USB recognsied but mass storage devices won't allow drivers to be loaded "access denied."

installing the drivers for them, but when I plug them in I get the message 'new hardware found, windows found driver software for your device but encountered an error while trying to install' access denied.

I have renamed and deleted the infcache.1 but it does not work

Hello

Check here first:

Control controllers Control Panel - Device Manager - USB Serial - USB mass storage devices (you can have
more than one - If Yes check all) - double click on the driver tab - click Driver Details - the default is
C:\Windows\System32\drivers\USBSTOR. SYS (the C:\Windows is where you installed windows
If not C:\Windows\) you can't have one for your car if it not recognized - when it is recognized
and if doesn't work does not correctly return to this step.

Check again once you advance through them.

2nd check these:

Operating instructions: find 'lost' Windows Vista drivers when you add a new device
http://www.texxors.com/content/how-find-lost-Windows-Vista-drivers-when-adding-new-device

Tips for solving problems of USB devices - and a Mr Fixit
http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

Hardware devices not detected or not working - Mr. Fixit
http://support.Microsoft.com/GP/hardware_device_problems

-------------------------------------------------------------

If no joy:

Make a Restore Point

Control Panel - Device Manager - click in the empty area - VIEW - show hidden devices

Now look everywhere EXCEPT the USB controllers for your device (cannot be found) and if you find
It RIGHT CLICK and UNINSTALL all. The device is your (s) or similar.

now go to the USB and UNINSTALL ALL controllers in the category, but the category itself.

APPLY/OK

RESET

This refresh battery USB and hopefully it will allow the unit to install. (You may need a powered hub)

Here is the similar procedure under XP, Vista is the same, except that we need to clear the specific device if present.
http://support.Microsoft.com/kb/310575

This is a utility to help you, but do 1 above.

USBDeview is a small utility that lists all USB devices currently connected to your computer, as well as all
USB devices that you previously used. Run Options and check the 1st three choices to see if one is there.
Try to remove all instances and restart then plug the drive.
http://www.NirSoft.NET/utils/usb_devices_view.html

--------------------------------------------------------------------
Check this box:

Start - type in the search box - Windows Disk - find Windows Disk Management on the list above.
Click - look RUN AS ADMIN to see if there is a letter assigned or a conflict of law or the
drive letter assigned is not the one you used to see. This may show of course not the
Road at all, it's just a check.

-------------------------------------------------------------------
http://www.Uwe-Sieber.de/usbdlm_e.html
Its complex however, the site has a lot of help.

And all this?

See also this thread and those it refers too.
http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/ff81438c-EAC5-4b38-8b89-d1a1dbe837f3

I hope this helps.

Rob - bicycle - Mark Twain said it is good.

Tags: Windows

Similar Questions

  • How to boot from simulated USB (flash drive) mass storage device?

    I do some development work on the anaconda, the Installer used by Red Hat Enterprise Linux and reconstructions based off of him.  I'm testing support of USB flash drive facilities and would rather test my changes using image files from a USB drive physical - a bit like editing an .iso image to a CD instead of using a physical CD of closure.

    I found a reference to the Framework of Linux-USB Gadget API, which looked exactly like what I was looking for.  After the reconstruction of the almond, I was able to run:

    • modprobe dummy_hcd
    • modprobe g_file_storage file = CentOS - 6.2 - i386 - netinstall.iso

    After that, the office immediately get the image as if I had actually plugged a USB stick with the same content.

    I am also able to connect this virtual USB device to a virtual machine, but when I start the virtual machine, it has no option to boot from the virtual USB device.

    Any ideas?

    VMware Workstation does not directly support boot from USB but you can use a third-party utility called Plop Boot Manager to boot a bootable USB disk and you may be.

  • Laptop HP Pavilion: mass storage device problems

    I have a 1 TB mypassport mass storage device connected to the computer.  When I access the camera or only 32 MB of storage is displayed. You go to properties and looks like it is partitioned and do not show the capacity of all of the device I'm so lost

    I discovered what had happened. I had put off the hard for the recovery of the system and, in so doing, so blocked 32 MB disk and the rest was just let go. I had to go back and assign a new drive for the rest of the unused portion. I always learn something... Thank you all.

  • Administrator has restricted this computer to access the USB/1394 mass storage devices

    This message just started showing unexpectedly. Sometimes windows load. It is not and has never been a business machine, so I am the administrator.

    He has blocked my external hard drive up and now won't let me even to read a memory stick. In this case, I get «the administrator has denied access to USB/1394 mass storage devices»

    I searched through everything, and everything seems ok. I ran several controls of virus and spyware checks, but all come clean.

    I hope someone can help me. Thank you.

    You use Acer computer?

    If so, then uninstall: Acer LanScope or update and see if that resolve the problem.

  • Impossible to safely remove external USB HDD - ejection of mass storage device problem

    Hello

    I have a 250 toshiba external hard drive. "When I go safely remove device and click on stop, guests me that ' ejection of mass storage device problem and try later.

    Is there a reason for this? As I have heard it is dangerous to pull the cord without stopping it first.

    This happens usually when something is always access to the USB - HDD.
    Yes, it s dangerous to pull on the cable, because you can lose some data and the file system may be damaged. But if you have a situation where you need the drive to take with you and want to just get out the cable to the USB port there is a little trick to disconnect the security apparatus:

    Do right click on 'My Computer'-> click on Hardware-> click "devicemanager"-> go into "diskdrives"-> then you need to click on the drive that is your USB - HDD-> with the right button and then click on 'Properties'-> in the menu properties of this drive, you must go on "policies" and click on "optimize for quick removal"-> and then click OK and exit this menu and all-> perform a reboot-> closing information fact. :)

    After that, it s safe for remove you your drive even if it s not ejected. :)

    Welcome them

  • Installation question on Satellite M30 PSM30E USB mass storage device

    Hi people,

    I get an error message when I try to install new hardware on my laptop. Windows XP is trying to find the drivers and then comes up with the following error after a few minutes. The software starts to install but then comes with the following text:

    "There was a problem installing this device:"

    USB mass storage device
    An error occurred during the installation of the device
    These data are incorrect

    What happened with a USB card reader and my mobile. Once I have the error box I get a message saying that the device will not work properly?

    Anyone has any ideas at all?

    See you soon

    Hello

    What series of notebook or laptop model do you have?
    Could you please put the whole number? It would be very useful for further study.

    All the installation driver Toshiba must be made in the right order.
    In most cases, you would find a txt file of installation instruction on the Toshiba driver page.
    You must follow these instructions to ensure that all drivers would be executed correctly.

    Concerning

  • Passport Mass Storage Device does not appear to the top, when I plugged in the USB Port on Windows XP

    I have connected my passport mass storage device to a USB port and it notifies as new hardware, but it did not show in my computer anywhere. However, I installed and uninstalled several times my computer.

    Hello

    1. what happens when you plug the device to your computer, you get an error message?

    2. don't you make changes to the computer until the problem occurred?

    I suggest you try the steps mentioned below and check if it helps.

    Method 1:

     Try to connect the Passport mass storage device into the other USB port or try to connect the Passport mass storage device in another computer and verify that the problem persists.

    Method 2: Try running the Fixit tool from the link below.

    Hardware devices do not work or are not detected in Windows:
    http://support.Microsoft.com/GP/hardware_device_problems

    Method 3: Also try to follow the steps from the link below.

    A computer that is running Windows XP cannot detect a USB, an Apple iPod flash drive or an external hard disk drive: http://support.microsoft.com/kb/925196

    Hope this information is useful.

  • ProBook 350 G1/F7Y90EA: USB mass storage device driver

    Please help to install driver!

    Do not see my 350 Pro Notebook USB 3.0 Flash. He early find, but do not work automatically and he lost.

    See the problem in the USB mass storage device driver.

    I tried to put in day, but Win can't find this driver...

    External disk HARD 3.0 works. USB 2.0 works in all usb ports. But USB 3.0 - no flash (this is new).

    I tried to find the driver on the support page, but I couldn't find it.

    Thanks in advance!

    Lyuba wrote:

    Please help to install driver!

    Do not see my 350 Pro Notebook USB 3.0 Flash. He early find, but do not work automatically and he lost.

    See the problem in the USB mass storage device driver.

    I tried to put in day, but Win can't find this driver...

    External disk HARD 3.0 works. USB 2.0 works in all usb ports. But USB 3.0 - no flash (this is new).

    I tried to find the driver on the support page, but I couldn't find it.

    Thanks in advance!

    Are you sure that the USB is not bad? Also have you tried on some other computer USB3 ports to see if those who can see the drive? Looks like your USB is not USB3 if it can read the disk HARD USB3 but not the USB3 Flash in question. Also make sure that your laptop ports are USB3 ports? In the contrary case, we owe this: to check if the ports are USB3...

    How can I find my model number or product number?

  • is a label of ok usb mass storage device or I have to force vista to recognize the hd?

    on a computer hp laptop double heart running vista;  try to use the old never used western digital 500 GB caviar blue as disk hard external for backup/storage purposes. Vista does not except as a usb mass storage device.  as soon as I arrive at the radio Shack to the cheap ide cable, I need to decide on the way to go here. I want a clean version of vista that is stored in its own partition, one for general campaigns and then one for pictures, etc... .  I'm ok with mass storage or not here? No geek.
    Thank you!
    John

    Hi John,.

    You are able to access the external hard drive or not?

    The external storage device will appear only as usb mass storage device.

    You can use the external device for general storage purposes but the operating system should be stored in the internal hard disk only.

  • It lacks a computer on my new USB mass storage device.

    When I plug my two sticks of SanDisk U3 into my computer, my brand new computer does not recognize them. I passed to the Device Manager and looked under controller universal serial bus, while it is in my USB and the mass storage deivce is not displayed. I have windows vista on this computer and my laptop. These work on my laptop very well, but not on this computer. I bought the full version of Windows Vista and have the disk. I have this installed on 1 computer.

    Hello

    Check with SanDisk support because they have excellent online support, including live Chat and documentation.

    SanDisk - Support
    http://KB.SanDisk.com/app/home

    See also the appropriate bodies of SanDisk:

    SanDisk - Forums
    http://forums.SanDisk.com/

    http://www.SanDisk.com/SanDisk-support/forums

    ===================================

    Added troubleshooting:

    Control controllers Control Panel - Device Manager - USB Serial - USB mass storage devices (you can have
    more than one - If Yes check all) - double click on the driver tab - click Driver Details - the default is
    C:\Windows\System32\drivers\USBSTOR. SYS (the C:\Windows is where you installed windows
    If not C:\Windows\) you can't have one for your car if it not recognized - when it is recognized
    and if doesn't work does not correctly return to this step.

    Check again once you advance through them.

    2nd check these:

    Operating instructions: find 'lost' Windows Vista drivers when you add a new device
    http://www.texxors.com/content/how-find-lost-Windows-Vista-drivers-when-adding-new-device

    Tips for solving problems of USB devices - and a Mr Fixit
    http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

    Hardware devices not detected or not working - Mr. Fixit
    http://support.Microsoft.com/GP/hardware_device_problems

    -------------------------------------------------------------

    If no joy:

    Make a Restore Point

    Control Panel - Device Manager - click in the empty area - VIEW - show hidden devices

    Now look everywhere EXCEPT the USB controllers for your device (cannot be found) and if you find
    It RIGHT CLICK and UNINSTALL all. The device is your (s) or similar.

    now go to the USB and UNINSTALL ALL controllers in the category, but the category itself.

    APPLY/OK

    RESET

    This refresh battery USB and hopefully it will allow the unit to install. (You may need a powered hub)

    Here is the similar procedure under XP, Vista is the same, except that we need to clear the specific device if present.
    http://support.Microsoft.com/kb/310575

    This is a utility to help you, but do 1 above.

    USBDeview is a small utility that lists all USB devices currently connected to your computer, as well as all
    USB devices that you previously used. Run Options and check the 1st three choices to see if one is there.
    Try to remove all instances and restart then plug the drive.
    http://www.NirSoft.NET/utils/usb_devices_view.html

    --------------------------------------------------------------------
    Check this box:

    Start - type in the search box - Windows Disk - find Windows Disk Management on the list above.
    Click - look RUN AS ADMIN to see if there is a letter assigned or a conflict of law or the
    drive letter assigned is not the one you used to see. This may show of course not the
    Road at all, it's just a check.

    -------------------------------------------------------------------
    http://www.Uwe-Sieber.de/usbdlm_e.html
    Its complex however, the site has a lot of help.

    And all this?

    See also this thread and those it refers too.
    http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/ff81438c-EAC5-4b38-8b89-d1a1dbe837f3

    I hope this helps.

    Rob - bicycle - Mark Twain said it is good.

  • Problem ejecting USB Mass Storage Device [Unlocker doesn't work]

    Hey everybody,

    Just like everyone else, I get a pop-up message when trying to eject my external hard drive WD: "problem ejecting USB Mass Storage Device. Windows can't stop... "and so on." This does not work when I've only sailed on the disk, but it does, for example, when I made a mistake - check or make a backup. I already checked the forums, but unlike everyone else, third-party programs do not work for me.
    I did the following:

    -closed open task

    -disabled virus scanner

    -used Unlocker and Process Explorer, but he can't find any process that locks my drive. What happens here?

    -rebooted in safe mode

    -disabled indexing

    It makes me crazy that I have to restart whenever I want my drive to eject.

    Oh, and I use Windows 7.

    Can someone help me solve this problem?

    Hello

    (1) is limited to any specific USB device?

    (2) did you try to connect the device to a different USB port and check if you are facing a similar question?

    This problem may occur if there are handles open with all the files in the USB (Universal Serial Bus) mass storage device are in use by another program. Follow these methods and check if that helps.

    Method 1:

    I suggest you run the hardware and devices Troubleshooter to check if it helps.

    Open the hardware and devices Troubleshooter

    http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

    Method 2:

    I suggest you to check and clean the boot if any third-party program is causing the problem.

     

    How to troubleshoot a problem by performing a clean boot in Windows Vista and Windows 7

    http://support.Microsoft.com/kb/929135

     

    Warning: After you used the clean boot in order to solve your problem follow step 7 to reset the computer to start as usual.

     

    Connecting and disconnecting USB devices:

     

    Most USB devices can be removed and disconnected at will. When you unplug the devices of storage, such as USB flash drives, you should be sure that the computer has finished saving all the information on the device before removing it. If the device has an activity light, wait a few seconds after the light has finished flashing before unplugging.

    If you see the icon remove the device safely in to the far right of the taskbar notification area, you can use this to ensure that devices have finished all operations in progress and are ready to remove. Click the icon and you will see a list of devices. Click the device you want to remove.

    You can use any USB port when you plug in a device you have installed beforehand. However, the first time you connect a device to a particular port, Windows will install the driver for this device again.

  • "This USB mass storage device can transfer information faster if you connect it to a USB 3.0 port Superspeed ' when the device is already connected to a USB 3.0 port.

    I just bought and installed a USB 3.0 card. It is the Startech PEXUSB3S2 PCIe card. I installed the card in a PCIe 2.0 X 1 slot. The manual says it's exactly the slot, that it supports.

    The Manager device displays NEC Electronics USB 3.0 Host Controller and NEC Electronics USB 3.0 Root Hub are installed and are working correctly. I have a Thermaltake BLACX5G 5 G USB 3.0 hard drive caddy. The transfer rate is only 35 MB/s using the HDTune benchmark. It is a USB 2.0 speed.

    When the player is turned on, windows displays the message "this USB mass storage device can transfer information faster if you connect it to a Super speed USB 3.0 port»

    For some reason, the system doesn't see the caddy to drive USB 3.0 as being plugged into a USB 3.0 port, when it actually is.

    I remember having this same problem with Windows XP, when I bought a USB 2.0 card. The only thing that fixed it at the time was upgraded to XP SP2.

    This should not be a problem because I know that Windows 7 pro 64-bit supports USB 3.0.

    My motherboard is an ASUS P5QL-EM support an Intel Core 2 Quad and 4 GB of DDR2 memory. According to the manual owner the PCIe x 1 slots support architecture 1.0 and 2.0.

    Edit: I just tested the external hard drive and expansion card USB 3.0 on my motherboard Gigabyte of friends running Windows XP. Everything worked perfectly, no problems at all.

    Here, there is a problem with Windows 7 or the motherboard. Still unresolved, currently installs a floppy drive so I can update the firmware of my motherboard.

    I checked the implementation of the card several times, removed and installed in another motherboard to test, then removed and reinstalled again in my motherboard ASUS check several times for a fit course.  It still does not work. I have just completed update the firmware of the motherboard with the latest version, and I also did a new install of Windows 7, install the drivers USB 3.0 immediately after installing Windows over. None of this solves the problem.

    I'm running out of ideas on how to fix this without doing something drastic as a replacement for my motherboard. I don't want the speed of USB 3.0, but I don't think I'm ready for an another two or three hundred dollars to get it.

    I've been all over the ' net trying to find a solution and read tons about USB USB 3.0 specifically and in general. I can find no reason why the drivers would install and report that they are working correctly, but fail to connect to 3.0 speeds. I think that this would generate a certain type of error instead of such a strange symptom.

    EDIT:

    Here go us. I knew that is was a bad idea to buy one main (ASUS P5QL-EM) card that had to be overclocked to 1066 MHz for DRAM memory. I did all this work, and every time I reset my BIOS or updated it would always be the frequency DRAM back to where it should be (1066). After a reset of the computer was the starter and I just let it start instead of setting the DRAM frequency and, suddenly, USB 3.0 card worked perfectly. I confirmed this by setting the frequency to 1066 and looking at the USB 3.0 card fail again. I guess it must have something to do with the clock being sent to the PCIe bus.

    In any case, the USB 3.0 card works perfectly and gives me a transfer rate HD Tune to 99 MB/s on a drive from WD SATA 7200 RPM and 86.1 Mbps on a Samsung drive hard 5400 RPM / MIN 3,5 "SATA. These are the same reference points I get when these drives are connected to my internal SATA connectors. I'd say USB 3.o works perfectly now and maxing out the hard drives performance.

    Thanks for any help.

  • Message "USB Mass Storage Device does not work properly"

    Ran AVG PC tune up and referred the problem message "USB storage device work does not correctly. I went to Device Manager, clicked on "bus USB controllers. He showed the device with a yellow exclamation point USB mass storage. I have double clicked on it, went to the drivers and updated the driver. I received a message that the driver was already updated and got a message "device cannot start (code 10).»

    I thought that maybe he was looking for the storage device of mass external and plugged on the USB port. He has shown in the Device Manager under the other mass storage device but had no yellow exclamation point (I guess that means it's very good).

    Is there an internal procedure and what can I do about this problem? My development program, said that this mistake could cause my computer crashes often or he can go for a long time without replying (which it does).

    Hate to be chatty but I wanted to present all the facts.

    Can someone please help me get this figured out? Thank you in advance.

    Hello Sammy,.

    Please provide detailed information about your question. I appreciate the step by step troubleshooting, and pain that you have taken to resolve your problem. However, there are a few steps more that we can try to diagnose the root cause and to check the health of your system, to solve the problem permanently.

    Microsoft does not recommend using third party software melody. That running these software can damage records.

    For the problem with the error code 10, I would ask you to try the steps below:

    A Code 10 error is generated in the Device Manager in one of the following situations:

    1. Device Manager cannot start the device.
    2. One of the pilots who needs the unit does not start.
    3. The Device Manager has insufficient information to recognize the error that spread upwards by the device driver.

    Note: In this case, the Code 10 error can be a very generic message indicating some sort of unspecified driver or device problem.

    Error Code 10 is mainly related to devices and hardware driver problems or compatibility problems between the drivers of equipment and additional software that is installed in Windows. Therefore, we recommend that solve you these problems with emphasis on device drivers, configuration of device problems and hardware compatibility issues.

    I suggest you to follow the steps described in the following Microsoft article and see if it works for you.

    FIX: "this device cannot start" error Code 10 in the Device Manager in Windows

    Hope it would help. If problem persists always post back with the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

    Thank you.

  • USB Mass Storage Device show me error Code 10

    I have problem: USB Mass Storage Device Error 10 Code. I tried to uninstall all devices under USB controller then I restart my computer. The problem is still exist. I tried to find and remove UpperFilters and LowerFilters in the registry but I they are did not exist in the HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ (36FC9E60-C465-11CF-8056-444553540000). My laptop: Toshiba Portege R705-P25 Type powered by Windows 7 Home Premium. Is there a solution to my problem?

    Concerning

    Leo MS

    Hello Leo,

    Thanks for joining us.

    The Code 10 error applies mainly to the problems of hardware driver and devices or compatibility problems between the drivers of equipment and additional software that is installed in Windows. Therefore, we recommend that solve you these problems with emphasis on device drivers, configuration of device problems and hardware compatibility issues.

    See the article mentioned below.

    Description of errors related to the 10 Code that generates the Device Manager in Windows on computers
    http://support.Microsoft.com/kb/943104

    Method 1: You can run the below mentioned link Microsoft fixit and check.

    Hardware devices do not work or are not detected in Windows

    http://support.Microsoft.com/mats/hardware_device_problems/en-us

     

    Method 2: Remove and reinstall all USB controllers:

    To remove and reinstall all USB controllers, follow these steps:

    a. click Start, click run, type sysdm.cpl in the Open box and then click OK.

    b. click on the hardware tab.

    c. click the Device Manager button.

    d. expand Bus USB controllers.

    e. right-click every device under the USB Bus controllers node, and then click Uninstall to remove one at a time.

    f. restart the computer and reinstall the USB controllers.

    g. plug in the removable USB storage device and perform a test to ensure that the problem is solved.

    Let us know if this can help, we will be happy to help you.

  • USB Mass Storage Device gives me the Code 10 error. This device cannot start

    I have an external hard drive, Iomega Prestige 1 TB and one of the people at the school he fell from the top of the computer tower that resembled a fall of 30 cm, after it still worked, but then a few minutes later there not later he was still able to connect but it kept asking me to format it , so I wanted to try and find a way to get my data without formatting it. A day later I plugged the external hard drive, it started to beep for 5 min then it connected to the computer but unfortunately didn't show up in my computer, but he did it in the printer and peripheral. I checked my device manager and it showed a yellow explanation mark with the USB mass storage device. I went to properties and it says: "this device cannot start. (Code 10) "How can I solve this problem?

    Hi AntonioDavism,

    You can check if the following is useful.

    Method 1: Run the hardware and devices Troubleshooter and check if that helps.

    Method 2: Follow the steps in the below article mentioned and look for the question.

    Description of errors related to the 10 Code that generates the Device Manager in Windows on computers

Maybe you are looking for

  • Satellite P500 - Solution how to operate sound on XP 32-bit and 64-bit

    Hi all..Now, I write here how I did something that seems impossible...I mean sound running on a computer satellite phone / qosmio p500/505 300/500and other models with Conexant sound card high definition on x 32 / x 64 Windows XP sp2/sp3...I know tha

  • Ask stuck in Mode full screen

    Hello, my request of makerbot is stuck in mode full screen on el capitan. Im not sure if I have the application correctly all in full screen. The app was windowed with yellow red and green buttons at the top left as a normal window. Every since I wen

  • How can I upload photos to the computer of my kodak camera?

    I have my camera connected to the computer and I don't know if I'm supposed to have an application up, so the pictures can be uploaded to the camera comouter...

  • E260 will not go past the opening screen

    I got my 260 E for about a year and later that yesterday I went to turn it on, but it remains on the logon screen. Enter mode 'sleep', but I can't listen to music or find out anything because it will not go beyond the opening screen. The second of 10

  • Error processing request. ORA-06502: PL/SQL: digital error or value OK

    HelloI want to open a session in an APEX application using the IE 8 browser, but I can't because this error:ErrorError processing request.ORA-06502: PL/SQL: digital error or valueOkI can run this app with Chrome or Mozilla, but I need to open it with