varactor diode

I have a problem to put a different voltage to my SPICE2G6 model and get different ability of a varactor diode what should I do?

Please find attached the SPICE model, I need analysis with AWR.

You can try to import spice model, but I recommend place you a model LIDS in a pattern and double click to edit the settings, and then click on "post secondary" to list all the parameters.   Find 10 settings or if in your spice netlist and enter these values.   I think this is going to be the most straightforward approach because it is has only a few parameters to be defined.

Tags: NI Products

Similar Questions

  • MacBook pro 2015 Diode, heating problems

    Hello

    I just bought a MacBook pro 2015, one with 2.8 GHZ, 16 GB RAM and ITB Flash. [old just four days]

    The question being, the first day of the machine as well as the charger were burning Red hot when I loaded for the first time, in subsequent attempts, heating got sorted out by itself.

    Nevertheless, I had installed the temperature gauge in the machine, I look one only a few videos YouTube youtube and navigation.

    Once in every two hours a message like

    The led O GPU temperature is 106 degrees, closing applications.

    Once I click on the tool, the temperature is now reset to 30 ° C. It seems that the temperature of the Diode is to reach 106 degrees, some app is closed (no one knows the tabs I have open in Safari are works well) and then it resets.

    Is it really a problem with the thermal conductive paste or a faulty diode.

    I go to the Apple store this Saturday? Can I return the laptop and request a new or a full refund.

    Can someone please advice?

    If you bought Apple with the last 14 days, you can return it for a full refund.

    http://store.Apple.com/us/help/returns_refund
    Then you can buy a new one.

    What about Apple and they can exchange it without having to go the way of reimbursement.

  • Tecra M11-h-13 Diode GPU overheating

    This probably have no effect as each time that I called Toshiba tech support.
    But I'll try anyway.
    I bought a Toshiba M11-h-13 August since so I need him sent for warranty twice, the first time it was the same problem that has been described in the topic:
    Toshiba Tecra M11 - random crashes with Windows 7
    The motherboard has been replaced.
    A week later, the second problem started. I started to hear the fan sniping faster, but air, it wasn't hot. I run Toshiba health monitor and saw that the internal system temperature and fan speed is always higher than 80%, then I installed Everest which shows me the temperatures of some components, one of them it is strangely warm, Diode GPU, without any program that runs the temperature is above 80 ° c/90 ° c, and the processor and HD was 50 ° c and 35 ° c (approximately).

    After that, I left my pc in security again, and once more, the motherboard has been replaced.

    Again, more or less a week later, the same old problem appeared again, in support of Toshiba, they gave no attention to my problem, they only told to leave my tecra still in warranty, but this time, I can´t be without him, I'm in College, I have a good number of works to show in classes and at home , the examinations to study and I have not the time to leave as security again with the same problem.

    I bought a Tecra because he assumes a laptop no problem, but I was wrong.

    I beg you (Toshiba), to give me a solution to my problem, I think it is unacceptable.

    When I work, sometimes with programs that was not supposed to use image as matlab when it's calculus, the GPU diode reaches 125 ° c more then, and when I'm in class and I need to have a job to give my teacher on the end off the class I stop can´t or my notes will be '0' in which works.

    The rest of the temperatures remain much below that level, as the processor at 75 ° c and HD 30 ºC.

    I don't know just what to do more, I have restart my laptop, it is updated bios.

    Solution please...

    Best regards
    Jaime Araújo

    A few questions:

    (1) are the vents breathe easily? The system may overheat if the vents are blocked.

    (2) have you tried to remove any dust or dirt build up? Try spraying Compressed Air from the vent.

    (3) are to you using the display standard driver from Toshiba Web site? Install the other drivers can cause this kind of problem.

  • MBPro Mid 2015 GPU diode 0 high temperature

    I recently got a new MBPro 15 "mid-2015 (16 GB of Ram with Iris Pro).

    I use temperature indicator 4.1 and get sometimes a message saying WHAT GPU Diode 0 received at 98 ° C for a short time. Is this normal?

    This request is quite old. It has not been updated in over 2 years. It is quite possible that it is not properly read information of your new Macbook Pro.

    I use iStat menus (https://bjango.com/) and I don't see any sensor labeled "GPU Diode 0".

  • Where can I find a model of Diode of Josephson?

    I need for my work of design of this model, but I can't find it in the element tree.

    Characteristics of APL license will be activation allows you to see and use all APLAC RF, which was shown in the picture of the tree elements in the previous post.  Of Josephson Diode model is available without any necessary licenses APL function, but must always be simulated with APLAC Simulator.  Of Josephson Diode model can still be found by browsing the tree > APLAC > Passive > JJ_AP or can be found using the circuit element dialog box Add (CTRL + L) and looking for the description "Josephson.  If you do not have libraries of APLAC RF element in your game then your tree might look more features as follows:

  • Read a resistance of the diode by vs NI USB multimeter

    Hello

    I read a resistance of the diode at some entrances to supply voltage

    and I found that

    to 0.2 V

    the value of resistance by NI USB-6212: 200 ohms

    the value of resistance of meter: 2 kohm

    0.5 v

    the value of resistance by NI USB-6212: 500 ohm

    the value of resistance of the multimeter: 5 kohm.

    Could you please let me know why the values are different by 10 times?

    Thank you.

    No - we can't measure the resistance in this way.

    To measure resistance, you normally spend a current known and then measure the voltage. A DMM will be repeated by generating a little known current and measuring the internal tension. If you provide an external voltage thus, DMM internal resistance measurement will not work.

    For the LabVIEW - The USB-6212 can measure the tension. If you want to measure resistance, while the unit is plugged, you need to know/measure current (for example through a shunt resistance) and the tension and then do R = V / I for the resistance. I don't know what the argument of type 6212 if you try to perform a measure of 'resistance', as it is not a source of internal current.

    Oh, I thought that this all seemed familiar - here's a similar thread: https://forums.ni.com/t5/LabVIEW/daqmx-resistance-measurement-6251/td-p/3267084

  • Nonlinear worthy of the equations of the diode

    Hello

    I want to make an adjustment not length of the features of diodes.

    The function that I need to set up is could be written as Y = f (X, Y).

    This means that the data is both the goal of adjustment and a part of the equation.

    Is this possible with the vi made nonlinear of levenberg-Marquardt?

    Best regards

    Baptist

    OK, I understand.

    I ' l try tomorrow morning.

    Best regards

    Baptist

  • Multisim has a zener diode two-way which act as limiter circuit?

    Hi all. I want to simulate a curcuit that she can act like a limiter circuit.

    But I can't get the good two-way zener diode. the two-way zener diode in the next sch does not work!

    the output wave is the same as the wave of entry. the amplitude of the output wave is not limited.

    Ok. I know. Use two diode zener serial!

  • cFP-DO-401 fuses and flyback diodes

    I use a cFP-DO-401 to command 24V solenoid.

    On
    page 4 of the Handbook of PSC-DO-401, it says to merge output with 1. 5A
    fuses fast action, that makes sense. But rather than put one online
    fuse on each of the 16 threads, anyone know of a fuse block or
    module which must be connected between the cFP-CB-1 module and the CFP
    bottom of basket?

    In addition, on page 8 of the manual, it shows that
    The cFP-DO-401 has inside flyback diodes, but then he says OR recommends
    using those outside. Why external are needed if the cFP-DO-401
    already has them?

    Mosey,

    Here is the link to that which is available from Digi-Key.  http://search.digikey.com/scripts/DkSearch/dksus.dll?detail&name=277-1569-ND Allen Bradley also makes a line of similar pieces.

  • failure analysis of diode

    I tried to design a problem for the analysis of the student - and tried two diodes in parallel - but with resistance

    above and below of one of the diodes (diode therefore is not potential ground on each side).

    Multisim failed to produce a DC solution.

    LTSpice worked well.

    Then... How Multisim to produce good results?

    Oh my! I don't see that.

    I know what your problem is. The two sons that you named N3 and N4 to LTSpice are all two appointed 2 in Multisim. These two wires will be behave as if they are connected. We call this a virtual connection. To see the name of the net, double click on the wire. I also recommend that you put on the visibility of all the names of net for debugging:

    1. Click Options > properties sheet
    2. In the Circuit tab, click Show all in the net option box

    You're not the first person to be victims of this behavior is not so obvious. We addressed this issue in our last version, Multisim 11. Virtually connected nets are explicitly designed with connectors now and it's much more difficult to police this kind of problem.

    In the meantime, if you don't want to upgrade to Multisim 11, it is worth your while to upgrade your Multisim at 10.1.0.1. There was a bug in 10.1, which fixed us for 10.1.0.1 which could cause this strange behavior. The 10.1.0.1 update is available free of charge via OR Update Service.

    Hope that helps.

  • Why is there not coherent diode to 0,7 v voltage drop?

    Evaluation version of Multisim11 students. In a domain controller series simple circuit with a resistance of 10 ohms and (3) in4148 diodes before biased, voltmeters through each equal tension to the diode with each diode, but when the dc supply voltage increases, the voltage at the terminals of each diode increases. A technician quiz (and the theory of diode) indicates that the tension will change not through the diodes and should stay at 0.7 to 1 diode, 1.4V 2, 2.1V through all three together, even while the supply voltage is increased, but why not Multisim reflects the basic diode theory? I use the default settings for counters and components. This was also a problem for reverse and measured from current levels of polarization tests. I'm almost never able to get the same results, as provided for in the school laboratories.

    10vdc, I get 1.593V each diode

    Get 3.777V each diode to 30vdc

    What's the dealio?

    I can I answered my own question by experimenting with the circuit. The value of 10 ohms resistance is not high enough to avoid overloading the diodes. A value more realistic of 1Kohm and tensions of 5-10 v using 3 diodes BAS16 show diode drop of tensions in the range of .691mV to .750mV. 30V even still shows a drop of .836mV diode.

    So what kind of diodes would work correctly in this circuit with a resistance of 10 ohms in series and a range of 10 - 30V dc voltage? The quiz of technician stated that this circuit has a resistance of 10 ohms. Maybe it was a typo?

  • VI LabView for HP 4145: measurement of diode IV

    Hi all:

    I'm new to the forum and also new to LabView. I searched the forum question I'll post and want to let people know in advance that I found no relevant response / concrete.

    I want to use LabView 2015 to read data from an old HP 4145 B semiconductor parameter Analyzer connected to a probe station. I also have a GPIB interface OR to make the connection bewtween LabView and the HP 4145 B.

    I would like to know if there are any VI available for the 2 terminals (in this case on the wafer diodes) so that I can order directly facilities of LabView and be able to read the measured data directly from the HP4145 through LabView? The data I want to represent are curved IV.

    Best regards and thanks in advance for your support,

    George.


  • DIODE IV CHARATERISTICS

    Hello

    I'm currently stuck upward while applying the characteristics of the diode using LabVIEW. I tried a great ways to get the curve of diode, but my efforts are in vain. I'm sincerely looking for using you guys here. I have attached two .vi
    The linear diode with curve.vi is one in which I realized a linear increase in speed with a small increase in tension.
    The second ideal.vi of diode is on in which used realization and achievement of State after the ideal conditions.

    The readings are carried out using my first year in review.

    I am very new to the software and would appreciate any help. I have Labview v8.5 n v10.

    Thank you

    The inner loop stops at 0.7 only if get you lucky.  Add indicators related to the constant of 0.7 and the v (t) inside the loop line.  Set the display format on the two inidcators to 18 significant digits and uncheck Hide zeros to the right. Turn on execution highlighting to slow things down. Configure Vmin reset and dV to 0.05 and watch it. See the image below.

    Look at this example for a simpler approach (and one that uses a more realistic model of the diode).  I put comments on the block diagram to explain the differences in your VI.

    Lynn

  • Diode recovery step in Multisim

    Hello!

    I analyze and compare a few diodes recovery step in Multisim, but there is a problem, I can't find one of the step recovery diodes in Multisim... what should I do? Y at - there a Posibility to create a DTH in Multisim?
    For example, I have to analyze some on these diodes: http://www.aeroflex.com/ams/Metelics/pdfiles/mmd_sp.pdf

    Please help, this is my first time using Multisim.

    Thank you!

    Hello

    You can create your own templates using the component wizard. Once you get to the section to enter a SPICE model, you can find model SPICE of a specific online diode if it is available from the manufacturer, or create your own by using the designer. Selected in the diode, you can have a lot of advanced options such as the typical reverse recovery time, maximum current of DC source, transmit the current and voltage, etc. If you know the specifics of your DTH, then you should be able to model using the tool.

    Hang on, I just saw you linked to aeroflex SPICE models. Take a look at this tutorial to create your own component using their SPICE model.

    http://www.NI.com/white-paper/3173/en

    Kind regards

  • transistor for my diode-transistor vi equation

    This is a diode and transistor vi. You can change transistor/diode under the graph. in the block diagram of the diode you will see that it uses an equation for the current. I put an equation and create the schema for the transistor also so I can see the curve in the front panel, but I can't seem to find what equation I put! does anyone know what equation works?

    The same question, asked differently.

Maybe you are looking for

  • can firefox play a mp4 file?

    I have a html 5 lines of code on my server uses the tag video. the movie I mention, in the code, is a xxxxxx.mp4 fileI can play this mp4, online or offline, in IE, Safari, Chrome and Opera, but NOT in firefox (I have v12). It gives err: "no video wit

  • private browser option is missing

    I added an application (I forgot the name of it) that would end "private browsing" because I wasn't sure how do. Now the option in the tools pulldown disappeared... I'm stuck in private mode and can not find a way to remedy. I tried to add another ap

  • When I click the icon of ff, it does nothing... does not start

    Firefox will not work when I click on the icon. I tried to reinstall and did not work. There is no error message.

  • Update BIOS issue and on Satellite A200-1z3 FN key

    Dear all, Satellite A200-1z3 I have the same problem as many of you already described here. After downgrading from Win XP, I discovered this part of the features enabled by the FN key don't work, for example FN + F2 FN + F6, FN + F7, FN + F8, FN + F9

  • Primary control loop and loop DIO

    Hello I use an X-series with Veristand 2011 card. I need to acquire some AI and DI whole. It seems that the AI will be supported by the main loop, which is very good for our goal for now. But what of the DI. Looks like the DIO loop works like a rate