Very limited wireless connection

I have a HP Pavilion dv7 - 3153ca with a 64-bit windows system 7 and I'm only able to get a wireless connection when the laptop is very close to the modem. Once the laptop is moved, for example, to another floor of the House, the connection is lost and cannot be re established until I have the back next to the modem. He has no problem with the wired connection. This has happened while he was trying to pass my McAfee security provider, although I don't think this is the problem that my other laptop (a Dell) converted without this problem. The other laptop continues to maintain its connection Wireless throughout the House, so the router and the modem is not the issue. I downloaded and re-installed the adapter without modification. I have scanned the laptop and nothing is reported in the mess. Are there any ideas as to why the wireless connection works only when the laptop remains close to the modem? Thank you.

It seems I may not have been very clear in my previous post.  I wanted to suggest was to reverse the connection of the antenna.  As mentioned in the thread I linked, the connections might have been reversed from what they should be from the factory.  If this is the case, then connect the antennas in a factory setting would not solve the problem.

Have you tried to reverse the antennas?  If they are in the deformities, then this would fix it.  If they are in the right position, then the worst you would have (only in the deformities) would drop signal strength.

Tags: Notebooks

Similar Questions

  • EA3500 very slow wireless connection

    When I test my connection speed wireless with Linksys EA3500 get one only 5 Mbps download speed, if I connect my computer directly to the modem from my ISP I get a speed of 30Mpbs, someone has an idea why such a huge difference or have ideas I can speed thing on my wireless connection, no problem of co-location the wireless device which is 5 ft of the computer and only one switched printer connection Othere to my network wireless off?

    Maybe it is better because it can become very complicated when troubleshooting these issues

  • Very slow wireless connection

    Hello

    I am owner of the Dell Studio 1555 and I Dell Wireless 1397 WLAN Mini Card on my Board. There is a problem when I am connected to my router and Internet runs very slowly. The signal strength is excellent, I use WPA2 encryption. There is no problem to connect to the network, I had just to configure the ipv4 as IP, the door parameters and so on because the automatic setting didn't work. So I run my firefox and google charges pretty okey but slow. It is then impossible to surf because the download speed is something like 1 kb/s. When I plug in the ethernet cable so it's all good. I tried reinstalling the drivers but nothing has changed. I use windows vista. I also tried connection in linux ubuntu system, but same problem occurs. My friend uses a wireless connection of the router same and everything is going well for him. How to speed up the connection?

    Best wishes

    Simon

    If you connect the laptop to the router (or the modem) with a cable? If it gives a high speed, you may need to change the channel is using your router. It's probably 11. Replace 1 or 5. Can significantly reduce the interference from other wireless devices connect speeds.

  • Laptop has limited wireless connectivity.

    Computer connection laptop wireless router problem

    We have changed our router to a BT Voyager 2091 wireless a new travel of BT of 2091 on our pc.  We have a full internet access on our pc but when our daughter trying to connect with his cell phone, his laptop computer is to find the router and when it enters the key wireless laptop connects to the router with a limited access that does not connect to internet.  How it is access to the internet through our wireless router? Answers would be appreciated.
    Thanks Julip

    .

    This happen to changes in the security mode of the wireless access point

    remove any preconfigured laptop access point

    and or change the access point laptop preconfigured according to the Muse of fashion security router

    for example. security password, type of security, WEP, WPA, WPA2, PSK, TKIP etc.

    Concerning

    Hope this will do the nedfull

  • WRT160N Wireless connectivity limited or not

    Hello. I have a WRT160N router set up on a XP computer with DSL service. Have a Realtek to connect to the network local and Marvell Yukon for the wireless, which presents itself as the connection to the local network 5 in network connections. The Realtek works well but the Marvell Yukon shows "limited or no connectivity" and cannot renew the IP address. Tried to manually key in one IP address, but it runs very slowly (584 sent, received 4) and Network Magic also does not detect connections wireless at all.

    Y does it have wireless connection can get a speed much better with the IP address or are there other parameters that need to be adjusted for this? Is it possible to have two connections working or should be just one or the other?

    Hello. Yes, the OS is Win XP Pro. For some reason, the wireless network connection properties has a second tab for wireless network. The second tab there arises as advanced.

    What finally solved it for me has been assigned an ip address that has worked. Both cards work fine at the same time without any conflict so far. Only using one of them at this point, but it is good to know that the other is works when necessary.

    Thanks for your help, if. Really appreciate it.

  • limited access - connection Wireless error

    Computer my son has worked well, but with some difficulty getting enough 'strong' connection for several months.

    Then, suddenly, we get an error 'Limited access' on the wireless connection. We have experienced countless challenges, including the suggestions here: http://answers.microsoft.com/en-us/windows/forum/windows_7-networking/windows-7-occasionally-drops-the-wireless/e834b67f-12ae-4b3c-aa13-af27553350bd?auth=1 but without success.

    Is a strange, because it shows that it has a connection, when I use the ping, I can see that 25% of the packages they do and from the wireless router (Yes, I recognize that 100% should make the trip), and we can not explain behavior, I can put my laptop in the same place and write this extended ad. We can look at the network and sharing Center and see the network come and go from this computer.

    In addition, we tried to update the driver (he says he has the most recent version) and have resorted to here for assistance.

    We've been on Windows 7 all the time, and he claims that it has not installed any new application (the download and installation of privileges are limited), so I don't think that it is the source of the problem.

    If anyone can say, we would be grateful for help.

    Ok

    did a system restore full of a checkpoint 5 days ago and was able to get the system.

    Thanks for this feature. Explanation is still a mystery.

  • Wireless connection is always set to "limited connectivity" on Windows 8

    My wired connection works fine, but when I try to connect wirelessly, my connection is limited. This problem is not moved when I got to my laptop. I have tried to start in safe mode, install the latest drivers for my wireless card and also get into the command line "netsh". Any help would be appreciated, thanks.

    Please try the below given the stage he worked for me for connection problem in Windows 8 Pro limited. I tried to connect via Nokia Lumia 720:

    1. Right click on your WIRELESS connection and click view connection properties.
    2. Click the Security tab.
    3. Click on Advanced settings which opens the 802.11 settings.
    4. Check compliance to enable FIPS Federal Information Processing Standards () for this network.
    5. Click the OK button.
    6. Reconnect your computer by WIFI and enjoy the internet.

    Please update if it works for you.

  • WRT54GL: Fast cable internet connection; very slow wireless

    I have been chasing a problem for months and I am at the end of my mind.

    I started with a cable modem Motorola SB5101 and Buffalo bison wrt-hp-g54.  For years, we had a (intermittent) desperately slow wireless connectivity.  Recently I started to run through Speakeasy.NET speed tests to try to find a motive.

    Wire speed is consistently running 15-16 Mbit/s, compatible with the speed promised our cable package.

    Wireless speeds were a different matter.  From multiple computers, they would sometimes as soon as the wire speed; then all of a sudden (from all wireless computers) the speed would fall to 0.5 Mbit/s or less, then the speed measured on our single wired computer remained at 15 Mbps.

    Restart the router would mitigate the problem for a while, and then the wireless would fall up to 0.5 Mbps.

    Wire speed would remain stable at the nominal 15 Mbit/s.

    Well, looked like a bad router.  I replaced it with a WRT54GL hardware version 1.1.  I've updated the firmware to the last - v4.30.16.

    I selected a channel (2) wireless network what inSSIDer 3 watch is not used by any neighboring router (i.e., no interference).  I have that checked regularly and am sure that interference is not the problem.  The router is configured for the wireless G only; WPA - AES.

    The same problem occurs with the new Linksys router.

    In desperation I replaced the old modem SB5101 with a new SB6141 cable, not believing there could be everything possible that could help but, this what the devil - we will eliminate it as a factor as possible and go to DOCSIS 2.0 to DOCSIS 3.0.

    The problem persists.

    Thus, new router, cable modem brand new, constant wire-speed, without strong signals wireless, channel interference all around. but the problem persists. There has been no improvement on the old hardware I used.

    All computers, but a (XP Pro) is running Windows 7 Pro.

    The problem is not predictable, except that the speed degradation will happen sooner or later - and this is not progressive.  Suddenly, he fell like a stone and sticks to 0.4 to 0.5 Mbits/sec.  Reboot the router (usually) will fix it for a while, and sometimes it will clear up on its own, given enough time.

    I ran inSSIDer several times while this is happening, but he sees no other no signal on the channel I use--in fact, none on adjacent channels either.

    I checked from wireless to the router table and there is no other than our device, so it does not appear that the network has been hacked.

    Does anyone have an idea what might be going on or suggest an action plan?

    The only thing I can think is that there is something between the router and the computers wireless in the House which is eating up 95% of the bandwidth wireless - a sort of voting out of control.  But what?  I'm completely stuck.

    Follow-up.  I changed the channel 1 wireless; After doing some research I realized that sharing a channel (as long as your signal is at least 20 dB louder) causes fewer conflicts overlapping channels.  I have not changed anything else.  I'm tempted to allow the break-up of the frame but implementation of that seems to be somewhat specific to the supplier so I'll let it be.  In any event the wireless speed now as fast as the wire speed.

    The result is that since the re - install the Linksys firmware and do a hard reset that I saw not a single instance of the speed problem.  So I still don't know exactly what caused in the first place, but I'm glad that the problem has disappeared, so I'll just let things be.

    Thank you!

  • WRT54G - wireless connection limits?

    Yes, I have a WRT54G V6 router, and I wonder how many wireless connections it supports?  Because, I have a wired connection, and whenever I try to connect more than 4 wireless devices, a device will be get launched.

    So is there a way to open more wireless connections or suggestions?

    Thank you.

    On the computers of all Vista and Win 7 disable IPv6 in LAN properties for both wireless and Wired Adapters.  Disable UPnP in router.  Restart the computer and try again to connect.

  • U940 PSU6VA satellite - wireless connectivity problems

    _ * My specifications: * _
    * Model: * Toshiba Ultrabook (Satellite PSU6VA - 00S 002 U940)
    * Operating system: * Windows 8.1 x 64 (upgrade of Windows 8 x 64)
    * Wireless adapter: * Intel Centrino Wireless - N 2200
    * Wireless adapter driver version: * 15.10.0.12 (which is the last for my device)

    I got this Ultrabook since February 2013, and throughout this period, I always had problems with wireless connectivity, even after a factory reset. My wireless icon varies between three States:
    * Internet access
    * Limited (in which case I can't connect to the internet or any other device on the network)
    * Not connected - connections are available (and if I try to connect to the network, it will fail)

    Sometimes my computer would instantly reach the State of "Internet access" at startup and remain in this State. Other times, it would be 'limited' for several minutes after the start of my computer before it finally connected, and even in this case, the connection will drop out every now and then. In the worst case, it would indefinitely remain "Limited" or "not connected", regardless of how many times I reset my adapter wireless or rebooted my computer.

    Until very recently, I always thought that these problems have occurred randomly. However, I noticed recently that I have always a connection perfect, whenever there is no other computers connected wirelessly to my router, and I always have problems more or less when there is at least another computer (or even a smart phone) connected wireless to the router. If there is another computer connected to the router via an Ethernet cable, this causes no problems. It's only wireless connections that interfere with my computer.

    It is only this computer that has these problems; the other computers in my house ever experience these issues, no matter how many computers is online. In addition, my computer is not only these problems with my home router; It has the same problems on the network wireless at my University.

    My question is, how do I fix? Is this a known bug or is my defective wireless adapter? I know that I can connect using an Ethernet cable if possible (I have never problems with Ethernet connections), but this is not always possible at the University.

    Did you remove the old driver Win 8 Intel of the system before you upgrade to version 8.1 to win?
    The old Wlan Intel driver could affect the performance of a Wi - Fi connection.

    The driver update page Win 8.1 says clearly that Intel Wlan driver must be uninstalled and the
    Inbox Windows 8.1 version must be used.
    http://support.Toshiba-tie.co.jp/windows81/drivers/PSU6V_Up_au.htm

  • On Satellite L750/0 wireless connectivity issues s 5

    I own a laptop L750/0 s 5.

    I seem to have a problem with my wireless connection, where anywhere not at 10 m from the router the connection cuts in and out with the yellow sign 'limited connectivity' always appears. disconnect and reconnect solves the problem for a few minutes. Ive resorted to the close session of the router.

    the computer is 2 months old, the Wlan driver is up-to-date. power options have been configured to be on maximum performance for Wlan etc etc.

    The main thing that annoys me, it's all the others (much older laptops) in our House very much work where mine doesn't. I actually lost performance from where I can get my old toshiba portege m300 to this new wireless signals.

    In terms of information, the computer is running windows 7. Wireless network card is Atheros AR9002WB-1NG.

    If theres any other information that you need, as im sure there will be, I would like to know and ill try my best.

    The router is really new.

    Thanks for your help

    > the computer is 2 months old, the Wlan driver is up-to-date. power options have been configured to be on maximum performance for Wlan etc etc.

    The latest Wlan drivers can be found here:
    http://APS2.toshiba-tro.de/WLAN/?page=downloads

    Please keep in mind that you use the latest driver v9.2.0.419.0

    To be honest, I had the same idea to disable the power save for Wlan and it more often it should work are you sure that you have changed this in the same power station that is used when the laptop is running on battery power?

    However, it would be interesting to know if the Satellite L750 uses the same Wlan 802.11 standard, as do other portable
    In the Device Manager-> properties-> Advanced tab Wlan card, you can choose the standard Wlan 802.11
    Recommend to check this

  • Problems with the windows computer 8 loss of wireless connection?

    I'm on my 2nd NEW Dell with Windows 8 in the last 3 weeks. I use a Trendnet Wireless router to connect to the internet. The 1 Dell computer dropped the signal wireless on the 2nd day I got it. The 2nd Dell computer began the wireless signal very frequently the 5th day I got it. My Dell Inspiron 1545 computer that is 3 years old, 1 year 6 months never old old ipod and iphone removes the wireless signal. Help, please!  I've been in contact with Dell several times with any resolution of this problem,

    I'm on my 2nd NEW Dell with Windows 8 in the last 3 weeks. I use a Trendnet Wireless router to connect to the internet. The 1 Dell computer dropped the signal wireless on the 2nd day I got it. The 2nd Dell computer began the wireless signal very frequently the 5th day I got it. My Dell Inspiron 1545 computer that is 3 years old, 1 year 6 months never old old ipod and iphone removes the wireless signal. Help, please!  I've been in contact with Dell several times with any resolution of this problem,

    I have a new laptop from Toshiba with WIN 8 pre-installed, and I have the same problem.  I ran the program of problem determination and it reset the WiFi card and fixed an issue reported.  He canned breed, I have 2 WIN 7 laptops who have no problem at all.

    Symptom: In normal operation, the wireless connection to the router drops to limited connection (No. Internet).  It does not actually lose the router, he loses just an internet connection.

    Update - has visited the Intel site to check the drivers.  They had an updated driver, even if the driver search said I was current.  I updated the driver and 24 hours later I got not drops.  I hope that fixed it for me.   http://www.Intel.com/p/en_US/support/detect/wireless

  • Bluetooth wireless connection

    MacBookPro OSX El Capitan; Version 10.11. Retina display - MacBookPro connects to the printer HP C6150 help electrician with no problems. not then attempt to use the bluetooth connection.

    To a printer wireless connection works using old MacBook. Bluetooth connects to the mouse and works very well.

    Select the Bluetooth device-

    The computer icon shows - not connected

    Apple mouse - connected

    Hello analyst.1,

    Thank you for using communities of Apple Support.

    I understand that you can print from your MacBook Pro to your HP using Ethernet and wireless printer, but not via Bluetooth. I know how it is important to ensure that you can connect to your printer via Bluetooth. I'll be more than happy to help you with this.

    Use OS X El Capitan: Add or remove a printerand make sure you have the latest version of the software installed and printer connection instructions, specifically, this section:

    Add a Bluetooth printer

    1. Update your software: choose the Apple menu > App Store, click updates, and then install the listed software updates. Even if no updates appear, this ensures that OS X has the latest information on printing software you can download from Apple. If you don't do this, you see a message that software is not available when you connect your printer.

      If you have a printer AirPrint, you have no need to check the software updates.

    2. Prepare your printer: use the instructions that came with your printer to unpack the printer, install the ink or toner and add paper. Turn on the printer and make sure it is not the display of errors.

    3. Connect your printer: follow the instructions that came with your printer to make sure it is ready to connect through Bluetooth. You must also make sure to activate Bluetooth and set up the printer Bluetooth as a new device.

    After connecting your printer, if you see a message prompting you to download new software, be sure to download and install it. OS X will automatically use AirPrint if your printer supports.

    Have a great day!

  • How to configure a printer wireless connected to Time Capsule?

    I just bought a printer HP Color LaserJet Enterprise M577z MFP Flow. It has capabilities of wireless printing. So far, I was able to connect wirelessly to one of my MacBook Pro computers, but only by having the printer create an Ad - hoc network that allows up to 5 devices to connect to the printer. But that of not what I want because every computer should manually disconnect the Wi - Fi network, connect to the Ad hoc network, the print job and then reconnect to the Wi - Fi network whenever a print job is required. It is very difficult and frustrating.

    What I would like is striking is the printer act like a network printer by wireless connection to my Time Capsule. I can't connect the printer to the USB port of time Capsule because they are far away from each other, and I don't want to use cables throughout my place. But I have no idea on how to do it because I can't find this option in the menu of the writer or configuration of the United Nations the HP utility software.

    I hope someone here could help me, please. Thank you!

    I have an Epson printer, so some of my experiences may or may not apply.

    I also have a time Capsule, and my printer and Time Capsule are far apart.

    My current configuration looks exactly what you are looking for: a wireless network provided by Time Capsule than all my Apple devices to a wireless connection, and my printer connects to the same wireless network.

    When I first bought the Epson printer, I needed to connect it to the Capsule of time via a USB port.  This sounds as if it were true for you as well.  So, for this very short period. I moved the printer via the USB port next to the printer, the connected Time Capsule, made the setup and then the printer recognized my standard wireless network.  I've returned to steady state, which I use now, with the printer and the far (actually on different floors) Time Capsule.

  • 7520 HP loses the wireless connection. What can I do?

    I've seen lots of talk about HP products, loss of wireless connection.  I have the same problem with my 7520.  Initial Setup is perfect, but he began to lose the connection when it went into standby mode.  Someone at - it a solution?

    THERE IS A FAST SOLUTION!
    On April 18, 2014 (page 11 of this thread), I posted a quick solution. My HP7520 printer has worked on Netgear router WIFI 7550 flawless since then. I suggest you read this post.
    From long experience with HP, I found they have great hardware, but their software has always been dismal. The ultimate "fix" would be for HP address their failure of a software that allows to my difficulty in working.
    A single "tweak" in the router security settings wifi will do. The rest of settings changes other people have suggested are short lived (about an hour in most cases), while they don't be reconnected unless they restart everything. It makes sense because of what is happening.
    The single "twist" parameter should logically point HP programmers to where in the firmware, there is the problem. They listen to? And, really, it doesn't matter on all other settings printer and router. All mine are back to the default settings and it all still works very well.
    Go to a BBQ and stop wasting your time on this issue.
    Ken

Maybe you are looking for

  • HP 110-243wb desktop PC: can I upgrade the ram and memory of my HP 110-243wb desktop PC?

    Can I upgrade the ram and memory of this HP 110-243wb desktop PC? What suggest you and you thank in advance.

  • HP SPECTRUM 14-3210nr drivers for Windows 7 Downgrade

    Hello, I have a HP SPECTRUM 14-3210nr Ultrabook I went down of Windows 8 for Windows 7 because I had to work. Unfortunately, I lost a number of drivers in the process and cannot connect to my wireless network. How can I get the drivers?  The model nu

  • XP boot screen does not open

    people from g ' Day!  I had a pc blackout was in sleep mode, now it used open in xp installation sreen leds of loading begins to run as usual, but stops with a led remains always turned on? then go back bios post message (like a dog chasing its tail!

  • bug in the drop-down list

    I want to retrieve a value that I select my drop-down list. When I run my plants of code with the debugger to step to retrieve the index of the selected item. Please help if you are looking for a problem public class Day extends MainScreen { public O

  • Need to Smartphones blackBerry Desktop Manager Software

    I need Desktop Manager for Blackberry Storm 2 software.  Could someone help me please.  I bought a used Blackberry and do not have the CD. Thank you Jerri