Virtual COM port do not get detected using labVIEW Installer


Sorry for the thread...

The windows device manager sees a USB port.

The manufacturer's website indicates that for windows XP it didn't need a driver, windows use its own driver.

I try older driver from the manufacturer, but I have the same result: the windows device manager sees a USB port.

1. yes I have tried but it still sees a USB port.

2. drivers from the manufacturer has not solved the problem.

3. I will ask to help the manufacturer.

Thank you for your help Ravens Fan,

Concerning

Tags: NI Software

Similar Questions

  • How do troubleshoot you a USB virtual COM port?

    Object

    Send orders of Labview to an Arduino board using the Advanced Serial write and Read.VI.

    The problem is that no orders are received by the Arduino.

    However, I can use the Serial Monitor built into the Arduino IDE to send commands to the Arduino and get the required result.

    I checked baud rate, the designation of COM port and the command is a simple as string 600,0.  The VI shows no error message.

    So, I'm looking for suggestions on how to troubleshoot a USB virtual COM port.

    Howard


  • How to create a Virtual Com Port in Windows 7 for Palm HotSync

    I've just updated wo Windows 7 Pro 64 bit.  Because Palm does not support USB synchronization under a 64-bit system, it tells me that I need to create a virtual com port for my bluetooth device to synchronize.  I can't understand how to create this port under Windows 7.

    Hi Sonmox,

    Welcome to the Microsoft Answers site!

    In the Sub in view of the link you need to download the Palm Desktop and HotSync Manager. This software allows you to synchronize your device Palm with your computer, for your info is backed up and easily editable on your computer.

    Visit the following is given link of Palm and configure your Bluetooth device.

    http://KB.Palm.com/wps/portal/KB/common/article/49229_en.html

    When you set up your Palm device to synchronize using Bluetooth technology, you create a 'Bluetooth partnership' between your devices your computer (also known as "pair" or "trusted device"). This allows you to synchronize your device wireless and your computer have to authenticate each other, every time that you synchronize.

    Follow the steps in the document to sync your Bluetooth device.

    Hope this information is useful.

    Amrita M

    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • break in series on the com port does not work

    Hello everyone:

    I have the following problem:

    I am writing a command via the ' 'entry visa' vi on my pc com port. in some cases the com port do not return anything. This means that my "visa read" vi would timeout. the problem is that, later, I need to send more orders but must break the line in order to be able to do. I inserted the "breach of visa" vi but didn't have the reaction I was expecting. the line does not break. I tried to increase the duration of the break, but that does not work either.

    Any ideas?

    By using LabVIEW 2013

    A break will not break the connection, it will just a 1 to the Tx line for a period longer than 11 baud (?) or specified length.

    A hardware check that the breakdown is send: connect a scope or a DMM TX and GND, a 500ms break must be clearly visible even on a "slow" DMM (k resistance 10 and two LED antiparrallel or RS232 minitester practice would do the same job )

  • How can I create a USB Virtual COM Port

    Windows XP Professional / SP3 / 2002 Version

    How do I create a virtual COM Port to USB, so I can run software applications of a Bus USB flash Drive?
    The reason why I am eager to do it, is because I use an audio sequencer and it requires 1 GB of free disk space and at least 1 GB of RAM is recommended. My machine has 0.5 GB of RAM and a total of 6.55 GB of FREE space. My machine has a 256 MB RAM module and I bought another 256 MB RAM module. The manufacturer said that 512 MB of RAM is the maximum that can have my camera.
    My goal is to buy a 4 GB Flash drive and use it to add RAM on my machine. I am also wanting to be able to run software applications that are installed in the USB Flash drive.
    My basic goal is to install the DAW in the USB Flash drive and work with the program that is in the USB Flash drive, and I hope that will release of enough memory on my laptop.

    Hello

    Unfortunately, you cannot use a USB flash as a substitute for the RAM drive.

    Similar topics as an example with the info:

    http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-hardware/can-i-use-a-USB-flash-drive/70cf81fa-D113-4485-8305-c030665eeac0

    http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-hardware/can-a-USB-flash-drive-be-used-as-an-external-RAM/d711a70e-6878-4552-933C-423fa04fb222

  • series PCI and ocy port driver easy serial port can not get driver Windows 7 Professional

    series PCI and ocy port driver easy serial port can not get driver Windows 7 Professional

    Hi Louis,.

    What is the brand and model of your computer?

    You can visit the computer manufacturer and try to install the latest version of the Chipset drivers.

    Also try to use Windows Update to update the drivers and check if it helps.

    Automatically get recommended drivers and updates for your hardware

    You can also get in contact with the support of computer manufacturer for assistance.

    Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.

  • COM port do not appear in my application

    Hello

    There is a reason why the com ports are not visible on a Xp Embedded Touch Panel?

    I have to connect via a serial port in my application, but the com ports do not appear in the control of Visa Resource Name...

    I've included any VISA in additional Installer related things...

    OK I solved it!

    I copied manually install runtime National Instruments visa drivers DVD and installed on the touch and now the com ports are found!

  • Virtual Com ports never get reused after UN-installing of software that use

    I have install and uninstall the bluetooth drivers (Microsoft, broadcom and bluesoliel) in order to obtain different devices to work. When I started this exercise, used by bluetooth comm ports were low numbers (com 4 and 5 for example). If I uninstall the bluetooth drivers, then reinstall the or some other driver, the com port numbers used become com 6 and com 7).  Old ports com can never get reused and there seems to be any place where I can find them (and I hope that free them from their State of limbo).

    Now that I've got things nearby work properly, I get to com 25.

    This also happens with the bluetooth drivers not as my GPS through a series of USB converter. or my palm for synchronization software.

    That is to say the problem is not just with bluetooth. It's with any program that uses a serial port.

    I'm afraid I might run out of com ports, and perhaps these unused com ports consume resources (are they built during startup?)     Hmmmm... Looks like I ran out of space... Al

    Hi again
    Well, I made a variation on your theme
    1 turned on or plugged in devices that could use a virtual serial port - 3 of them
    com 26 2 with one of them, I have attributed it to 25, then 24, etc. all the way up to 3 comm
    That unlocks (disabled the use in indication) for all of the unused ports.

    reassigned the 2 remaining ports to com 4 and 5

    Thanks for the help
    Al

  • Satellite pro A60 com port are not not in modem device manager

    Have a new A 60 pro and cannot connect to the internet via the modem.
    The offer of 'solutions' by help needed to make sure com port 1 was turned on, but only a lpt port has been listed.
    XP pro says that the modem works well.
    How to get com port 1?

    David

    Hey there,

    IM afraid that you do not have a hw to port com on the device. Com ports you have on the laptop are "virtual ports. If you're expriencing diffuculties internet connection, could you please go to Device Manager (by going to the system control panel and choose the Hardware tab) and then access the properties of the Toshiba software modem, go to the diagnostics tab and click the query modem button and display the result.

    See you soon,.

    PS you'll only com port listed in Manager of devices if and only if you have a serial port on the computer.

  • USB-232/2 shows the COM ports but not found resources VISA!

    Hello

    I use an NI USB-232/2 interface to connect my OMEGA Engineering temperature controller to computer. The thermostat communicates with the computer via hypertermianl and the configuration of the OMEGA software, but can not be detected by OR MAX I've attached a screenshot of my MAX of NOR. I could see the two COM ports, but I can't see the VISA test Panel.

    My problem is similar to the post problem OR USB-232! I tried the solution for uninstall and reinstall NI VISA both NI Serial, but still does not.

    OR Labview 2009

    OR MAX 5.6.0

    NEITHER version 4.0 Serial

    Version NOR VISA 5.4.1

    Temperature controller: Omega Engineering CNi1644-c24

    Spoke engineering application NOR two days, no solution. Can anyone help? Thank you!!!


  • USB/Virtual COM port Communication problem with ESP301/LabWindows/CVI

    Hi all

    I have gone through different threads posted in this forum for similar issues and all tried, but nothing helped.

    I'm trying to communicate to the ESP 301 training monitor via a USB port configured as a serial COM port using a CR. Have it ' command is to get the version of the controller. The "write" "ComWrt" command works fine but the read command throws and error ("-99 operation e/s timed out"). I tried all the suggessions; with delays etc... who has explained (resolved by Mr. RobertoBozzolo) in the thread posted here, which explains an issue similar to that of the mine, but the help couln t.

    The code is attached.

    I am using 2012 LabWindows/Windows7 64 bit multi-hearts

    int Get_Version () {}

    comport = 3;

    BaudRate = 9600;

    parity = 0;

    DataBits = 8;

    StopBits = 1;

    inputq = 512;

    outputq = 512;

    ctsmode = 1;

    xMode = - 1;

    Timeout = 5.0;

    com_status = 1;

    char comstring [6];

    DeviceName [] = "COM3".

    Int State = 0;

    char * error;

    int bytes_written = 0;

    char Cmnd_String [50] = "";

    char Read_String [512] = "";

    strcat (Cmnd_String, "ve?")

    strcat (Cmnd_String, '\r');  Tried to 0x0d
    strcat (Cmnd_String, '\0');

    length = strlen (Cmnd_String);

    assert (Cmnd_String [length] == you? \r\0'); Tried Cmnd_String [50] = ' VE? \r\0 ".

    DisableBreakOnLibraryErrors ();

    RS232Error = OpenComConfig (comport, devicename, baudrate, parity, stop bits, inputq, and outputq data bits) ;// tried ouputq = - 1 too

    EnableBreakOnLibraryErrors ();

    If (RS232Error == 0) {}

    com_status = SetCTSMode (comport, LWRS_HWHANDSHAKE_CTS_RTS_DTR);

    MessagePopup ("Comport verified',"CTS Mode works very well");

    com_status = SetComTime (comport, timeout);

    }

    bytes_written = ComWrt (3, Cmnd_String, (Cmnd_String) StringLength);

    If (GetOutQLen (3)! = strlen (Cmnd_String))
    ComWrt (3, Cmnd_String, strlen (Cmnd_String));
      
    status = ReturnRS232Err ();      The status is 0
    error = GetRS232ErrorString (status); / / error number

    Delay (5.0); / / trying to add the time up to 20.0

    GetInQLen (3); Returns 0

    ComRdTerm (3, Read_String, 512, 13); Read from inputQ

    status = ReturnRS232Err ();               Status to return the error code '-99 '.
    error = GetRS232ErrorString (status); Error message "e/s timed Opération" out

    return the situation;

    }

    Can anyone suggest where I am doing wrong?

    Thanking you in advance.

    Another thing you should check is baud rate.  The ESP301 by USB is expected than the baud rate to 921600.  The function for OpenComConfig() group implies that it does not support this baud rate setting, but it seems to work perfectly.

  • Problem with installing Windows on a hard drive, HARD drive does not get detected after installation

    Original title: help with hard drive of the computer.

    Flow of the problem:

    My aunt tried to install windows 7 on the previous copy of windows 8. Needless to say that it doesn't work and it has messed up the hard drive. So, I bought a vacuum. I formatted the hard drive using my other windows computer to have 2 partitions: a boot partition and system partition, and then used the program WinToUSB to install windows on the hard disk. The reason I did it is, because no matter how many times I changed the BIOS in my laptop of aunts, it wouldn't boot from the DVD player to load the windows software. After a few hours, I found WinToUSB. Once windows has been installed, I plugged it into the laptop. For a few hours, I didn't know what to do, because the computer does not recognize the hard drive (he said: "Not detected"). I decided to start from legacy, and then the screen deals

    «intell...» »

    and a bunch of dates, etc all the stuff on the screen to load legacy if you know what I mean.

    He said "not plugged in the media. Check the power cord.

    Then quickly changed screen before I can read almost anything and it goes to the normal windows screen black (with 4 colors). I said to myself, how can he be loading if the hard drive is not detected... Once it is loaded, he brought me to the blue screen (blue screen of death, if you want) I turned the computer on again, always noticing the hard drive was not detected. I ran all the recovery/repair options I could and turned off the laptop. I came back a few hours ago and I loaded the computer again and went into the BIOS.  He said that the hard drive has been detected and said the news about this, as usual. However, at the start of the legacy of windows loading screen, it said still not detected.  I then started to windows to see since it is now detected if that fixes the blue screen. Yet, there is no. I tried to go to the normal windows and screen remains blue. any ideas?

    Hello Chris,

    Thank you for visiting Microsoft Community.

    According to the description, it seems that Windows was not properly installed on the hard drive. I'm not sure how to work the software from third-party manufacturers WinToUSB and reliable installation process is. Microsoft does not recommend using any third party tool to install Windows on your computer, the use of these third-party tools can cause serious damage to your computer.

    I would say to format the hard drive once more and try to install Windows through normal Windows installation process.

    Refer to the section "using the installation option custom if no operating system is installed" in the thread below.

    Installing and reinstalling Windows

    http://Windows.Microsoft.com/en-us/Windows/installing-reinstalling-Windows#1TC=Windows-7

    If you are not able to install Windows on the hard drive at all, I suggest you to contact the hard drive manufacturer to obtain a diagnosis of material performed on the hard drive.

    Do not hesitate to write back for any further assistance with Windows, we will be happy to help you.

  • com ports are not not in Device Manager

    Windows Vista Ultamate

    I need to find what my gps device usb com port is turned on and set manually baud rate etc.
    Went to control panel option "Hardware and sound" not shown.
    Find Device Manager via "system" in the control panel but "ports" were not.

    Apart from evolution into another version of windows, what should I do

    You can add Ports manually via the control panel "Add Hardware". In the Add Wizard of material, choose the option "Install the hardware that I manually select from the list (user)" then click on the button "next".  Under "Common hardware Types" scroll down and clilck on Ports (COM & LPT) click the button "Next" and complete the wizard.

  • HDD not getting detected on the host virtual esxi nested 5.5

    Hi all

    on my home office, I installed ESXi on bare metal on USB. From a laptop computer, I was able to connect to it. I created an esxi embedded and followed

    Howto: create a nested laboratory However, it did not help.

    On the bare metal Office the esxi is able to recognize the network and it works fine.

    The nested esxi is not abkle to see the hard drive. Anu suggestions?

    Thank you

    Vaibhav

    ESXi you selected as the operating system for the nested host? What model of HARD disk controller is used for one or more hosts that are nested.

    André

  • Need 16 to 115 200 serial ports, can not get more 8 then

    I try to get 16 to 115 200 serial ports send/receive data. I have a NI PCIe-8431/16 (RS-485/422).

    I managed to get 8 ports will at the same time but not anymore. I tried 9 ports at a time and I get timeouts on port 9.

    PC: Dual core 2.4 GHz, 4 GB of Ram. I'm not more taxing on the CPU, I mean its 115 200 what treatment he would need.

    I'm already talking with OR to the care, but so far they don't have a definitive answer of fix. I thought that maybe windows XP can handle 8 ports?

    I also tried to use 8 of 16 channels and 1 another card 4 ports, I've had. Always the same results. I can do 8 simultaneous connections, sending data. and it seems that I can get the 9th to send to 2400 baud, but when I switch to port to 115 200 speed it fails / timesout?

    More information about my project: I am trying to update firmware on 16 devices at once. To 115 200, it takes 6 minutes to push all the code of the device.

    Process is: 2400 baud get version and check if a new version is necessary. 2400 baud say im switching machine for 115 200 2400 baud response. 115 200 baud send start download receive response to 115 200 baud rate. Send the bytes start and spell then line of the file at a time. Send end. done bytes.

    Anyone know of possible limitations under XP or with the device OR? Any help or idea would be apreciated.

    worst case I limit to 8 at a time. which is useless then. Might as well buy a controller at 8 ports and make a smaller device...

    Well, I fixed my problem with the help of using NI SPY on serial ports. Thanks for this idea of troubleshooting, first time I had to use or spy.

    First problem was my 100msec device timeout of 2400 baud to 115200 baud of switching. I added a loop for, 5 time, delays from 20msec (total 100msec) to send 'start download' and also to receive a response, after the transmission change. This allowed the unit to wait for firmware.

    Then I noticed that I had a ton of failure during the download. Process is send receive some line of code 0 x 01 that the code was excluded, then send the following line of code. If she gets 0 x 01 has not received or 0x02, and then send it again (forever if you want, well I think that several seconds until the device stops data receiver)

    My problem here is that I sent the data line, then read 1 byte. Timeout is set to 500msec. My code would get a timeout, so I'll send the data once again, since I have not received of 0x01. For some reason, it does not. After that I get the timeout I can't send/recieve on this port. I have then close and restart.

    Fix was a loop (20 times?) for 500 msec and check the receive buffer. If the receive buffer is empty after 500msec I try again. If the receive buffer has data then I read and check to 0x01. If I don't get 0x01 I try again. Otherwise, send the following line of code. It works very well.

    Finally, I can picture 16 devices in less than 7 minutes. This should normally be one at a time for 7 minutes each using a matrix of series 48.

    Next challenge 48 serial ports!

    Thanks for the help.

Maybe you are looking for

  • All tabs have disappeared; No file, messages, tools, help, tabs, cannot get or send emails. I have the Inbox, trash, drafts, local folders only.

    First of all, I noticed that my send button disappeared. My thunderbird e-mail account is now entirely free tab no operation at all. How can I fix?

  • ResultCode WWF00F009 WKSVDK

    When I started my laptop T530, I received a warning from the Solution Center that is installed. Under check-up it reads: Hardware Scan failed with result code: WWF00F009-WKSVDK. I searched this forum, but ould is not a great success. Please support m

  • HP s7610uk Slimeline desktop

    I have a HP Slimline desktop s7610uk when the Tower defends DVD writer did not eject, however if you tilt or lay Down it opens OK, is this a fault or just some kind of security thing to stop the DVD to find badly loaded or something and so need repla

  • Driver/software download Causes system closure

    I am trying to download the software/drivers for Photosmart C7180 A-i-O and at halfway, my Windows XP Service Pack 2 system displays error 1073741819 NT Authority\System and stops. Can find no system encounters an error, virus etc. and autoexec.nt is

  • Sync HTC evo problems.

    Original title: help please HTC EVO 4 G SmartPhone/Ive never got the same result twice using windows vista and an htc evo sync.mite sync.mite not, mite be a min, mite be an hour by downloading an update.