version SATA sr1500nx

I am considering the purchase of a 120GB Kingston SATA III SSD that is compatible with SATA 2.  I know that there are two SATA connectors on the motherboard, but I can't find information on what SATA version they support (hardware and bios).  Original SATA? or SATA 2?  The BIOS of the PC is a version of 2005 which preceded the introduction of SATA 3 and I do not think that the SATA2 spec lead until possibly early 2005?

Here are the specifications of your desktop Compaq Presario SR1500NX and its card mother A7V8X-(Kelut). According to this information, this model uses a VIA KM400A northbridge and VIA VT8237 southbridge chipset. VIA VT8237 southbridge is responsible for the communication of the IDE/SATA and is limited to SATA revision 1.0 with data rates 1.5 Gbit/s - 150 MB/s.

Please send Bravo

Tags: HP Desktops

Similar Questions

  • "Reading DMA Ext" SMART error reported for a 27 "Mac (model end 2013)

    Hello

    I have experienced a strange behavior in last week, where my iMac starts upward normally, but directly obtained subsequently very slow and lazy. Each program showed the wait mouse cursor und switch between programs by using the Task Manager did not work. If available, I could click through the mouse on a different program of an application window, but only to bring in the und before then the wait cursor shown here as well.

    I had to reboot several times, until all behaved as usual.

    I checked the State of the disk hard und SMART monitor indicated failures during the power on unit (UNC at LBA). And it seemed that this error has occurred several times (once at the start of the iMac, I retried several times).

    I installed the tool console smartctl to get more detailed information and it reported an error count of 534 where were the last 4 errors of this type (history does not seem to store more errors). The last error reported was of type READ FPDMA queued (global error at LBA UNC).

    I ran a SMART long test, which passed without error.

    And if the system boots properly, there is no indication that the hard disk has a problem.

    Someone knows something similar and has a suggestion, what to do? Is there something wrong with the hard drive, controller, plugging in the cable?

    I really appreciate your thought and suggestions about this strange behavior.

    Thank you for your support in advance!

    Best regards

    René

    Here some information copied from the smartctl journal:

    ----------------------------------------------------------

    = START OF SECTION INFORMATION =.

    Phone model: APPLE disk HARD ST1000DM003

    Serial number: S1DCF1AX

    LU WWN device ID: 5 000c 50 061b9b612

    Firmware version: AP18

    [User capability: 1,000,204,886,016 1.00 TB bytes]

    Sector size: 512 byte logical, physical 4 096 bytes

    Rotation speed: 7200 RPM

    Form factor: 3.5 inches

    Device is: not in smartctl database [for details: showall - P]

    ATA Version is: DCC-2, 3-ACS T13 / 2161 - D revision 3B

    SATA version: SATA 3.1, 6.0 GB/s (current: 3.0 Gb/s)

    Local time is: Sun Jul 10 12:04:36 CEST 2016

    SMART support is: available - device has SMART capability.

    SMART support is: enabled

    = START OF SECTION ERROR =.

    Error 534 to disk works to life: 6143 hours (255 days + 23)

    When the command that caused the error occurred, the aircraft was active or inactive.

    After the completion of the order has occurred, the registers were:

    ST ST SC SN CL CH DH

    -- -- -- -- -- -- --

    40 51 00 70 b4 76 01 error: UNC at LBA = 0x0176b470 = 24556656

    Orders, leading to the command that caused the error were:

    CR EN SC SN CL CH DH DC Powered_Up_Time command/Feature_Name

    -- -- -- -- -- -- -- --  ----------------  --------------------

    25 00 20 70 76 41 00 00:27:49.218 LU DMA EXT b4

    25 00 20 70 76 41 00 00:27:45.476 LU DMA EXT b4

    25 00 20 70 76 41 00 00:27:41.811 LU DMA EXT b4

    25 00 20 70 76 41 00 00:27:38.207 LU DMA EXT b4

    25 00 10 88 08 40 00 00:27:38.204 LU DMA EXT c6

    ...

    Error 530 to disk works to life: 6143 hours (255 days + 23)

    When the command that caused the error occurred, the aircraft was active or inactive.

    After the completion of the order has occurred, the registers were:

    ST ST SC SN CL CH DH

    -- -- -- -- -- -- --

    40 51 00 70 b4 76 01 error: UNC at LBA = 0x0176b470 = 24556656

    Orders, leading to the command that caused the error were:

    CR EN SC SN CL CH DH DC Powered_Up_Time command/Feature_Name

    -- -- -- -- -- -- -- --  ----------------  --------------------

    60 00 20 70 76 41 00 00:27:34.254 LU FPDMA queued b4

    60 00 10 88 08 40 00 00:27:34.254 LU FPDMA queued c6

    60 00 10 18 22 20 40 00 00:27:34.254 READ FPDMA QUEUED

    60 00 10 a8 c7 1 d 40 00 00:27:34.254 READ FPDMA queued

    60 00 08 ff ff ff 4f 00 00:27:34.150 READ FPDMA queued

    It's a lot of information that virtually no one knows what to do with... but my guess is that everything points to a failing hard drive.

  • HP Pavillion DV6700: Is my HP Pavilion DV6700 Compatible with SSD?

    I would like to know if my HP laptop is compatible with SSDS. An Internet search turns postings that say that it is possible and other thay say my PC is not compatible with SSDS.

    Here is some info on my installation.

    My PC is a HP Pavilion DV6700 CTO Entertainment Notebook
    I am running Windows 7
    The PC came with Windows Vista

    The BIOS is Hewlett - Packard l58 2008-06-16
    The processor is Intel Core Duo CPU T7500 to 2.20 GHz, 2201 Mhz, 2 carrots, 2 logical processors

    The new SSD is a Samsung SSD of 850 EVO.

    (1) my PC is compatible with SSDS?

    (2) are there updates the BIOS or the settings of the software that I need to know?

    Thanks for any advice.

    Yes, it is a fully native SATA (ahci) system and an SSD works perfectly. With Windows 7 operating system will know it is a SSD and activate the TRIM and other optimizations to the SSD. It will be a version SATA slower that curent models but you still benefit greatly from an SSD. You must update the BIOS on this model, but not because of the SSD. There isn't quite enough important updates BIOS for this model which correct some problems of initial material as the fan operation and resume the suspension.

    If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

  • Satellite A200 - 1 M 8 XP installation has failed

    Right time of the day) I recently purchased laptop Satellite A200 - 1 M 8. Wiped vista thanks 7.0 version sata driver successfully,
    but this does not work for me again. XP continues, I say it do not format, he asks new driver and won't even try to read my floppy USB drive.

    Ok.. I tried to integrate the drivers with nLite (added a folder with the same sata drivers), it does not work too.
    System still wants driver to see the hard drive at the beginning and this time when he reached the moment of shaped.
    He 'cannot copy' one of the files in the drivers folder. If I escape, I have blue screen "stop" during the 1st load of windows. 7.5 version causes
    "unexpected error" and won't load at all.

    Do I did wrong? I'd appreciate any help!

    Hello

    I think you just try to install a bad driver. You need to install the Intel Matrix Storage manager.
    On the Toshiba driver page, you will find the Storage Manager 7.5.0.1017 version.

    The Sat A200 - 1 M 8 belongs to the series of PSAE6 so please choose the right!

    I think you need to enter the BIOS and should define the default BIOS settings, and save the changes.
    Then try to install the Intel Matrix Storage Manager using the F6 key during the XP installation.

    On my laptop it worked properly. So I see no reason why it should not work on your laptop!

    Best regards

  • Drive internal 3 Gbps instead of 6 reports

    A late 2014 27 "/ 5 k has one internal Seagate Barracuda (ST1000DM003) that reports a SATA 3.0 GB/s version. shouldn't it be 6 Gb/s?"

    SATA version: SATA 3.1, 6.0 GB/s (current: 3.0 Gb/s)

    Why do you think that one 6 Gb/s?

  • I tried running sfc/scannow and it does not - it keeps asking me for a CD and my CD in the CD tray

    I am running XP Pro SP3.  I had to buy a Windows Genuine Advantage XP SP2 CD 3 years agao, because I bought a computer with an invalid CD... He was surprised when I ran the WGA tool. I ran sfc/cannow tool, but when I insert my CD of XP WGA (including SP2), I am invited to a different CD. Now, I get errors in my log window update such as:

    09/10/03 12:25:18:289 1360 f54 Agent WARNING: is not Installable rule, updateId = {A11FFEA5-BFFC-43E1-9A02-99970CC142C8}.101, hr = 8004100E
    2010-09-03 12:25:18:360 1360 f54 Agent WARNING: is not Installable rule, updateId = {AFAFB0D2-064F-4B3B-A5F6-8FEB0BFAB287}.100, hr = 8004100E
    2010-09-03 12:25:18:440 1360 f54 Agent WARNING: is not Installable rule, updateId = {0418B8A1-016E-4BA9-9688-5E0BE64CA97B}.100, hr = 8004100E
    2010-09-03 12:25:18:600 1360 f54 Agent WARNING: is not Installable rule, updateId = {BC19109A-8D10-4CDE-8383-A90BACB8608C}.100, hr = 8004100E

    and the WBEM LOG entries such as:

    ABSENT. JOURNAL

    (Sat Sep 04 21:17:56 2010.1034447): GetUserDefaultLCID failed, restorting to system version (Sat Sep 04 21:18:04 2010.1041587): GetUserDefaultLCID failed, restorting to system version (Sat Sep 04 21:18:05 2010.1043210): GetUserDefaultLCID failed, restorting to system version (Sat Sep 04 21:18:09)

    FRAMEWORK. JOURNAL:

    announcement: 2808 [d:\xpsp\admin\wmi\wbem\sdk\framedyn\wbemglue.cpp.2252]
    Warning the connection - provider with this name already existed, substituted with last supplier login (root\cimv2:Win32_ComputerSystemWindowsProductActivationSetting) 04/09/2010 22:28:32.357 phone: 376 [d:\xpsp\admin\wmi\wbem\sdk\framedyn\wbemglue.cpp.2252]
    Warning the connection - provider with this name already existed, substituted with last supplier login (root\cimv2:Win32_ComputerSystemWindowsProductActivationSetting) 04/09/2010 22:38:06.082 phone: 908 [d:\xpsp\admin\wmi\wbem\sdk\framedyn\wbemglue.cpp.2252]
    Warning the connection - provider with this name already existed, substituted with last supplier login (root\cimv2:Win32_ComputerSystemWindowsProductActivationSetting) 04/09/2010 22:52:40.029 wire: 2792 [d:\xpsp\admin\wmi\wbem\sdk\framedyn\wbemglue.cpp.2252]

    WBEMPROX. JOURNAL:

    (My Sep 04 22:48 2010.6437666): NTLMLogin gave rise to hr = 0x8004100e
    (My Sep 04 22:48 2010.6438167): NTLMLogin gave rise to hr = 0x8004100e
    (My Sep 04 22:48:01 2010.6438598): NTLMLogin gave rise to hr = 0x8004100e
    (My Sep 04 22:48:01 2010.6438658): NTLMLogin gave rise to hr = 0x8004100e
    (My Sep 04 22:48:01 2010.6438958): NTLMLogin gave rise to hr = 0x8004100e

    WBEMESS. JOURNAL:

    (My Sep 04 15:07:26 2010.96608095): has not issued an event consumer to the NTEventLogEventConsumer = "Journal of SCM consumer events" event with error code 0 x 80041003. Event of a fall.
    (My Sep 04 15:07:27 2010.96609166): a fall events to be event NTEventLogEventConsumer = "Journal of the events of SCM consumer" consumer in the space of //./root/subscription names
    (My Sep 04 15:07:27 2010.96609166): has not issued an event consumer to the NTEventLogEventConsumer = "Journal of SCM consumer events" event with error code 0 x 80041003. Event of a fall.
    (My Sep 04 15:07:28 2010.96609727): a fall events to be event NTEventLogEventConsumer = "Journal of the events of SCM consumer" consumer in the space of //./root/subscription names
    (My Sep 04 15:07:28 2010.96609737): has not issued an event consumer to the NTEventLogEventConsumer = "Journal of SCM consumer events" event with error code 0 x 80041003. Event of a fall.
    (My Sep 04 21:05:05 2010.263068): use of NT event log: could not retrieve sid, 0 x 80041002
    (My Sep 04 21:05:06 2010.263679): use of NT event log: could not retrieve sid, 0 x 80041002
    (My Sep 04 21:05:06 2010.263829): use of NT event log: could not retrieve sid, 0 x 80041002
    (My Sep 04 21:05:07 2010.264600): use of NT event log: could not retrieve sid, 0 x 80041002
    (My Sep 04 21:05:11 2010.268926): use of NT event log: could not retrieve sid, 0 x 80041002
    (My Sep 04 21:05:13 2010.271310): use of NT event log: could not retrieve sid, 0 x 80041002
    (My Sep 04 21:05:29 2010.286792): use of NT event log: could not retrieve sid, 0 x 80041002
    (My Sep 04 21:12:04 2010.682381): use of NT event log: could not retrieve sid, 0 x 80041002
    (My Sep 04 21:19:23 2010.1120711): use of NT event log: could not retrieve sid, 0 x 80041002
    (My Sep 04 21:19:26 2010.1123815): use of NT event log: could not retrieve sid, 0 x 80041002
    (My Sep 04 21:40:02 2010.2359813): use of NT event log: could not retrieve sid, 0 x 80041002
    (My Sep 04 22:05:07 2010.3865077): use of NT event log: could not retrieve sid, 0 x 80041002

    WMIPROV. JOURNAL:

    (Sat Oct 02 08:03:06 2010.351064): WDM call returned error: 4200
    (Sat Oct 02 08:05:46 2010.511385): WDM call returned error: 4200
    (Sat Oct 02 08:05:50 2010.514690): impersonation failed - access denied
    (Sat Oct 02 08:05:50 2010.514860): impersonation failed - access denied
    (Sat Oct 02 08:11:19 2010.844223): impersonation failed - access denied
    (Sat Oct 02 08:12:20 2010.905251): impersonation failed - access denied
    (Sat Oct 02 15:18:29 2010.365525): WDM call returned error: 4200
    (Sat Oct 02 15:19:10 2010.405963): WDM call returned error: 4200
    (Sat Oct 02 15:19:11 2010.406694): impersonation failed - access denied
    (Sat Oct 02 15:19:11 2010.406704): impersonation failed - access denied
    (Sat Oct 02 15:23:30 2010.666568): impersonation failed - access denied
    (Sat Oct 02 15:25:01 2010.757198): impersonation failed - access denied
    (Sun Sep 03 12:23:13 2010.354629): WDM call returned error: 4200
    (My Sep 04 21:06:39 2010.357403): WDM call returned error: 4200

    I don't know that this is not what you want to hear.  However, from the beginning of your notes, you said that the system was installed with an invalid Windows operating system CD and since you bought Windows XP SP 2, which is the authentic product.  If I am wrong please correct me.

    If you try to run SFC scannow from Windows XP SP2, you will continue to receive the request for the additional CD cover Service Pack 3.

    If you have two options:

    (1) do a fresh install with the Windows XP SP2 and upgrade to SP3 on sites I've proposed below.

    or

    (2) simply download the Service Pack 3 of one of the websites below and use this CD to finish the scannow SFC.

    I think you'd be a lot better off takeing the time to back up all your important documents and files.

    Go to: http://www.gtopala.com/SIW-download.html and download the free version of SIW.

    This will give you at least with all the files and informaition about your device drivers that are currently on your system now.  I had the IT Pro version for years and would be with her.  I know that this version provide you all the keys for any product you may have and no password specified for email or the system.  I know that the free version will not provide passwords, but it can provide you with product keys. If you have lost or misplaced one of your applications can be valuable.  Most of the time, you can download the product if you have the key you're in business.

    Errors that you receive above I think that you are still able to access the internet.  If yes I would like to download the SP3 since

    Microsoft Downloads under: http://www.microsoft.com/downloads/en/details.aspx?FamilyId=5B33B5A8-5E76-401F-BE08-1E1555D4F3D4&displaylang=en it's about 316.4 MB and it may take about 2 hours, but it is worth.

    Of course, once this is done you should be able do a fresh install with the purchased Windows XP Sp 2 now you can install the Service Pack from Windows Update or make a CD from the above address or the ISO image from: http://www.microsoft.com/downloads/en/details.aspx?FamilyID=2FCDE6CE-B5FB-4488-8C50-FE22559D164E.

    I hope this has been helpful.

    The only errors that are really me you listed above were the following.  That's why I take the time to backup and reinstall.

    09/10/03 12:25:18:289 1360 f54 Agent WARNING: is not Installable rule, updateId = {A11FFEA5-BFFC-43E1-9A02-99970CC142C8}.101, hr = 8004100E
    2010-09-03 12:25:18:360 1360 f54 Agent WARNING: is not Installable rule, updateId = {AFAFB0D2-064F-4B3B-A5F6-8FEB0BFAB287}.100, hr = 8004100E
    2010-09-03 12:25:18:440 1360 f54 Agent WARNING: is not Installable rule, updateId = {0418B8A1-016E-4BA9-9688-5E0BE64CA97B}.100, hr = 8004100E
    2010-09-03 12:25:18:600 1360 f54 Agent WARNING: is not Installable rule, updateId = {BC19109A-8D10-4CDE-8383-A90BACB8608C}.100, hr = 8004100E

    Good luck

    E-mail address is removed from the privacy *.

  • I forgot system password Oracle 11 g r2

    A way to recover the sys password in oracle 11 g r2

    Oracle linux 6.6

    ReemaPuri wrote:

    A way to recover the sys password in oracle 11 g r2

    Oracle linux 6.6

    NO, not possible & unnecessary

    [oracle@localhost dbs] $ id

    UID = 500 (Oracle) gid = 500 (oracle) groups = 500 (oracle)

    [oracle@localhost dbs] $ sqlplus / as sysdba

    SQL * more: Production of the 11.2.0.2.0 version Sat Jun 20 10:54:38 2015

    Copyright (c) 1982, 2010, Oracle.  All rights reserved.

    Connected to:

    Oracle Database 11g Enterprise Edition Release 11.2.0.2.0 - Production

    With partitioning, OLAP, Data Mining and Real Application Testing options

    SQL > show user

    The USER is "SYS".

    SQL >

  • Ora-00265 instance recovery required to CCR after immediate cessation

    Hello world

    I have this problem in a database of production, (version 11g 2, 11.2.0.3) using Real Application Cluster, I disabled archivelog to a window for a mass of large tables update, now I'm trying to reactivate the archivelog mode and I couldn't, because it shows the error ORA-00265, I find a lot of sites and Oracle support and the explanation is always the same "you shutdown abort or force start the base of. data start again and stop with immediate or normal option"but the thing is that I use srvctl with the immediate option, I did a few reboots of the database and I read in the newspaper of the alerts that indeed there at the start of the database runs a recovery of Instance.

    Why does this happen? I stop the two nodes at once and one by one, began with sqlplus and I didn't really know what else to do, I hope you can help me.

    Oracle@sur01 # srvctl stop asaa d-i o asaa1 immediate instance

    Oracle@sur01 #. oraenv

    ORACLE_SID = [oracle]? ASAA

    The Oracle base has been set on/u01/app/oracle

    Oracle@sur01 # export ORACLE_SID = asaa1

    Oracle@sur01 # srvctl start database d asaa o mount

    Oracle@sur01 # sqlplus / as sysdba

    SQL * more: Production of the 11.2.0.4.0 version sat Jan 24 15:48:16 2015

    Copyright (c) 1982, 2013, Oracle.  All rights reserved.

    Connected to:

    Oracle Database 11 g Release 11.2.0.4.0 - 64 bit Production

    With Real Application Clusters and Automatic Storage Management options

    Instance Estado Modo Lectura Activa Actividad Blo Inicio Archive?     EstArch

    ---------------- ------------ -------------------- ----------------- --------- --- -------------- ------------ -------

    MOUNTED asaa1 MOUNTED NORMAL ASSET No. 24/01/15 15:47 NOARCHIVELOG ORDER

    SYS@asaa1 > changing archivelog database;

    ALTER database archivelog

    *

    ERROR on line 1:

    ORA-00265: recovery required instance, cannot define in ARCHIVELOG mode

    Thanks in advance...

    Giancarlo Giammaria.

    Hello world

    To share knowledge, I write what I had to do to solve the problem:

    It seems that the FCAC does not correctly close instances (another question to consider), causing the datafile headers remain incompatible with a different number of SCN.

    In the next query, you can see as the checkpoint_change # in v$ database is different from the checkpoint_change # in v$ datafile (this question was scheduled to be executed in mounted State)

    SYS @ > select dbid, name, created, resetlogs_change #, resetlogs_time, open_mode, log_mode, checkpoint_change #,.

    2 controlfile_type, controlfile_change #, controlfile_time

    3 v $ database;

    NAME DBID CREATED RESETLOGS_CHANGE # RESETLOGS_TIME OPEN_MODE LOG_MODE CHECKPOINT_CHANGE # CONTROL

    ------------------------------ ---------- -------------------- ------------------------------ -------------------- -------------------- ------------ ------------------------------ -------

    CONTROLFILE_CHANGE # CONTROLFILE_TIME

    ------------------------------ --------------------

    2103866247 XXX 11 OCTOBER 2014 12:00:07 1 OCTOBER 11, 2014 12:00:07 MOUNTED NOARCHIVELOG 332020165 CURRENT

    332058714 26 JANUARY 2015 22:37:34

    1 selected line.

    SYS @ > select the folder, name, State, checkpoint_change No. # from v$ datafile;

    FILE NAME STATUS CHECKPOINT_CHANGE NO. #.

    ------------------------------ ---------- ------- ------------------------------

    332020165 SYSTEM 1 + DG_DATA/a

    2 + DG_DATA/a 332020165 online

    3 + DG_DATA/a 332020165 online

    Then, the process that I did to fix that and enable archivelog:

    srvctl stop database d immediate o xxx

    srvctl start database d o mount xxx

    recover the database;

    srvctl start database-d xxx (apparently the bd still needs a clean shutdown to reactivate the archives, otherwise the ORA-00265 continues to show, so I had to start and stop)

    srvctl stop database d immediate o xxx

    srvctl start database d o mount xxx

    ALTER database archivelog (at this point, it worked and the archiving log enabled, after this, stop and open again...)

    Hope this helps someone else!

  • Creative Cloud Desktop App uninstall Forever?

    Try to uninstall Creative Cloud Desktop app for Mac because my old version sat for applications loading forever. Uninstallation is now works for eternity too. What is the problem with that? I just want to uninstall all Adobe software and re-install creative cloud and start over.

    Please close creative cloud and rename the file opm.db. Please check Solution 2: clean the connection of the cached user information.

    I hope that it helps to disconnect from this machine.

  • Dreamweaver CS 6 crashing MacBook Pro

    Greetings,

    I recently bought a Mac Book Pro.  After installing my software dev normal I try DW CS6.  So I installed the trial and it was breaking my MBP.  I took it in our Mac guy in College, I work at and they thought maybe a HD problem (is a 750 Hybrid SSD drive) so they went out.  However, I still crash problems.  I have about 10 reports of incidents of the Mac, but also the Console logs.  DW CS 6 (Ver 12 build 5861) is completely updated to FYI, as is the MBP with all the Apple updates.  The MBP will work for days without DW running, but when I start DW it crashes within the hour.

    Here are the specifications of system MBP:

    10.8.2 version

    2.3 GHz Intel core I7

    DDR3 1600 16 GB

    750 GB SATA HD (replacing it for testing)

    Here's the last crash log:

    Interval since the last report of panic: 2342 s

    Panic since the last report: 3

    Anonymous UUID: EDE554DE-DF81-E543-0EBC-81AB7057A366

    Kills Feb 26 13:03:06 2013

    panic (cpu 0 0xffffff800beb7bd5 appellant): Kernel trap at 0xffffff800be2c064, type 13 = General protection, records:

    CR0: 0X000000008001003B, CR2: 0XFFFFFF81DCA0F000 CR3: 0X000000000E8B8000 CR4: 0X00000000000606E0

    RAX: 0XBFFFFF802C36CC40, RBX: 0XFFFFFF802C37A550 RCX: 0 X 0000000000000004, RDX: 0 X 0000000000000001

    RER: 0XFFFFFF81CC884E30, RBP: 0XFFFFFF81CC884E60, IHR: 0 X 0000000000000001, RDI: 0XFFFFFF800C4B9C48

    R8: 0 X 0000000000000002, R9: 0X7FFFFFFFFFFFFFFE, R10: 0XFFFFFF800C4BDC20 R11: 0 X 0000000000000201

    R12: 0XFFFFFF802C37A580, R13: 0XFFFFFF81CBF7D868, R14: 0 X 0000000000000000, R15: 0XFFFFFF802C37A550

    RFL: 0 X 0000000000010046, RIP: 0XFFFFFF800BE2C064, CS: 0000000000000008, SS 0 X: 0 X 0000000000000010

    Lack of CR2: 0xffffff81dca0f000, error code: 0 x 0000000000000000, CPU error: 0x0

    Backtrace (CPU 0), frame: return address

    0xffffff81cc884ad0: 0xffffff800be1d626

    0xffffff81cc884b40: 0xffffff800beb7bd5

    0xffffff81cc884d10: 0xffffff800bece4ed

    0xffffff81cc884d30: 0xffffff800be2c064

    0xffffff81cc884e60: 0xffffff800be2beef

    0xffffff81cc884ea0: 0xffffff800be2bdd8

    0xffffff81cc884ed0: 0xffffff800be3f1fe

    0xffffff81cc884f20: 0xffffff800beab1e9

    0xffffff81cc884f50: 0xffffff800bebd3ac

    0xffffff81cc884f80: 0xffffff800beb7203

    0xffffff81cc884fd0: 0xffffff800bece6a8

    0xffffff81dd773e80: 0xffffff800be2f1c3

    0xffffff81dd773ec0: 0xffffff800be2dc81

    0xffffff81dd773f20: 0xffffff800be2d9f3

    0xffffff81dd773f60: 0xffffff800be3e019

    0xffffff81dd773fb0: 0xffffff800beb26b7

    Corresponding to the current thread BSD process name: kernel_task

    Mac OS version:

    12 C 60

    Kernel version:

    12.2.0 Darwin kernel version: Sat Aug 25 00:48:52 PDT 2012; root:XNU-2050.18.24~1/RELEASE_X86_64

    Kernel UUID: 69A5853F-375A-3EF4-9247-478FD0247333

    Slide kernel: 0x000000000bc00000

    Text of core base: 0xffffff800be00000

    Name of system model: MacBookPro8, 2 (Mac-94245A3940C91C80)

    Availability of the system in nanoseconds: 13004011215965

    last load kext to 2732825614679: com.apple.filesystems.smbfs 1.8 (0xffffff7f8e1fd000, size 229376 addr)

    Finally unloaded kext to 165936857854: com.apple.driver.AppleUSBUHCI 5.2.5 (addr 0xffffff7f8c7dc000, size 65536)

    kexts responsible:

    com Apple.filesystems.smbfs 1.8

    com Apple.nke.PPTP 1.8

    com Apple.filesystems.NTFS 3.10

    com.apple.driver.AudioAUUC 1.60

    com.apple.driver.AppleHWSensor 1.9.5d0

    com.apple.driver.AGPM 100.12.69

    com.apple.driver.AppleMikeyHIDDriver 122

    com Apple.filesystems.autofs 3.0

    com.apple.driver.AppleHDA 2.3.1f2

    com.apple.iokit.IOUserEthernet 1.0.0d1

    com.apple.iokit.IOBluetoothSerialManager 4.0.9f33

    com.apple.driver.AppleIntelHD3000Graphics 8.0.0

    com.apple.iokit.BroadcomBluetoothHCIControllerUSBTransport 4.0.9f33

    com.apple.driver.AppleMikeyDriver 2.3.1f2

    com.apple.Dont_Steal_Mac_OS_X 7.0.0

    com.apple.driver.AppleSMCLMU 2.0.2d0

    com.apple.driver.AppleSMCPDRC 1.0.0

    3.2.11 com.apple.driver.ApplePolicyControl

    com.apple.driver.AppleUpstreamUserClient 3.5.10

    com.apple.kext.AMDFramebuffer 8.0.0

    com.apple.AMDRadeonAccelerator 1.0.0

    com.apple.driver.AppleIntelSNBGraphicsFB 8.0.0

    3.2.11 com.apple.driver.AppleMuxControl

    com.apple.driver.AppleMCCSControl 1.0.33

    com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0

    com.apple.driver.AppleLPC 1.6.0

    com.apple.driver.SMCMotionSensor 3.0.2d6

    com.apple.driver.AppleUSBTCButtons 235,4

    com.apple.driver.AppleUSBTCKeyboard 235,4

    com.apple.driver.AppleIRController 320.15

    com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1

    com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1

    com.apple.BootCache 34

    com.apple.iokit.SCSITaskUserClient 3.5.1

    com.apple.driver.XsanFilter 404

    com.apple.iokit.IOAHCIBlockStorage 2.2.2

    com.apple.driver.AppleUSBHub 5.2.5

    com.apple.driver.AppleSDXC 1.2.2

    com.apple.driver.AirPort.Brcm4331 602.15.22

    com.apple.iokit.AppleBCM5701Ethernet 3.2.5b3

    com.apple.driver.AppleFWOHCI 4.9.6

    com.apple.driver.AppleAHCIPort 2.4.1

    com.apple.driver.AppleUSBEHCI 5.4.0

    com.apple.driver.AppleEFINVRAM 1.6.1

    com.apple.driver.AppleSmartBatteryManager 161.0.0

    com.apple.driver.AppleACPIButtons 1.6

    com.apple.driver.AppleRTC 1.5

    com.apple.driver.AppleHPET 1.7

    com.apple.driver.AppleSMBIOS 1.9

    com.apple.driver.AppleACPIEC 1.6

    com.apple.driver.AppleAPIC 1.6

    com.apple.driver.AppleIntelCPUPowerManagementClient 196.0.0

    com Apple.NKE.applicationfirewall 4.0.39

    com Apple.Security.Quarantine 2

    com.apple.driver.AppleIntelCPUPowerManagement 196.0.0

    com Apple.nke.PPP 1.8

    com Apple.kext.Triggers 1.0

    com.apple.driver.DspFuncLib 2.3.1f2

    com.apple.iokit.IOAudioFamily 1.8.9fc10

    com.apple.kext.OSvKernDSPLib 1.6

    com.apple.iokit.IOSurface 86.0.3

    com.apple.iokit.AppleBluetoothHCIControllerUSBTransport 4.0.9f33

    com.apple.iokit.IOBluetoothFamily 4.0.9f33

    2.2.5 com.apple.iokit.IOFireWireIP

    com.apple.iokit.IOSerialFamily 10.0.6

    com.apple.driver.AppleHDAController 2.3.1f2

    com.apple.iokit.IOHDAFamily 2.3.1f2

    com.apple.driver.AppleSMBusPCI 1.0.10d0

    com.apple.iokit.IOAcceleratorFamily 19.0.26

    com.apple.kext.AMD6000Controller 8.0.0

    com.apple.kext.AMDSupport 8.0.0

    3.2.11 com.apple.driver.AppleGraphicsControl

    com.apple.driver.AppleBacklightExpert 1.0.4

    com.apple.iokit.IONDRVSupport 2.3.5

    com.apple.driver.AppleSMBusController 1.0.10d0

    com.apple.iokit.IOGraphicsFamily 2.3.5

    com.apple.driver.IOPlatformPluginLegacy 1.0.0

    com.apple.driver.IOPlatformPluginFamily 5.2.0d16

    com.apple.driver.AppleSMC 3.1.4d2

    com.apple.driver.AppleThunderboltDPInAdapter 1.8.5

    com.apple.driver.AppleThunderboltDPAdapterFamily 1.8.5

    com.apple.driver.AppleThunderboltPCIDownAdapter 1.2.5

    com.apple.driver.AppleUSBMultitouch 235.7

    com.apple.iokit.IOUSBHIDDriver 5.2.5

    com.apple.driver.AppleUSBMergeNub 5.2.5

    com.apple.driver.AppleUSBComposite 5.2.5

    com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.5.1

    com.apple.iokit.IOBDStorageFamily 1.7

    com.apple.iokit.IODVDStorageFamily 1.7.1

    com.apple.iokit.IOCDStorageFamily 1.7.1

    com.apple.iokit.IOAHCISerialATAPI 2.5.0

    com.apple.iokit.IOSCSIArchitectureModelFamily 3.5.1

    com.apple.driver.AppleThunderboltNHI 1.6.0

    com.apple.iokit.IOThunderboltFamily 2.1.1

    com.apple.iokit.IOUSBUserClient 5.2.5

    com.apple.iokit.IO80211Family 500.15

    com.apple.iokit.IOEthernetAVBController 1.0.2b1

    com.apple.iokit.IONetworkingFamily 3.0

    com.apple.iokit.IOFireWireFamily 4.5.5

    com.apple.iokit.IOAHCIFamily 2.2.1

    com.apple.iokit.IOUSBFamily 5.4.0

    com.apple.iokit.IOHIDFamily 1.8.0

    com.apple.driver.AppleEFIRuntime 1.6.1

    com.apple.iokit.IOSMBusFamily 1.1

    com Apple.Security.sandbox 220

    com.apple.kext.AppleMatch 1.0.0d1

    com.apple.security.TMSafetyNet 7

    com.apple.driver.DiskImages 344

    com.apple.iokit.IOStorageFamily 1.8

    com.apple.driver.AppleKeyStore 28.21

    com.apple.driver.AppleACPIPlatform 1.6

    com.apple.iokit.IOPCIFamily 2.7.2

    com.apple.iokit.IOACPIFamily 1.4

    com Apple.KEC.corecrypto 1.0

    Model: MacBookPro8 2, MBP81.0047.B27 of BootROM, 4 processors, Intel Core i7, 2.3 GHz, 16 GB, MSC 1.69f4

    Graphics card: Intel HD Graphics 3000, Intel HD Graphics 3000, integrated, 512 MB

    Graphics card: AMD Radeon HD 6750 M, AMD Radeon HD 6750 M, PCIe, 1024 MB

    Memory module: BANK 0/DIMM0, 8 GB, DDR3, 1600 MHz, 0x029E, 0x434D534F384758334D314131363030433131

    Memory module: BANK 1/DIMM0, 8 GB, DDR3, 1600 MHz, 0x029E, 0x434D534F384758334D314131363030433131

    Airport: spairport_wireless_card_type_airport_extreme (0x14E4, 0xD6), Broadcom BCM43xx 1.0 (5.106.98.81.22)

    Bluetooth: Version 4.0.9f33 10885, 2 service, 18 aircraft, 1 ports series entrants

    Network service: Wi - Fi, AirPort, en1

    Serial ATA Device: WDC WD7500BPVT-00HXZT1, 750,16 GB

    Serial ATA Device: MATSHITADVD-R UJ - 8à8

    USB device: FaceTime HD camera (integrated), apple_vendor_id, 0 x 8509, 0xfa200000 / 3

    USB device: hub_device, 0 x 0424 (SMSC), 0 x 2513, 0xfa100000 / 2

    USB Device: Hub BRCM2070, 0x0a5c (Broadcom Corp.), 0 x 4500, 0xfa110000 / 5

    USB device: Bluetooth USB Host Controller, apple_vendor_id, 0x821a, 0xfa113000 / 8

    USB device: Apple keyboard / Trackpad, apple_vendor_id, 0 x 0245, 0xfa120000 / 4

    USB device: hub_device, 0 x 0424 (SMSC), 0 x 2513, 0xfd100000 / 2

    USB device: Dell Premium USB Optical Mouse, 0x413c (Dell Inc.), 0 x 3016, 0xfd120000 / 4

    USB device: Receiver IR, apple_vendor_id, 0 x 8242, 0xfd110000 / 3

    Any help would be appreciated!

    Jay

    Sure. Visit this link: http://prodesigntools.com/adobe-cs5-5-direct-download-links.html

    Read the instructions carefully before attempting to download.

    Note: This is not an illegal download site. All downloads occur from Adobe servers. This site lists links since Adobe does not list "previous version" links on them.

    In the meantime, I will ask someone from the DW team to intervene here to help you find a solution to this problem.

  • HP Pavilion p7-1003wb: version for a HP Pavilion p7-1003wb SATA

    I need to replace the hard drive on my old HP Pavilion p7-1003wb (death) and I know it's a SATA drive, but does not know which version of the SATA, it is and sheet product specification for this just States SATA Office under the hard disk specifications. I don't know if this means that it is version 1 (?) or simply they didn't want ad version.

    Hello:

    It will not matter which drive sata hard speed you get, because they adjust automatically to the maximum capacity of the controller.  In other words, you can get a SATA III (6.0 Gbit/s) drive, which runs to the SATA II (3.0 Gbps) speed of the controller.

    I found this link which shows the chipset of the motherboard has your PC is supposed to take in charge up to SATA II (3.0 Gbps drives.

    http://motherboards-reviews.com/ASUS/socket_AM3/M4A785D-M_PRO/ASUS_M4A785D-M_PRO_785G_chipset_specifications.html

  • How to determine SATA Version before installing an SSD

    Hi, I would like to know if my laptop (HP G4-1202AX) would support SATAII/SATAIII interface, if I put in an SSD? I checked Sisoft Sandra if my SATA Port is compatible with any SATAII/SATAIII Interface.

    Here's a screenshot of it.

    Thanks in advance

    Download and run theutility CrystalDiskInfo freeto identify the current disc and see what are the available transfer speeds.  If the speed.

    SATA is a compatible specification down. This means that a SATA3 SSD will work on a notebook of SATA specifications, but only to technical SATA transfer rates. Your mobile phone is supported SATA disksso the answer he's suppost a SSD drive.

    Crystal disk is a utility open source. I suggest doanloading the version without ads.

  • What Version of SATA has the motherboard ASUS M2N68-(Narra2)?

    Hello

    I want to improve my HP a6150de with a SSD desktop PC.
    I'm not in a position to know what SATA version (1, 2 or 3 GB of a.k. 1.5/3.0 or 6.0) comes with my

    ASUS M2N68 - Map (Narra2) mother.

    I have tried several hardware analysis tools, also checked the ausus homepage and the specification on the HP

    Home page (http://support.hp.com/us-en/document/c01080282).

    Does anyone know what version it is? I have colleagues SATA 2 alias 3 GB

    Thank you

    Ivo343

    Hello:

    You guessed it right, but I have no price to give you.

    http://www.nvidia.com/object/mobo_gpu_tech_specs.html

    You will find all the technical specifications for the chipset of the motherboard of your PC in the 3rd column on the right.

  • clean install of Vista on an old drive hard ide after drive failure hard sata - oem version now get "the limited functionality" due to "unauthorized changes" had no problems for 3 years until this!

    I did a clean install of vista on an old drive hard ide after the disk sata hard down - (oem version) now get "feature limited" because of the "unauthorized modification" had no problems for 3 years until this!

    Hello

    It's a shame you don't know the exact name of the virus

    Malware can cause non-genuine messages appear

    but try this:

    Download update and scan with the free version of malwarebytes anti-malware

    http://www.Malwarebytes.org/MBAM.php

    You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes

    http://www.bleepingcomputer.com/download/anti-virus/rkill

    If it does not remove the problem and or work correctly in normal mode do work above in safe mode with networking

    Windows Vista

    Using the F8 method:

    1. Restart your computer.
    2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
    3. Select the Safe Mode with networking with the arrow keys.
    4. Then press enter on your keyboard to start mode without failure of Vista.
    5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
    6. Do whatever tasks you need and when you are done, reboot to return to normal mode.
  • SATA version?

    Does anyone know if the following is SATA 2.0 or 3.0?

    HPE-500f

    N Alvorix-RS880-formfat (Alvorix) motherboard

    Thank you

    jp5150 wrote:

    I even tried the manufacturer's website and nobody says what version of the SATA it it. That suggests to me 2.0, but I don't like to assume.

    Hello

    All providers, not only HP, when they are nothing new, they shout louder and put it on their products. When they don't yell, you know what I mean.

    Kind regards

Maybe you are looking for

  • Replace sata11 by low-voltage ssd elitebook 2540p 17 2.13

    Hi all... I have a couple of HP EliteBook 2540p with I-7, 2.18 GHz, 4.00 GB, 1.8 "320 SATA11 supported small volts system that takes only a HD SATA11 1.8 (unless I have remove the dvd) and want to upgrade to 120 GB (or more) SSD... You know what I'm

  • Windows 8 reset hard drive

    I recently had to "reset" my hard drive.  This is the option that deletes files carefully and recharge to the os and software that was purchased with the system, not the quick erase of files and reload option.  This seems to have been especially succ

  • QML QVariantList QString Converter?

    Hey all I'm relatively new to programming of BB. I have some experience in Android and Windows Phone, but I think that BB10 will kick a lof of * beep *! I did a bit of programming for my application and I use a Web service to download the json from t

  • Smartphones Blackberry blackBerry server not connected

    My blackberry server does not work - outside of WIFI areas, I don't get emails and none of my apps don't work, however my internet still works? My phone is like that for a few weeks now - I tried to call my mobile service, who put me through a blackb

  • ACS 5.2 selection policy/access service attribute question

    Hello I use ACS 5.2.0.26 and formed the selection air Service to authenticate the PEAP wireless clients based on the suffix of the domain that is used by clients. If I use the IETF-RADIUS-RADIUS attribute: User name to do this, am I right to say that