VCS licenses on BE6000

Similar Questions

• Weird VCS licenses use

  Hi all

  I have a problem with strange license on a virtual VCS installed on a BE6K:

  I have an endpoint registered in H323 and SIP on the VCS (7.2.1) and a Cisco Jabber for windows saved to a CUCM (9.1). CUCM and VCS are connected by a section of the SIP.

  Here's my question:

  I can make a connection with appeal from the endpoint to jabber: it uses 1 non-traversal call.

  When I make a call to jabber, endpoint, VCS reject the appeal because max traversal appeal is outdated! When I check the dashboard overview, I see that this call is using 9 golf courses appeal!

  Anyone of you has an idea about this?

  Thank you

  Best regards

  Bruno

  the cause of loop usually (but not the only one) is a bad searchrule branching calls through several areas. If you enable your debug mode on VCS and newspapers through the logs that you would see how many areas were considered a potential candiate for the destination of the call and a branched call was created.

• License VCS\VCSE of virtual machine hardware migration.

  Hi all

  I want to migrate my hardware to virtual VCS\VCSE.

  Both servers are covered by the active maintenance contract.

  How licenses work in this case? What is the procedure of transfer?

  Any cost?

  Thank you.

  Hello

  About Cisco VCS, you want to migrate virtual machine hardware, you will need to purchase a new license to make the transfer. These are the partnumbers you need:

  R-VMVCS-C-M-K9

  HW migration to E - Delivery Virtual VCS only controls

  R-VMVCS-E-M-K9

  HW migration to E - Delivery Virtual VCS Highway only

  Please contact your Cisco representative for more information.

  After purchasing the license, the license of the VM device rehost will be made by a specific Cisco team, not the team of global license, it is a process different rehost. You will need to send your request to [email protected] / * /, this team will provide instructions to rehost your VCS license correctly.

  I hope this helps.

  Concerning

  Paulo Souza

  Please note the answers and mark it as "answered" as appropriate.

• VCS Express with CUCM 10

  Hello

  There is a lot of confusion on Express C/E & VCS C/E, if anyone can confirm my following queries:

  With VCS VCS & Express control every endpoint to register with VCS control (no participation required CUCM or VCS control can't integrate with CUCM)?

  With Highway Core & edge that every endpoint is record in CUCM & CUCM will record Expressway Core?

  For calls B2B & movi Jabber, that we must have Expressway Center/periphery, VCS control/Express IS NOT support jabber movi & called B2B?

  Software Express C/E & VCS C/E are the same, but the licenses are different?

  Our clients have obtained

  1 x control VCS licensed

  1 x Express VCS under license

  1 x ISDN gateway,

  1 x TP driver

  1 x TP management suit.

  Kind regards

  Francisco

  With VCS VCS & Express control every endpoint to register with VCS control (no participation required CUCM or VCS control can't integrate with CUCM)?

  Yes, no CUCM is required, endpoints can also enroll in the VCS-E or it could register SIP to VCS - C proxy endpoints. A parallel installation of VCS CUCM with a trunk should also work with todays versions.

  The VCS will be only support standards basis of endpoints SIP and H323, its main purpose

  a for video settings. You won't be able to use it to register, provision or use of Cisco IP phones with it.

  With Highway Core & edge that every endpoint is record in CUCM & CUCM will record Expressway Core?

  See the C & E highway as a single unit to the external communication. The registrations are transferred by proxy

  CUCM outside.

  But that also means, you can't register 3 party at the highway and even end points

  Cisco endpoints must support the installation of the fast track C & E.

  The highway also runs things like XMPP for Jabber.

  For calls B2B & movi Jabber, that we must have Expressway Center/periphery, VCS control/Express IS NOT support jabber movi & called B2B?

  The C & E Highway can also manipulate calls business2business or another sip trunks / h323, but this infrastructure requires the media license.

  B2B calls also works very well with the installation of VCS.

  If you are talking about how to provide Jabber accounts and video Jabber:

  There are video Jabber (which is implemented by TMS and VCS) and Jabber (i.e. led CUCM) there.

  If you are talking about outside calls that he can just be regarded as regular b2b external calls.

  then they be it work with VCS or motorways on the site of the end.

  Software Express C/E & VCS C/E are the same, but the licenses are different?

  It is correct. Licensing Expressway is more attractive for users CUCM, but you already have

  have SPRDD in place that should work in all cases well.

  With CUCM, you get licenses Expressway in any case. So according to the type of use, you.

  B2B, internal calls... you can add a configuration of fast track to Jabber and the stuff of office home and

  use the VCs to B2B and part 3 records.

• Vcs Tandberg and Cisco VCS control

  Hello

  I have a client with an old would invest video and new servers.

  Old video servers

  Control system Tandberg video Communication Server - part number = 117500

  Application of Tandberg video Communication Server Expressway - part number = 1163402

  New video servers:

  VCS License Control - Part Number - R-VMVCS-CTRL-K9

  VCS Expressway License - Part Number - R-VMVCS-EXPWY-K9

  According to Cisco x8.2 Clustering:

  -Each peer runs on a hardware platform with equivalent functionality; for example, you cannot cluster one
  peer running on one core 2 average VM with peers running on base 8 large virtual machines

  Means that the physical old VCS cannot be grouped with new virtual VCS.

  Thank you.

  Hi zizou.

  You can include a device VCS with a VCS VM as long as their matches of software and their hardware platforms have equivalent capabilities.

  Device VCS clustered with VCS VM running on core 2 MediumVM = YES

  VCS machine clustered with VCS VM running on 8 cores LargeVM = No.

  "you can even cluster that are running on the standard devices with peers running on core 2 Medium VMs, but you can not group a peer running on a standard unit with peers running on base 8 large virtual machines.

  (p.4)

  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/infrastructure/VCs/config_guide/x8-7/Cisco-VCs-cluster-creation-and-maintenance-deployment-guide-x8-7.PDF

• cluster with telepresence Server 8710

  Hello

  Currently, I want to deploy the client conference and here is the list that I bought for my client:

  -telepresence Server 8710 with 24 licenses x 2

  -MSE 8000

  -License CUCM

  -VCS license

  My questions are:

  1. from the Cisco documentation, I know that 2 of my server of telepresence could be clustered. 1 my server Teleprsence will be the master blade and the other will be the blade of the slave. By doing this, my server of telepresence is already grouped?

  2. I don't have a driver's license, but I know that this driver could manage 1 telepresence Server wethere that she is not allowed. I tried to manage my my server in cluster of telepresence, but he said that driver had 2 telepresence managed server. I thought that my number of clustered server of telepresence in 1 for conductor. Can someone explain this?

  3. what happened to the deployment guide if I want to use all my 24 licenses? From my understanding, 1 Telepresence Server Blade can only manage 12 licensing screen and cascade could not been since I couldn't do it as remotely managed. Help, please.

  Thank you.

  Telepresence Server MSE 8710 installing blades are autonomous, it is not until you configure using the blade of supervisor MSE 8050 they will become a cluster.  See clustering on pg 90 of the Supervisor MSE 8050 Help Guide.  I don't know how a cluster server Telepresence would manage a conference which exceeded a unique ability of blades that was within the cluster, but according to the help guide of supervisor, it is said that the master blade could allocate licenses video port to the participants in the Conference that could be a big conference or several small conferences.  I would say, just create a conference and start adding in the participants and see what happens.

  Looking at the conductor data sheet it is said that the Essentials (or the free version) can support '1' (independent), since a cluster behaves as a single server, but in reality it is more than 1 server it probably not supported.  The conductor Admin Guide on pg 17, it is confirmed that the free version of conductor does not support cluster conference bridges.  It seems that if you want to use with driver cluster conference bridges, you must at least move to select conductor (middle version), because the free version does not support.

  If you use driver for some reason, you should be able to configure the 8710 blades runs remotely managed mode, I have several configured this way, but they are all autonomous blades, none is in a cluster.  Help server TelePresence MSE 8710 Mode guide managed remotely on the basis

  Is there a particular reason that you must use a driver, why not use the blades of telepresence Server 8710 MSE mode managed locally in a cluster?  Help server TelePresence MSE 8710 Mode guide managed locally based

• Cisco Telepresence Server/Cisco Telepresence driver/Cisco VCS - C / Cisco TMS license

  A big problem with the fact that I'm stuck is licensing. Really, I have tried many things to find the solution for it, but could not.

  I have actually made all of these servers (mentioned in the title) in my lab in preparation for the CCNP Collaboration certification at home.

  I am not able to complete some laboratories due to license issue (I guess). Y at - it an option to get the demo license for all these servers?

  I would be really greatfull if someone can suggest me the solution and/or the licenses required to complete all the stuff for my CCNP Collab tag.

  Best regards

  Dipak Singh

  TMS and VCS - C when installed without licenses, are automatically set mode of demonstration/test with some availability of license to test with. If needing a VCS-E, you will need to do to your account manager and they should be able to get you the time limited licenses good because I think that 90 days.

  Conductor Essentials is free, which means that you can install and get full functionality without the need of all licenses, but you are limited to 1 conference bridge and no grouping is allowed.

  TelePresence Server require licenses to function, once again, reaching out to your account manager for this.

  At the end of the day, you should reach to your account manager for all of this, as they should be able to help get timed license if you need.

• Telepresence - who ensure license on telepresence in VCS

  Hi guys,.

  I need to check the license of telepresence equipment reference in VCS, but I Don t have any experience on the VCS. That I can check this license on VCS. I know that models telepresence recording in CUCM and anothers in VCS.

  Thank you

  Wilson

  When you connect in the VCS, you can check the status on the landing page to see the use of the license. To see more specifically what licenses are installed, click the Maintenance > Options keys.

• License of VCS & MSDS

  Hello world

  I need to clarify some doubts with permission of TMS and VCS:

  Our customers need to add endpoints SX20, the customer already has a deployment of TP with TMS, VCS Expressway & control, MSE8510.

  I have two options:

  1 - save the SX20 endpoints in CUCM and use of TMS for planning.

  -The permit required for CUCM 9.x: R-UCL-UCM-LIC-K9 (LIC-TP-9 X-ROOM)
  -The permit required for TMS 14.3.1: L-TMS-SW-PAK (LIC-TMS-100)

  2 - save the SX20 endpoints in VCS and use of TMS for planning.

  -The permit required for TMS 14.3.1: L-TMS-SW-PAK (LIC-TMS-100)
  -The permit required for VCS X.7.2.2: L-VCS-PAK (LIC-VCS-100), I'm not sure if I need this license for firewall VCS non-traversal?. If each SX20 is registred in VCS is not necessary this kind of license, right? Will be requerided if I need SIP-H323 o IPv4-IPv6?

  Could you please confirm if I'm wrong? Y at - it another option? Do I need other permits?

  Any other comments are welcome.

  Thank you

  Pablo

  Hi Pablo.

  If you add just additional end points, the easiest way would be to add to the existing deployment (option 2 above) rather than adding additional complexity with CUCM (option 1).

  According to the license on the current deployment, you may or may not need to purchase additional licenses.

  (1) to check their existing TMS to see if there are licenses available system (this is shown on the display main portal when you open a session (near bottom of box to the left).  If you need more, you can buy them - you don't mention how you add - but you can buy them in smaller than 100 packages if you need (IE a L-TMS-25 is 25 licenses of system).

  (2) check the VCS control the number of licenses currently installed (they are once again, on the first screen get you when you open a session).  Check the license limit and of leading figures - that should give you an indication as to the relevance any more necessary or not (that is to say, if the vertex figure is not closer to the limit, you will not need to buy more).  Again, you can buy them in containers smaller than 100. They allowed to 'simultaneous call', so you generally do not have one for each device.  If all calls are within one organization on the VCS, Non-Traversal licenses, you will need on the control VCs.

  Let us know how you go, or if you have any other questions.

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• VCS - C license server

  Hi all, I have a question about the licenses from the VCS - C Server I bought for the demo. I have reset the factory default server and all licenses have been lost. What should I do now to recover the licenses?

  Serial number of the server is: 52AXXXXX. Software version: X7.1

  Hi, please contact cisco account/sales manager who had provided the VCS - C for the demo server and it will help to share the demo license.

• Can we use licenses of the highway on the highway VCS?

  Dear team,

  We have 10.5 CUCM, control VCS, MCU, ISDN GW TMS Infrastructure deployed in one of our customer place. Now the client asking the Internet settings to be able to join CUCM registered endpoints. But we got the highway licenses and so we installed aboard the VMinstance Highway and installed licenses, now my query is this set works? Otherwise, we can transfer those licenses to expressway VCS?

  Please suggest!

  Hi Eric,.

  In brief - customer is working to achieve both Business - to - Business (B2B). Yes, that can be reached. Note: You will need to have the right set of licenses.

  Note: you mentioned VCS control and the edge of the highway. So, what are the components you have in the network? Control of VCS and VCS Expressway or VCS Expressway-Core and VCS Expressway-edge?

  Kind regards
  Chirag

• Demo of VCS - C VCS-E without license

  Hi all UC TP Experts,

  I just deployed the ovules of VCS 8.1 (s42700x8_1_0.ova) for the C Highway and Expressway-E on the Jabber without VPN demo. She is successful for me to configure the Expressway-C and it is failing for me create the 'traversal server' box on the highway-E, but I can't see the option "route server.

  I have to insert the option key to activate Expressway-E, which will change the role of VCS to the highway E.

  Note that during the first installation of the motorway of the VM, the area of banner on the web interface will display Cisco TelePresence Video Communication Server. After the installation of the option key Expressway series the banner area change to indicate Cisco Expressway-C (or Cisco Expressway-E if the Traversal Server option button has also been installed).

  REF.: http://www.cisco.com/c/dam/en/us/td/docs/voice_ip_comm/expressway/install_guide/Cisco-Expressway-Virtual-Machine-Install-Guide-X8-1.pdf

  I'm little urgency to make up for the demo. I have no idea if not to order the license, then I can activate the function of Expresswa-E?

  Expresway demo keys are available from X8.1.  Take a look at the following thread, last post.

  https://supportforums.Cisco.com/message/3742737

• How to pass the vcs - e License? A server to Server B.

  Hello

  my company has a vcs test server.  and we buy the new server.

  I need to spend vcs again server.   I backup and deploy using the vmware ovf file.

  deploy the success. but new server vcs poster license error.

  How to pass the license of vcs?

  Of his assignment, it is not necessary to use both servers at the same time.

  If I see, if you move the virtual computer between two servers and you used local storage the

  Serial number will change...

  Please remember useful frequency responses and identify useful or correct answers.

• Do we need to purchase the license to upgrade the VCS, VCSe and TMS?

  Hello

  We need to get a new license when upgraded version of VCS, VCSe and TMS?

  Hi Kelvin,

  xxx. OVA files are package files to deploy the VCS on virtualize platforms.

  Release key are required to upgrade the VCS for major updates. for p. ex. upgrade of x 6 x 7 software version worm.

  However for improvements minor as x7.2 to x7.2.2 these are the released hotfix version or bux fixes release and you don't need a license for this upgrade.

  in any case if you your devices are less covered by valid contract you can get the license key anytime just contact cisco license team on "[email protected] / * /" and they should be able to provide the necessary license.

  Rgds

  Alok

• VCS HW license VM migration

  We recently bought 4 x LIC-VVCS-E-M-PAK and 4 x LIC-VVCS-C-M-PAK so that we can migrate all our calls licenses from VCS HW devices to virtual machines, but when I go to buy one of the PAKs I got for the VCS - C, is that display the following information available:

  		LIC-VVCS-C-M-PAK	1
  		LIC-VCSE-100	1
  		LIC-VCS-GW	1

  Shouldn't it allows me to enter the serial number of a device from HW to migrate, then give me licenses relevant call too?  Has anyone else had experience migration licenses HW to VM that might help us with that?

  Hello Nick.

  Please mention the discussion below, you will need to send a certain group with Cisco to process the query to rehost the option unit to the virtual computer buttons.  I am sad to say that it is not no matter how automatic background process that does this when you buy a migration for any product, it is all the manuals and done by the client most of the time.

  vcsvcse-license-migration-material-vm