USBTMC Data Acquisition Device Firmware

Similar Questions

• Is it possible to change the name of data acquisition device?

  Hi all

  Is it possible to change the name of device of data acquisition in a pragmatic way?

  I wish I had at the beginning, when I start the data acquisition control a name that my .net program assigns to the DAQ card. Is this possible?

  Thank you

  Virginia

  Ashly thanks!

  Virginia

• Not displaying data acquisition devices is not under the chassis to MAX after updating drivers OR

  We use a PXI-1031 chassis and 3 PXI-6143 devices to our MetalMapper of the geometry. Also the chassis appears only in MAX as "unidentified" and PXI-1031 is not displayed in the list "identify as".

  Thanks for your reply... uh... PeanutButterOven

  After having looked in the information requested for our controller, we realized that we had a wrong model for our controller number.

  After we have determined the correct model number (NI PXI-8108), we could assign to the unidentified PXI system in the "identify as" drop-down list in MAX > my system > devices and Interfaces and then select our chassis model number (PXI-1031DC).

  After we did it, a new object was automatically created called PXI-1031DC 'Châssis 1' and our devices were already provided in a drop down of this frame object.

  Thanks for your help!

  We now live a new show with our custom software that seems bound to not find .NET drivers even if they exist on our computer.  This seems to be a separate problem and we will publish it to a new discussion if we're stuck.

  Thanks again

• How to know the number of USB data acquisition device

  There are 2 devices and user can plug in different port each time.

  But the program uses the same string of device and may have errors.

  They can auto detect and generate the device chain, thank you.

  Is this something similar to this (using) you need? If so, please go from the link to Andrew post (a 2nd). Post if you need something else.

  Thank you

  Mathan

• motion control for vertical actuator and data acquisition

  Hello

  I am a researcher (a branch of civil engineering) geotechnical engineering and I have very little knowledge about the acquisition of control and data motion, so would need a lot of help from the experts OR. I have only knowledge base on these 2 aspects based on my reading of some materials on the Web site of NOR and youtube videos, so I hope that you bare with me . Here are my questions:

  I am trying to build an actuator which will be used to push a probe (a penetrometer with a load cell to measure the resistance of a soil sample), resembling the concept, photography in the attached file. I need to have these criteria for my system:

  (1) actuator, which can push the probe at speeds between 0.01 mm/s - 300 mm/s with precision and move the probe cyclically (upwards and downwards) in the vertical direction
  (2) load expected on the probe into the ground range: 0.02kN - 6 kN.
  (3) necessary to get the load cell load data and the speed of the probe.

  4) able to control the actuator to a PC (speed and posotion) and monitor data from transducers and data log time even the transducers.

  Guess my beginners is that I will need:

  For orders:
  (1) software - LabVIEW and NOR-motion assistant

  (2) controller - NI PCI-7342

  (3) driver/amplifier - analogue servo AKD Drive

  (4) motor - motor brushless servo AKM

  For the acquisition:
  (1) software - based LabVIEW development systems

  (2) amplifiers or other device - no idea what type on the conditioning of signals

  (3) data acquisition device - no idea what type

  Since I'm a beginner, is - that someone might recommend components (hardware and software) for the control and data acquisition. I'm on a tight budget, so I thankful if someone could help me to recommend components good enough to build my system.

  Thanks for your help.

  At these rates, you will need to run the sensor for the cDAQ.  You can configure the analog output on the Tritex nationally on the position.  There is an adjustable filter that you can set in order to get a clean enough to 300 Hz signal.  When you learn about the Tritex, make sure that let you them know what comms and e/s that you want to use.  If I remember, not all options have worked together.  The analog output may need to be my, but you can put a resistance through the acquisition of input data to get the voltage instead.  I don't remember all the details.  You should really not too much on the Tritex/LabVIEW side.  You will send your movement parameters (beginning of end of race, speed, position, accel, cut), and if you cycle (I believe you) or simply running in a loop.  You could also just be able to use the functions of jog.  When you get close to knowing exaclty what you need, PM me and I'm sure we can work something out with the drivers.  You need only the basics.  In fact, you could probably do this all your movements via digital and analog i/o.

• not able to write the data through data acquisition

  Hello

  In fact, I need to send a code word (text file) from the program matlab through my data acquisition (OR-USB-6215). my program (transmitter.vi [case structure: page2]) attached below has a problem to do the task. whenever I run the program it gives me an error like

  Error-200479 occurred at DAQmx start Task.vi:2

  Possible reasons:

  Measurements: Specified Operation cannot be performed during execution of the task.

  Task name: _unnamedTask<84>

  At the moment I don't see output in my oscilloscope. But, if I highlight my performance I observe my samples on the oscilloscope with the following error message

  200288 error has occurred in the DAQmx write (analog 1-d 1Chan NSamp DBL) .vi:3
  Possible reasons:

  Measurements: Attempted to write a sample beyond the final sample generated. The build is stopped, so the sample specified by the combination of the position and the offset is never available.

  Hi Raja,

  What I did is I moved the 'write DAQmx' outside the while loop. That made the VI in this case is read the file and passing it to a table, and then this table is formatted a waveform to be written to the data acquisition device.

  With respect to the way in which the data is read, I don't change anything, it was based on your original code. A good way to know if you write the correct data is to check the chart view in VI.

  So the question is, is the graphic display showing the good waveform?

  Best regards

  Faris

• Data acquisition inherited Configuration MAX window

  I have LabVIEW 7.1, and Max under the software it shows v8.8 NOR-DAQmx and v7.4.4 NOR-traditional DAQ. When I am developing devices and Interfaces, only from the devices listed OR-DAQmx ppears with the DAQ card (PCI-6221: "Dev1"). The VI I need to ru uses the traditioal DAQ. When I run the VI I get an error message that the jury must be configured. How can I get traditional DAQ to apear in the devices and Interfaces fall down, so I can set the jury? The VI is not easily updated to DAQmx.

  Thanks for any advice.

  Paul

  Hi Paul,.

  The PCI-6221 is a M-series card.  M-series cards have no traditional DAQ driver support.

  Major differences between series E and M series data acquisition devices

• Unknown device named "PCI data acquisition" and signal processing controller in Device Manager

  Greetings,

  Yesterday, my brother, who was running Windows 8.1 Overview on his Asus S400CA Ultrabook fell on a big problem of the NTFS partition corruption that made it impossible to recover through the Refresh Utility Windows 8.1. Given the situation, my brother decided it was better to go back to Windows 8, I had to install Windows 8 on their PCs by using an external DVD drive with a Windows 8 x 64 installer I already buy plenty of detail. The computer never asked me for a product key that I have read is normal in Windows 8 PC now having these embedded in the motherboard. So far an installation smoothly, but he's going to be delicate in the part of pilot facilities. Before you remove the computer I went to the Asus website and did my best to find the specific drivers for my brother's computer and downloaded the key drivers, chipset, audio, intel graphics card, bluetooth, trackpad Wireless LAN, LAN and Asus and installed. I used Device Manager to check that the drivers have been installed and which did not exist. I was able to get most of the drivers installed properly, however, said the Device Manager miss me the pilot of "Data Acquisition and Signal Processing controller PCI. Unfortunately I go to Asus website to see that if I can find the driver however, I can't do this right now.
  Check the attached screenshots for visibility...
  
  
  I also tried to use Windows Update to see if he could find the correct driver and unfortunately it's a dead-end. Because of that I write in this forum to see if someone can point me in the right direction when it comes to this missing driver (and others) indicated in the Device Manager.
  One last thing that I would ask is if I can use a utility like DriverMax to find missing drivers or should I go and install it manually?
  Thank you very much in advance for any help on this matter.
   
  Original title: cannot find drivers for Asus S400CA Ultrabook PCI

  Hi Mike,.

  Please keep us updated on the status of the issue. Please do not hesitate to answer, in case you need help with Windows in the future.

  Good,

  ASUS technical support according to my brother was a bit of a dead end, so I went to another Google search and found the culprit. I was missing the following drivers of ASUS:
  • Intel® dynamic and thermal platform frame driver
  • ASUS Wireless remote control (a driver for you to enjoy the airplane mode (Wireless) On / Off)
  The first pilot took care of the Acquisition of ICP data and Signal Processing controller and all but one of the unknown devices. Finally, the other took care of the last unknown device in Device Manager.
  I never thought that ASUS would use this a strange name for their driver because these names are extremely misleading.
  Other than that, I can finally say with certainty that the computer of my brother is back in business, and I can call this comprehensive process of restoration of Windows 8.
  Thanks for any assistance to Zaki J, I appreciate much all advice through this process!

• Pavilion TS 17-g099nr: PCI Data Acquisition and processing of the Signal Windows 10 x 64 controller driver

  Hi, it is impossible for the moment to install the driver for PCI Data Acquisition and Signal Processing.

  I downloaded the driver from Intel, and it did not work... I found a version of this site for windows 8.1 unupdated and it does not work.

  A little help?

  Thank you!

  Hello:

  It could be one of two different drivers.

  Try this one first, and then restart the PC.

  This package contains the Intel Chipset Installation utility. This utility allows the operating system to show the correct name for the Intel hardware that is installed in the Microsoft Windows Device Manager. This package is provided for the laptop models running a supported operating system.

  FTP://ftp.HP.com/pub/SoftPaq/sp75501-76000/sp75561.exe

  If this does not work, try this one...

  This package contains the driver which allows Intel platform dynamic and thermal firmware setting. Intel platform dynamic and thermal environment information system temperature and power use for the thermal protection of the system to work properly. This package is provided for the laptop models running a supported operating system.

  FTP://ftp.HP.com/pub/SoftPaq/sp75501-76000/sp75506.exe

• 15 - ac122tu: PCI of Data Acquisition and the controller driver of laptop HP 15-ac122TU signal processing

  Hi team,

  I just install windows 7 edition integral and peripheral Bluetooth windows 8.1 is not be detectable, when I search for problem that I came across this PCI data acquisition and Signal Processing controller driver is missing and a unknown device driver missing shownup in my result of troubleshooting. Please help me

  Please find the screenshot for your reference

  Thank you

  

  Hello:

  See if these drivers work...

  CQI PCI controller:

  This package contains the driver which allows Intel platform dynamic and thermal firmware setting. Intel platform dynamic and thermal environment information system temperature and power use for the heat of the system
  protection to work properly. This package is provided for the laptop models running a supported operating system.

  File name: sp71638.exe

  Bluetooth:

  This package contains the installation package driver for Realtek bluetooth in the laptop models running a supported operating system.

  File name: sp71288.exe

  Unknown dev:

  This package provides the HP 3D DriveGuard software (HP ProtectSmart Hard Drive Protection) for the laptop models running a supported operating system. HP 3D DriveGuard software protects the drive hard by parking the heads if cell phone accidentally falls, or is suddenly struck by another object.

  File name: sp71811.exe

• LeCroy Waverunner 640Zi - Data Acquisition

  Hello... I'm trying to set up my oscilloscope waverunner with LabVIEW SignalExpress for data acquisition.

  I took the steps so far:

  1 pulse generator hooked to scope of signal generation

  2 USB scope to the installed computer with LabView

  3 downloaded lecroyscope driver 3.2.9 - x 64

  I turn on the scope and plug in the USB to the computer and SignalExpress begins.

  a. start by using data acquisition

  b. Add step/aquire signal / IVI aquire / IVI brought aquire

  c. create new IVI session... resources descriptor (I choose my USB device ' USB0::0x05FF:0 x 1023: 2812N61507:INSTR '), I select the right driver (lcscope), and I do not click enable simulation data, press ok
  d. I still receive configuration errors

  e. did the research... some forum said goto MAX, find drivers and uncheck the Cache and the exchange of check

  f. attempt to initialize... always get config errors.

  g. return to MAX... change to simulate with specific driver.

  h. initialization works... NO errors, BUT no data are acquired.

  Help, please!

  Hello

  Sorry to jump in if I was out of the country for a while and am still catching things in my office.

  I think you are looking for someone to say yes, "you can connect to the scope with NOR-MAX and VISA, and here's how interactive tool do"

  A few things:

  LabVIEW for XStream extended driver is the right one.  It works with all the TeledyneLeCroy Windows based scopes.

  As I see has already been noted. (I'll give Kudos soon), the scope of application must be configured to use interface USBTMC.  To do this, go to the drop down Utitlites on the scope menu and select "utilities configuration... '. "in the tabs that appear at the bottom of the screen, select the 'Remote' tab and make sure that the interface type is set to USBTMC.  This will also show you the VISA resource (I see it in the title of the image of VISA interactive tool indicated in a previous post).

  Once this field is selected, the PC should detect the USB connection and install the device. (you can see in your device manager as a Test of USB and the measurement device):

  

  Once this is done, you can then enter the NOT-MAX and it will detect and display resources.  You can now communicate with the device:

  

  If you have problems, do not hesitate to give me a call and I'm happy to walk through it over the phone.

  Kind regards

  Leonard Brown
  Technical sales engineer
  Teledyne LeCroy
  1-800-553-2769

• Laptop HP, sn 5CG5231VT5: PCI Data Acquisition and Signal Processing controller driver

  I installed win 10 x 64 on my HP laptop, but miss me the:

  -INC of Data Acquisition and processing of Signal Controller driver.

  -Intel Atom (TM) /Celeron (R) /Pentium (R) processor Intel DPTF thermal device framework - 3400

  -Unknown device

  Can you please help?

  FOR INFO:

  I already install the latest Chipset Intel 10.0.27.0, and

  Download all the drivers on the HP support assistant page.

  Hello:

  See if this driver works...

  This package contains the driver which allows Intel platform dynamic and thermal firmware setting. Intel platform dynamic and thermal environment information system temperature and power use for the thermal protection of the system to work properly. This package is provided for the laptop models running a supported operating system.

  File name: sp71262.exe

• PCI Data Acquisition and Signal Processing controller driver

  I installed win 8.1x64 on my HP Probook 450 G2, but miss me the driver of PCI Data Acquisition and Signal Processing controller.

  Can you please help?

  Thank you

  Leontina

  Hello:

  Please see if installing the Intel Chipset driver installs this device.

  https://Downloadcenter.Intel.com/Detail_Desc.aspx?DwnldID=20775 & lang = eng & ProdId = 816

• Z600 Workstation: workstation Z600 missing of pci data acquisition and signal processing controller driver

  I just installed Win7 Pro x 86 on my Z600 workstation.  It was an upgrade to Windows XP Pro.  I'm missing the driver for PCI Data Acquisition and processing of the Signal and Hardlock USB 1.02 controller in Device Manager.  Can someone help me find these drivers.  I looked on the page of Support/Drivers for this model, but could not find anything.

  Hello

  You can get assistance on the HP Enterprise Business Forum since you have a professional worktsation.

• 15 - r235ne: SM bus controller / IBD DATA Acquisition and Signal Processing controller

  Hello team

  I am facing problem in finding the right driver for material below.

  1 SM bus controller

  2 IBD DATA acquisition and Signal Processing controller

  kindly help

  concerning

  NASIR

  Hi, Nguyen:

  Download and install the Intel chipset installation utility and restart the PC.

  The 2nd driver down on the left is the automatic installation file.

  https://Downloadcenter.Intel.com/download/20775/Intel-chipset-device-software-INF-Update-utility-?product=1145