VCS registration issues.

Similar Questions

• C VCS registration issues

  Hello, I am facing problems of a new endpoint SX20 recorded in the control of the VCS, we received it with version 7.3.0 and each time it was recorded as a H323 device in the control of the VCS, has shown in the point of termination and VCS as good, but the h323 calls cannot be forwarded I checked the record in the VCS control and the RAS RAS Signaling as a 0.0.0.0:1719 location, the first thing that comes to mind was that a firewall can be malforming the package, I checked open ports too just in case about to endpoint and h323/q931 was open, otherwise he could not register at all. The I did a logging extended in the endpoint to capture recording debugged and found that endpoint sent the RAS location, signage with 0.0.0.0, generated from the endpoint itself, my question is, what could be caused by this problem? I upgraded to version 7.3.1 TCS endpoint, but the same thing happens, would it be a hardware problem? Whenever the system retrieves the IP endpoint of the NIC, to send it in the form of signs of RAS/places, there must be something wrong, the process or it receives the ethernet config? I have many other features of h323 of registered endpoints and works very well. Because now I have registered in the system as a SIP device, and works very well, which makes the VCS not interoperability, including the SIP registration confuses me, because it also retrieves the ip configuration and registry endpoint SX20 very well.

  Found the problem - under configuration H323 there is a parameter to the NAT, which had failed on 'On '.

  Set to 'Off' correction of the problem.

  I hope this helps...

• Phone IP Cisco CP - 9971 VCS registration...

  Hi all

  Can someone please confirm is possible to record the Cisco IP Phone CP-9971 on a Cisco VCS control server directly. If possible, I appreciate a guide or a document for this. I have a VCS on X7.0.2 control.

  Please guys suggest something.

  Thank you

  [email protected] / * /.

  Skype ID:-arun.sharma963

  Mob. + 91-8088071229

  Hello.

  You can not.

  Any Cisco phone requires a server TFTP provide the firmware and configuration. A VCS is only for the registration of the device.

  As a result, phones depend on a CUCM as Registrar. It's a plant (CUCM) vs decentralized approach (VCS).

  I had a lot of Cisco phones on my Asterisk server, as SCCP or SIP phones. But you must have good knowledge how to generate XML files that are used as configuration files.

  Concerning

  Danny

• CS3 mic - newbie registration issues

  Hello

  I have a few questions about the record from a microphone I play a timeline with video in it... like if I do a narrative v.o...

  This is the first time I used his Age stuff... and am just setting myself up to start to 'learn' on audio with CS3 re: recording and mixing etc...

  so please excuse the simplicity of these questions... I use onboard sound with just stereo spkrs hung and that is a driver for dell 530 realtec

  ---------

  Audio
  Type Realtec ALC888 (7.1 channel)

  -------------

  My notes... the questions and...

  When mic on before recording... can hear sound in lft spkr not right...

  When the record can be heard in the two spkrs... but with an echo

  reading on the two spkrs... ok no echo... sounds good...

  about a seconde.5 delay before recording begins actually after hitting the "Play"... How can I synchronize that upward on the timeline with video... just move video far 00.00.00 before registration? maybe move corresponding sequence (if it was a narrative vo for example) to a track separate and far 00.00.00 seconds as its has a chance to become active on record, knock out the microphone with a stick when I go to the 'start of the clip' for synchronization and then make my original?

  as you can see I'm making progress for a beginner...

  It sounds like (pun intended) you hear a latency, where the echo. Some microphones and more audio cards have latency issues.

  Is mono or stereo microphone?

  I always turn off any speaker, when recording through mic and use headphones. There may always be a latency, but it should not intervene.

  You y USB mic? Adobe programs often have problems with USB microphones.

  If you get a delay of 0.5 seconds, and it's fairly consistent, then maybe add 0.5 sec. Black Video at the beginning of the video, to give you a "rolling start". Once completed, this, simply remove it properly. As I normally start my 02 seconds of Black video footage, I have some time, to do things at speed, before that I even start recording. I do that s 02 for other reasons too - allowing a DVD player lock on my track DD 5.1 Audio SS, so the first few notes is never truncated. You do not DD 5.1 SS, IIRC, so this isn't a necessary review.

  Good luck

  Hunt

• Registration issue

  Hello everyone.

  I bought the new PC toshiba laptop. I paid for it on June 19, but due to some problems with the first laptop that I got a second on 24 June. Then I tried to save it using the icon on the desktop, but I couldn't. I was informed that the recording time elapsed. What should I do now to register my computer and that the entire warranty?

  Kind regards
  Mast, Poland

  Hello Matt

  I recommend you call the helpline in your country. Explain the situation and they will explain what needs to be done about it.

  Before doing this, you can try to repeat the registration process on http://eu.computers.toshiba-europe.com/innovation/generic/services_warranty_reg_map_eu/

• Satellite L750 - Lag latency of registration issue

  MY PROBLEM.

  I used my desktop pc to record guitar on a pre backing track recorded using programs: fruity-loop, Audacity etc. without problem.

  When I try the same on my laptop the problem of latency L750 does not listen to what I play it IE 0.5 second delay of the note to be played to the sound being heard.

  I adjusted the settings of latency in the programs that I use, but this makes no difference.

  Can anyone come up with a fix for this problem because my new laptop becomes a zone of decanting for dust on my desk. ???

  Hello

  I can recommend you to try tools like LatencyMon and DPC latency checker for information on the driver causing the latency issues.
  Here's a thread on the same topic:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=67087

  I remember that and old TSRI (Intel Rapid Storage Technology Driver) caused this show too.
  This could be resolved by the updated version of the TSRI at least V10.1.0.1008

• OfficeJet Pro 8620: Care Pack registration issue

  I bought a HP Officejet Pro 8620 on 17/12/15 at a local retailer. I bought a 3 years Care Pack 20/12/15 HP online. I received the care package on 26/12/15 and went online to save it. By doing this, I got an error message: "(REG041garantie faible) the present material products can be verified." To complete your registration HP Care Pack, please contact HP and provide proof of purchase of equipment". "" 12/28/15 I faxed (to 541-715-5522) a copy of my Bill, a copy of the label from the printer box and a copy of the completed "HP Care Pack card registration. I expected to be notified by e-mail of the recording, but I got nothing from HP. A phone call from me would not help because they wanted "proof of purchase". Anyone know how can I know what is happening?

  Hey @nhuser1,

  I see you try to find out if the Care Pack for your Officejet 8620 e-all-in-one printer has been saved. For this problem, that you que vous devez need to either call the phone number printed on the card registration of Care Pack or contact HP technical support. You can contact technical support by clicking here and filling out the form below.

  Please let me know if this resolves your problems or if you have any other questions. If not, have a great weekend!

  If this solves your problem, then please help others find this post by clicking on accept as Solution on my post.
  
  If you appreciate my help, so please let others know by clicking on the icon below my post thumbs up.

• Tests EX60 UCM and VCS registration

  Hello

  I did a few test with Cisco EX60 a few days ago a the following infrastructure:

  -UCM 8.6.2

  -Cisco VCS control X7.2.2

  -Cisco EX60 series

  -Csco EX90 series

  -Cisco CPIC

  -Cisco IP Phone

  The goal was to try to save the EX60 in SIP mode with UCM and H.323 mode in VCSC and make some calls with EX60 register in both devices, because I have found no documents where it was stated that only I can save EX60, EX90 in VCS or Complutense University of MADRID, but not in both at the same time.

  I recorded the EX90 in VCS and EX60 in VCS (H.323) and UCM (SIP).

  All calls to H.323 devices EX60 send control VCS and all calls all works fine without any problems. If I try to call EX90 to EX60 in SIP mode, the call will be fails. When the EX90 with EX60 H.323 call is connected, the University Complutense of MADRID and using RTMT I saw that the EX60 was on appeal or in busy state.

  -Audio call of the registered IP phone or CPIC to the AAU to EX60: I saw the call in the call control in the EX60 and RTMT and Complutense University of MADRID, but I did not see the call to the control VCS Cisco. If I try to call to EX90 to EX60 using H.323 right now, I got an EX60 busy tone. Also, if I make an audio call to EX60 for an IP phone I can do another audio EX60 call to an IP phone or an EX90. EX90 try to video negotited but calls finally was audio only.

  -The presence does not work when the EX60 is under appeal with the other end H.323 in the Complutense University of MADRID, too the BLFs do not work and does not appear the call at the Complutense University of MADRID.

  -Si EX60 is videoconferencing with EX90, the EX60 can receive an audio call to UCM get connect and the presence and the BLFs working properly.

  I find no more problems at the moment.

  Kind regards.

  This isn't a Setup program that you want to use, or register them both to the VCSC or

  Let CUCM control your end point, then h323 must be disabled.

• Conference MCU SIP with VCS registration question

  Hi all

  We have a cluster of MSE 8510 MCU (software version 4.5 (1.72), Build 6.19 (1.72)) with 86 active confeneces. All of them are configured in the same way, to use H.323 and SIP registrar calls control.

  The thing is, I can see all conferences recorded under H323 and some of them just registered as SIP on the VCS cluster (X.8.2.2).

  What is the problem? Why can't all register using SIP?

  See you soon,.

  Petar

  Can you check to see how many conferences are recorded using SIP?

  If it's 50, this seems to be the maximum that can be recorded, see enhancement request CSCum48651.

• LR5 registration issues

  I just bought Lightroom 5 after completing the 14 day trial. The trial worked fine, but when I get my purchased serial number and registration information, click on 'Finish' don't close the program. I'm under OS X Mavericks of developer preview, even though, as I said before the trial worked. Someone else has experienced this problem or found a fix?

  I have just contactacted Adobe and they had me go to library > Application Support > Adobe > Lightroom and delete the record from the file in there. I then open Lightroom, and I went straight into the program.

• CS4 registration issue

  I just had installed photoshop CS4 update. Everything went very well, installation and update. Everything seems to work very well.  Screen recording poped up, I completed and click on register. Box poped up, which said it would record the next time I had an internet conection. I have one... She found the updates very well on the line. If I go to help... The registration form is still there and if I click on send the same box comes up... I don't understand. Nobody knows what can be up with this... Peter

  Windows 7 64 bit

  You can register new products in the store / area of my account from the www.adobe.com

  I tried to register my CS4 E several times and he couldn't stand on the Adobe site as a product approved for me until I did it online.

• Satellite 2450 S203: registration issue

  I am the owner of a Satellite 2450 S203 and I can't find it on the recording of "my computer"? any idea?

  Hello

  You can try other toshiba sites around the world. Start with toshiba.com, I don't know where you are, but for example, I am from Turkey and my satellite SA30-303 does not appear in the U.S. site. This can be the same kind of problem. Some models of satellite are not sold in some countries I think.

  In addition, yet once I'm not sure of your model of satellite, but you can see the discontinued models.

  Kind regards
  Halin

• Line-In with Satellite P100 registration issue

  I am trying to use the Line-In port on the front of my P100 to record a signal from a turntable to cassette

  In the recording devices (driver C-Media)

  No - can see MIC (the internal)

  When I put the plug into the port of Mic Microphone (external) is enabled, and Line In shows as currently unavailable

  When I put the Line In port I get the same Jack

  : S

  Ideas please how to configure to use the Line In input for this?

  Thanks for any help

  Tim

  Hmmm have you checked the sound settings in Control Panel-> sound and peripheral Audio?
  There are two different options; Recording and playback.

  You should choose the record and must go through the simple controllers.
  Maybe some are not enabled

  Finally and above all a reinstalling the audio driver is always recommended.

  Good luck

• Registration issue of guarantee (from 1 year to 3 years)

  Hello

  A few days ago, I bought a Toshiba Tecra laptop with additional guarantee (which extends the standard warranty of 3 years pick-up & return [SE5353BN-P]).
  When I registered the warranty I got a message that my laptop is less than 1 year warranty & service (Service [B SE5351BN]: 1 year Pick-up & return in the Benelux countries).
  There is no extended warranty more. I bought the above extension, but I can't extend the warranty to 3 years...
  How I solve the problem?
  How can Toshiba service help me?

  > There is no extended warranty more. I bought the above extension, but I can't extend the warranty to 3 years...

  I'm not quite sure what warranty services are available for your model of laptop, but you should check this on Toshiba European page m.
  http://EU.computers.Toshiba-Europe.com/

  That's devices & Services-> Services-> extended warranty

  All the information about your warranty for your laptop can be found here:
  www.Toshiba-tro.de/unitdetails

• Satellite A500-138 - warranty registration issue

  Hello world!

  I'm the Romania... I bought a Toshiba laptop a500-138 Date 11/09/2010...
  They told me that I have a 'no' matter what guarantee, if I subscribe to the laptop on the internet...
  within 3-5 days (or something like that)... of the day, I bought the laptop...

  I tried to record and nothing... when I get the serial number only. and part number I have recived a message that: we're sorry, it seems that there is a problem, save your PC Toshiba laptop (part - SESAME-01300JR3, serial number - XXXXXXXX).
  After 2-3 months, the edge of my monitor plastic was take off my display screen

  Here is an attachment with a photo
  http://i301.Photobucket.com/albums/NN51/atmo_01/07032011004.jpg

  Oh
  And in January I was the official representative of the Romania of Toshiba computers Scoop and they told me that I have no records of my laptop and I can't use the 'anything' guarantee

  And that the plastic of my laptop is not in stock guarantee
  What should I do?

  I put t know when you tried to save your laptop, but when you saw this post on the registry has failed, why you didn't contact Toshiba and report it.
  Try to contact Toshiba in your country, explaining the situation and we hope they will help you.

  Touch wood!