USB missing in MAX voice

Similar Questions

• USB-6501 on MAX

  Hello

  I have USB-6501. I would like to have simulated the device on MAX. However, MAX does not seem to offer a device that simulated for USB-6501. I guess that a device simulated for another device would be sufficient to simulate USB-6501. If this is the case, that would do the job?

  Thank you

  Daisuke Takeshita

  The PCI-6503 map will work for your needs as a simulated device? See:

  http://forums.NI.com/T5/LabVIEW/NI-DAQmx-simulated-devices-exception-USB-6501/m-p/554855#M260787

  -AK2DM

• Sensor USB - RAW VISA MAX Sylvac

  Dear community

  I am a new user of LabView and I would like to read the data from a distance sensor Sylvac USB (see here for the link to http://www.sylvac.ch/index.php?page=shop.product_details&flypage=flypage.tpl&product_id=201&category... sensor).

  When I use the software provided by Sylvac, no problem everything works fine.

  Note that it is not possible to create a secure Channel as Sylvac does not provide drivers for this particular sensor unlike this post http://forums.ni.com/t5/LabVIEW/How-to-read-out-data-via-usb/td-p/2042980 .

  I created the driver NI-VISA following this procedure (Assistant of the Driver NI-VISA)

  http://www.NI.com/white-paper/4478/en/

  In the MAX, the sensor is correctly detected.

  With the help of a Cokehead USB (USBlyzer) and using Sylvac software and drivers, I found that the software sends a command for the sensor to apply for the position (? \r or 3F 0d in HEXADECIMAL) and the sensor to respond by sending the position (see attachment for USBlyzer report).

  When I do the same thing with MAX test panel and drivers of NI-VISA, I am able to see the 0d 3F, then the 2-byte buffer, but no return of the sensors (see attachment).

  Anyone know what I am doing wrong, or what direction I should look for?

  Thanks in advance

  Best regards

  Florian

  I finally "solved" the problem by changing the sensor with the USB to one with RS232. Thanks for your replies.

  Florian

• the external drive BIOS boot option usb missing

  I am trying to boot from an external USB device.  I have a DELL with a Pentium M with WINDOWS XP.  I entered Setup via pressing F2 at startup.  I changed the BOOT SEQUENCE so that a USB storage device is top of the list.  I rebooted the computer & F12 key to display the options of start & USB device are not yet listed.  As far as I can tell when the computer starts, it uses the internal hard drive & not the USB device.  This computer has more than 1 USB port.  Y at - it a specific USB port I need to use, or is not properly enabled USB option because I don't even see it not as an option when I press F12 at startup.  If it is not properly active how can I do so?

  I am trying to boot from an external USB device.  I have a DELL with a Pentium M with WINDOWS XP.  I entered Setup via pressing F2 at startup.  I changed the BOOT SEQUENCE so that a USB storage device is top of the list.  I rebooted the computer & F12 key to display the options of start & USB device are not yet listed.  As far as I can tell when the computer starts, it uses the internal hard drive & not the USB device.  This computer has more than 1 USB port.  Y at - it a specific USB port I need to use, or is not properly enabled USB option because I don't even see it not as an option when I press F12 at startup.  If it is not properly active how can I do so?

  I think that I activated correctly now, I see the USB option when I press F12.  I don't know why it does not appear initially, but it does now.   Now, I have a related associated error hal.dll missing or corrupt.  I started another thread on this question, so if anyone has knowledge on this departure: http://answers.microsoft.com/en-us/windows/forum/windows_xp-system/imaging-an-xp-system-on-an-external-harddrive/adcf7894-bd6e-4fcd-94d0-3b1894e8020c

• USB missing on hp 15-b041dx after down ranking for windows 7 64 driver

  I uninstalled windows 8 on a 15-b041dx hp and installed windows 7 64-bit.  I have all the drivers usb excenpt the hardware id is VEN 8086 DEV 1e315subsys 1900103c rev4 anyone know where can get the windows 7 drivers for this machine?  I found out it is a chipset intel but I am at a loss.

  Thank you

  Mark

  I FOUND IT HERE - > http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4063 & lc = on & cc = us & dlc = in & sw_lang = & product = 5278311 #N269

  The USB chipset worked!

• USB missing 6009

  Hello

  Way to there Tester - you it the United Nations United Nations vi Labview without having the USB-6009 plugged to the computer?

  Is - it a Simulator or other?

  CDLT.

  Hello

  Indeed, it is possible to simulate a DAQ card.

  I invite to watch the document below which explains step by step how to do:

  How to create a NO-DAQmx simulated device

  Nice day

• NOR CAN missing in MAX 9862

  I am trying to set up a controller 9014 cRIO with the module OR 9862 CAN, but I see no MAX after I plug in and restart the 9014.  I'm running Labview 2013 and Ithink I installed all the relevant software on the host machine and the 9014. See the attached screen capture and you can see that the 9862 is not displayed.  Any ideas?

  Thank you

  Todd Moore

  University of Illinois

  Unfortunately not. As mentioned earlier, the 9862 won't work on cRIO-911 x / x 908 / 906 x chassis ... 9102 is not in the list.

  The 9862 requires a chassis with one of the following FPGAs: Virtex-5 / Spartan 6 / Artix-7. The 9102 has a Virtex-II FPGA, which is well below the minimum. This is the reason why you are not able to function with the module.

  I recommend that you get a cRIO-9118 in replacement. This chassis supports the 9862 and there also 8 slots.

  I hope this clarifies the issue.

• EliteDesk 800 G1 USDT: usb ports do not provide enough power

  We have a scanner usb requiring 500mA of power.  However, for many of our clients using HPs, the usb ports do not provide enough power to the scanner causing the application to crash.  Some customers use the HP EliteDesk 800 G1 USDT, others use HP zero client t310.  Connect the scanner to a usb hub powered solves the problem every time.

  Y at - it changes, they can do for the Bus USB controllers to ensure that a particular port will be able to provide 500mA so they did not need to buy a usb powered a system hub?  Or do you have another suggestion?

  Thanks in advance.

  I'm not familiar witht eh models accurate but 500MA is the output for USB 2.0 max but 3.0 can go higher have you tried usingn 3.0 ports if not you can also get a cable Hat uses the power of 2 ports.  Many systems have problems with the only Scanners USB and power supply.

• Question on size USB for upgrade to blu - ray player

  Hello
  I have a question: if I want to move (for example bdx2300) Toshiba blu - ray player, the Toshiba site says (instructions for the installation of the upgrade in the guide 'how to upgrade the F/W'):

  "Firmware update requires USB Reader of maximum size of 2 GB. .... "

  Is there a restriction on the size of usb, that blu - ray player may take during the upgrade? There is mention of having need a USB 2 GB max size to work... but I only have a key of 8 GB

  Thank you

  null

  > but I only have a key of 8 GB
  And have you tested the 8GB memory stick? Doing a job?

• Can you change the type of device to 'USB Raw resource' to GPIB controller?

  I'm trying to configure a GPIB FL Contec GP - IB (USB) controller in MAX.  I could so he can register through the creation of a pilot of the Assistant driver VISA, but it fits as a "gross resource USB" rather than as a GPIB controller.  I can send and receive information from the controller, but it does give me an option to search for connected devices of GPIB communicate with them.  Is it possible to change the type of the device, maybe by manually changing the driver created by the wizard of the NI-VISA driver?  Thank you for your time.

  N ° do not use MAX at all. You can just create a GPIB-USB controller on your own. You should contact the seller.

• Question of GPIB-USB-HS

  Hello everyone, I have 5 machines hooked: set of 2 meters, which connect to a power supply that goes to a function generator and led to a thermostream which then my GPIB-USB-HS is used to hang my computer. I am running an executable file from a previous VI, I tested on the computer that has the original VI. I have the correct runtime downloaded, and I can open the VI. There isn't an arrow broken for the execution button, but when I run it, it immediately stops running as if the VI running, but nothing happens. No errors or messages. It's as if nothing does not communicate. So my first instinct was to control the GPIB. They are all tight, and I checked to see if maybe the instruments were not recognized by the GPIB-USB-HS, but MAX watch I have all 5 connected instruments when I 'Search tools'. On the GPIB-USB-HS, there are a light yellow/orange on the loan and nothing on the assets. The GPIB correspond all too much, and the address for the GPIB-USB-HS is set to 0.

  Thank you.

  You can create the exe with active debugging and place probes to determine what is and what is not running.

  Also, you don't mention if you have installed the runtime of NI-VISA.

• How to send and receive simple controls USB?

  Hello

  Before you begin. I read om internet (USB tutorials, nuggets, etc) for 2 days get it.

  but it's really confusing and I still have no idea how to do that. So I ask for your help.

  I install a USB device in MAX.

  I need to send this command: 0x0 2 M 1 x 3

  Were 0 x 2 sets the start and 0 x 3 sets the end of the command.

  I think I have to use a transfer of control, but I do not understand what it takes to use the Index, the value of request,

  Request and length entries. I don't understand how sent Hex and ASCII and Dec at the same time.

  Should I convert these values?

  I would really appreciate some examples of code. Can I use the VISA controls?

  Bravo will be granted, thank you in advance

  Heinen wrote:

  I need to send this command: 0x0 2 M 1 x 3

  I don't understand how sent Hex and ASCII and Dec at the same time.

  Should I convert these values?

  I'm not sure of the Index, the value of ask.

  But on sending your comand...

  I guess that the space before the "M" and the space after the "1" is not necessary,

  but the space between the "M" and the "1" is required

  

• Could not detect USB RIO 7856R in labview 2012 SP1

  Hi @all,

  Why I couldn't detect 7856R USB RIO in labview 2012 SP1? I already install drivers include DVD, see (USB-7856R) in max or, but can not add it to the project manager.

  Data sheet says its compatible (between LV2012 and 7856R)!

  Hey damienski86,

  According to the product page (tab "Panorama"):

  Required software 
  This product requires the LabVIEW FPGA Module 2013 or later Version and NEITHER-RIO Version 13.0 or later driver software.

  I think that you will have to go up to the latest software (2013 SP1 came out today) in order to be able to use your new hardware. Where do you see that the device is compatible with 12.0 specifications?

• BDX4350KB Wifi adapter and firmware upgrade doesn't work do not

  It is a sequel to my earlier question about if the WLM-20U2 Wifi adapter will work in my blu - ray player.

  After buying the adapter I plugged it and a message 'not supported', if I tried to connect wireless it says there was no an adapter connected.

  So I assumed that this necessary upgrade, so I formatted a 1 Gb USB drive with the FAT file system, downloaded the file level (version 39 http://www.dl.toshiba.com/player/NA/GB/EN/BDX4350KB.html) and copied the file .bin on the USB.

  When I plugged into the player and said to check the disk for a file to update it tells me that "frontend file is not found"... There was only one file to download, and it wasn't in a folder so I guess I'm supposed to just copy that file on the USB drive.

  I checked the USB port with a memory stick with photos on and it works fine.

  How to get the upgrade to work in the hope that it will enable the wifi adapter to work?

  Thank you

  Have you checked the guide in PDF firmware update?
  [Update firmware BDX4350KB | http://fget.dl.toshiba.com/manual/install/10009/Installation_Instruction.pdf?fromPid=%2Fplayer%2FN A%2FGB%2FEN%2FBDX4350KB.html&f=Installation_Instru ction.pdf]

  _ * How to upgrade the F/W * _

  (1) update firmware requires the USB of size max.2GB. Please make sure you format the Flash DRIVE to FAT/FAT32 before you start the upgrade procedure.
  ? Create a new folder on the USB drive and name it UPG_ALL
  ? Unzip the firmware file and copy it in the folder UPG_ALL.

  2) turn on the BD? Drive and make sure that you can see the player's on-screen Menu.
  ? Insert the USB key containing the Firmware upgrade file in the USB of the Blu slot? ray player

  3) press the "SETUP" button on the remote control.

  ? Select keys on the remote control UP/DOWN
  ? Symptom
  ? Upgrade
  ? USB storage device

  4) press the OK button on the remote control depending on the USB storage device.
  ? Now the upgrade file is under research. Please wait massage will appear

• FireWire 400 and 800 speed question

  I recently bought one of these cords off of eBay for a few dollars.  I have an old external WD which was connected by usb 1.0.  I thought I could get more speed with this cord, but I get all the same read and write speeds of close to 23MBS.

  Any ideas why the speed is slow?  Cord? By car?

  Thank you!

  USB 1.0 MAX is 12 Mbps, which is 1.5 Mbps. (b = bit, B = byte [8-bit]).

  FireWire 400 MAX is 400 Mbps, which is 50 MB/s.

  Without knowing the specifications of the car, I guess that the "old external WD' performance is the limiting factor.