Vista has stop to connect to my network at boot time.

Similar Questions

• Vista has stopped turning the games run for a long time.

  Vista has stopped turning the games run for a long time. The display would go crazy and the sytem would lock. Gotta make a stop with the power button. No errors are recorded. I re-installed the game. Same thing. I reinstalled Vista 64. Same thing. I get about 3 minutes in the game and then locking the. 1 single game still work (BioShock2). COD - MW2 and COD MW lock the sytem. One is direct install, and the other is the steam. I have a video card Nvidia GTX 280 with the latest drivers from Microsoft. Before the reinstall, I tried to install the most recent NVIDIA. Did not help. Yet the locks without showing error. About half of the time it stops at my off video card a few seconds after that the display goes crazy. BioShock uses DirectX 10, and others use DirectX 11. I read on some sites that 11 causes the video crashes on some systems. I want to know is why 11 is working for so long and stop NOW. Is there a way to make the games all run on 10? COD BlackOPS crashes too. I played ALL these games over and over again until the last 3 weeks. If there was some error to post logs I would but there is not. Any suggestions on where to find some kind of problem that could cause this? The video card was removed, cleaned and put back into the computer. Still crashes. 1 in 4 of the games will take place without any problems. 3 will be blocking of the computer and the video trash in 3 minutes or less to start the game. The video is great, until blocking.

  Suggestions on how to fix or where to additional troubleshooting for the cause will be greatly appreciated.

  Try running the memory and the hard drive scan to make sure that both are good.
  http://Windows.Microsoft.com/en-us/Windows7/diagnosing-memory-problems-on-your-computer
  http://Windows.Microsoft.com/en-us/Windows7/check-a-drive-for-errors

  If both check good, the map may be at fault. In which case it is overheating you can manually increase the fan speed in the Nvidia Control Panel.

• Some applications stopped the connection to the network, while the rest of them still not connect...

  A month ago, I realized that Hulu Desktop not working not. Gives me a generic error message. but nothing else. I thought that it was related with Hulu Desktop, then, naturally I looked for support on their site.

  During this time, I realized application Pandora AIR One did not work either. I thought that this might be related with Adobe Flash player or Adobe AIR. My first goal turned in this sense.

  Then I finally realized than iTunes, and also stopped the Cisco VPN client connection to the network.

  I use these applications on a daily basis, make none of the apps took about two weeks. Try to find a common solution in question, and possibly on another two weeks...

  Moreover, the rest of the applications work fine, no glicth: these are some of the applications, I use every day without any problem:

  • Internet Explorer
  • Chrome
  • Firefox
  • Opera
  • Safari
  • FileZilla FTP

  First of all the error messages I get:

  Windows Sidebar Gadgets (Weather, RSS Reader, etc.)
  Unable to connect to the service.

  Cisco AnyConnect VPN Client
  Connection failed: the host is unreachable.

  Hulu Desktop
  We're sorry, but Hulu Desktop is unable to connect to the server.
  Please check your internet connection settings and try again.

  Pandora
  Your computer has problems of connection to the network.
  Click 'connect' to try again.

  iTunes
  iTunes could not connect to the iTunes Store.
  Make sure your network connection is active and try again.

  This is the only application error messages. Windows is not trow an error.
  Here are a few things I tried, with the hope of resolving this problem of connection of mystery:
  (not in this specific Ref. necessarily)
  • Wireless connection with wired connection of switch to a router
  • Connect my laptop directly to the cable modem
  • Turning off Windows Firewall (firewall)
  • Reset the Windows Firewall to the default settings
  • Deactivation of Microsoft Security Essentials (anti-virus)
  • Open the computer in Mode safe mode with networking
  • Uninstall and reinstall these applications and the related necessary subsets such as Flash Player, AIR, etc.

  A friend suggested the creation of a local account on Windows. So I tried that too. I created two accounts; an admin and a guest. Not surprisingly (!) these requests, I'm having problems for almost a month or two, worked. No error message, just worked.
  Here's the thing: I still don't know what's causing this problem on my main account from the system.
  I can move all my settings and configurations of the new account system. But what happens if these problems occur again. It's already a big hassle, autour file transfer and the account settings.
  Has anyone out there have similar problems and/or has the answer, please help me. It's so frustrating. I appreciate any leads or you can provide solutions.
  Thank you
  Osman
  p.s. I do not think that everything is relevant but here's HW and SW Details:
  Windows 7 Professional 64 bit
  Dell Precision M4300 laptop
  All the toutes les mises updates update Windows Update, all mentioned applications, drive, Flash, AIR, etc are up to date.

  I found the solution. :-)

  Open Internet Options, Advanced tab. Click the reset button in the box 'Settings reset Internet Explorer'.

  My applications are now online.

  Read this article if you need help to reset IE:

  http://Windows.Microsoft.com/en-us/Windows7/reset-Internet-Explorer-settings

• Satellite A100 - 049 (PSAAR) - registration of Windows Vista has stopped working

  My Toshiba Satellite A100-049 (PSAAR) came loaded with Windows Vista Home Premium.
  On each occasion my computer boot the, "record of Vista has stopped working" message.
  Here are the details of the error message below.
  Anyone have a similar problem or have a solution to this problem?

  Problem event name: CLR20R3
  Problem Sig 01: Toshibaregistration.exe
  Problem Sig02: 023.0.2538.28272
  Problem Sig03: 45801f61
  Problem Sig04: System.Managment
  Problem Sig05: 2.0.0.0
  Problem Sig06: 4536f344
  Problem Sig07: 111
  Problem Sig08: 123
  Sig09 problem: access to the authorization system
  OS Version:6.0.6000.2.0.0.768.3
  Local ID: 6153

  This happens especially if someone install a clean Version of Vista.

  Please call Microsoft. You must activate Vista by phone.
  As far as I know the phone call is free. After that it all works again.

• Error message: check of Vista has stopped working

  ARG.
  After that a few days of use, I get this error:
  Registration of Vista has stopped working.

  This happens every time I restart the computer.
  I tried to look around a gace, but I can not even find anything on the subject.

  Anyone who has got any ideas?

  Great info. Thank you for this

• Windows Vista has stopped working properly

  
  

  I get a problem report that says that Windows Vista has stopped working properly. It is said to know if I have 32 or 64 bit system. For this I am told to click the Start button, click computer. When I click on start I get a computer. What should I do now?

  "pastafasul" wrote in message News: * e-mail address is removed from the privacy * .com...

  
  

  I get a problem report that says that Windows Vista has stopped working properly. It is said to know if I have 32 or 64 bit system. For this I am told to click the Start button, click computer. When I click on start I get a computer. What should I do now?

  If you see the icon on the desktop, do a right click on that and then left click on properties. The window that opens has all the information you need.
   
  If no icon, and then start Windows Explorer and right click on computer it followed by the left-click on it.

• Photoshop CS3 does not start with popup indicating that "licensing for this product has stopped working" I tried uninstalling and reinstalling 3 times, including after you run CCCleaner tool.  Any help would be appreciated?

  Photoshop CS3 does not start with popup indicating that "licensing for this product has stopped working" I tried uninstalling and reinstalling 3 times, including after you run CCCleaner tool.  Any help would be appreciated?

  Same fixed.  At executed license repair tool, Adobe - Adobe licensing repair tool, and it fixed the problem.

• Vista has ceased to connect to Internet while XP works fine

  I was able to connect laptop computers XP and Vista desktop for a few years.  This week my Vista desktop becomes suddenly as a local connection to 'unidentified network' wireless so no Internet.  When I plugged the Vista desktop with a cable, that I could not he was looking for a username and password for the ISP to allow the connection.  Verizon technical support could not fix the problem - says no user name or password is required - with the lack of connectivity wired and wireless.  Is it just a Vista problem?  A recent update Windows change something that has caused this problem?  I noticed that this seems to be an unsolved problem here and on the Verizon forums.  It seems that this must be a Vista problem, due to the fact that XP has no problem connecting.  Thank you.

  Hi TinTheBear,

  Thank you for using answers Forum.

  In the future, I suggest starting your own thread about your question to get the right support.
  :]

  You can check for third-party wifi software that may have been installed with your network card.
  If it is running and you try to use Vista to control network and password/password encryption settings, they may sometimes conflict and causes this problem.

  Since your able to login in safe mode, I'm curious to know how you did the clean boot, you mentioned in your message.
  "Disable programs and services at startup"-copied from your post.

  Here is a method to try:

  To help resolve the error and other messages, you can start Windows Vista by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts. This article describes how to solve problems in Windows Vista by performing a clean boot. This article also describes how to start the Windows Installer service and how to reset the computer so that it starts as usual.

  Note When you perform a clean boot, you may temporarily lose some functionality. When you start the computer as usual, the function returns. However, you may receive the error message, or you can experience the original behavior.

  If the computer is connected to a network, network policy settings may prevent you from following these steps. We recommend strongly that you do not use System Configuration utility to change startup options on the computer, unless a support engineer Microsoft directs you to do so. This can make the computer unusable.

  a. log in the computer using an account with administrator rights.

  b. click on start toreduce this includes this image, type msconfig.exe in the Start Search box and press ENTER to start the System Configuration utility.

  Reduce this includes this imageIf you are prompted for an administrator password or for confirmation, type your password or click continue.

  c. under the general tab, click Selective startup, and then clear the Load Startup items check box. (The box use the Boot file is not available.)

  d. on the Services tab, select the hide all Microsoft services check box and then click on disable all.

  Note Following this step lets services Microsoft continue to run. These services include networking, Plug-and-Play, record of events, error reporting, and other services. If you disable these services, you can permanently delete all restore points. Do not do this if you want to use to restore the system with the existing restore points.

  e. click OK, and then click restart.

  Step 2: Enable half the services

  a. follow steps 1a and 1B to start the System Configuration utility.

  b. click on the Services tab and then click to select the hide all Microsoft services check box.

  c. Click to select half of the check boxes in the Service list.

  d. click OKand then click restart.

  Step 3: Determine whether the problem returns

  If the problem persists, repeat steps 1 and 2. In step 2, click to clear half of the check boxes that you have initially enabled in the Service list.

  If the problem does not occur, repeat steps 1 and 2. In step 2, select only half of the remaining check boxes that are cleared in the Service list. Repeat these steps until you have selected all the check boxes.

  If only one service is selected in the list of services , and you the problem persists, the service selected the cause of the problem. Go to step 6. If no service is causing this problem, go to step 4.

  Step 4: Enable half of the startup items

  a. perform a clean boot by repeating step 1.

  b. click on the Startup tab and then click to select half of the check boxes in the startup item list.

  c. click OK, and then click restart.

  Step 5: Determine whether the problem returns

  If the problem persists, repeat steps 1 and 4. In step 4, click to clear half of the check boxes that you have originally selected in the startup item list.

  If the problem does not occur, repeat steps 1 and 4. In step 4, select only half of the remaining check boxes that are cleared in the startup item list. Repeat these steps until you have selected all the check boxes.

  If only one startup item is selected in the startup item list, and you still experience the problem, start selected in the list element is the service that is causing the problem. Go to step 6.

  If no startup item causes this problem, a Microsoft service most likely the cause of the problem. To determine which Microsoft service may be causing the problem, repeat step 1 and step 2 without selecting the hide all Microsoft services check box in each step.

  Step 6: Resolve the problem

  After you determine the startup item or the service that is causing the problem, contact the manufacturer of the program to determine if the problem can be solved. Or, run the System Configuration utility, and then click to clear the check box of the element of the problem.

  Step 7: Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  Click on start toreduce this includes this image, type msconfig.exe in the Start Search box and press ENTER.

  Reduce this includes this imageIf you are prompted for an administrator password or for confirmation, type your password or click continue.

  On the general tab, click the Normal startup option, and then click OK.

  When you are prompted to restart the computer, click restart.

  Please let us know if that helps.

  Chris
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Computer Windows Vista says it is connected to the network 4. I don't know what is network 4.

  on the bottem of my screen where the icons were similar to the he mcfee icon and symbol of volume there is a picture of 2 small computer screens, and when I scroll above him, it says connected to the network 4. I don't know what network 4 is and I have never seen this before and the other day I saw him and it says connected to network 2. I would like to know if anyone can help me in this matter. What network average 4?

  original title: bottem icon

  This icon is the icon of your network. You don't say what kind of network you are using. However, I will give you an example. If you repeat your network connection or use a network USB key and plug the key to another USB socket and create a new Windows login will name each new connection 4 then 2 then 3 and so on. You can rename the connection to your liking. To rename the link to right click on the network icon in the notification bar, click Network and sharing Center, click on manage network connections, right-click your network connection icon and click Rename.

• Windows Media Player in vista has stopped playing my video files (.) MOD extensions)

  My Windows media player recently stopped playing my video files that have a. Extension of MOD, although the audio is not yet once the video is crushed. When the video freezes a computer bubble lets me know that the driver igfx has stopped working and then recovered.

  I spent many hours trying to solve this problem. My graphics card is an Intell chipset and it is up to date with his driver (I checked), the motherboard is an ASUS and this is far too - I checked. I ran an auto fix and that disabled four codecs, but the problem persists. I have run the sfc / scan now processes at the prompt as an administrator and it came clear.

  The problem is driving me crazy! can anyone help? When I play the video on another computer that works under XP, I have no problem.

  Thank you

  John.

  I fixed my own problem finally - I took this advice:

  http://answers.Yahoo.com/question/index?QID=20081217192010AAFUBeK

  and installed "essentials pack windows media codec 3.2 [32 bit], this source http://www.snapfiles.com/get/essentials-codec-pack.html.

  Job done!

• Windows Media Player (32-bit Vista) has stopped working. It does not open when I click on a file that uses or from the main menu. I tried to download and re - install, but get the message "you already have the latest version of Windows Media Player.

  Windows Media Player does not work for music or videos (Vista)

  Hi Palmdoc,

  1 when was the last time it was working fine?

  2. did you of recent changes on the computer?

  You cannot uninstall and reinstall Windows media player in Windows vista, because it is integrated inside the operating system.

  This problem occurs because the Windows Media Player library database is corrupted.

  See the below Microsoft article and try the steps mentioned, check if it works.

  You cannot view, add, or delete items in the library of Windows Media Player 11

  http://support.Microsoft.com/kb/925718

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Problems connecting Xbox 360 to computer vista laptop via ethernet connection to the network local (the laptop is connected via wifi)

  I spent a few hours trying to solve this problem, and I've been to countless forums.  They all told me to go into "Manage network connections" and right-click-properties on my connection Wi - fi.  Then they speak by clicking on the tab sharing... which I did not.  I don't know how to share my connection to the WiFi with my xbox 360.  It is supposed to be easy, but I can't realize what is designed as "highly probable."  I have a laptop Sony Vaio VGN-FW390 and Vista Home Premium. Maybe I have to set up a connection to an access point, or do a sort of thing ICS... I do not know.  I am incredibly annoyed by this, and I'd appreciate any help.  Thank you.

  Messier,
  Thank you for visiting the Microsoft Answers community forum.

  Try this and see if it works for you, it has worked for some users.
  With no cable connected between the computer and the xbox, go to control panel, network and sharing Center. You should see a "Local Area Connection", which will show disabled at this stage, and your "wireless network connection", which should show connected. Connect the ethernet cable to your laptop and the back of the xbox. Select the 'connection to the Local network. After that it is well connected, disable your 'Wireless Network Connection'. Once disabled, right click and click Properties. Go to the Advanced tab and check "allow other users of the network to connect through this computer's internet connection". Once this is done, your wireless internet connection should say shared next to the State of the connection.
  Turn on your wireless connection. Then, right click to 'connect to the Local network' and click on repair. Allow the end. test the connection on your xbox.

  Let us know how that works for you.
  Thank you
  Gloria
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows Vista has not saved password for shared network folder

  Whenever I try to open any resource on our network, it always ask password click even RECORD on several times. I checked in the credentials manager, there is no password is saved and I tried to add the IP network to share resources, but also has not worked

  Hello
   
  1. who is the edition of Windows Vista installed on the computer?
  2 you get an error message when trying to access the network resource?
   
  Please, try the following steps and check the result.
  1. click on start, type control userpasswords2 and click on enter.
  2. on the window user accounts, on the users tab, click the Add button and add the details of the user.
  3. click on the Advanced tab on the window user accounts, and then click manage passwords.
  4. click on the Add button, add the details and select the type of credentials according to your requirement.
  5. apply the changes and check the result.
   
  Visit this link for more information on "Troubleshooting network connection problems":
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems
   
  I hope this helps.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• Firefox 3.5.1 running Vista has stopped working. No error message. Tried to uninstall and install also the latest version and get a message saying that I must first close Firefox (which of course obviously does not work)

  Firefox 3.5.1 running Vista stopped work, no error message. Tried to uninstall and install the updated version. Download the message that I first need to close Firefox, but it is not obviously executed.

  This has happened

  Don't know how many times

  I restored my system to an earlier date, December 2009

  User Agent

  Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.0; Trident/4.0; SLCC1; .NET CLR 2.0.50727; Media Center PC 5.0; OfficeLiveConnector.1.3; OfficeLivePatch.0.0; Dealio Toolbar 3.1.1; .NET CLR 3.5.30729; .NET CLR 3.0.30618; NET4.0C; AskTbWCL/5.8.0.12304)

  Firefox can not run visibly, but is probably running in the background. It is in the Task Manager. To access the Task Manager go to Start and type in taskmgrsearch field. This will open the process task manager. Then go to the tab processes and end firefox.exe. After the end of this process, close the Task Manager and try to re-run the installation/uninstallation.

• DeskJet 3051 has - having problems connecting to the network of Verizon MiFi

  I have a wireless Deskjet 3051 a home printer. I use it with a Macbook Air. Our wireless network has changed, and I need to connect the printer to the new network, which is a Verizon MiFi network. Is there a way to do this? I tried to restart the printer, nothing helps. When I try to install the software from the installation CD supplied with your printer, it is said that the operating system I use is not supported by the software. Help me, please!

  Hello

  If you have already installed the software of HP full feature temporary connect the printer using USB, go to Applications > Hewlett-Packard > peripheral utilities and follow the HP Installation Wizard, you will be provided with an option to connect the printer to your network.

  If there is no Hewlett-Packard folder under applications do not connect the printer using USB, download and install the software below. Be sure to select the HP recommended software and you will be provided with the option to set up the connection Wireless during installation:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=Al-107372-1&cc=us&DLC=en&LC=en&OS=219&product=5117616&sw_lang=

  Shlomi