Using the drive 100% running 8.1 Win

Help me please,

What can I do on this 100% disk usage?
It is going on all the time... I added the photo, so that you can see.

Sometimes he says that the system is the problem, sometimes programs like utorrent or firefox,
Other times it's simply nothing (!), but it's always 100% usage...

[https://www.dropbox.com/s/m9ncihihvlnf1dw/Untitled2.png?dl=0]
[https://www.dropbox.com/s/lafx62833vnwps5/Untitled.png?dl=0]

I have a brand new computer:

Processor: Intel Core i5 - 4200 M CPU @ 2.50 GHz
1 video card: NVIDIA GeForce 710 M (Total dedicated memory - 1.0 GB, memory - 2.9 GB)
2 video card: Intel(r) HD Graphics 4600 (Total dedicated memory - 1.0 GB, memory - 2.9 GB)
Memory: 4.0 GB
Operating system: Microsoft Windows 8.1, 64-bit
Size: GB 687,8

You can stop the background process which is responsible for the use of the HARD drive.
Of course the processes running in the background, access data (reading / writing), and therefore the use of the HARD disk increases dramatically.

For example, you installed a client utorrent... This tool sharing the beween of data using the internet connection and so the HARD drive is busy

Tags: Toshiba

Similar Questions

  • Using the drive 100%

    Sometimes when you use google chrome, the use of the disc my laptop becomes 100% and it's starting to get bad. Help, please.

    I have Windows 8 Pro installed on the laptop to HP 1000-1140TU.

    OK, I have flashed the BIOS to the previous pversion and reset the CMOS by default, and all is fine now. Looks like the problem has been caused by updating the BIOS, which affected half of the RAM reserved hardware memory and resulted in frequent paging...

  • using the drive 100% pc slowdown

    Hello

    Recently, I had a few problems with viruses, so I installed AVG in addition to inadequate work of Windows Defender. I left my pc fully analyze and

    deeply. You can see their report here:

    .

    But these measures did not effect anything. The problems (which began even before that AVG has come) are always the same:

    -the pc starts very slowly...

    -J' got the ATTEMPT_SWITCH_FROM_DCP error once while looking upward

    -the disc is "overloaded" for 10 minutes every time I opened the laptop. In the Task Manager, it says busy with very low values MB/s to 100%.

    -When I close the laptop, the system does not go on standby mode, but abandoned.

    can someone help me?

    Thank you!

    Hi Isaak,

    Thanks for posting your question on the Microsoft Community.

    It is likely that this problem is caused by a corrupted or inconsistent application. I suggest that you restart your computer in a clean boot and check if the problem resolves.

    How to perform a clean boot in Windows
    http://support.Microsoft.com/kb/929135/en-us

    After troubleshooting, refer to the section «How to reset the computer to start normally after a boot minimum troubleshooting»

    Hope this information was useful. Please answer with the results and if you need help or have questions about windows, we will be happy to help you.

  • Using the drive almost always at 100% at the start and sometimes at other times

    Recently, my laptop seemed particularly overwrought, even when executing threads. Whenever I start it (and also sometimes at random so that I use for light work), it is much slower than it has been in the past, and when I check the tast Manager, it says that the disc is in 90 to 100% almost every time. So I watch programs using the floppy and almost all of them use it with a rate of 0 MB/s, and all other use at a fairly slow pace. I know it's normal for notebook computers to slow down over time (mine is a little over a year old), but I wonder if it is an expected behavior. I find it odd that the drive is the treatment so furiously, but it seems to me that no program is really use it. I enclose below, pictures of my complete task manager a few minutes after starting.

    My processor is an Intel i7-4700MQ CPU @ 2.40 GHz and I have 12 GB of RAM.

    @MirandaSnow ,

    Hello and thanks for the display on the HP support forums.  What you have going here is not a hardware problem.  It is a common problem with windows 8.1 and an update.

    Here are some links that I could find that should help you with this problem.

    Use of the disk Windows 8.1 100%

    Windows 8 guard slows to grip and 100% use of the disk.

    How to fix: problem of its use for the drive 100% Windows 8

    Let me know how things are going with this.

    Thanks again for posting and have a great day.

  • RN102 - please remove inactive volumes in order to use the drive - data loss

    ReadyNas 102, 1 x 1 TB of disk (in 2nd driving position), belonging to 10 days, using 6.2.5

    I copied perhaps 25 data DVD disk (1 volume, through about 4 servings). I have lost the network connection to the NAS server, could not get the sin to meet switch & finally upluged the power from the back, after a reboot that worked was & when reconnecting, I note ALL my data drive disappeared. No matter what I do with the power, I shouldn't be able to have this catastrophic failure.

    If I go to Volumes, it shows the volume, with a red dot in the upper left, with the data and free are two 0.

    also a ball - please remove inactive volumes in order to use the drive. Disk #2.

    If I go to actions it says: no volume or USB drives. It is recommended to create a volume before you set up other...

    If I had 2 drives (copies of each other) would I still lost all of these data. It seems that the reliability of disc is not my main concern, but the speaker.

    I've never had a pc lose all his data by car, make it look training crashed as the s/w me invites to use it. It looks like the o/s meta data, manage the contents of the disk are broken down.

    Is this code issues I may be courses?

    You have the USB key with the encryption key connected to the NAS Server? The key must be plugged to the volume mounted power.

    Looks like you will need to contact support.

  • No internet after using the Envy 100

    Whenever I use the Envy 100 (or to be more precise: when the urge got a Wi - Fi connection) I lose internetconnectivity. But only after I finish a session to my router (Linksys WRT610N). When I turn off the router and the next time, it cannot connect to my internetmodem (Linksys AM200) at all. WiFi is in place, but I have only local access, apparently the router cannot connect to my modem (which indicates both the CABLE with the router as the to Internet is up.)

    This only happens after the sessions where I used the desire, otherwise everything is OK. During these sessions, there is no problem, only after the start a new. The only way to restore the connection is reset my hard router and reconfigure.

    BTW. I am one of the users who are unable to get a connection to the webapps desire, but there work ePrint - that is another thread on this forum. Not sure if the two problems are or are not connected.

    Any help or pointers?

    herstil wrote:

    Whenever I use the Envy 100 (or to be more precise: when the urge got a Wi - Fi connection) I lose internetconnectivity. But only after I finish a session to my router (Linksys WRT610N). When I turn off the router and the next time, it cannot connect to my internetmodem (Linksys AM200) at all. WiFi is in place, but I have only local access, apparently the router cannot connect to my modem (which indicates both the CABLE with the router as the to Internet is up.)

    This only happens after the sessions where I used the desire, otherwise everything is OK. During these sessions, there is no problem, only after the start a new. The only way to restore the connection is reset my hard router and reconfigure.

    BTW. I am one of the users who are unable to get a connection to the webapps desire, but there work ePrint - that is another thread on this forum. Not sure if the two problems are or are not connected.

    Any help or pointers?

    A FW update was recently released to solve the problem with access apps... If you have not received notification on the urge of an available update, you should be able to go to your desire screen and select settings (wrench) > Web > Product Updates > check product updates get the latest FW installed on your printer.

    Regarding the other question - routers are not intended to be turned on/turned off constantly, but it must always connect to your reliable modem after reboot.  Complete the FW update and see if the problem persists.  Also, can you share why you turn off the router on a regular basis - there is really no need to do so.

  • I used the trial before run, but I bought all the apps for 20.00 a month now. When I download it to my computer, it keeps telling me that my trial has expired. I uninstalled the program and reinstalled but it always says "expir├⌐ trial" any id

    I used the trial before run, but I bought all the apps for 20.00 a month now. When I download it to my computer, it keeps telling me that my trial has expired. I uninstalled the program and reinstalled but it always says "expiré trial" any ideas on what I can do? I paid already

    Log, activation, or connection errors. CS5.5 and later versions

    Mylenium

  • We use the CPHA should run us Planning Manager?

    Hello Experts,

    We use the CPHA should run us Planning Manager? Don't do for the MRP?
    Should we even bother to put the MRP: consume MPS, MRP: consume MDS, profiles etc.?
    Thanks in advance.

    Greg

    You must run the Planning Manager. In addition to this consumption of MPS, etc., it does a lot of other functions such as the treatment of completions of job WIP etc.
    It must run somewhere between once every 30 seconds to 1 minute.

    Hope that answers your question,
    Sandeep Gandhi

  • 100% Windows 8 using the drive and Windows Update problem

    I'm going to completely horrible with windows 8.  I use the computer for two reasons

    1.) to run a machine virtual linux which performs calculations for my work

    (2.) to run a very small application that connects to another computer and updates a display based on what is sent to it.  This application also shuts down the computer when the network computer told him to.

    The computer is not connected to the internet, so I chose not to do the windows updates (in Control Panel, never check, do not update, etc...), now that I have a set of drivers that work well.  Took me to update to the latest version of windows 8 (not 8.1), so that the service representative would talk to me, and the problem is more serious.

    I also disabled windows update service.

    Also, after startup, svchost.exe takes 100% of the use of the disc for anywhere from 1 minute to 3 hours.  It is usually about 5 minutes, but takes more time after an update.  I reinstalled windows many times, and the problem persists.  When no other applications running, 10 minutes after the start, opening of windows Explorer takes about a minute.  This computer has a disk decently fast (I tried to replace), a processor quad core and 16 GB of RAM.  When running normally, it is extremely fast.

    My problem is that when I'm at work, a team of 20 or so programmers and engineers may have to wait up to 3 hours for the use of the disc down before you start to work because Windows 8 is unable to work properly.  How can I get rid of this?

    I am considering really just to start the linux and rewrite of the application image bit will run in windows, but I don't want the headache of Active Directory on linux.

    http://social.technet.Microsoft.com/search/en-us?query=Windows%208%20%26%20linux%20virtual%20machine&AC=5

    Try this link for windows 8 & virtual machine. Also, if it's a pc intel based,.

    go to intel.com/support/software/drivers,locate the update utility intel that

    will scan the pc for auto drivers/software.

    Even with the new CD of the OS, you must always configure the hardware on the pc for

    the operating system, most of the cds do not understand that. No windows OS takes also, that

    long to make it ready for the tasks, no more than 10 minutes without

    Progress, stop the execution of its tasks, its in an "open loop"...

  • Computer will not use the drive when you restart.

    I have a Pavilion dv 9000 and had problems more and more lately (win explorer fails, application launcher fail, blue screens, crashes etc.).

    I decided to use the recovery disk that was created at first boot. According to all the manuals that I found (on - and offline), it is just to put the recovery disk in the DVD-ROM and restart.

    The problem is that nothing happens. The computer does not use the disk when it reboots.

    Anyone experienced the same problem with the recovery disk?

    I'm not having any other problems with the ROM, works perfektly once Windows is running.

    Thank you

    You may need to change the BIOS to do first the CD drive in the boot sequence to boot from the CD.  To do this, hold the screen that tells you the key F to push to enter the menu start or start of installation.  Push it quickly. Make the changes, save your work and exit.  Put the CD in the drive and reboot.  When you are prompted, press any key to boot from the CD.

    I hope this helps.

    Good luck!

    Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • Satellite L50-A-103: cannot use the Nvidia GPU as default after Win 8.1 upgrade

    My Toshiba L50-A-103 has two graphics cards, an Intel(r) HD Graphics 4000 and Nvidia GeForce GT M 740.

    In my workplace, I use an external SyncMaster 2032BW monitor with a resolution of 1680 x 1080.
    I've upgraded to 8.1 Windows and I can't use the card nvidia as a default value.

    Now detects only Intel processors with up to 1366 x 768.
    Is there a solution to this problem?

    Hello

    Update you all Win 8.1 drivers and utilities that have been released for this model on the page of the Toshiba UE driver?

    After the update of the system Win 8.1 you must update the drivers in the correct order.
    The installation instruction is also available on the Toshiba driver page!

  • DVD RW drive has an error code of registry 19. I can't use the drive and it is not visible as a drive.

    My lite - on dvdrw lh-20a1l ata device does not work.  Device Manager appears with the following text:

    Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

    Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available.

    I tried looking for solutions, uninstall driver and reboot, reinstall the software provided with the machine, running regecure software to clean the registry and nothing has solved the problem so far - you have ideas?

    19 code means there is a driver conflict such as two devices attempt to use the same
    resources.

    Step 1: Please do all the same underneath if you did some before as is often total
    a process that solves the problem.

    Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
    Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
    RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
    below.

    Then, work your way through these - don't forget the drive might be bad, could be a coward
    cable or slight corrosion on the contacts (usually for a laptop) and other issues.

    Your CD or DVD drive is missing or is not recognized by Windows or other programs
    http://support.microsoft.com/kb/314060 - a Mr Fixit

    The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
    for Windows Vista
    http://support.Microsoft.com/kb/929461

    When you insert a CD or a DVD, Windows Vista may not recognize the disc
    http://support.Microsoft.com/kb/939052

    Your CD or DVD drive cannot read or write media - A Mr Fixit
    http://support.Microsoft.com/GP/cd_dvd_drive_problems

    CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
    Vista installation after booting from the DVD (AHCI)
    http://support.Microsoft.com/kb/952951
    Drive CD - R or CD - RW Drive is not recognized as a recordable device
    http://support.Microsoft.com/kb/316529/

    Hardware devices not detected or not working - A Mr Fixit
    http://support.Microsoft.com/GP/hardware_device_problems

    Another possibility is that the cables are loose. Remove ALL power, then check the cables
    both ends. Remove and replace, do not just tight. For laptops, you can often clean the
    power and data of the contacts with a pencil eraser.

    Some DVD players do not use the Windows default drivers so check with the system manufacturer
    and the manufacturer of the device to see if there is a firmware or drivers for your drive if necessary.

    ===============================

    Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD &)
    Burn DVDs and CDs and read DVDs). So it is not unusual for 1 or 2 operational parts while
    others do it properly.

    Did you follow the Troubleshooting Guide for the reader who still does not work? There are
    the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

    Check with your Maker system and a device for the two possible firmware updates and
    the correct registry entries for your car.

    Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
    as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
    the parameters.

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

    -----------------------------------------------------------------------

    You can probably find more info here and maybe even the exact registry for your CD/DVD settings
    drive from someone with the same model.

    Forums - a lot of expert real help
    http://Club.myce.com/

    CD/DVD units
    http://www.myce.com/storage/

    I hope this helps.

    Rob - bicycle - Mark Twain said it is good.

  • How can I extract and use the driver "exe" to communicate and to load an Excel "cvs" in my Amateur Radio transceiver?

    I use a Mac Mini OS 10.11.3 (El Capitan) processor 2.5 GHz intel Core i5.  With 16 GB of ram at 1600 MHz kDDR3.  I down loaded the program I need and you used my (Mac) excellent program to load the cvs program sheet.  However, the driver is contained in a 'exe' format and I can't or can extract my Mac to use this program.  This driver is required to enable communication between my Mac and radio transceiver.   The only option I see is to acquire a computer laptop windows to allow the use of this application unless there is a program bootable can I mix on an external hard drive and then use Bootcamp?  Help please.

    Try using CrossOver Mac, or install Windows in Boot Camp or an emulator such as VirtualBox or Parallels Desktop.

    (139948)

  • Can I use the drive HARD internal extra for my Satellite A200-1 to 9?

    Hello, new to these forums,

    I recently bought the A200-1 to 9, and I'm very happy with it. I was interested by the addition of an extra internal HDD to the exisitng 120 GB one. I obviously did not have enough research I bought a Toshiba MK2035GSS: 2.5 "HARD 200 GB drive thinking it would be slot directly into the spare slot and it doesn't.

    So, really, I'm looking for some advice if I can add an extra internal hard drive and if so what model and how. After taking the back cover it looks like the aura of the place for another drive, even though I'm not sure if correct connections are there, or maybe if the space is used for something else.

    Any help much appreciated.

    Thank you
    Martin

    Hello Martin

    As far as I know that some A200 models come with hard drives 2. because of this Toshiba laptop brand standard chassis. All A200 models use this standard chassis. Your A200 comes with a single drive HARD and because of this place for the second disc is empty. This does not mean that you can use the second HARD drive.

    I have the same laptop as you and in my case there is no any prepared for second HARD drive HARD drive connector.

  • Why using the driver NOR-DAQmx ANSI C functions in a thread causes a deadlock?

    Firstly, apologies if this is bad advice, but it seemed the closest fit.

    I use MSVC 2008 Express with the library in ANSI C NI DAQmx for some analog output with a box USB-6009. I create a thread to handle the signal generation is based on fixed time. My main thread running the user interface. I found that I get intermittent blockages in release, so that libraries mode NOR are responsible (in the second thread) and I use MSVCRT features (on the main thread). My test code is attached as "deadlock2.cpp".

    I used WinDbg to try to find the cause of the deadlock. Traces of the battery of my two sons are attached as t1_stack.txt and t2_stack.txt.

    It seems that the MSVCRT localtime() function uses a lock when it is called for the first time and then went to lock the Windows DLL loader lock. At the same time libraries NOR (or less libraries mxs) are responsible for locking the charger DLL is being held. The mxsutils library uses getcwd() which seems to try to block something the MSVCRT and therefore my two sons are now deadlocked.

    I can probably work around this by calling the localtime() and the NOR-DAQmx functions before I spawn my second thread so that the DLLs are already loaded in the process. However, I have no guarantee of this to continue working if something changes in the future, and if there are any locks going on finally having the DllMain() calls for a thread hanging may still cause a deadlock. If my results are correct, is it likely that NEITHER would fix the dll for not trying to make something complex in their DllMain()?

    According to NI Measurement and Automation Explorer, I'm under DAQmx libraries v9.3.5f2. I download the latest version now to try, but it will take time.

    Hi dmcminn,

    Thank you for the comprehensive and detailed bug report. I was able to reproduce the problem with NOR-DAQmx 9.6 using the code you posted. I reported it to the R & D team suitable as CAR #366538.

    I agree with your analysis of the problem. Getcwd() so the first call to __tzset() acquired _ENV_LOCK, which Microsoft has documented as the "lock for environment variables. __tzset() also called GetTimeZoneInformation(), which can load additional libraries, that you have demonstrated.

    Here are a couple more possible solutions, but they are not great:

    • Link to the static version of the CRT (/ MT instead of /MD). This would bind a separate copy of the lock of the CRT table in your program, and DAQmx would continue to use the lock to MSVCR90.dll table. They use more of the same _ENV_LOCK.
    • Build using a different version of Microsoft Visual C++ (for example 2005 or 2010). MSVCR80.dll MSVCR90.dll and MSVCR100.dll own separate copies of the lock of the CRT table.

    Whatever it is, it does not eliminate the fact that mxsutils called the CRT while now the loader lock, and this function CRT acquires another lock.

    Furthermore, the forum Multifunction DAQ is a better place to ask questions DAQmx.

    Brad

Maybe you are looking for