Version 6.1 of Windows Movie Maker in Windows vista does not burn my dvd. We know what could be the problem?

Similar Questions

• Windows Vista does not recognize my DVD player. It is a Pioneer DVD - RW DVR - 110 d ATA Device.

  I looked at the information system and noted that there is a device error.  After checking for a solution online, this is the message I got:

  Windows was able to successfully install device driver software, but the driver has encountered a problem when he tried to run. The problem code is 39.

  Hello

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Hope these helps.

  Rob - bicycle - Mark Twain said it is good.

• Windows Vista does not start to change from IDE to AHCI in the BIOS

  Hi, I spent a lot of time to look at this problem online. I can't find a lot of google search results and they seem to say enter REGEDIT and change the "msahci" start to 0 and even the 'pciide', or 'iaStorV' start parameters to 0. But this does not work for me. The loading Windows with the loading bar screen Green just continues to go wrong and never Windows startup. I have Windows Vista Home Basic Edition.

  I saw someone in this forum with a similar problem but they have upgraded to Win7 on a new installation to fix the problem, they spend on AHCI RAID. I contacted Intel technical support and they said to try HP or the manufacturer of the motherboard. I contacted Intel because I installed a 520 Intel Solid State Drive series and wanted to know if they had a driver to get the benefit of the AHCI instead of the IDE. I know that a lot of people recommend a new installation of Windows, but I don't have a Windows cd with this computer (my computer is here: http://support.hp.com/us-en/document/c00835809 )

  I tried to install this Microsoft fix too. http://support.Microsoft.com/kb/922976

  I wonder if there is an AHCI driver, can I install it or what I can do to get the job of AHCI?

  Thanks to anyone who can help!

  I suggested that you create disks because you said that the computer came with any one and you could not re - install Windows as suggested a possible solution. With these records, you can the recovery of the system back to a factory State. Since you want to install a SSD or change a BIOS setting, these are the changes which can damage the system and require the use of recovery disks.

  If you want a Windows Vista 'clean' no HP Setup, please see Paul's response in this thread of the forum called "System Restore not working not not for HP Media Center Desktop PC. According to his instructions is expected to create a bootable Windows Vista installation disc. My only amendment to this method, is not to use the product key Microsoft Windows Vista on the COA on the side of your computer. Instead, I would like to "Save" the product key from factory OEM HP and HP OEM certificate using ' the Activation, backup and restore ' then 'restore' the certificate and the key to the new clean install of Vista. This will result in an installation clean factory activated that does not require Microsoft to activate. Be aware that the software HP added value will no longer be on your computer. If you want to use this software, you MUST create your personal HP recovery disks and copy the "SWSETUP" folder on your current installation of factory to an external support.

  Re-install Windows Vista, as shown above with the SATA BIOS settings set on AHCI you like will work 100% of the time. It should also install to SSDs, where HP recovery discs are known to fail.

• create dvd Windows Vista does not burn, saying that the disk is not writable

  WINDOWS DVD MAKER on VISTA.  Don't burn the disk.  Teling guard me drive is not a writable disc, but I know that it IS writable.  I dropped the slides, yet will not burn.   I gave up the video, still will not burn.  I gave up the audio, still will not burn.  I tried to burn with a single (audio, video or slides) and still no combustion.  Can anyone help?

  Disable all filters may be worth a try... see the following article:

  How to burn DVDs with Windows DVD Maker
  http://www.7tutorials.com/how-burn-DVDs-Windows-DVD-Maker
  (scroll down for...) What to do in case of problems)

  Maybe you have a problem with the hardware with the optical drive itself.

  Are you able to burn DVDs using other software?

  The following free DVD creation software can be worth a try:

  (FWIW) It's always a good idea to create a system
  Restore point before installing software or updates)

  DVD Flick
  http://www.videohelp.com/tools/DVD_Flick
  (the download is: "dvdflick_setup_1.3.0.7.exe")
  (Download from (direct link) is the fastest).

  Save the file to your desktop or a folder on your
  hard drive and install from there.

  Be sure to read the Guide:
  http://www.dvdflick.NET/Guide.php

  Tutorials:

  Tutorial DVD Flick
  http://beginwithsoftware.com/videoguides/DVD-flick-Guide.html

  Burn any Format video DVD PC
  http://www.freevideoworkshop.com/dvdflicktutorial.htm

  AVI to DVD with DVD Flick Guide
  http://www.Digital-Digest.com/articles/AVI_to_DVD_using_DVD_Flick_page1.html

  To create a video DVD base that should play in most
  free-standing DVD players... try the following...

  First... read the DVD Flick Guide to familiarize
  with the program.

  Open DVD Flick and insert a blank DVD in your drive.

  If the window of Autorun from your computer... just close it.

  Click the project settings button and check... Video /.
  Target format... residents United States... Choose... NTSC /.
  Accept.

  The title button left click Add and navigate to your
  Video clips and select the ones you want on the DVD.

  You can have by selecting one and then use
  the up and down buttons.

  Left click on the button create DVD / OK / Yes / Yes.

  Please wait while the DVD is created.

  When the text "Completed successfully" is displayed you
  DVD Flick can close. Now you can eject your DVD
  and play in your DVD player.

  At some point you might want to buy more
  software advanced as Sony, Cyberlink, Nero, Roxio,
  Ulead, etc... but at least it is a start.

  Good luck.

• Windows VISTA does not start - shows a green bar horizontal scrolling forever, safe mode stops at crcdisk.sys

  Windows Vista does not start.  It shows the horizontal scrolling green bar with microsoft (c) and then goes to a black screen with the mouse arrow that moves. Start in safe mode loads the drivers to the extent of the crcdisk.sys but meet once again at the black screen with the mouse arrow.   Have not the SATA drives connected.  Impossible to get to the command prompt to delete all files.  No work from safe mode.  Restore computer does not work.  I have looked at other posts regarding the renaming/deleting files, but cannot get to the command prompt to resolve this problem.  The computer is less than 2 years.

  Toshiba Satellite A205-S5831, dual processor running.  Running Windows Vista BASIC.  Hard drive seems to work, lighting, well working properly, no error at startup.  No perifpherals or a mouse, or a USB attached.  Disabling USB does not boot.

  Can someone give a help?

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  How to get Vista recovery Media and/or to use the Vista recovery Partition on your computer.

  There is no Vista free download legal available.

  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > find the latest Vista drivers for it > download/install the

  See you soon.

  Mick Murphy - Microsoft partner

• Halo 2 for windows vista does not work on my windows 7. Saiys it cannot start the direct customer

  original title: Halo 2 for windows vista

  Halo 2 for windows vista does not work on my windows 7.  Saiys it cannot start the direct customer.  It will not work in single user either...

  Hello

  Plase make sure you have the latest version of the GFWL Client installed:

  http://www.Microsoft.com/games/en-us/live/pages/livemarketplace.aspx

• My update of Windows media player in windows vista does not play a mkv file.

  * Original title: about file mkv

  My update of Windows media player in windows vista does not play a mkv file, what do I do

  There are solutions out there, depends on how much you trust the software that you download. Here is an example for Windows 8, could work for vista too - make sure you have a full backup and AV before you start :)

  http://www.AddictiveTips.com/Windows-Tips/how-to-play-MKV-files-in-Windows-Media-Player-in-Windows-8/

• Windows Vista does not start upward, with success since the closure complete

  Hello world

  I actually had this problem for a long time, but I'm just now to a point where I'm ready to take a lead in fixing it.

  I can't identify when it started, but Windows Vista does not start upward, with success of a full stop. He gets to the screen where, in general, the green bars will travel across the screen, but the green bars will not come. The screen looks dim and sits there, with the text of the copyright of Microsoft Corporation. So, after not having on the mound, I have to manually shut down the computer by holding down the power button. When I try to start again, told me to go through the Startup Repair tool. If I jump the repair, I just have to meet the same problem - a computer that will not go beyond the screen "green bar".

  So, I do the Startup Repair, and told me what I do for the restoration of the system. Windows starts normally after the restoration.

  Don't forget, this happens from a full stop. To remedy this, I just never completely shut down my computer. I left running and back just at the beginning of the day. The computer may start restart, it just may not start with a full stop.

  Given the start of repair takes, literally, around 4 or 5 hours of full stops complete, accidental or power outages are a nightmare, I am obliged to wait 5 hours to get access to the computer. Fortunately, I have my laptop.

  If someone has encountered this? I saw people talking about the loop of startup repair, but that's not the point, I have. I have yet to see any discussion of my specific problem.

  Thanks in advance!

  Hello

  4-5 hours to do a startup repair is too long.

  Often you get better results if you a using a DVD of Microsoft Vista startup repair.

  Jose how to do a startup repair, etc. using a DVD of Vista from Microsoft

  Manufacturers recovery disks normally do not have Service Options; they are normally a relocation to the factory only settings option.

  Here is the guide to repair Options using a Vista DVD from Microsoft.

  If a friend or a work acquantance of yours has one, you can borrow and use it for repairs.

  http://www.bleepingcomputer.com/tutorials/repair-Windows-with-Windows-Startup-Repair/

  Table of contents

  1. Overview of Windows Vista repair options
  2. How to perform an automatic repair of Windows Vista using Startup Repair
  3. Advanced Tools Overview
  4. Conclusion

  If you do not or can not borrow a Microsoft DVD there is a download of a file ISO of Vista Startup Repair available that you can put on a Bootable floppy to make the above startup repair and that the method is recommended by a large number of posters in these Forums.

  Unfortunately, you have to buy it.

  Here is a link to it:

  http://NeoSmart.net/blog/2011/Windows-Recovery-discs-updated-reinstated/

  See you soon.

• Windows Vista does not recognize my Ipod Touch

  Windows Vista does not recognize my Ipod at all. He even appears in Device Manager. I know that is not my USB cable because it is new, and it isn't my Ipod because it works on Mac computers. I just need someone with expertise to help me get my computer to recognize my Ipod so I can go back to enjoy my music.

  Hello

  MTP mode for WMP11 sync - mode MSC to treat the MP3 as a reader. So you have set up in the MTP.

  -----------------------------------------
  If necessary:

  Tips for solving problems of USB devices - and a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

  Make sure that Windows is updated appropriately that there have been several USB updates.

  1 check that the driver letters for them, for a player, if the drive of the default drive letter is changed, what is happening.
  Mine was h: I added a device that took H: and the player stopped. So I put it back to H: and the other
  device to J: and everything worked again. If necessary start - type in the area of research-> disk management find top
  -Right-click on it - RUN AS ADMIN

  Don't forget to remember the MP3 must be set to the PSG to sync with WMP, and meteorological service of Canada to copy and delete files
  and update the firmware.

  If no joy follow these steps:

  You may need a powered hub. (all the USB ports on your computer are not powered, often only 2)

  Try these:

  Make a Restore Point

  Control Panel - Device Manager - click in the empty area - VIEW - show hidden devices

  Here, your devices are the MP3 player.

  Now look everywhere EXCEPT the USB controllers for your devices (cannot be found) and if you find
  It RIGHT CLICK and UNINSTALL all.

  now go to the USB and UNINSTALL ALL controllers in the category, but the category itself.

  APPLY/OK

  RESET

  This refresh battery USB and hopefully it will allow the unit to install. (You may need a powered hub)

  Here is the similar procedure under XP, Vista is the same, except that we need clear specific devices, as appropriate.
  http://support.Microsoft.com/kb/310575

  This is a utility to help you, but do 1 above.

  USBDeview is a small utility that lists all USB devices currently connected to your computer, as well as all USB devices that you previously used. Run Options and check the 1st three choices to see if one is there.

  http://www.NirSoft.NET/utils/usb_devices_view.html

  You must remove all instances of the devices and restart.

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• I try to install yahoo mesengerand it keeps giving me a pop-up Microsoft Windows.The error is the following: could not initialize properly (0xc0150002). What could be the problem?

  I try to install Yahoo Mesenger and it keeps giving me a pop-up Microsoft Windows.The error is the following: could not initialize properly (0xc0150002). What could be the problem?

  Hello DennisUSMC,

  Look at the thread in Yahoo Answers.
  http://UK.answers.Yahoo.com/question/index?QID=20091129190055AA1nEsp

  He suggested to uninstall other versions of Yahoo messenger before installing the latest version. If it does not help to solve your problem, then go to Yahoo support.
  http://help.Yahoo.com/kb/index?locale=en_US&page=product&y=PROD_MSNG&PIR=qWKr06VibUkWf.Qpynpw1MiIKLy_mnW1Xh_iz.es9b2DJRQQvLHTQmI

  Sincerely,

  Marilyn

• Windows Vista does not work - cannot open Control Panel control and IE

  original title: Windows Vista does not work properly.

  Hello

  I have Windows Vista Home Premium running on Lenovo laptop. Recently, I cann't open the browser IE, the same panel. I don't have a Vista CD. But I have the product key provided with the laptop. Please, help me to make it fully operational as before.

  Assuming that you can always connect to your computer in normal mode:

  Run a check of the filesystem to find corrupted files and repair them if possible.

  Start button > Search box type cmd > look up, do a RIGHT click on cmd.exe > click run as
  Administrator > in this window type cmd black and white, on the
  flashing fast sfc/scannow > press the ENTER key.
  Note: there is a space between
  'sfc' and ' / '.
  To sit and wait. It will take time.
  When finished, exit the cmd window.
  Reboot (restart your computer)

  After that, check if you can run the computer as well as to access the IE.
  If IE still does not work, use the following tutorials...

  1 Internet Explorer does not start or stop responding
  http://support.Microsoft.com/kb/926449
  Note: It has an auto FixIt application. Use it.

  2. Internet Explorer Add - ons problem when IE hangs or freezes
  http://support.Microsoft.com/mats/ie_freezes_or_crashes/en-us
  Note: there also an Fix It self.

  3. to resolve network connectivity problems in Internet Explorer
  http://support.Microsoft.com/kb/936211

• Windows Vista does not start after installing Linux OS

  original title: Windows Vista does not start after the installation of the Linux OS... Help!

  I installed Fedora 10 Red Hat Linux on my HP laptop and now each time it powers on, I can't do vista windows at startup.  Goes directly into Linux.

  I need to get back to normal.  Any help would be appreciated.

  I installed Fedora 10 Red Hat Linux on my HP laptop and now each time it powers on, I can't do vista windows at startup.  Goes directly into Linux.

  I need to get back to normal.  Any help would be appreciated.

  Hey Oscar Jose

  Download the correct ISO file and make a disk bootable from the link below

  Then use the Startup Repair option when you start from

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  or at startup press F11 to start the process of restoration of hp and see if you can reinstall vista from the recovery partition and place your machine, back to the way you bought

  warning you all data loss and 3 third-party programs that you have installed unless there is a non-destructive option in your hp recovery options

  Thirdly try to ask in a fedora forum to solve the problem, he has caused

  http://fedoraproject.org/

  Walter, the time zone traveller

• Windows Vista does not start, turns to a blue screen error 2203

  original title: Windows Vista does not start, turns to a blue screen HELP PLEASE!

  Help, please! So I'm panicking here, just yesterday, I tried to download the update to Itunes, and it did not work. So I followed the instructions and uninstalled the program first, but one of the applications does not uninstall correctly. I thought I could just substitute with the update and replace. The error code was 2203.

  So I thought it was right after the download all itunes thing, and when I came back to check on the download, the screen turned to this black thing with words on this subject. I decided to force closing down by pressing the power button. Now everytime I turn on the computer, it leads to the screen saying 'windows is loading files', then this blue screen with a very large arrow (the mouse). I tried pressing the F11 key and stuff, but I have no idea what to do. PLEASE REPLY AS SOON AS POSSIBLE, REALLY NEED A COMPUTER!

  "I tried to do the second option, because the first really helped."

  Something works, or it doesn't work regarding: "really helped."

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  I'm sorry, but I don't understand where the procedure of ISO part 2 stops.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  You may be interested in this:

  Vista recovery media obtain and/or use the Partition Recovery Vista on your computer to the factory settings .

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Also ask them if it is possible to do the recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.

  They will tell you how to do this.

  Every computer manufacturer has their own way of making recovery disk/s.

  See you soon.

  Mick Murphy - Microsoft partner

• Windows Vista does not start - only Safe Mode

  Hello

  Windows Vista does not start. Starts only in Mode safe. Same system of recovery is not backward by date

  Press F8 all turn the laptop.
  Choose the first option: by computer repair and try to repair the operating system automatically.

• Satellite L30-105 (PSL33E) Windows Vista does not see the DVD - ram UJ-850 s

  Hello

  I have a Satellite L30-105 (PSL33E) with windows Vista. Windows Vista does not recognize the DVD - ram. BIOS recognize DVD-ram. I tried to download the drivers for the DVD-ram, but they are not on the side of Toshiba.

  Who can help me to get the right driver or learn more? Problems with the carpet * a DVD-ram uj-850 s ATA device and windows Vista.

  Hello

  The CD/DVD drive needs no special drivers!
  Vista includes a Microsoft driver that works with all CURIOUS s (CD/DVD drives)

  Simply said, the Vista should recognize the drive without any problems.

  A few questions; did you get any error messages? What is the status of Device Manager? Do you see yellow exclamation points?

  There is an old way to correct a similar drive problem. It worked on XP then try it on Vista OS.
  It of necessary to update the registry entry
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  1. click on the start menu.
  2. If it is a Vista machine in the search box type regedit without quotes.
  3. look for the registry key mentioned above.
  4. in the right panel you'll see something along the lines of UpperFilter and UpperFilter you want to click on each key filter and tap on delete. Click Yes when asked to confirm if you want to delete the key.
  5. restart Windows.
  6 let me know if it works.