User profile service failed to load

Similar Questions

• I created a new Admin account and when I went to her, I got the message: "The service user profile Service has no logon. The user profile Service failed to load.

  I created a new Admin account and when I went to her, I got the message:

  "The service user profile Service has no logon.  The user profile Service failed to load.

  What's up with that?

  Hello

  References to Vista also apply to Windows 7.

  You can try to fix it with Safe Mode - repeatedly press F8 as you bootup. The ADMIN account in trunk
  Mode has no default password (unless someone has changed the password so it should be available).

  Some programs such as the updated Google (if you added the toolbar Google, Chrome or Google Earth)
  has been known to cause this problem.

  Error message when you log on a Windows Vista-based or Windows 7 using computer a
  Temporary profile: "the user profile Service has no logon. Unable to load the user profile.
  http://support.Microsoft.com/kb/947215

  Difficulty "the user profile Service has no logon. User profile cannot be loaded. "Error in Windows 7
  http://www.SevenForums.com/tutorials/186131-user-profile-service-failed-logon-user-profile-cannot-loaded.html

  How to fix error "your user profile was not loaded correctly! You have been connected with a
  temporary profile. "in Vista & Windows 7.
  http://www.Vistax64.com/tutorials/135858-user-profile-error-logged-temporary-profile.html

  BE VERY CAREFUL IF YOU USE THIS ONE:

  DO NOT USE THE ACCOUNT HIDDEN ON A DAILY BASIS! If it corrupts you are TOAST.

  How to enable or disable the built-in Windows 7 Administrator account
  http://www.SevenForums.com/tutorials/507-built-administrator-account-enable-disable.html

  Use the hidden administrator account to lower your user account APPLY / OK and then lift it to ADMIN.
  This allows clear of corruption. Do the same for other accounts if necessary after following the above message.

  You can use the hidden - administrator account to make another account as ADMINISTRATOR with password even
  (or two with the same password) use a test or fix the other.

  You can run the Admin account hidden from the prompt by if necessary.

  How Boot for Windows 7 System Recovery Options or use a Windows 7 boot disk.
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  What are the system recovery options in Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  If you cannot access your old account, you can still use an Admin to migrate to another (don't forget
  always leave to an Admin who is not used except for testing and difficulty account).

  Difficulty of a corrupted user profile
  http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspx

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Get the error message "failure to log - on, the user profile user profile Service failed to load.

  Original title: I downloaded 17 Win. 7 pro updates Wednesday, June 15

  Since this update was completed, I was unable to get into my computer; It goes through the usual startup routine, then it goes straight to the 'return - sleep' emblem that I usually just click on (when the computer is back to sleep, not a start-up), and the answer I get is "failure to log - on, cannot load user profile user profile Service. I sure as hell don't want to lose all my data with a fresh 7 - Pro disc. Someone at - it ideas? I swear I'll hold all Microsoft Updates for a few months before installing again. I also had problems with updates of March 2015. Thank you; Croft * address email is removed from the privacy * P.S. I use my old X.P. to connect again.

  Hello

  Thanks for posting your question on the Forums of community of Microsoft.

  According to the description, you receive error message "the user profile service has no log on." User profile could not be found.

  I would be grateful, if you can provide us with the following information to help us better understand the question?

  • Did you the latest changes on your system prior to this problem?

  I suggest you follow the advice given by Jayant Narang replied the August 14,2014 from the link given below and check.

  Reference:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-security/the-user-profile-service-failed-the-log-on-user/77768431-FAEC-4DA8-b2cb-ddd95fb2e97d

  Hope this information is useful. Please let us know if you need help with Windows.

• Tried to open a session has message USER PROFILE SERVICE failed to open a session, the user profile loaded Onlyon

  Computer was working fine last night. AFTE rtalking on Skype, stop computer and now today this message keeps coming up when you try to connect to computer

  Computer was working fine last night. AFTE rtalking on Skype, stop computer and now today this message keeps coming up when you try to connect to computer

  Go to Safe Mode
  http://www.Vistax64.com/tutorials/123496-safe-mode.html

  If you can log in to your account administrator in safe mode...
  Do a system restore. Choose a date where you did not have this problem as your restore point.

  If you are unable to log in to your account administrator in safe mode...

  You see another tool counts next to yours? Yes, if your built-in Administrator account > by default, there no password > login and do a system restore > choose a date where you did not have this problem as your restore point.

  If you can't do or of what above, see if this tutorial will help:

  http://support.Microsoft.com/kb/947215

  or this tutorial

  http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.html

• The user profile Service failed to connect. User profile cannot be loaded.

  The user profile Service failed to connect. User profile cannot be loaded.  Plus all the other user 5 passwords no longer work nor password records or profiles comments or PCL. Under Safe Mode, I am forced to reactivate the Vista operating system before use but cannot mode without failure. How can I get around this block?

  I think you should check for malware. You will not have the particular malware that is mentioned in the following Article, but the Article describes in great detail to try to regain control of the computer. If regain you control, we hope, you can use system restore to go back ahead before the problem arose.

  It would be useful to know what anti-virus software has been installed on the computer, as the ability to restore the system to function properly may be seriously jeopardized if you use Norton and some other software.

  http://www.myantispyware.com/2011/02/21/how-to-remove-Internet-Security-Essentials-virus/

• Error when you try to connect to the account of user: the user profile service failed the lied/user cannot load profile

  Im trying to connect to my own acc on my computer, but it says 'the user profile service failed the lied/user cannot load profile' im using an accout comments I had set up for my sister and that I keep reciving a message saying that Windows Explorer as stoped working so I can't open any doc.music. pictures or whatever it is im in internet using foxfire that I installed it on another acc please help I don't know how to connect to m trying to connect to my own acc on my computer, but it says 'the user profile service failed the lied/user cannot load profile' im using an accout comments I had set up for my sister and that I keep reciving one message saying that stoped working so I can't open Windows Explorer all doc.music. pictures or whatever it is im in internet using foxfire that I installed it on another acc please help I don't know how to connect to my admin accmy admin acc

  Hello

  You can try to fix it with Safe Mode - repeatedly press F8 as you bootup. The ADMIN account in trunk
  Mode has no default password (unless someone has changed the password so it should be available).

  Some programs such as the updated Google (if you added the toolbar Google, Chrome or Google Earth)
  has been known to cause this problem.

  Error message when you log on a Windows Vista-based or Windows 7 using computer a
  Temporary profile: "the user profile Service has no logon. Unable to load the user profile.
  http://support.Microsoft.com/kb/947215

  How to fix error "the user profile Service has no logon. User profile cannot be loaded. »
  http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.html

  How to fix error "your user profile was not loaded correctly! You have been connected with a
  temporary profile. "in Vista
  http://www.Vistax64.com/tutorials/135858-user-profile-error-logged-temporary-profile.html

  BE VERY CAREFUL IF YOU USE THIS ONE:

  DO NOT USE THE ACCOUNT HIDDEN ON A DAILY BASIS! If it corrupts you are TOAST.

  How to enable or disable the real built-in Administrator account in Vista
  http://www.Vistax64.com/tutorials/67567-administrator-account.html

  Use the Admin account hidden to lower your user account APPLY / OK then wear again to
  ADMIN. This allows clear of corruption. Do the same for other accounts if necessary after the
  above message.

  You can use the hidden - administrator account to make another account as an ADMINISTRATOR with your same
  password (or two with the same password) use a test or difficulty to another.

  You can run the Admin account hidden from the prompt by if necessary.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  If you cannot access your old account, you can still use an Admin to migrate to another (don't forget
  always leave to an Admin who is not used except for testing and difficulty account).

  Difficulty of a corrupted user profile
  http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspx

  I hope this helps.

• Cannot log on to the profile following messages "user profile service failed og on.» User profile cannot be loaded.

  When you try to connect to my Vista account download the above, m essage. Other accounts work, but as is the VDP administrator who does not open a session cannot make changes.

  ·                        Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.
  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not work:

  ·                        http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.html

  See if the information in the above tutorial will help you.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspx

  Difficulty of a corrupted user profile

  After creating the profile, you can copy the files from the existing profile. You must have at least three user accounts on the computer to perform these operations, including the new account that you created.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://support.Microsoft.com/kb/947242

  A temporary profile is loaded after you connect to a Windows Vista-based system

  See you soon.

  Mick Murphy - Microsoft partner

• Retrieve the user profile for a new user after user profile Service failed and could not be loaded

  I use Windows Vista Home Premium operating system.

  I wasn't able to log onto my user;  I searched online for an answer and advise him to create another user - I had 'Admin' status with the original user.

  I followed the following instructions:

  http://support.Dell.com/support/topics/global.aspx/support/DSN/en/document?c=us&CS=19&docid=39CC797DE6882CB6E040A68F5B285C29&l=en&s=DHS

  According to these instructions, I've logged on the account current and open a session on the new user account.  However, all my documents, pictures, music, files, office, Microsoft Office Suite, Microsoft Outlook Email, etc. have disappeared!

  I not created it of new files or documents under the new user in the fear that it crushes everything and help restore everything back to its original state.

  When I performed a search of the system / "C: drive", none of the documents or files have been found.

  How to restore these things, especially my photos?  Or, how to restore the original user?

  Any help you give me for this problem will be greatly appreciated.

  original message: error message: "could not load user profile and user profile Service failed". Made a function to create a new user, but all my files, pictures, music, desktop icons and other stuff are GONE AND I can't FIND them ANYWHERE!

  Hello

  Your data and files are still there in the C:\Users\Your user name where C: is the drive where
  user profiles are stored.

  You can try to fix it with Safe Mode - repeatedly press F8 as you bootup.

  Some programs such as the updated Google (if you added the toolbar Google, Chrome or Google
  Earth) has been known to cause this problem.

  How to fix error "the user profile Service has no logon. User profile cannot be loaded. »
  http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.html

  How to fix error "your user profile was not loaded correctly! You have been logged on with
  a temporary profile. "in Vista
  http://www.Vistax64.com/tutorials/135858-user-profile-error-logged-temporary-profile.html

  BE VERY CAREFUL IF YOU USE THIS ONE:

  DO NOT USE THE ACCOUNT HIDDEN ON A DAILY BASIS! If it corrrups you are TOAST.

  How to enable or disable the real built-in Administrator account in Vista
  http://www.Vistax64.com/tutorials/67567-administrator-account.html

  Use the Admin account hidden to lower your user account APPLY / OK then wear again to
  ADMIN. This allows clear of corruption. Do the same for other accounts if necessary after the
  above message.

  You can use the hidden - administrator account to make another account as an ADMINISTRATOR with your same
  password (or two with the same password) use a test or difficulty to another.

  You can run the Admin account hidden from the prompt by if necessary.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  If you cannot access your old account, you can still use an Admin to migrate to another (don't forget
  always leave to an Admin who is not used except for testing and difficulty account).

  Difficulty of a corrupted user profile
  http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspx

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• User profile Service failed: the user profile Service service has no logon. User profile cannot be loaded

  I have another computer.   I turned it on and when I typed my windows password, I received the following message: the user profile service service has no logon.  User profile cannot be loaded. Service user profile Service has no logon.  User profile cannot be loaded.  I use Windows 7 Professional.  I don't have a password reset disk.  How can I get?

  Hello

  You can try to fix it with Safe Mode - repeatedly press F8 as you bootup. The ADMIN account in trunk
  Mode has no default password (unless someone has changed the password so it should be available).

  Some programs such as the updated Google (if you added the toolbar Google, Chrome or Google Earth)
  has been known to cause this problem.

  Error message when you log on a Windows Vista-based or Windows 7 using computer a
  Temporary profile: "the user profile Service has no logon. Unable to load the user profile.
  http://support.Microsoft.com/kb/947215

  How to fix error "the user profile Service has no logon. User profile cannot be loaded. »
  http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.html

  How to fix error "your user profile was not loaded correctly! You have been connected with a
  temporary profile. "in Vista
  http://www.Vistax64.com/tutorials/135858-user-profile-error-logged-temporary-profile.html

  BE VERY CAREFUL IF YOU USE THIS ONE:

  DO NOT USE THE ACCOUNT HIDDEN ON A DAILY BASIS! If it corrupts you are TOAST.

  How to enable or disable the built-in Windows 7 Administrator account
  http://www.SevenForums.com/tutorials/507-built-administrator-account-enable-disable.html

  Use the hidden administrator account to lower your user account APPLY / OK and then lift it to ADMIN.
  This allows clear of corruption. Do the same for other accounts if necessary after following the above message.

  You can use the hidden - administrator account to make another account as ADMINISTRATOR with password even
  (or two with the same password) use a test or fix the other.

  You can run the Admin account hidden from the prompt by if necessary.

  How Boot for Windows 7 System Recovery Options or use a Windows 7 boot disk.
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  What are the system recovery options in Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  If you cannot access your old account, you can still use an Admin to migrate to another (don't forget
  always leave to an Admin who is not used except for testing and difficulty account).

  Difficulty of a corrupted user profile
  http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspx

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Unable to get the administrator account, receive the error such as the user profile service failed logon. User profile could not be loaded. "

  Original title: "the user profile service has no logon. User profile could not be loaded"and admin password will not work

  I had this problem came several times before but it always correct itself without any intervention from myself. Now, even after restarting the computer several times I can not directly connect to my main Administrator profile. I have another profile without administrative privileges already done so I could at least use my computer, but only with limited permissions. When I try to do something to solve the problem, as the registry change, I'm prompted to enter the administrator password. I enter the password and the alert box goes, and nothing happens. Enter the password seems doing nothing, except the aknowledge the password is correct (it warns me when I entered a wrong password so I know it's no doubt receiving data). DOoes anyone know how to fix this? The computer works relatively well recently and have no idea of what decoration could have happened to cause such a mistake that bothers.

  Hello

  This worked for me, try allowing the default Administrator account, the steps are in the following link
  http://somanytips.com/Windows-Vista7-the-user-profile-service-failed-the-logon-user-profile-cannot-be-loaded/
  I hope this will help!

• Satellite L855 - 11 p: Win 7 - user profile Service failed to connect

  Can not connect. The message reads user profile Service failed to connect. User profile cannot be loaded"

  Y at - it a bypass key?
  Ideas please.

  Fine machine when I logged out/shut down last night but can not pass this message today.

  Hello

  Please take a look here in this Microsoft Knowledge base article:

  [You receive a "the user profile Service has no logon error message:"] http://support.Microsoft.com/kb/947215]

  There are different ways to fix it.

  Your comments would be appreciated.

• My user account will not open a session. message, said the user profile service failed.

  Two days ago, I try to connect my messgae of acct user popped up of service user profile service failed to connect. Have the other 3 acct and they connect without any problems.  How can I fix it?

  Hello

  These methods should help for Windows 7 or Vista.

  References to Vista also apply to Windows 7.

  You can try to fix it with Safe Mode - repeatedly press F8 as you bootup. THE ADMIN
  Safe Mode account has no default password (so unless someone changed
  the password should be available).

  Some programs such as the Google Updater (if you've added the Google toolbar,
  Chrome or Google Earth) has been known to cause this problem.

  Error message when you log on to a Windows Vista-based or Windows 7
  computer by using a temporary profile: "the user profile Service has no logon.

  Unable to load the user profile.
  http://support.Microsoft.com/kb/947215

  Difficulty "the user profile Service has no logon. User profile cannot be loaded. "Error in Windows 7
  http://www.SevenForums.com/tutorials/186131-user-profile-service-failed-logon-user-profile-cannot-loaded.html

  How to fix error "the user profile Service has no logon. Could not load user profile. "in Vista & Windows 7.
  http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.html

  How to fix error "your user profile was not loaded correctly! You have visited
  logged on with a temporary profile. "in Vista & Windows 7.
  http://www.Vistax64.com/tutorials/135858-user-profile-error-logged-temporary-profile.html

  BE VERY CAREFUL IF YOU USE THIS ONE:

  DO NOT USE THE ACCOUNT HIDDEN ON A DAILY BASIS! If it corrupts you are TOAST.

  ----------------------------------------------------------------------------------------------------------

  For Windows 7:

  How to enable or disable the built-in Windows 7 Administrator account
  http://www.SevenForums.com/tutorials/507-built-administrator-account-enable-disable.html

  Use the hidden administrator account to lower your user account APPLY / OK then
  Raise it to ADMIN. This allows clear of corruption. Do the same for other accounts
  If necessary after following the above message.

  You can use the hidden - administrator account to make another account as an ADMINISTRATOR with
  your password even (or two with the same password) use a test or difficulty to another.

  You can run the command Admin account hidden from the command prompt
  from there if necessary.

  How Boot for Windows 7 System Recovery Options or use a Windows 7 boot disk.
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  What are the system recovery options in Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  ----------------------------------------------------------------------------------------------------------

  For Vista:
  
  How to enable or disable the real built-in Administrator account in Vista
  http://www.Vistax64.com/tutorials/67567-administrator-account.html

  Use the hidden administrator account to lower your user account APPLY / OK then
  Raise it to ADMIN. This allows clear of corruption. Do the same for other accounts
  If necessary after following the above message.

  You can use the hidden - administrator account to make another account as an ADMINISTRATOR with
  your password even (or two with the same password) use a test or difficulty to another.

  You can run the command Admin account hidden from the command prompt
  from there if necessary.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  What are the system recovery options in Windows Vista?
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

  How to create a Vista - free methods recovery disk
  http://www.Vistax64.com/tutorials/141820-create-recovery-disc.html

  ---------------------------------------------------------------------------------------------------------

  If you can't access your old account you can still use an Admin to migrate to one
  new (remember to always leave an account Admin who is not used except)
  to test and difficulty).

  Difficulty of a corrupted user profile
  http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspx

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Unable to connect to the laptop, receive error message "the user profile service failed.

  can not connect to the computer

  * original title - I can't connect on the laptop when I put in password says the USER PROFILE SERVICE FAILED THE LAGOON AND DO CAN NOT BE LOADED a *.

  Hi vincentbyrne

  
  What operating system is installed on the computer?

  You can refer to the link below and use the provided steps to identify the installed operating system.

  http://Windows.Microsoft.com/en-us/Windows7/help/which-version-of-the-Windows-operating-system-am-i-running

  
  If you are using Windows Vista or Windows 7 based computer you can see Microsoft article provided below and check if the measures help -.

  http://support.Microsoft.com/kb/947215

   

  I hope this helps.

• User profile service failed

  On another one of my computers, I get the message "THE USER PROFILE SERVICE has NO logon. UNABLE to LOAD the USER PROFILE"when I try to open a session.  I can log on using a different user account, but this option does not allow me to create a new user account.  The computer the problem using VISTA.

  Hello

  You can try to fix it with Safe Mode - repeatedly press F8 as you bootup. The ADMIN account in trunk
  Mode has no default password (unless someone has changed the password so it should be available).

  Some programs such as the updated Google (if you added the toolbar Google, Chrome or Google Earth)
  has been known to cause this problem.

  Error message when you log on a Windows Vista-based or Windows 7 using computer a
  Temporary profile: "the user profile Service has no logon. Unable to load the user profile.
  http://support.Microsoft.com/kb/947215

  How to fix error "the user profile Service has no logon. User profile cannot be loaded. »
  http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.html

  How to fix error "your user profile was not loaded correctly! You have been connected with a
  temporary profile. "in Vista
  http://www.Vistax64.com/tutorials/135858-user-profile-error-logged-temporary-profile.html

  BE VERY CAREFUL IF YOU USE THIS ONE:

  DO NOT USE THE ACCOUNT HIDDEN ON A DAILY BASIS! If it corrupts you are TOAST.

  How to enable or disable the real built-in Administrator account in Vista
  http://www.Vistax64.com/tutorials/67567-administrator-account.html

  Use the Admin account hidden to lower your user account APPLY / OK then wear again to
  ADMIN. This allows clear of corruption. Do the same for other accounts if necessary after the
  above message.

  You can use the hidden - administrator account to make another account as an ADMINISTRATOR with your same
  password (or two with the same password) use a test or difficulty to another.

  You can run the Admin account hidden from the prompt by if necessary.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  If you cannot access your old account, you can still use an Admin to migrate to another (don't forget
  always leave to an Admin who is not used except for testing and difficulty account).

  Difficulty of a corrupted user profile
  http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspx

  I hope this helps and happy holidays!

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• User profile service failed Logon of a and I've invited account

  Okay, so here's the problem, my only administrative account I can't log in because the logon user profile Service failed. The only account I have is the guest account. I can't do anything with this account because it is not an administrator account. I understand the process of setting the logon service is deleting the account that does not work. If that's what the process of HKEY_LOCAL_MACHINE is the case, how can I make another administrative account with only a guest account and I hope to be able to recover some files I have on my administrator account. Please, help me! PS - Can - explain you the process of removing the SID? Thank you very much! In addition, what should I do if I tried the system restore and nothing has worked.

  This error can usually be fixed by following the steps below. All this requires a certain level of computer skills. You know better and that take the machine to a competent local computer tech (not a type of BigComputerStore/GeekSquad place) is the best solution for you.

  1 log on to a different user account with administrative privileges. If you neglected to make an account additional administrative steps 2-3. Otherwise, continue to step 4. See also General information on setting up user accounts in Vista at the end of this post.

  2 in Mode safe boot. This, by repeatedly pressing the F8 key as the computer starts. That you will get to the menu on the right where you can use your arrow key to select Mode safe [Enter]. The built-in Administrator account is disabled by default in Vista. However, if no other administrative accounts exist on the system it can be activated. If this is the case, you will see an icon for the administrator on the homescreen mode without failure. Login to the administrator.

  3 If you don't see the icon for the administrator mode safe account, then the built-in Administrator account is always disabled so you will need to work more. If you have an installation of Vista DVD (not a recovery DVDs), you can start the system with it. Select the default language, then select "repair your computer". Then select "Command Prompt". At the command prompt, type:

  NET user administrator / Active: Yes [Enter]

  [Note: do not enter the brackets!]

  If you do not have a Vista installation DVD (only have a recovery disk), the computer mftr. may have given you the option to repair Vista (not a system recovery!) system in the diagnostic menu. This menu of diagnosis is the same one where you can choose Safe Mode.  Or you can do a repair file Vista bootable DVD in this link:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Note: All the Neosmart recovery disk downloads are torrent files. There is a good explanation of the torrent on the site Web of Neosmart files. You will need a torrent as muTorrent client to get the files. Torrent client will download the .iso file with which to create the bootable DVD. You will need the third-party burning software such as Nero, Roxio or the free ImgBurn (www.imgburn.com ) to burn the .iso image image file, not in the form of data.

  Now remove the rescue CD/DVD, you have done, reboot Windows and log on to the built-in Administrator account, you enabled.

  4. try a system restore to when things worked. If you can log in to your user account, you are finished. Otherwise, continue to step 5.

  5. the critical files are under % systemdrive%\users\user-account\ntuser. The ntuser.dat file is actually a registry hive. Run Regedit high and select HKEY_USERS and "load hive" in the menu. Now, go to:

  HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\ProfileList

  There is a line for each profile. If a profile is bad, check:

  (a) that the name of the key does not stop in ".bak" (remove .bak If it)
  (b) that the RefCount value is 0 (change it if it is different)
  (c) that the State value is 0 (change if different)

  Make the necessary changes, close Regedit and try to connect as this user.

  6. If that doesn't solve your profile, it is corrupt. When you do that, you should make a new Standard user account and copy your data to it. Do not delete the old account until you have recovered data you need!

  Once everything works, go to the additional administrative account you will be made by the suggestions below and disable the administrator account integrated yet for security reasons:

  Start Orb > Search box > type: cmd
  When cmd appears in the above results, right-click and choose "Run as Administrator" [OK]. Now, you will get the command prompt. At the command prompt, type:

  NET user administrator / active: No. [Enter]

  Exit the command prompt.

  General recommendations for creating users in Vista

  You absolutely don't want to have only one user account. As XP and all the other modern operating systems, Vista is a multi-user system with integrated system of accounts as default Administrator and comments. These accounts should be left alone because they are part of the structure of the operating system.

  In particular, you do not want one account user with administrative privileges on Vista because the administrator account integrated (normally only used in emergencies) is disabled by default. If you use as an administrator for your daily work, and this account is corrupt, things will be difficult. It is not impossible to activate the built-in administrator to rescue things, but it can be more work you want to do. Better not to get into a bad situation at first.

  The user account that is for your daily work must be a Standard user, with the extra administrative user (call it something like 'CompAdmin' or 'Tech' or similar) only it for elevation purposes. As a user Standard is recommended for security reasons and will help protect your computer against infections. After you have created "CompAdmin", connect to it and change your normal user account Standard. Then log on to your regular account.

  If you want to go directly to the desktop and ignore the Welcome screen with the icons of the user accounts, you can do this:

  Start Orb > Search box > type: netplwiz [Enter]
  Click continue (or provide an administrator password) when you are prompted by UAC

  Uncheck "users must enter a user name and password to use this computer". Select a user account to connect automatically by clicking on the account you want to highlight and press OK. Enter the password for this user account (when it exists) when you are prompted. Leave blank if there is no password (null).
  MS - MVP - Elephant Boy computers - don't panic!