USB does not not on my HP DM4-1265DX

Recently, I had my motherboard replaced by Geek Squad to the laptop and now my USB does not work

The two 2.0 do not work with any Plug that I put in my 3.0 only works with any type of USB. I tried to uninstall and updated the driver, updating the BIOS, check if the port was clean, reinstall Window (which was a pain waiting), reset the CMOS, reset the default Bios and see that I can't access the menu in Advance on my HP Pavilion dm4 because it doesn't have this option to unlock. Thanks in advance!

Hello

You did most of the troubleshooting of your end steps steps only takes a few steps are updated Bios and recovery. If you still have the same problem as you informed that Mottherboard has been replaced you must bring it to the Geek squad and have it checked could be the cause of the motherboard.

Tags: Notebooks

Similar Questions

  • HP Pavilion dm4-1265dx: does not update HP Pavilion dm4-1265dx

    Pavilion dm4-1265dx has never successfully updated its software. I run the recommended updates that are included in my automatic Windows updates, but not the HP updates have already updated, it always says, "failed." I tried to update directly from the HP site and have experienced the same results. Any suggestions?

    Hello

    Thanks for posting your concern for the Forums for Support and sorry about the problem you are having. To help you the best I would need the failure error code. I will quote the steps to get the code of failure below.

    • Go to the Control Panel
    • Make sure that in the upper right corner of the ' view by ' is selected for both small or large icons instead of the category.
    • Go to "Windows update".
    • You will find on the left in the list 'view update history'.
    • In the list, the status of the various updates would b mentioned in the second column.
    • There will be updates failed, you need to right-click on it and click 'see details'.
    • On the next window, there will be "Error Details" section with code 8xxxxxxxx.

     

    These are the codes that are required. Please write us back with these codes. And also for resolved errors you can try to install the updates individually.

    • You have to go back to the control panel > windows updates.
    • In the list on the left choose "check for updates".
    • Once the updates is enabled, it will be little important and a few optional updates.
    • First click on the important updates and a list would be populated, choose the updates one by one.
    • After an update is installed and the le redemarrage reboot the PC, choose the second update and continue in the same manner.

    Although I work for HP, but I am personally.

    Please click "Accept as Solution" If you feel my post solved your problem, it will help others find the solution. Click on the 'Bravo Thumbs Up' on the left to say 'Thank you' for helping!

    Concerning

    Aks3621

  • Satellite Pro 460CDX USB does not

    I Sat Pro 460cdx with w2000 but my dose usb does not work. In Device Manager the port appear as unsupported nec pci to usb open host controller.

    And the port is not a driver?

    Any idea?

    Hello

    AFAIK This oldie is supported for the Windows 95 operating system. Have you had the same problem using Windows 95?

  • my super USB does not work after last update OS EL Capitan

    my super USB does not work after last update os el capitan

    Hi viral_02,

    The resources below provides a few for the SuperDrive USB troubleshooting steps.  Click on the link to see all the possible symptoms and solutions, including resetting the system management controller.

    Get help with the SuperDrive slot on your Mac computer loading

    If the problem persists, Contact Apple or an provider of services authorized Apple, or make an appointment with an Apple Retail Store additional diagnosis, evaluation, or service.

    Take care

  • I installed Windows XP on my new computer (with Windows 7 PRO), but my USB does not work on Windows XP. It works fine on Windows 7

    I installed Windows XP on my new computer (with Windows 7 PRO), but my USB does not work on Windows XP. It works fine on Windows 7.

    Hello

    And much more: (XP mode requires professional, Ultimate or Enterprise).

    Get all the benefits of Windows 7 and continue to take advantage of your investments and more
    business and productivity programs that require a PC running Windows XP.

    Note: Windows XP Mode requires a download.
    http://www.Microsoft.com/Windows/Windows-7/features/Windows-XP-mode.aspx

    Windows XP mode
    http://www.Microsoft.com/Windows/Virtual-PC/Download.aspx

    Windows XP Mode is supported through Technet

    TechNet - Forums - Windows 7 virtualization
    http://social.technet.Microsoft.com/forums/en/w7itprovirt/threads

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

  • "USB does not recognize the device.

    After four years of working perfectly, my Acer Aspire with Windows Vista Home Premium has suddenly decided to generate warnings "USB does not recognize devices" for all external references except a network controller Linksys that needs to be changed around the ports to operate and has constant warnings "that works better on a 2.0 port." Advice please, very confusing Norfolk UK.

    See if it helps:

    "USB device not recognized" error keeps popping up and USB devices do not work
    http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-hardware/USB-device-not-recognized-error-keeps-popping-up/6be4581d-8fbd-407F-815E-b475c35ca586

  • USB does not fit in the printer

    Have a deskjet 1050a and USB does not fit into the printer.  Help

    Thanks I found one.  Printer downloaded and everything got set up.  (except that it took me 2 days to do it).

  • Toshiba still 8 Micro USB does not, does not charge

    I have installed Nokia PC Suite on my Toshiba Encore 8 tablet and connected my laptop Nokia C1 via micro-USB on my tablet.

    Since then, my Toshiba still doesn't recognize not the USB port, two usb devices or, more important, for the load.

    My tablet is now only 8% load, and I need to get the USB charge function working again while I have still a few charges left in the tablet to make the necessary changes (drivers, BIOS etc.)

    Can anyone help before my Tablet becomes a brick died without charge to the left?

    Hello

    Looks like we have a similar problem, although I have a different tablet model (AT10-A) and I did not install anything whatsoever... still, I'm having the same issue on the micro-USB port: it does not recognize the Chargers and USB connections with my laptop. To the point where it says 5% battery. I'll try to keep it connected to the charger, even if the Tablet does not seem to see it.

    How can I test if the battery is really in charge?

    Have you received support from Toshiba?

    Thanks and best,
    Luca

  • Satellite Pro 4270 - USB does not work

    Hello.

    I had this problem for a while, and I was wondering if anyone had any suggestions to solve this problem.

    I have more or less of work Satellite Pro 4270 (4200 Series) computer laptop with XP on it.

    The USB port does not work. I don't know why it does not work. I tried to replace the USB module on the motherboard that has not worked. I've updated the BIOS to the latest version, has not functioned. Removed and reinstalled the drivers in XP, not worked. I'm out of ideas.

    IrDA works very well.

    Some suggestions please. Thank you

    Hello!

    I understand, were you solder the module USB motherboard and then solder another module?

    I mean, what have you done with the module USB, replacing? Sorry, I don't remember exactly how the USB module is connected to my mobo SP4270 seen last about the half a year ago... If the welding, I don't wonder the problem... but if not, there may be a solution...

    Best regards

    Pete v.

  • HP 260 G2: USB does not work with W7 x 64 installation ENT

    I have a new G2 of 260 HP, when I proceed to the installation of W7 x 64 USB business, after th e first loading, USB devices does not work. I tried with the utility of th 'Installer_Creator' from Intel, but with the same result.

    You can someone help me with this issue?

    Thanks in advance

    Mauro Caputo

    Hello:

    You must run this utility...

    https://Downloadcenter.Intel.com/download/25476/Windows-7-USB-3-0-creator-utility

    Your only other option would be to use a PS/2 keyboard and mouse to complete the installation and then install the drivers for Chipset and USB3 you need.

    or see this post for an alternative solution.

    http://h30434.www3.HP.com/T5/business-PCs-workstations-and-point-of-sale-systems/HP-prodesk-600-G2/m-p/5485092#M11107

  • Re: Satellite C660 - One USB does not work

    Hello

    As the title says, I have a c660 that has only a working USB port. The other is dead and has been dead since day 1.

    I tried to uninstall the USB controllers, re-boot and allowing the automatic hardwarediscovery run and install again. This has not solved the problem unfortunately.

    I am running windows 7 by the way.

    Another had a similar problem or has any ideas?

    Thank you

    TFM

    If only a single USB port does not work and if the other is OK then I think it is a dysfunction of the USB port and not related to any software.

    So in this case, I think you should visit the ASP from Toshiba for a verification of the motherboard.
    The USB ports are part of the motherboard and possibly you need new mobo.

  • SSD external via USB does not start by default

    Hello Apple community.

    I have a problem with my new external SSD. Given that the base model Mac Mini end of 2014 comes with a disk HARD 5400 RPM drive, I wanted to go to an SSD without having to tear the whole unit. I wanted to exhaust the option 'boot from USB' and I'm having a strange problem. I cloned my Mac to the new drive SSD and slapped in a box set of the speaker. I connected via USB and changed my 'startup disk' to use the external SSD drive. However, it does not start on this unit automatically. When I reboot and discovers the "boot manager" I see the USB being initialized automatically. After disconnection / re - plug the drive in, it appears as a boot option. Once it is initialized, everything works fine and I can boot into El Capitan without any problem using the SSD.

    I am trying to find a way that I can get the Mac to initialize the SSD to the boot upward and choose default. I don't want to have to re - connect the drive whenever I want to start on the SSD drive... Any help and suggestions are greatly appreciated!

    My equipment

    ===========================

    Model Base of Mac Mini (end of 2014)

    1.4 GHz Intel Core i5

    4 GB of DDR3 1600 Mhz

    OS X - El Capitan v 10.11.3

    240 GB SanDisk SSD more - connected via USB3.0

    What unit do you use for the SSD?

    Can you provide a link?

    If the SSD is delivered with a box to provide a link to that,

    How do clone you for the SSD? What app did you use?

    -Try to reset memory NVRAM/PRAM and SMC

    MacIntel: Reset of the controller (SMC) system management

    Subject of memory NVRAM and PRAM

    -Try to start safe mode

    OS x: what is Safe Boot, Safe Mode?

    -Start to recovery and repair the startup disk

    OS X: on OS X Recovery - Apple Support

    -If it is repairable, reinstall the OSX. Nothing shall be lost

    How to reinstall OS X on your Mac - Apple Support

    -If you do not have a backup using disk utility to restore the internal drive to an external drive, so that you can try to recover the data.

    Format the boot disk and then do a fresh install of Mac OS x

  • USB does not work on Satellite A110-294

    Hello

    I must first apologize because my English is not perfect, so I'll use simple words.

    A friend has a problem with its ports USB on a Satellite A110-294. I try to solve the problem, but without success until yet.
    I did a fresh install of windows XP with the toshiba installation CD, but it does not solve the problem. Then I try to remove usb devices in system properties, but there is a problem when I try to remove the usb host controller. System freez and nothing works no more! I remove hub root, but it works.

    I try to download some difficulty for usb with SP2 problems, but the prob still here. I saw there are some updates to INF files for some chipset intel but it is impossible to find the update intel celeron chipset. Update the BIOS to 1.70 and no result.

    I try to look for some drivers for the motherboard of toshiba but I can't find anything.

    What can I do to fix this?

    Satellite A110-294 belongs to the series of PSAB6E.

    On the Toshiba site, you won't find a chipset driver because it s built into the display driver for this model (chipset). You don't need a driver chipset Intel, this laptop has an ATI graphics chip and chipset.

    Then try to update the display driver:
    http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  • HP Probook G3 450: USB does not work

    I formatted my hard drive and installed windows 7.

    None of the usb drives to work. It is common in the sub player but nothing appears in Windows Explorer, when I plug in a flash drive. When I plug in a mouse, it does not work.

    It is a platform of Skylake has no USB 2.0 driver for Windows 7 does not work. You must install the USB 3.0 driver and probably a lot of other drivers, as well.

    http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=7834518 & swItemId = ob_163291_1 & swEnvOid = 4060

    There is a whole page of WIndows 7 supported for this model.

    http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=7834518 & lang = to & CC = US #Z7_3054ICK0KGTE30AQO5O3KA30B3

    Make sure that the drop-down menu to select the operating system is set to Windows 7. I assume that you have installed the 64 bit version.

    If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

  • Satellite Pro 6100: peripheral USB does not

    Can anyone help me please with the following problem.

    Satellite pro SP6100:
    After the computer starts, I get the error message USB device does not work correctly.
    I have nothing plugged into the USB port but I don't get the error message.

    Is there anyone with any problem and does anyone know a solution?

    Hello

    How rachelrising said it, it s a good idea to remove the device from Device Manager.
    After the reboot, the operating system should recognize the device again.

    Best regards

Maybe you are looking for

  • I can shrink iMessage received images display?

    Can I reduce the size of the new photos of iMessage on my screen? I think they're called stickers. Their biggness and their lively movement that bothers me. I would like to block them entirely without blocking text even if it is possible. Animation o

  • Reinstall Leopard after the white screen?

    I have an iMac that came with Tiger. He upgraded to Snow Leopard and Lion. Today it froze with the rotation of death beach ball. Off with the power button, it starts. That he is a white screen, no edge start-up, no logo. also, one or two attempts res

  • Problem in Labview DSP

    I have a DSP problem to be realized in the labview. However, I am not very familiar with a few boxes to tools. The goal is to detact the pulse whose duration and intensity of a noisy signal in real time. Given the pulse signal, the points how to loca

  • Windows software update 7.0.6000.381 failed error code 8024D00F

    where can I find this download yet once (it is not in my hidden updates) so I can try to download and install this update inportant please

  • can't mfcans32.d11 folder,

    you spot a copy of load to the bottom of the file: mfcans32.d11