VMware ESXi WARNING - battery on the controller workload 0...

Similar Questions

• Battery on the Controller PERC 6 / i integrated Poweredge R900 and 2950.

  Hi, we have this error below Poweredge R900 and Poweredge 2950 for 4 days now, I hope that he will be gone after 7 days (such as by Maximum learning delay)

  Battery on the Controller PERC 6 / i integrated:

  Name battery 0
  Degraded state
  Loan of State capacity
  Learn the State duly
  Next time learn 0 hours
  Learn 7 days 0 hours maximum
  Learn the Auto Mode

  In case the error continues after 7 days, is there any solution to this? or replace the battery if error remains.

  I had been searching for the right part No. battery so that we can order in advance, thank you for giving the battery part No. for Poweredge R900 and 2950 Controller PERC 6 / i integrated.

  Thank you much in advance.

  concerning

  Rais info is stored on the discs should not be a problem

  R900 page 84 support.dell.com/.../XK9460D.pdf

  2950 page 74 support.dell.com/.../hom.pdf

• VMware ESXi does not support the RAID on HP Proliant ML110 G5 drives

  Hello

  I installed VMware ESXi on my HP Proliant ML110 G5. I got 3 hard drives on my server at the moment, one of them is VMware ESXi and other two are RAID1.
  Whenever I connect to my server via vSphere client I have the chance to see every HARD drive (datastore) separately.  Is it possible that VMware does not RAID installation?
  I would need to see these two hard drives as a data store. Do you have any ideas on how I can do?
  Thank you.

  like any other typical server, you need to configure the sata raid controller RAID5/RAID0. but keep in mind that this controller without any battery backed cache would have very horrible performance. Another way is that you can use datastore span to provide as a large store of data, but if you lose all of the computer, you will lose all data.

• VMware ESXi 4.1 and Areca controller

  I am trying to set up a home little uses ESXi 4.1 server to allow me to run maybe 2 or 3 virtual machines, but it does not recognize my Areca controller to install the operating system.  I managed to install the full version of ESX with the driver CD, but I don't see how to use the driver CD when installing ESXi, what are my options?

  ESXi 4.1 drivers are available on the website of the Areca here:

• Query related to multi site VMWare esxi 5 according to the installation program.

  Hi all

  We have several distributed sites based on vSphere 5 according to the installation program which are the ESXi host 5.1, 5.1 vCenter and a storage for each site... Now, we anticipate adding distributed locations all host esx to vCenter built one of our new site.

  So, what should be the best way to achieve this.

  (1) is it advisable to add the distributed over wan to vCenter site on a different location?

  (2) can we also go with modes related? Since all our existing site already live, do we need to re - install vCenter to have bound mode installed?

  Concerning

  Varun Khatri

  Hi, as long as you have enough bandwidth between sites, you can add you remote cluster to vcenter.  I've done this before and I had no problems.  Your approach depends on the configuration of your environment.  If you have existing vCenter installed on each site, you can use the linked modes, and you don't need to reinstall to set up connected mode. vSphere Documentation Centre

• Local users of VMware ESXi 5.5 for the oversight role of the CIM

  Hello, is it possible to create local users in ESXi and assign roles and permissions to manage only CIM interactions? I learned that local groups are not supported to 5.1 from. This means that we cannot add a role (for CIM Interactions only) for a local user created on ESXi? Please advise!

  Thank you!

  Why not give a user privileges? Maybe he needs admin access to host not only CIM interactions. Any problem with giving Admin privileges?

• Cannot import Microsoft Windows Server 2008 R2 with Hyper-V virtual machines to VMware ESXi 4.

  Hi team,

  I use VMware vCenter Converter Standalone to import certain Microsoft Windows Server 2008 R2 with Hyper-V virtual machines to VMware ESXi 4, using another Windows Server 2008 R2 as the machine Agent Converter. Well, the agent connects to the Windows VM source very well (I used the net use command to create a line of conduct...), perhaps no chance to connect to the computer target VMware ESxi 4 and make the converter doesn't work...

  Following is the error message:

  "Unable to connect to the host specified" from the converter agent machine. " It is perhaps because the host is not available on the network, there is a problem with the network configuration or management on this host services do not react. Check all components of converter to be able to connect.

  So, my question is; is it possible to create a work around (like the net use Windows command above) to make possible the connection of the converter Agent on Linux VMware ESXi 4 machine Windows machine, to directly import the virtual machines of Windows Hyper-V to Linux VMware?

  Thanks in advance,

  It's even easier than that

  Use this: http://www.winimage.com/

  Which will convert *.vhd *.vmdk, so you don't need to do all this... Of course, another way is to start the machines, leaving them on Hyper-V and go through the network and process virtual machine as physical machines and do a P2V on the network...

• HP Proliant Gen8 DL380e not charge controller B320i with VMWare ESXi 5.0 U3

  Hello community.
  
  Iam trying to install VMWare ESXi 5.0 U3 on a HP Proliant DL380e Gen8 server that has a B320i controller, I'm using support custom installation of HP, but yet when I select target the device doesn't show anything, I tried to raid 1+ 0 and raid 5, but I get No result.
  
  Ce is ISO which I download.
  

  https://my.VMware.com/Web/VMware/details?downloadGroup=HP-ESXi-5.0.0-U3-OCT2013 & ProductID = 229

  
  try Added to ISO customize the controller driver, but the ISO tells me that that driver already exists.
  

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?swItemId=MTX_0a122ebcbbac4c469ca9acd1ae

  
  In le BIOS J’ai activated the next option.
  

  http://h20564.www2.HP.com/hpsc/doc/public/imageServlet?docid=emr_na-c03907472-1/c03871500.jpg

  You can try the custom HP VMWare 5.5 ISO instead? Or do you need a reason 5.0 any?

  I'm running a Gen8 DL380e with 5.5 Update 1 without problems. 5.5 Update 2 has some problems about the new version of the hpvsa driver that gives massive drops in virtual machines to run.

  You have a BBU (battery backup) installed?

  It is also for the execution of the last PSP (Proliant ServicePack) to get the latest firmware and the BIOS before installing.

• With the help of ESXi 5.5 with storage controller HP DL120 Gen9 (HP H240 FIO active host Bus Adapter)

  Hi guys, I'm new to virtualization, but I couldn't find a solution for this. Feel free to correct my text because I'm not very experienced with this sort of thing.

  Background: I have a couple of servers and the end of the game will be left to create a San and run other systems within this SAN (providing network-level RAID). While in one data center I could decides to make a RAID at the level of the material in addition to RAID level network, now I want to save money on storage for this test so I want to do simple split disks (RAID/JBOD) at the hardware level. Because of the OS, we will virtualize later we use ESXi 5.5, 6.0 not.

  In fact, I had a small server supermicro I already installed ESXi 5.5 on that doesn't have lots of storage which will be the 3rd Member voting left.

  So I put the 2 servers (HP ProLiant DL120 Gen9 E5-2630v3 8 GB-R H240 8SFF 550W PS entry Server (777425-B21)) and I went into the BIOS/CMOS settings mode AHCI Mode smart-table (I don't remember the wording of it, I'm not in front of the machine). Then I went in the smart supply and went to the intelligent storage administrator part and I had to select "disable the RAID", or something like that. After the reboot, I went back and now my two drives appear as "Unassigned" which seemed reasonable to me. I tried to see if I could 'assign' but in mode no RAID, there is no means to assign what whatsoever because the paintings exist not primarily in mode non-RAID. I was not sure if there is a way to "initialize" them or something like that, but I couldn't find the parameters like this. My hope was that a BONE would now see these drives natively as a simple readers without the layer of abstraction to a storage controller.

  This does not work and when I run ESXi 5.5 from a USB it will boot, but when it gets to the part where you are supposed to select the ESXi installation disc on it only shows the USB itself and none of my SSD.

  Does anyone know how to configure the adapter HBA H240 with ESXi 5.5? I could really use some help from someone who has done this before.

  Thanks for any help!

  I thought her guy after a few hours of playing with it. I had to pull on the site of HP storage controller driver and group with the ISO (I used experience before VMware: ESXi-Customizer). After having done that, I am sure that AHCI (instead of HP Dynamic Smart Array RAID) has been activated (in the configuration of the BIOS) and disabled by RAID in the HPSSA (intelligent storage administrator). Then, I could see the SSD in the ESXi 5.5.

  Jürgen Vervoort, ESXi 5.5 does not recognize the SSD when I had the active RAID and configured 1 table for each disk (make an effective JBOD). I also tried a single RAID 0 array with two SSDS inside and ESXi does not always detect them. I think that the underlying issue is that the driver is not supported natively by 5.5 ESXi. Right now I'm sure that if I went and configured RAID this would work because the storage controller driver is loaded in ESXi.

  In any case, I hope this will help others with the same issues.

  -GNS

• Is the PowerEdge R610 Compatible DELL VMware ESXi 5.1 update 1 recovery Image?

  Hi all

  Does anyone know if the R610 is compatible with the recovery Image VMware ESXi 5.1 update 1? It is not on the compatibility list, but the r.620 is there. We use two servers in our VMWare environment and I want to upgrade to 5.1 U1.

  Thanks in advance!

  Lee

  Hi Lee,.

  The long wait has its result.

  Seems that it's a typo. Engineering has responded that it is supported.

  Let me know if you encounter other problems.

• Channel Port LACP with VMWare ESXi IP hash Message: % SW_MATM-4-MACFLAP_NOTIF: < MAC > host in the vlan 1 is flapping between port

  Hello

  Currently I have a VMWare ESXi host with 2 network including 6 cards (3 of each) ports are connected to a X 3750.  I configured LACP on the switch and the Port of vDS group road based on IP Hash (802.3ad), my looks of config as follows:-

  src-dst-ip port-channel load-balance

  Interface Port-channel15

  switchport trunk encapsulation dot1q

  switchport mode trunk

  !

  interface GigabitEthernet1/0/15

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/16

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/17

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/18

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/19

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/20

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  Currently I see many MAC beat in the log of the switch.  From my understanding, I expect the MAC address out all ports, because that's what'd ESXi when you use 'route based on the hash of the IP.  I'm worried about the impact this might have on the CPU / switch.

  August 6, 09:42:05.700 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.0939 to host in the vlan 1 is flapping between port gi1/0/16 and article gi1/0/15

  August 6, 09:42:16.479 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.28e4 to host in the vlan 1 is flapping between port gi1/0/20 and 0/article gi1/17

  August 6, 09:42:18.719 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.7f6a to host in the vlan 1 is flapping between port gi1/0/19 and article gi1/0/20

  August 6, 09:42:20.766 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.0939 to host in the vlan 1 is flapping between port gi1/0/16 and article gi1/0/15

  Is it by design, if so can I disable the message?  If this isn't the case, please can you advise where I can check/change the configuration?

  Thank you

  Peter

  It is really gud who... .you mentioned your solution here.

  Can you please mark this question as answered, thatâ so it can help the other guys.

  Concerning

  Please rate if this can help.

• Problem with the start of VMware ESXi 5.0

  I just installed VMware ESXi 5.0 on a new Cisco UCS B200 series blade with two 300 GB hard drives configured in a RAID 1 mirror.  I went through and completed the installation of VMware ESXi 5.0 on this server.  When the installation is complete and the server restarted, he did not initiate the ESXi where I can change the IP address and VLAN.  Instead, I get this text string after the initial boot sequence that is shown in the attachment.  I have a guest who said Shell > do not know why I can not start correctly in ESXi 5.0.  Thank you!  Paul

  Hi Paul,.

  Looks like you boot to the EFI shell. What is the startup policy that you have configured on this server service profile? It should look like the one below.  If there is a problem with the boot order, you should be able to type "EXIT", then enter on the EFI shell to exit the prompt. If your startup is similar to the one below and you still experience this issue, try to downgrade and re - ack the blade.

  Let me know if it helps.

  

• My computer is no longer warn me entry stop when the battery reaches the critical level.

  My computer is no longer warn me entry stop when the battery reaches the critical level. Officially, it shows a warning sign and told me to shot or recharge the battery when it gets to level criticism, but now he can't, but stop just when the battery has reached its critical level. No warning sign more.
  What should I do to get the warning before the pc turns off when the battery is at its critical level.
  My pc is hp laptop mini 110-3100. Start Windows 7.

  Hi Sage180,

  ·         Did you change in the computer before the show?

  Follow these methods.

  Method 1: Run the Troubleshooter of power.

  Method 2: Follow the steps in the article.

  Solutions to common battery problems

  Battery meter: frequently asked questions

  For reference: take care of your laptop battery

• I want to download the update of VMware ESxi 5.5 3B

  But when I sign up for the trial, it puts me update 2 :-(

  What you've recorded for earlier? This happens when you download the other than approved for products product/updates.

  Same error for me, but I downloaded the recording with the new code. I think that you will need to register with the new code.

  VMware KB: How to download VMware products and troubleshooting issues with downloads

  VMware KB: VMware ESXi 5.5, Patch ESXi550-Update03: ESXi 5.5 full update 3

• Impossible to apply license in VMWare ESXi 5.5.0 after the expiration of the evaluation period

  Hello. I recorded and downloaded VMWare ESXi and VSphere about 2 months ago and got it running on our server.

  Today when I logged with VSphere, he said the trial period is over and I need to get a license.

  I connected to VMWare and checked the download link of VSphere with the binaries for 5.5.0 ESXI and VSphere 5.5.0 and told me that I had not registered for the product.

  I signed up for the product and the files were available and I also saw the license key at the top of the download area.

  I copied the license key and went to VSphere, connected to my ESXi and click on Configuration, feature under license and change.

  I Clicked New Assign will authorize and pasted the license key in the box and click ok.

  Then I clicked OK to close the "assign license Dialog", but it came with and error "an error occurred during the license specified key assignment: license is not valid for this product".

  I tried several times and have not been able to apply the license.

  Help, please!

  Check if you used the appropriate license key. Make sure that you do not vcenter licenses for Esxi host. Error message clearly indicates that the license key is not valid for this product...

  Kind regards

  Suresh