (for S3M7 Savage MX/IX) V4.11.01.7006 - 7.02.88 - 01
  YAMAHA AC - XG Audio Driver for Windows 95/98SE V.4.07.1011
  Floppy disk Win98 companion W98C09
  Logitech MouseWare for Windows 95/98 V8.37 BLD246
  V5.77 - MR577ALL004 modem driver
  Driver for TEAC V.1.06t (FDD Version 1.08 t) USB floppy drive
  Driver drive disk USB for YE - DATA V.4.30 Beta
  Panning of Driver Support (panning.sys) V3.0 (included in the display driver)
  Multi Media Port Replicator IDE Driver V.1.1.2.0315 with the file catalog
  Driver NDIS for V.2.21 de MSIR3.0 (driver Win98 OBOE)
  Toshiba Fast Ether LAN adapter (Intel 82559) V.2.01
  HALLOC. EXE (included in the Toshiba utility) V2.0
  Toshiba W983480US utility
  PCMCIA. INF for Windows98SE (support ToPIC100) V1.0
  QFE Win98Gold/Win98SE QFE KB:Q239697
  QFE Shutdown QFE Q242934
  QFE DiskTsd.VXD V.4.10.2223 Q246387xx8
  NDIS QFE Q243199 QFE
  QFE Win98SE USB QFE Q241084
  Direct X 7.0
  Acrobat Reader
  The users manual PDF file
  File PDF Manuel Modem internal
  Multi Media Port Replicator manual PDF file
  Toshiba wallpaper
  MS URL security update

  For Windows 2000 / XP in this order:

  Display driver
  TVALD
  TOSHIBA Power 2 extensions
  Toshiba Utilities
  Toshiba Mobile Extensions
  Energy saving of Toshiba Display Driver
  Toshiba infrared driver
  Toshiba IDE driver
  Acrobat Reader 4.05
  Operating instructions online
  Online modem manual
  Online manual users to multimedia Port Replicator
  Audio driver
  Driver Modem
  Country select utility (included with driver modem)
  Copy Toshiba wallpaper in c:\winnt
  Apply Service Pack 1 for the system
  Activate "Show the components of the" unplug or eject hardware trayicon
  Reinstall the display driver to support the new graphik S3 chip

  All the drivers you can find on the Toshiba site:
  http://EU.computers.Toshiba-Europe.com/
  Please let me know if it has been successfully

  Best regards

• Pro 608: HP 608 Pro will not boot-Boot device not found

  I got my new Pro 608 and installed my software after upgrade to Windows 10. Do okay, but the next day, nothing works!

  Keep saying that Boot Device not found!

  Not sure but it could be HP shield encryption does not work well? now, he cannot read the HD? or HD shot?

  I tried to restore default - but still does not work. Now other bios diagnostics no longer work. That is to say he's corrupt!

  Tried to update the bios, but doesn't seem to work. The bios still say 7/2015. I tried to update the bios 9/2015. Also used 7/2015 bios, bios Diagnostics but still does not.  I use a USB port and a connector USB Belkin C - I think not that it really is booting from the USB key to install the Bios.  I set the Bios to activate the firmware-C update.

  Sue, the best thing you can do since it is a new Tablet is contact HP Support directly for warranty repair.

  Most likely, they will replace the unit.

  Contact HP worldwide | HP® official site

• 15 15 HP - r208nl: start the device not found error (3FO)

  Hello

  I have this laptop from less-than-one-year-old (this guy: http://icecat.us/us/p/hp/l0n16ea/laptops-0889296492238-15-r208nl-26524145.html) and I have the Boot Device not found error infamous.

  I'm not sure if this is relevant, but the problem occurred a few weeks after the upgrade to Windows 10 (when bought, laptop had Windows 8.1, probably an update of Windows 7).

  Also, I noticed this basic operation to during the priming phase take a long time. For example, when I press F10, it takes about 1-2 minutes to bring up the BIOS configuration screen.

  There are a number of similar questions on this forum, but the proposed solutions do not apply to my case or simply do not work. Here's what I've tried so far, without success:

  • hard reset
  • reinstalling the hard drive
  • automated tools in the Recovery Manager (this tool you access by pressing F11 at startup) *.
  • chkdsk and identical from the command prompt (to which I have access from the Recovery Manager tool) *.

  Note that even if the material for the HP PC Diagnostics tool failed hard drive test, apparently I can access my files on the hard drive of a Linux Live CD/USB (I managed to access it during a previous attempt, do not know if it can be reproduced).

  I can't test the drive on other PCs (which I have another laptop which I can plug the drive may be defective), not I can try to connect another hard drive non-offending for verification (as I did not).

  Any suggestion?

  They gave me no installation CD/DVD (I guess I had to use the recovery partition). In case I need a new installation, how can I retrieve my serial number?

  the hard drive is not accessible, I can't access Recovery Manager simply by pressing F11, I had to use a USB recovery media

  CHKDSK and even produce this error message: "cannot open volume for direct access.

  It looks like your hard drive is not/is a failure. Guarantee would provide a new replacement - and probably send recovery media free since did you not make it yours.

  You can make a Windows 10 usb or dvd using the free download of Ms. No license key is necessary since it has been activated at the same time on the machine.

  https://www.Microsoft.com/en-us/software-download/Windows10/

  Read the guide here by reinstalling an previously active Windows 10:

  http://www.howtogeek.com/224342/how-to-clean-install-Windows-10/

• 15 - p030nr: Boot Device not found

  Need help on how to fix a problem where it says "boot device not found." He worked to find one day and the next time I turned on the computer, she appeared with this error message. After reading some things, it seems that it is a right of common mistake around the 1 year mark, but I don't know which is correct. Are there methods I could do to fix this problem.

  OK, if it was an old PC, my guess would be that the hard drive is a failure, but on a PC old of a few months, it is unlikely.

  However, it would be interesting to follow these instructions to check the hard drive:

  Presume withdraw OK, what might work is booting from CD or USB and running CHKDSK to see if this helps to repair the file system.

  CHKDSK is the short name of a utility that provides MS that will do a check of the file system and attempt to repair problems.  A damaged file system may prevent your computer to start correctly and get to a Windows desktop.
  
  Because you can not boot from your PC, then you need to download one of the following options and follow the instructions it contains to make a bootable USB stick or a CD:
  (1) miniTool Partition Wizard
  (2) EASEUS Partition Master
  (3) assistant Partition AOEMI
  
  Once the media, boot from it and use the option to check the disk.

  Good luck
  
  I'm a volunteer and I do not work for, or represent, HP.
  ========================================================================
  If you feel that my suggestions helped you, please click on the thumbs-up symbol to say thank you!
  
  If they helped to solve your problem, please click 'Accept as Solution' to help others find similar information.

• G2 HP 450: blutooth device not found

  I have trid to install blutooth device driver. When I click in the software, it has begun to install but after sometimes it shows this blutooth device not found. I hardly remember that maybe I uninstall the blutooth Device Manager device. What can I do now? Help, please

  Hello

  Looks like your machine is ONLY the second option on my first response, which means that your machine has NOT of Bluetooth. If you wish, you can buy the USB Bluetooth dongle for about 15 euros.

  Kind regards.

• How do I update driver for printer Epson Stylus C43 Color inkjet (USB device not recognized)

  I run Windows XP Home Edition and have a printer Epson Stylus C43UX Color.  Quite often, the printer connects, is recognized by my laptop and works very well, but sometimes, when I connect and turn on the printer, I get a ball on the toolbar "USB device not recognized" State the Device Manager shows the printer as an unknown device and in the State of the device properties is no indication 'no driver installed for this device.  I uninstalled drivers and enforcement "Looking for new hardware" menu Action of the Device Manager has received the balloon message "new hardware found: your hardware is installed and ready to use. Try to then print the results in a "Communication error" message and the printer fails to print.

  Hello

  
  You did changes to the computer before the show?

  Method 1:
  Try the steps in the link and check.
  Advanced troubleshooting tips for General USB for Windows XP problems
  http://support.Microsoft.com/kb/310575

  Method 2:
  You can update the drivers on the manufacturer's Web site and check.
  See the link to update the driver:
  How to manage devices in Windows XP
  http://support.Microsoft.com/kb/283658
  Manufacturer link:
  http://www.Epson.com/cgi-bin/store/support/SupportIndex.jsp?BV_UseBVCookie=Yes

  Method 3:
  Try the steps from the link and check if you are able to print.
  Printer in Windows problems
  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

• 5520e "Device not found" firmware update

  Product: HP Photosmart 5520e printer all in one.  Check the hard drive, and driver seems to be: Photosmart-5520-series_v12 - 2.23.0.dmg, which I believe is the most recent.

  Problem: The firmware is not updated?  Happens in this way while troubleshooting problem try to scan.  I remember correctly, the error message with the sweeping question was a communication problem that was confusing because the printer and the computer communicate very well via USB for printing purposes.  Since turned off direct wireless and use the router and can now scan the documents.

  Using an iMac running 10.6.8 that is physically connected to the printer via a USB cable, and now also via a wireless router.  Am able to print and scan documents.

  Downloaded the latest firmware on computer.  When you try to do the firmware update got error message: device devices not found no. requiring an update of the firmware could be found.  If you think that there is an error, make sure that your device is turned on and properly connected.  -What is this error message telling me that it cannot find the printer, OR, it tells me that the firmware is up to date.  Latest firmware date of 2014-03-28.  I probably can't do an update in the last 6 weeks.  Is there a way to check to see what firmware currently installed?

  Thank you.

  Hello

  Need to print a Page of State printer to determine the version of the Firmware that is currently on the printer.

  Try the steps below to print "printer status Page.

  > touch SETUP (wrench), then

  > Touch TOOLS, then

  > touch PRINTER STATUS REPORT

  The current version of the firmware available is MGP5CN1351AR.

• HP Deskjet 3054: Printer works but not the Scanner (device not found)

  Configuration: Windows 8 Lap Top with a HP Deskjet 3054 directly connected via USB

  Printer - it works

  Scanner - when you run the Application "Hp Scan and capture ' it comes back and says"device not found ".

  I tried - I ran 'HP print and scan doctor '.   Everything is OK except the "HP Scan".  He said that it was not able to find the HP Scan software on my computer.   When I went on HP customer support site to download it, I couldn't find it.  There is nothing that I could see which says "HP scanning software".   So this software HP Deskjet full functionality and drivers what I should download and install?

  BTW, the "HP Scan and Capture" application allows to work perfectly.  Not sure why it isn't now.

  Hello

  When changed the type of network to a USB connection? scanning HP and Capture app support network scanners, it does support a USB connected device:

  http://support.HP.com/us-en/document/c03478505

  In the HP Deskjet 3050 software select scan a Document or Photo and check if this can work...

  If the same persists, unplug the USB, uninstall the HP Deskjet 3050 basic software drivers from programs and features, then download and reinstall the most comprehensive software features again.

  If you prefer to continue to use the HP Scan application capture &, open the HP Deskjet 3050 software, click the utilities tab, click the printer installation software & and select Convert USB wireless to connect the printer to your network. then the Scan & Capture app should detect the scanner.

  Shlomi

• I deleted by mistake com6 usb modem com port, now when I troubleshoot it shows no modem usb driver not found.

  I deleted by mistake com6 usb modem com port, now when I troubleshoot it shows no modem usb driver not found.

  Usually, by unplugging the USB device and plug it in then that she return to should force Windows redo the settings.

• Touch screen does not work and the message "USB device not recognized".

  I have a Samsung Ativ book 9 Lite. Everything works fine until that recently when my touch screen stopped working (is there a function button that could possibly have it?) and I constantly get a notification from Windows Explorer that says "Device not found USB." When I go to the Device Manager page it constantly keeps refreshing, so you can't click on almost any. There is an element that shows as unknown, but if I try to uninstall or disable, it happens immediately. I just downloaded the latest driver for the printer I only use and still no luck.

  Any help?

  Hey Jake,

  I suggest to download the latest driver available for the touch screen on the manufacturer's Web site and install it.

  Install the latest drivers

  http://Windows.Microsoft.com/en-us/Windows-8/all-drivers

  Also try to update the drivers for the chipset of your PC and check if it helps.

  Let us know the results.