Vista will not work to open/run programs and some files, especially if necessary administrator auth.

Hello

I ' v got a computer toshiba laptop Vista x 32. Last week he began to do a lot of strange things that are quite annoying.

First of all, when it is connected to two networks wireless or ethernet, explore and chrome, open and run fine but the network in the tool bar icon has a red x on it. When I try and open the network and sharing Center, it crashes.

This causes the following problem. He now does open kind of folder on the drive hard or Administrator program needs approval. Previously, I would get the dialog box and screen gray, but now he is nothing when clicks or opens a new window but crashes. Other programs such as itunes does not open, but the office is strangely very well...

Also, when online any kind of e-mail attachment or program download does not work. Shockwave flash blocks on bbc iplayer, but youtube works. Cannot open the PDFs online or

Everything works normally in safe mode and from there, I ran Defrag, disk cleanup, auditor of errors and a 2 system restore nothing doesn't. I also tried the software audit tool microsoft malicious who found nothing.

Is there anything else I can do? Any advice would be greatly appreciated!

Thank you

Matt

Hello

I ' v got a computer toshiba laptop Vista x 32. Last week he began to do a lot of strange things that are quite annoying.

First of all, when it is connected to two networks wireless or ethernet, explore and chrome, open and run fine but the network in the tool bar icon has a red x on it. When I try and open the network and sharing Center, it crashes.

This causes the following problem. He now does open kind of folder on the drive hard or Administrator program needs approval. Previously, I would get the dialog box and screen gray, but now he is nothing when clicks or opens a new window but crashes. Other programs such as itunes does not open, but the office is strangely very well...

Also, when online any kind of e-mail attachment or program download does not work. Shockwave flash blocks on bbc iplayer, but youtube works. Cannot open the PDFs online or

Everything works normally in safe mode and from there, I ran Defrag, disk cleanup, auditor of errors and a 2 system restore nothing doesn't. I also tried the software audit tool microsoft malicious who found nothing.

Is there anything else I can do? Any advice would be greatly appreciated!

Thank you

Matt

First check if your drivers are working properly, go to control panel, then Device Manager, then make sure that all of your drivers. Avoid any sign of danger on them if there so try to update or uninstall, or back the driver to resolve the problem.

Then, make sure that your system is clean. using the analysis

http://www.Malwarebytes.org/

http://www.systweak.com/antispyware/ and try

a-squared emergency USB key

http://www.emsisoft.com/en/software/download/

http://www.Avira.com/en/download/index.php

http://www.SurfRight.nl/en/downloads/

then clean your system of unnecessary files using http://www.filehippo.com/download_ccleaner

then if the problem persists then prepare your computer to clean boot by typing msconfig in windows searchbox in startmenu, then press on enter then disable all startup items and any of the services of windows, then restart! see if it makes a difference? If she did then go back and see that caused the problem.

Tags: Windows

Similar Questions

  • my epson dx4050 will not work or open I use wind 7 now, but it does not work pls help

    my epson dx4050 will not work or open I use wind 7 now, but it does not work pls help

    Because your message was clearly not your comments on the web site of MIcrosft responses, I have he left the comment forum in the forum 'Hardware and drivers' Windows 7.

    When you say it "will not open', do you mean physically or you want to tell the printer object in the printers and devices folder does not open when you double-click it?

    Have you tried to delete the printer and add it again?

    He has already worked?  If so, have you changed between yesterday and today?  The device is supposed to be compatible with Windows 7 and should not need a separate driver, but if you have Windows 7 32 - bit, you can try using the driver on the Epson website.
    http://eSupport.Epson-Europe.com/FileDetails.aspx?LNG=en-GB&data=lkuCfcvA9cw77whFcRdwis4JOQH9mtNd&ID=324678

    How do you connect to the Stylus DX4050?  It is USB, wired network or wireless network?  The documentation says it is USB, but I connected USB printers to the network, then maybe you have as well.

    The more details you provide on your printer and your system, the better people can help you.

  • Grid of fluid will not work in IE11? Firefox and Chrome is very good. Any ideas?

    Need help on this one.

    I'm new to grid of fluid and I must say a bit of an amateur to Dreamweaver, but I get.

    I can create pages of fluid grid without any problem. Although this will not work with IE11. Chrome and Firefox works fine.

    I am also having the same problem with the fluid grid of Dreamweaver templates. I am confident in saying, I do everything correctly.

    Has anyone encountered this problem?

    By "does not" what does not work exactly?

    View?  Questions from the media?   Page layout?

    Using IE in Compatibility Mode which is essentially like display in IE7?  Try to disable Compatibility Mode to see if things improve.

    Nancy O.

  • Windows Vista does not work - cannot open Control Panel control and IE

    original title: Windows Vista does not work properly.

    Hello

    I have Windows Vista Home Premium running on Lenovo laptop. Recently, I cann't open the browser IE, the same panel. I don't have a Vista CD. But I have the product key provided with the laptop. Please, help me to make it fully operational as before.

    Assuming that you can always connect to your computer in normal mode:

    Run a check of the filesystem to find corrupted files and repair them if possible.

    Start button > Search box type cmd > look up, do a RIGHT click on cmd.exe > click run as
    Administrator
    > in this window type cmd black and white, on the
    flashing fast sfc/scannow > press the ENTER key.
    Note: there is a space between
    'sfc' and ' / '.
    To sit and wait. It will take time.
    When finished, exit the cmd window.
    Reboot (restart your computer)

    After that, check if you can run the computer as well as to access the IE.
    If IE still does not work, use the following tutorials...

    1 Internet Explorer does not start or stop responding
    http://support.Microsoft.com/kb/926449
    Note: It has an auto FixIt application. Use it.

    2. Internet Explorer Add - ons problem when IE hangs or freezes
    http://support.Microsoft.com/mats/ie_freezes_or_crashes/en-us
    Note: there also an Fix It self.

    3. to resolve network connectivity problems in Internet Explorer
    http://support.Microsoft.com/kb/936211

  • Vista will not play the video portion of my avi files

    I have a ton of my Canon camera avi files. Windows Media Player does not display video (Vista or XP), but the sound is very good. I can't play using Real Player on a XP machine. Real Player on Vista will not display the video either.

    I have a ton of my Canon camera avi files. Windows Media Player does not display video (Vista or XP), but the sound is very good. I can't play using Real Player on a XP machine. Real Player on Vista will not display the video either.

    ==================================
    No guarantee... but it may be worth trying to download
    and install the following free codec pack:

    FWIW... it is always preferable, if you create a system restore
    point before installing any software or updates.

    * Proceed at your own risk *.

    Info on CCCP (combined Community Codec Pack)
    http://www.CCCP-project.NET/wiki/index.php?title=Main_Page
    John Inzer - MS - MVP - Digital Media Experience - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

  • Did not win 10.  I'm back to Win 7, player will not work.  Don't delete and reinstall.  Help please.

    Tried to win 10 and don't like it.  When back to Win 7, Acrobat Reader will not work.  Make me

    "the Acrobat PDF DC browser plug is missing
    Please reinstall Acrobat Reader DC for this problem"

    Also receive "the older version of Acrobat DC cannot be removed" Contact tech support group

    Try to install it becomes: "the network function you are trying to access is unavailable.

    Try to remove and reinstall doesn't work can not remove the old version and it will not reinstall it

    Please help.  Thank you, Scott Boyd [email protected]

    Try to use this tool: Download Adobe Reader and Acrobat tool - Adobe Labs

  • Activation key for Vista will not work

    Re-installed Vista (valid copy) 3 times on different computers in the House and then tried to intall on your laptop - now the product key does not work. So rather than buy a new product key for Vista, I prefer to get Windows 7 but do not want to spend $$ if he's not going to work. The laptop is stuck on activation without another internet access a screen that direct me to Microsoft to buy a new product key for Vista. Try to install Windows 7 with a drive will overwrite all this nonsense Vista activation?

    Hi joelmc26,

    If you have a product key then this "only" usable on computer product key "a". If you used the key poroduct to simultaneously install Windows on 3 different computers you're wearing violation of your license agreement. To be honest, if you do this, then I'm surprised that you got that day. If you install windows on another computer "you" he remove it completely from the previous computer.

    This error message receive you about activation? Already used, for example product key? To obtain the active product you must telephone Microsoft. See this link from my Web site:http://vistasupport.mvps.org/product_key_already_in_use.htm the service is automated, but you will get finally a 'real' person, if you carefully follow the instructions on my Web site. If you use the same product on three different computers you will not get an activation code. If, however, you have taken off a Windows Vista-based computer and then install on another, then you need to explain it to Microsoft. Then it's support technician if it gives you an activation code. If everything is legal and above all Council then there should be no problem.

    This forum post is my own opinion and does not necessarily reflect the opinion or the opinion of Microsoft, its employees or other MVPS.

    John Barnett MVP: Windows XP Expert associated with: Windows Desktop Experience: Web:http://www.winuser.co.uk;  Web: http://xphelpandsupport.mvps.org;  Web: http://vistasupport.mvps.org;  Web: http://www.silversurfer-guide.com

  • EZ grabber (Vista) will not work with Windows 7

    MY EZ Grabber (video capture card) is working on an old machine running Vista nut does not work on my new HP running Windows 7.

    Any ideas would be appreciated, thanks.

    Thank you for this

  • Windows Vista upgrades not work - error code 8007065E, 80070641 and 641

    Original title: windows Vista upgrade does not

    I tried to run updates and constantly getting the following errors:

    code 8007065E,

    code 80070641, and

    Code 641

    but can't them solved using Microsoft?

    Hello

    Did you the latest changes on the computer before this problem?

    Before the windows update follow the methods check if it works very well.

    Method 1: Put the computer in a clean boot state before proceeding with the installation of windows update.

    How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

    http://support.Microsoft.com/kb/929135

    Note: After installing windows update, follow step 7 in the link provided to return the computer to a Normal startup mode.

    Method 2: Temporarily disable the security software.

    Disable the anti-virus software

    http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

    Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

    Method 3: Run the Windows Update Troubleshooter.

    The problem with Microsoft Windows Update is not working

    http://support.Microsoft.com/mats/windows_update/en-us

    Method 4: Follow the steps in the section provided.

    How to reset the Windows Update components?

    http://support.Microsoft.com/kb/971058

    Difficulty of corruption problems MSI software update registration

    http://go.Microsoft.com/?linkid=9666880

    You can also manually install the update (numbers KB) by downloading from the Microsoft Download Center.

    http://www.Microsoft.com/downloads/en/default.aspx

    It may be useful

  • HP Photosmart premium c310, Windows 7 (64 bit) series will not work afterit is turned off and then on again

    I have photosmart all-in-one c310 printer and whenever we have a power outage, the printer will not print at startup power upward. I have spend hours trying to download drivers or updates and check the printer that says it's fine and the computer that says it can't find the driver. The last 2 times I finally got running again, but I did something different every time and I don't remember what it was. I just spent 2 hours on a hamster wheel keeps back me for a download, after you download it twice, I finally understood was the SAME download (the 3rd time I was directed here) and the printer STILL does not work. I'm pulling my hair out and I'm about to throw this worthless piece of scrap metal by the window. Help!

    Are you connected wireless? If so, you will need to reconnect the printer to the network of the SCW wireless on the printer itself. When you have power, he can hit just the printer off of the network from the router and just reconnect.

  • My CAD U37 USB Microphone will not work supposed to be Plug-And-Play.

    I recently bought the microphone she appears under windows 7 as 'C-Media USB Audio Device' as it is supposed to, but it can't find the drivers. I talked to the developers, and they said that it meant to be plug-and-play drivers are native to windows.

    I plug it into my laptop which is running XP and it works very well.

    I tried all usb ports I have, I unplugged everything just got the mouse/keyboard and the monitor.

    Nothing seems to work, please help.

    Hello

    Please contact Microsoft Community.

    I suggest you follow the suggestion provided by Rajesh Govind responded on 19 March 2013 from the link below and check if it helps.

    http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-hardware/my-headset-microphone-not-working-in-Windows-8/f4f1ad12-E7EA-4FFB-ac88-df5eed3298e6

    Hope this information was helpful and let us know if you need more assistance. We will be happy to help.

  • Vista will not start. Verifying the integrity of system files and repair has no ErrorCode = 0 x 2 HELP PLEASE!

    ASUS PC, Windows Vist Home premium, all updates.

    Out of the blue, it will not start.  Access the start scrolling (the one just before logon) screen and it just stops.

    Twice I ran Vista check utility.  The first time, I chose to do the system restore to previous state.  Restarted.  Always off.  The second time, it took much longer and from what I can see.  All TESTS PASS, except one:

    Repair action: repair and checking of the filesystem Integrety

    Result: failed. Error code = 0 x 2

    Time required: 6206818ms

    I get no blue screen, I can't even any screen!

    I'm triying to repar because I have several costly software titles that link the authorization key code to a key hardware and software installation.  I don't know that I could reinstall if I get a code (randomly?) different generated software.

    I don't know about i-tunes and other content downloaded my wife has such as MP3 files and audio books.

    Thanks for any help!

    The test fails (SFC) checks for corruption in the files on your system.  If she can't even complete, she suggests the Vista all system needs to be re-installed - but you have already done this and you still have the problem.

    In fact, look like a hardware problem.  Here are some troubleshooting guidelines hardware that can help (but probably not for this question as what you really need, it is a replacement for test):http://elephantboycomputers.com/page2.html#Hardware_Tshoot.  Frankly, I think it's time to take the system to a repair facility of good reputation for the service computer (or to return to the manufacturer for repair - costs, schedule, guarantees and make a decision).  I don't know what hardware component.

    If you can, try to back up your data before you import it it because they will probably wipe the drive clean during the process. You can use Knoppix http://www.knopper.net/knoppix/index-en.html with a good ISO as Copier: http://isorecorder.alexfeinman.com/isorecorder.htm as well as a blank CD (perhaps done on another computer).  This should give you enough access to the system (if you do not have any other means) to backup your important data.  Otherwise, try slaving the drive to another system and access the data in this way.

    I hope this helps.

    Good luck!

    Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • problem running programs and .exe files

    computer has been corrupted (by clicking on kids')-tried malwarebytes' anti-malware scan, when I rebooted, nothing works.  I tried microsoft security, but could not access the program.  I tried the system restore, but that no longer works.  If I try to download a program, do not automatically work .exe files and my computer asks me what kind of program to run it - nothing done!  I am missing shortcuts, applications, and system files.  I can't go to the Help Center to try a new date of system restore because application helpctr.exe is not found.  Any help?

    It is likely that your .exe and other extensions have changed my virus/malware.

    There is a simple fix as long as you can open regedit from the start > run box.

    As long as you can then go (I hope I'm not breaking rules here - url not mine but very helpful)

    http://www.dougknox.com/XP/file_assoc.htm

    Download the .reg and .exe association fixes. Use ' file > import ' option in regedit for each of the downloaded files. This should solve your problems. Best regards, Dave.

  • Vista will not work after the power to

    I have a HP Pavilion laptop with Vista SP 1 64-bit installed.  Tuesday, April 14 I turned it on only to freeze with in ten minutes after having informed me it had installed updates.  At first, I thought it was a problem with my browser and uninstalled FireFox.  This does not alleviate the problem.  I run my adware and spyware detectors to see if something to eat to the top of the RAM.  All scans were free of malware and it is free of all viruses as well.  It took me three tries to get even the scans indeed the computer would lock up after 10-15 minutes whenever I turn it on.  I thought maybe it was overheating and checked, but the CPU temperature is normal and the fan runs.  I tried a system restore to get rid the updates in case this was the cause of the problem since it had fixed the errors before.  No luck. On the first two tests, he wouldn't even finish the restoration of the system.  I ran the memory controller and it froze and then shut down the computer.
    It crashed last night, while I was running a System File Checker and everytime I try to start it in safe mode, it gets stuck on:
    Support: \Windows\system32\drivers\crcdisk.sys
    After sitting there for sometimes more than ten minutes, it starts as usual only to freeze up again.  I tried to boot into safe mode with network and just Safemode and he refuses to do.  I am very worried that I have a big problem, but I can't stay up long enough to do any in-depth audit.
    All the world had similar problems or might know what the issue could be or am I just screwed?

    Hello brohne,

    Please use the Microsoft Answers form. Because you can run the sfc command or get no results to start in safe mode, I recommend that you perform a repair installation.  This option allows you to repair you computer and all in keeping your documents.  PLEASE SAVE YOUR SYSTEM VISTA FIRST.  The link below explains how to perform a repair installation.

    http://social.answers.Microsoft.com/forums/en-us/VistaInstall/thread/58ed3b94-D603-4FEC-83CA-b3d15d1275b8/
    Thank you for using answers Forum. Please let us know how it works.

    Joseph
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • How Win764() will not work if I install programs elsewhere other than the default Program Files folders?

    The reason for this question is that I want both 1.) Learn more about Win7 64 bit works, as well as 2.) understand the scope of customization possible.

    In any case, first of all, what this scenario: what happens if I create a subfolder in each of the two Program Files folders? Say, in the (x 86) program, I create a subfolder called Programs (x 86). Or another name, whatever and say that I do the same thing for the Program Files folder. So, what happens if instead of installing all my software back into the default directory Program Files or program (x 86), what happens if I start to install in these subdirectories to the place?

    Everything works fine? I heard that these two Program Files folders have assignments to special access for security reasons. As I start working on these issues, the same security structure would be preserved, correct? Second, everything will work correctly not only wise, but in terms of features? I know that each of the Program Files folders also has its own common files folder. If I make my method, installed programs to put their files in the Common Files folder correctly, and then get back them properly when necessary?

    Finally, I would also like to know out of curiosity, what would happen if I don't use the program files directories at all and instead started to install things in a completely different directory. But that is less an issue for me at the moment. I just want to know if what I have set out above would be good or not.

    Thank you!

    Hi StormRyder

    This issue is beyond the scope of these level consumer forums.

    I would recommend that you post on the Technet ITPro Windows 7 forumsfollow-up questions. Advanced on these forums users are more familiar with these types of settings, and may explain some of the common pitfalls you may encounter, as well as how to be ready in case something goes wrong.

    I hope this helps.

    Thank you for using Windows 7

    Ronnie Vernon MVP

Maybe you are looking for