USB keys are no longer automatically install

Similar Questions

• Dell: inspiron 1525 not boot from a USB stick, USB key are not not in the start option.

  Hi all

  I bought this dell laptop inspiron 1525 in the year 2008 with mentioned configuration:

  Core 2 duo processor

  1 GB OF RAM

  Due to some problems in my windows vista, I decided to install a new windows vista in my laptop. I run the dell support live cd at the start of my laptop and created the partitions on my system. But while the new installation OS on the cd i found that optical drive of my system does not work very well. so, I decided to install the new OS of USB. I went to the BIOS and selected the USB key in the boot sequence. but when I tried to install the new OS while pressing the F12 key, USB key is not listed in the start option.

  could someone help me to install the new OS in my machine? It is very urgent that my machine is down for 1 week.

  Please try attached BIOS changes screenshot than everything be useful to me.

  Thank you

  Gurpreet

  Hi Gurpreet,

  Thank you for your response.

  My apologies if I seem repetitive, but when you go to the Option of boot sequence in the system configuration screen, do you think that the USB storage device listed? And do you see a number in front of it?

  Go to the option for embedded devices and check if the USB ports are enabled or disabled. If disabled, change the option and enable the USB Ports.

  If this step does not help, go to the Maintenance option in the system configuration screen and press enter on 'Load Defaults'. On the side right, highlight 'Continue' in green, press Enter and then save & exit.

  Please keep us informed of the results.

  Thank you and best regards,
  Babita S
  #iworkforDell

  For easy access to the drivers, manuals and updates, please visit our Support Site .

• HP Pavilion g6: My USB ports are no longer works. Can anyone share their expertise?

  I'm going to design mananger and it shows a yellow typical mark next to the universal serial bus. I tried to update the driver but there no driver not installed.

  Hello, I have restart my PC and restore it to its original from the manufacturer. I lost everything on my computer, but it's ok now, my USB ports are working properly. Thank you for your help.

• USB key are not displayed

  My VM is running Windows7 and none of my USB key appear. How can I make them appear in Windows Explorer?

  First of all, make sure that your host can see, follow these steps in your VM Workstation:

  In the attached photo, this is an example of my external hard drive, all you have to do is click on Connect (disconnect the host) and you should be able to access it from inside your virtual machine. In case there is problem and this can be done, you can still use shared between the host and the VM folders

• Some files in my USB SanDisk 16 GB USB key are not detected and when I connect to another PC, all files are detected

  Original title: some files in my USB are not detected and the rest of the files show find when I connect to my pc, when I connect to another pc the files seems to find.

  Hello world

  I have a SanDisk USB 16 G with important files, when I connect to my pc windows 7, some files are discovered, I am able to read other files show as empty files and my pc don't its not able to open them.

  When I connect the same USB for my lap top with windows 8 all the files where to find and I can open with a problem.

  Can some body please help me solve this problem?

  Hi Martin,

  This problem can be caused if the program for the particular file could not be installed on your computer.

  1. What is the file format or the extension of the files that you do not read or recognize in Windows 7?

  2. what exactly happens when you try to open empty files?

  3. have you made any recent hardware or exchange of software on your computer before the show?

  You need to check the files that are not open in Windows 7 and trying to install the software for files that are not opening and control.

  Let us know the status of the issue. If you need help, please after return. We will be happy to help you.

• Satellite C660 - USB keys are not mounted

  I have a * Satellite C660 with Windows 7 64 bit *. When I conect a USB stick (2 GB LG or other), Windows install the new USB, but after a few seconds, the USB is disassemble and assemble and disassemble some indefinitely.

  With my old * Toshiba Satellite M50, Windows XP * both sticks work very well.

  Hi mkobets,

  Probably something wrong with USB ports or driver chipset so the glue work with your old Toshiba laptop USB

  Means the simplest would update the chipset in my view driver that you can download here:
  http://EU.computers.Toshiba-Europe.com/innovation/download_drivers_bios.jsp

• When I activate my machine in stand by mode all USB keys are non-functional, unless I have re-boot or sign out and sign back in. Any ideas of the problem and fixing it?

  The machine is HP nc6400

  Hello

  · What is the service pack installed on the computer?

  · Will there be any changes made on the computer before the show?

  Follow the steps in the link below and check if this may help: how to solve the problems of hibernation and standby in Windows XP: http://support.microsoft.com/kb/907477

  See also: peripheral USB is not recognized when you attach it immediately after that your Windows XP computer comes out of standby or hibernation: http://support.microsoft.com/kb/871233

• MU USB ports are no longer works?

  I hope I have this in the correct category to help!

  I have a HP Pavilion dv9000.

  Until about a month ago my USB ports worked well. Now, they only charge my iPhone and work my wireless mouse. They do not read my external drives, as they did, as I have lots of info on these drives should I go for info.

  I have used my drives in another computer and they read it very well, it's not the drive itself.

  I tried to install a PCIMIA card with no luck. On this map, I even used the additional power source that will map to an adjacent USB port for power and not luck.

  Is there a way to solve this problem or a work around? Or is the computer to a point of electronic recycling?

  Thx for any help that you can float my way.

  What (error) message you get? Have you the cable also worked on another computer? Cables can easily go wrong, I suggest you that try another known working cable.

  Alternatively, you can try to reset the power of USB:
  Turn off the computer, remove the power plug from the wall outlet, the battery of the computer femove (laptop), wait a few minutes and then restart your computer.

  Tips for solving problems of USB devices
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

• FN key are no longer necessary, but I need to be

  I've been messing around with the keys, turned off my trackpad, fixed it, but now I have to re activate fn in order to use the function keys, to raise the brightness and stuff, play games that require function keys, but when I play games now, it brings up the function, please help

  FYI, I use a Samsung laptop and my operating system is Windows 8

  Hi Kyler,

  I ask you to answer a question, so that we can diagnose this problem properly:

  What is the complete model of the laptop?

  Usually, Samsung laptops have a key for the function on the top right of the keyboard. Press once on that and check if the problem is resolved.

  If the problem persists, then please contact Samsung support for assistance:

  http://www.Samsung.com/in/support/main/supportMain.do

  Please get back to us with the State of the question.

• USB key is not considered to HP PAVILION CORE I5 and MS 7613

  Hello

  I just got my new HP desktop HP PAVILION CORE I5 motherboard MS 7613 and im trying to install windows 7 without success, because in the BIOS the usb memory key does not START options. Don't see these settings in the bios to boot:

  Floppy boot priority group - not installed

  Group - HP DVD-RAM GH60L CD-Rom boot priority

  Group ST3100052AS HARD drive boot priority

  Network boot priority group - not installed

  More than that, I tried testing with two different usb sticks in different USB ports and the system could not start when trying to install windows 7. The two sticks were properly formatted and I have done some testing old NetBook of the mine and windows 7 have been successfully installed from two flash drives.

  One of my usb stick http://www.amazon.co.uk/PNY-Transformer-Attache-Flash-Drive/dp/B009J0HM94

  Second removable disk is named pro usb drive

  Also two usb keys are seen in the bios on the USB PORTS SETTINGS

  Any direction to help me to windows on my machine is very appreciated.

  Thank you, Bobby

  Check in the BIOS for Secure Boot settting_it must be disabled before the CMU machine can boot from any source in addition to the hard drive. Also activate the Boot legacy. Save & Exit.

  When starting with the USB key, press ESC immediately after turning on. This should bring up the boot F9 option where you use the arrow key to move to the low to highlight/select USB Flash. Press on enter.

• USB key in the machine of W2K3 on ESXi 4 on a Dell Optiplex 760

  I'm testing the new ESXi 4 on a Dell Optiplex 760. In ESXi, I have an Ent W2k3. Machine of R2 SP2 and I want to use a USB device.

  In the config of het windows machine I add the usb controller.

  When I start the machine, I see a 'Remove hardware safely' there is a connected usb controller.

  But if a connected a USB to the ESXi machine it does not appear in the windows machine.

  Should I install additional drivers in ESXi?

  I see if ESXi if he sees the usb ports?

  USB keys are not supported on a virtual computer that is located on ESX/ESXi.

  Incidentally, I don't think not that ESXi is supported Dell optiplex 760... Please see the matrix of compatibility on the VMware Web site.

• External USB devices are not recognized

  * Original title: Ext usb devices appearing is not in my computer

  ACer laptop WIn 7 amd a8 quadruple-heart: when I log about 1 T external usb 2.0 or 3.0 hardrives or key USB 64 G,.
  Device Manager displays the devices, but they do not appear in the list of computers. I have other ext hardrives and the keys that operate without problem.
  I have to go to disk management and see that they appear but they do not have a drive label assigned.
  Then I have to give it a label letter manually it will appear under my computer.

  I tried the same features on a laptop HP with Windows 7 without all these questions.

  Thanks RTierra

  I have found a more permanent solution. At the command prompt, type Diskpart

  type

  automount

  If the answer says disabled, type

  automount enable

  Once I did, my USB keys have been recognized automatically when it is plugged.

  Why the setting has been disabled? who knows.

  I hope this helps others.

• G6 notebook pc Pavilion: Hello, I tried to create a bootable USB key to install Windows XP. WH

  Hello
  
  I tried to create a bootable USB key to install Windows XP. When I tried to copy my files to osi XP USB tool of Flashtoboot my laptop suddenly stopped working with some messages of the blue screen and hit up with a screen that is black with the letter 'J '.
  
  I restarted my laptop using the power button, but all the time, I get a black screen with the letter 'J '. When I tried Ctrl + Alt + Del screen will blink for some time and time again I get the same black screen
  
  By pressing the F1 key, I did the test of memory RAM and hard drive memory. Both tests passed successfully. I tried starting the screen remains black local disk.
  
  Product: Model LAPTOP computer: laptop HP pavilion g6
  Product number: QG470PA #ACJ
  
  OS: Windows 7
  
  Thank U
  Look: -.
  EDWARD07Hello,
  
  I tried to create a bootable USB key to install Windows XP. When I tried to copy my files to osi XP USB tool of Flashtoboot my laptop suddenly stopped working with some messages of the blue screen and hit up with a screen that is black with the letter 'J '.
  
  I restarted my laptop using the power button, but all the time, I get a black screen with the letter 'J '. When I tried Ctrl + Alt + Del screen will blink for some time and time again I get the same black screen
  
  By pressing the F1 key, I did the test of memory RAM and hard drive memory. Both tests passed successfully. I tried starting the screen remains black local disk.
  
  Product: Model LAPTOP computer: laptop HP pavilion g6
  Product number: QG470PA #ACJ
  
  OS: Windows 7
  
  Thank U
  Look: -.
  EDWARD07

  EDWARD07

  Hello;
  
  Let me welcome you on the HP forums!
  
  According to your description, my guess is that the program that you used has replaced the boot files on the hard drive, NOT on the flash drive. Thus, your PC no longer starts.

  To resolve startup problems, you need access to a PC for this phase of work in order to create the necessary support to fix your PC boot loader.
  
  You will need to create something called a CD-ROM to repair Win7 - which you could have done for free when Win7 was working.  This will repair the boot loader files, and if that is the problem, your PC will start OK after that.
  
  But now, which can be obtained (with supplement) from this link: http://neosmart.net/blog/2009/windows-7-system-repair-discs/
  
  When you download this file, it will be an ISO file.
  
  To make a CD bootable it, you will need to download and install ImgBurn: http://www.imgburn.com/
  
  Once you have installed, run, select the option "Save image to disk file" and select the downloaded ISO file and that it points to a blank CD.
  
  To make a USB bootable of it, you will need to download and install RUFUS: https://rufus.akeo.ie/
  
  Once you have that, it is executed in the input of the unit, use the drop down menu to select the USB stick.  Near the bottom right, where is written 'Create a bootdisk to aid', select the ISO file downloaded.
  -------------------------------------
  
  Boot from the media that you have created and follow the instructions in this link: http://www.sevenforums.com/tutorials/681-startup-repair.html
  
  You will probably need to run Startup Repair three times for him to fix all the boot loader.
  
  Once completed, your PC should start OK.

  Good luck

• When I Boot from my USB key to install Windows XP, it will appear not ALL my partitions to install on... Help!

  Yo yet another problem here: S recently, I copied files XP on USB and all that stuff etc... It will start fine after changing the order of boot on USB but when it asks me which partition to install on, it will say "PARTITION1 - LGUSB (3742MB)"... that's all for me, he said, even after making a new partition called "Windows XP Pro"... any help would be appreciated and I thank you guys for help :) especially when I only just registered to MS Answers... Thank you again :)

  -Program used to copy files from the installer:
  WinToFlash (New Version, beta version)
  ------------------------------------------------------------------USB Used:
  Unknown model - LG USB Flash Drive 4 GB
  -----------------------------------------------------------------
  Computer:
  Acer Aspire One D257

  Your User Guide can be downloaded here:

  http://global-download.Acer.com/GDFiles/document/generic%20UG/generic%20UG_Acer_1.0_A_A.zip?acerid=634394037714025697&STEP1=NetBook&Step2=aspire%20ONE&step3=AOD257&OS=all&LC=en&BC=Acer&SC=PA_7
  Once you unpack, you will have your User Guide:
  GUG_ACER_1.0_ALL_AOD257.PDF
  As you can see, there are different ways to restore your Acer. Yes, one of them involves a USB key. Please indicate what method you use.
  Note it is also a method where you would press Alt + F10 at startup (before Windows has the ability to load) to access the partition of the hard drive recovery.
  Yet once, have backed up all your data?

• USB Wizard will not automatically install the usb/flash drives

  Hello

  Working on a laptop, I have a strange problem. Insertion of a usb device (disks hard usb flash are all that I tested) opens the new hardware Installation Wizard.
  If I choose "Install the software automatically", the wizard still fails. If I select "Install from a list or specific location", then choose as location c:\windows\inf, it still works. The wizard should not be checking this place on its own?
  Things I've tried:
  -Reinstall the USB devices in Device Manager
  -Microsoft Fix it 50052
  Gateway, MX6441 laptop
  Windows MCE
  Service Pack 3
  All the important updates installed
  Any ideas would be appreciated.
  Rick

  Hello

  It seems that Windows loses somehow USBSTOR.xxx files in the C:\Windows\INF folder. You can simply copy them from (C:\Windows\System32\DriverStore\FileRepository\usbstor.inf_x86_neutral_83027f5d5b2468d3) to C:\Windows\INF, and that might solve the problem.