VI is jump a loop "For".

Zipped VI is fixed, the upper level has "7_AD-DC producer consumer" as the title.  You will have to dig into the folder for access.

I have attached a picture of the Vi, highlighted in red is the loop in question.

The problem I have is that when I run the vi has the range of 0.25 to 0.5 Volt (chosen in the loop of producer not shown), it works fine, but if I run the vi put on the beach of 1 volt, it ignores all highlight loop, and finishes just the event.

The program aims to help the particular device calibration.  If you follow the path of the error, it crosses the upper part (1605, 1605 mode range, range of AC - DC, the factor N, etc.) all the way through the indicators for "1 k reference in ' and ' 1 k reference on.  The program runs right up through these measures of reference, but when it is in range Volt 1 (shown in the picture) it ignores the entire for loop.  I son of error in all, and I thought that those who would prevent race conditions and they would oblige the Vi to run as expected, but apparently not.

It's kinda a Vi spaghetti, I'm not the best with LabView, but it seems so strange to me that it works when the value 1/2 a volt but don't not 1 volt value.  I put the indicators on the elements that fuel the loop For, the number of frequencies and the tables of frequencies look good and I can't really think what causes violence to ignore the loop for.

The for loop is not in 'jumps' it of executing 0 times and out of default data for all tunnels.

You have an entrance tunnel auto-indexé why wire terminal N at all? The loop will be the least number of iterations it can.  N times, either the smaller auto-indexd table is something less.

EVEN worse: the indexed table auto comes from a tunnel exit case structure value "Use default if unwired" so you have two options.  There is a hidden code clear the Board before being sent out of the cases showed, OR the value of the number of frequencies is<>

Tags: NI Software

Similar Questions

  • jump on a for loop

    Hi guys,.

    I have the impression that this is a stupid problem and know the solution if probably obvious, but I can't seem to find it

    I have a loop with several inputs and outputs in a Subvi.  When the Subvi is run all entries are read, the loop is skipped, and the outputs are sent.  Does anyone have any idea why the for loop is ignored?  Everything seems to be wired corretly?...

    The vi is attached.

    Thank you!
    Christopher

    I can't open your code due to my having LabVIEW 2009, but here's one thing to check: do you have automatic indexing on at all?  Perhaps, he does not run the expected amount of time due to a table being wired like 'auto-index' to your loop for?

    Another thing to check is try to place an indicator on the output of the variables 'N' and 'i' of the loop (letters of blue boxes that appear automatically).  That should tell you the "N" land of shadow of time it will perform an iteration and the value of the current 'i' reiteration.

    When you use the execution to highlight, you see it execute the code inside the loop?  If so, how many times?  And how did you expect?

  • How will I know if new loops for 10.1.1 has uploaded?

    So I downloaded the new update, but I can't say the old the new loops loops.  Download it and install it or I have to click on the option 'Download the sounds available' in the menu?

    OR

    Can someone give me the name of loop for one of the loops again so I can search my library of loop?  Thank you!

    It is no new loops have been installed for me, but they may have been installed earlier by the logic. Maybe the update adds iOS GarageBand loops, take a look at this list.

    How to get iOS GB loops in GarageBand for Mac.

  • New loops for 10.1.1 even as new loops of logic?

    I have all the additional content for Logic Pro and with the exception of the fabric of Alchemy, are the new Apple Loops for Garageband 10.1.1 identical to what I already under Logic Pro?

    GarageBand gives me the option to download the entire library, which I don't want I don't have to.

    I suspect these new loops for GarageBand 10.1.1 are already in my folders of loops when I updated Logic Pro a few months ago?

    Thank you

    Robert

    T

    The App Store shows the update like this:

    2600 new Apple Loops and sounds.

    I also installed Logic Pro X.

    There is no new loops installed after 10.11.1 GarageBand update.   The last loop in Library/Audio/Apple Loops is 80 return Beat.caf frommay 2015

    GarageBand must have installed something, because the absence of plug-ins error messages are gone, when I open iOS projects GarageBand, but I can't find any new items in the folder/library.

    I'm now trying to download all the available sounds. We'll see what happens.

  • If I use a single individual loop for my video and upload it to youtube will be my video will be blocked or will I get copy right strike?

    If I use a single individual loop for my video and upload it to youtube will be my video will be blocked or will I get copy right strike?

    I already read the agreements loops but unable to understand exactly what it means please help me...

    They say individual loops must not be commercialy or other wise distributed...

    That means individual loop should not be used?

    Is the only thing you can NOT do: "Yes, I did these loops and now I'm selling you these loops, claiming that I just them

    So they are free, but you are not allowed to sell unaltered loops claiming that make them you. So you can use them for any kind of music, published published, obscure, commercial, anything; without additional costs or restrictions.

    Hello... Please help me I want to just use a single loop of logic pro X for my video and want to download YouTube wil...

  • Clear out in a loop for

    Hi guys,.

    I have a problem, so I activate timed values on the outputs analog of my RedLab card.

    The problem is that when I stop the program, the outputs are always activate.

    How can I solve this problem?

    Best regards from max

    What version of LabVIEW?

    I forgot which version he presented, but lately, you can add a CONDITIONAL TERMINAL to a loop FOR.

    Use it to stop the loop if the user clicks a button or if the voltage exceeds 3.14159 Volts, or whatever.

    You can also use a basic while loop, set the AUTOMATIC indexing entries and compare yourself 'i' to N - 1, in the loop.

    Stop BUTTON so STOP = TRUE or i = 3.14159 > N-1 or V...

  • Creating a table of automatic indexing of loop for

    Hello and greetings from a newbie to LabView,

    In my program, I want to write several orders via VISA and read them in order. I created a table of command and auto-indexé to a loop for.

    I want to receive a table of responses, in the order they were read of course. However, I'm not sure what is the best way to do it.

    I'm sure that the solution is simple but have been unable to find one. I have attached the vi for reference. (VISA vi reading is part of the LabView unit driver), which works, but looks like a unmodular approach and inelegant.

    Thank you!

    Simple, you can auto-index the output!

  • Create a table in a loop 'for' (reset the number of loops)

    Hello

    I try to incorporate a signal of acceleration from an analog input CRIO to get speed and then further integrate to get the moving of a vibration system.

    I understand that to achieve integration, a table must be fed in. My problem is that I could not buffer the signal in a buffer block, as I couldn't find buffer blocks. so I decided to create my data table by using a loop "for". The nests of the loop 'for' inside a timed loop. The problem that I'm stuck on is how to reset the loop 'for' in order to fill the buffer with each iteration of the outer loop timed.

    I enclose the code if that helps. Note that I use labview in 2013.

    If anyone who has encountered a similar problem before can help me, I would be gratefull.

    Concerning

    Ali

    You can use a shift register initialized as inputs to your curls, to build your table of one. However, you realize, don't you, that the execution of your program as written loops as soon as the computer can spit out responses, then the output array may contain several points that took place before the entry has updated? Assuming that your thing cRIO (I've not worked with these) has integrated into its routine acquisition of calendar data, I suggest you put that inside the loop to get a data point by reading.

    And do you really want your graph to distance for update only every thousand points (points of acceleration million) speed?

    Cameron

  • VI re - enter several times a loop for

    HW can I call a same vi... (reentrent vi several times a loop for). using reference function call.

    Thanks in advance

    Bilel

    Use x 8 for reference VI options open to call dynamically live reentrant

    For more information read the help of LabVIEW for this nodes!

    Christian

  • How to select the first item in an array in a loop FOR

    Hello.

    I use Labview 8.5

    In my application, I have a loop 'for' where I read some values from a device. (strings and digital)

    As you know Labview 'stores' values up to what the loop 'for' is completed, and then they come out in a table.

    Ok.

    I want to just use the first element for strings and digital and then do something with it, like to compare (for digital)

    For strings, I used successfully 'Split 1 D Array' and choose 'everything first subarray'. Good.

    Now for digital that works too, but the result is an element, array type too. I need to be digital (decimal) is not no table type, because I need to compare (greater than 0). Then use a case...

    So, table of an element in a digital decimal? Or the table at the first decimal element. How?

    I tried also with the subset of the table. Even think. Labview won't let me compare a table 1 d with 0. It makes sense, but how to convert, to have the first decimal element?

    Try to use the 'Index Array' function. If you do not connect to the terminal of the index value, it will return the first elelemnt in the table. If wire you an index, it will return the value specified.

    Ben

  • back to zero 'loop' for Interior "Subvi.

    Hi guys,.

    Silly question perhaps extreme but fast. I have a fairly large VI with several of the Subvi. Inside of these sub - VI, there are some for loops that do not seem to whenever the Subvi is called. While making the analysis of the data, it basically accumulates the data of the previous file as well. For example:

    folder a. gives 4 results of loop for the Subvi

    file B gives 5 results of loop for the Subvi

    Not appear in the final as having 9-results and not the 5 that I expect.

    I've been playing with deletion of points of interest, but I was wondering if there was an easier option?

    your

    Patrick

    Initialize works the cordoning off of the node as a first call, and since it is always in memory it is reset only once.

    (correct me if I'm wrong)

    /Y

  • Problem with loop "for".

    Hi all

    How can I solve this problem

    Disable indexing on the right side of the loop for.

    Consider using shift registers.

  • Automatic indexation 2D array in the loop For - what is happening?

    I found many sources dealing 1 d tables in a loop For or a While loop, using automatic indexing, but nothing on the tables of higher order.

    I work with a program that feeds a 2D array in a loop (see table).  From what I see, it looks like this the results of automatic indexing in a 1 d, the first column of table 2-D table.

    This is the expected behavior, and it would hold true for arrays of higher order, table 3D for example?

    Is it possible to refer to the second column rather than the first?

    wildcatherder wrote:

    I found many sources dealing 1 d tables in a loop For or a While loop, using automatic indexing, but nothing on the tables of higher order.

    I work with a program that feeds a 2D array in a loop (see table).  From what I see, it looks like this the results of automatic indexing in a 1 d, the first column of table 2-D table.

    N ° it auto-index through a line at a time table.  You will get a 1 d table which consists of all of the columns that make up each row in each iteration.

    This is the expected behavior, and it would hold true for arrays of higher order, table 3D for example?

    Yes.  Automatic indexing on a 3D Board will give you a table on each iteration of each page 2D.

    Is it possible to refer to the second column rather than the first?  This question applies once you understand the first response.

  • Output graphics of two loops for

    I would like to see a graph of the output generated in both loops for.

    X: steps (i x I have two loops)

    Y: Y1 should graph the polar output

    Y2 should chart the Azimuthal output

    Probably very simple to resolve/upgrade in place.  (The output file works fine).

    Thank you

    Kevin

    Good work Kevin.

    I have some suggestions for you (I don't know what it will be eventually, because then maybe they're based):

    • If the data do not change over time, you can use a graphic instead of a graph; Whatever it is, reduce the necessary processing power by updating the two parcels only once for a full run of the outside loop (see below)
    • You have a lot of indicators that are not obviously necessary (they simply out what puts out control - off 4;) Stop 5; Polar; Azimuthal, etc.).  When you submit here, the code is more it is easy to understand and faster you get an answer (minimal document also helps understand us what all is for).
    • Use the decrement vi but don't take it off 1 (reduced the increase in code).
    • Avoid strain - explicitly cast I32 to double so that no appeal should be made to the Manager of memory running (will reduce your footprint of memory of codes).
    • Written file are intensive and bays of building CU generally allocate dynamically memory - try to avoid these as much as possible.  In your VI, you can write to the file once when all iterations are complete.  This will reduce the runtime of the VI.

    Anyway, there are a whole bunch of thoughts that you probably care to hear, but I hope they have been helpful.

    Cheers, Matt

  • How to get the items on a loop at the same time during the execution of the loop for

    Hello

    I am a student. I would like to know how to get the outside loop counter values For in parallel so that the loop runs rather than obtaining the value finally outside the loop for future prospects for the answers.

    Thank you

    Frederick

    You already said yes, and you have said some of the different ways (registrants, locals, reference, queue, etc.). Since the information was provided to your request, the thread can be considered closed? If you want details about how to implement something, you must provide the details on what you are doing.

Maybe you are looking for