VMWare guest auto sleep

Similar Questions

• ISCSI in VMware guest - slow speed

  SAN is a PS4100 with dedicated switches.

  In VMware, I have a Setup vSwitch according to EQ DELL Documentation. The VMKernal properties are:

  • VLAN ID = None (0)
  • vMotion = unchecked
  • Fault tolerance = unchecked Logging
  • Management traffic = unchecked
  • iSCSI Port Binding = Enabled
  • MTU = 9000

  NIC Teaming settings tab:

  • Load balancing = unchecked
  • Failover detection network = unchecked
  • Notify the switches = unchecked
  • Failback = check = No
  • Failover = checked to Override switch control failover

  One in which adapter is set to Active the other place in is not used. This command is enabled for the second VMKernal iSCSI connection.

  The DELL MPIO extension has been added to the VMware host and the connection is configured to use DELL_PSP_EQL_ROUTED for the managed to the ISCSI target paths.

  Managed paths show also active / active status.

  Flow tests with a physical server through a single initiator iSCSI LUNs dedicated show speeds completely saturate the link with 99 MB/s of throughput. All I can manage to inside the guest OS of Server 2012 with NIC vmxnet3, who is also on the SAN is around 30 MB throughput.

  Drops of speed even more during transfer of a network SAN Fibre Channel AX150 hosted VMware guest OS, with an Intel Pro 1000 MT network card, on the one hand of SAN PS4100, it falls to 13 MB/s.

  What I missed, and where should I look to make changes?

  What I should look to increase flow?

  Hello

  There's not much info here to go. I would like to start by making sure that the server is configured by Dell best practices doc.

  en.Community.Dell.com/.../20434601.aspx

  VMware iSCSI configuration will not affect the speed of connection iSCSI comments.   Ideally, comments iSCSI traffic should have its own NIC, separated from the ESXi NIC use because it is the iSCSI traffic.

  Make sure that the VMware tools is installed as well.  Who will ensure that the network driver is optimized.  Run the current version of ESXi is too important.  There was a few KBs on performance with the VMXNET3 adapter problems.   Sometimes change to the E1000 might better work.

• Auto sleep mode will disrupt a current backup procedure?

  Whenever I run a computer backup program, I find that the backup is never completed.  I wonder if the computer auto sleep mode disrupts the ongoing backup process.

  I was getting the same problem and changed the backup parameters does not not not libraries. After I installed Windows 7 I had removed all default libraries and replace them with symbolic links to my NAS drive that is be the same drive as my backup was put in place to save on.

  Once, I removed the libraries from the list of the items to back up, it worked.

  Hope that works for you.

• Auto-Sleep does not work then in the lock screen

  As the title says, I set automatic standby after 30 minutes of idle time of the computer, but it only works when I'm on the desktop, if I'm not connected (lock screen), auto sleep does not work, how can I solve this problem?

  Hello

  A power plan is a collection of hardware and system settings (such as the display, sleep, etc.) who manages the way your PC uses power. Lock screen the console after the deadline option must be added to the advanced power settings.

  Change power management and check.

  Power plans: frequently asked questions.

  http://Windows.Microsoft.com/en-in/Windows/power-plans-FAQ#1TC=Windows-8

• Windows 7 is no longer auto sleep

  My Windows 7 computer won't auto standby on its own. I had the computer since a year and a half and this was not a problem until the last two weeks. If I manually press the sleep button, he falls asleep, but after letting it sit on the computer for the set time, it will not sleep.

  I tried to adjust the power but plan without success. I took leave software I thought I might have caused it but that no longer works.

  I use a wireless keyboard with a mouse on that pad, but I turn it off when not in use is not the question.

  Hello

  I suggest you to refer to the suggestions of COLIENNE V replied on 10 April 2012 and check if that helps.

  http://answers.Microsoft.com/en- US/Windows/Forum/Windows_7-performance/My-PC-Desktop-on-Windows-7-will-not-Go-to-Sleep/a973c317-63ec-4fae-B154-a5c026caece5

  Hope this information helps. Please let us know if you need any other help with Windows in the future. We will be happy to help you.

• Cisco ucs with VMware 5 auto deploy

  Hello

  In our lab, I test with 5 VMware and Cisco UCS. We run UCSM 2.0 (1 m). I am now to test the auto hand deploy. I have auto configuration to deploy in VMware and it works (first of all, I had some problems with DHCP on windows which is solved in version 2.0 of UCSM (q)). vSphere gets deployed to the blade. When the blade (vShpere) wants to connect to vCenter I get an error of vCenter has enough licesing for this action. I loaded a lot of low-income VMware. When I create a virtual machine, it starts perfectly and apears in vCenter.

  I search on the internet for people who have the problem of the simailer, but could not find.

  Some body the same problem our help me?

  Thanks in advance,

  Robin

  Robin,

  This looks more like a VC related question (UCS) platform.  UCS has no effect on the functionality of licenses of the VC.

  If the host does not connect to the CR, how are you VMs to "start perfectly and appear in vCenter?

  Kind regards

  Robert

• VMware Guest works with IPv4 and not IPv6 - ideas everything?

  Well, have a little patience with me. I have a very complicated setup which works perfectly with IPv4, but does not work with IPv6. I hope that one of you superstars can help me to understand how to enable IPv6. Here are the basic configuration:

  
  

  Mac mini:
  

  • Mac mini (end 2012) Mavericks 10.9.5 and VMware Fusion 7.1.0 Server
    • A KDLINKS up one1 account USB 3.0 to Gigabit Ethernet adapter is installed. It is functionally identical to all other brands of USB3/Gigabit Ethernet, which is based on the 6 AX88179 chipset adapter; which is the latest version.
    • (I have another identical USB 3.0 to Gigabit Ethernet adapter, still in the box, do not set, in case this might help the solution.)
  • The most recent 6 Mac driver is installed in the Mac mini, downloaded from ASIX. (The driver on the driver of the KDLINKS Web site is a little older).

  Internet connection:

  • Our Internet connection is a regular cable modem. The cable modem is a simple bridge, Ethernet cable. He gets a public (Internet) IP address on the ISP using DHCP Ethernet interface, as you can imagine.

  VMware Fusion Guest - a firewall device:

  • The VMware Fusion guest is a firewall device. Here's its network configuration:
    • The internal interface is bridged to the Mac mini integrated Ethernet adapter. It has a private IP (10-net). It serves as a one-stop shop for all of your home LAN.
    • The external interface is bridged to the USB/Ethernet adapter. The device of host firewalls Gets the address public Internet IP from the ISP via DHCP.

  Mini Mac Network Configuration:

  • Network Configuration Mac mini (OS X System Preferences network 10.9.5,):
    • The Mac mini integrated Ethernet is configured with a fixed IP on the LAN private address and is configured to use the private IP address of the firewall device of comments as the gateway and DNS server.
    • Adapter USB/Ethernet of the Mac mini is defined as:
      • Configure IPv4: Off
      • Advanced... Configure IPv6: Link-local only
      • The goal is to ensure that the Mac mini can be reached or attacked from the Internet. All Internet traffic should be a device of host firewalls.

  Totally works with IPv4.

  Surprisingly, this all works with IPv4 without any problem whatsoever.

  
  

  IPv6 taken in charge by the provider of Internet services and tested with Time Capsule:
  

  There is no problems with IPv6 when I use an Apple Time Capsule as the firewall / router between the home network and the Internet, using the same cable modem. It is easy to configure, and IPv6 works inside the LAN House and all as well go to the servers on the Internet that support IPv6. Tested, working, as expected.

  I'd do it want to use this device to host VMware Fusion as our firewall router firewalls House for IPv4 and IPv6, the time Capsule not.

  THE PROBLEM:

  The device of host firewalls cannot acquire an IPv6 address of the ISP. He obtains an IPv4 address, but not an IPv6 address.

  THE QUESTION:

  What can I do to make the apparatus of host firewalls acquires an address IPv6, the same way as did the Time Capsule?

  • The Mac mini (host) does not expose its interfaces directly to the Internet.
  • The Mac mini (host) would carry its IPv6 Internet traffic via the comments, the same as its IPv4 Internet traffic firewall application.

  Any suggestions would be greatly appreciated.

  I solved my problem. It was a setting of configuration of the firewall of comments and had nothing to do with VMware Fusion. Here are the details, in case others have the same problem:

  Comments firewall device has been configured as a gateway IPv4, but not as an IPv6 gateway. As a result, the firewall received a single IPv6 address of the ISP. It was a 128, of course.

  Once I enabled the 'IPv6 Default Gateway' setting for the interface external unit of firewall of comments (which translates as the USB3/Ethernet interface to the cable modem) and rebooted the modem cable and firewall, the firewall has asked an IPv6 network block instead (a 64 network). After that, everything worked as expected.

  I know that nobody has answered this detailed query, but I know that a lot of people read it. Thanks for taking a peek. I hope this solution helps others.

• Migrate from VMware Guest Server that contains the database of VIC in the new VMware host

  Hi, I inherited a system running ESX 3.0.1. The CIV is running on a stand-alone server, but the database resides on a guest on one of the VMware hosts. I need to move/migrate the vmware client to another server so I can use it. How can I migrate because if I try I'll lose the connection to the database?

  I can not just to right and migrate because servers have different CPUs. I can first.

  Sorry if this is a newbie question.

  Thanks in advance for any help you can provide.

  do not convert.  This will leave the original intact. Once it comes online and has been validated, you can destroy the old.   In addition, do if offline.

• Oracle DB 11 g OracleEnterpriseLinux 5.4 2 (Windows XP VMware guest operating system)

  Hello
  
  I have Windows XP (host system) running Oracle Enterprise Linux 5.4 as guest operating system in VMWare 2.0. I followed the steps explained in [Tim Hall - Oracle-Base | http://www.oracle-base.com/articles/11g/OracleDB11gR2InstallationOnEnterpriseLinux5.php] and seem to have gotten all the steps correctly and successfully until the final. Then, I also found the following questions. Please let me know if you have encountered these problems and know the solution:
  
  ----------
  H5. Installation of Oracle Enterprise Manager error
  Oracle Enterprise Manager (em) is not installed. Got an error message, then a warning in the installation process asking me to look at the log, but did not find much info about her.
  
  How can I install Oracle Enterprise manager? *
  Status: resolved
  Until_
  I got the bad environment variables. Fixed $ORACLE_HOME. Used emca db rest recreate / create. Get an error or another.
  Solution:_
  removed the SYSMAN account. Some synonyms and issued the following command

  emca -deconfig dbcontrol db

  emca -config dbcontrol db -repos recreate

  The repository is created successfully.
  ----------
  H5. Unrecognized SQLPLUS to other users
  I could access the database by Oracle user, I have to add another user to the OINSTALL group, so that I can access through SQLPLUS? From the SQLPLUS command now that other users are not recognized at all. I need to log in as questions SQLPLUS to access DB and oracle.
  
  How can I access under SQLPLUS as other users? *
  Status: resolved
  Solution:_
  Define oraenv. Run on the shell.
  . oraenv
  and you can run sqlplus and sqlplus command will be honored.
  ---------
  H5. NOT accessible from Windows
  I can't access Windows. I need to use PuTTy and connect as 'oracle' (Unix user) and access it via SQLPLUS. The fact that I am able to connect through the PuTTY for Windows and the possibility to access the Apache Web server (running on port 80) lacked access oracle port 1521 intrigues me.
  
  How can access Windows (using SQLPLUS or Oracle SQL Developer)? *
  Status: resolved
  Solution:_
  earpiece not working. I started it with

  lsnrctl start

  and I'm done. I am now able to connect through SQL Developer.
  ---------
  
  H4. Remarks on the lookout
  Check your environment variables. If you have trouble, it is difficult to correct.
  Read the bloody error logs. They have all the necessary information to set.
  
  Thanks a lot for, phiri. Well enough, he has resolved these questions. Nearly 60 positions, I thought I need to drop the DB and recreate everything, he pulled it like a magic. Happy to have him here. :)
  Thanks in advance.
  
  Published by: guru Perrin on April 14, 2010 12:39

  >
  No errors.

  CREATE THE MGMT_AVAILABILITY FOR MGMT_AVAILABILITY PUBLIC SYNONYM
  *
  ERROR on line 1:

  ORA-00955: name is already used by an existing object

  Going to redo the same Setup again. Drop user, synonym and create. Lets see.
  >

  Please do the following...

  drop public synonym MGMT_AVAILABILITY;
  

  Then

  emca -deconfig dbcontrol db
  emca -config dbcontrol db -repos recreate
  

  Kind regards
  Phiri

• Satellite C75 - A - auto sleep (standby) does not work

  Hello

  My Toshiba SATELLITE C75 - A will not automatically in standby mode (standby) after some time of inactivity.
  Eve works well when I trigger it manually with the start menu and when I do not use the mouse or keyboard for a while, the screen turns off. But neither sleep nor put into hibernation is turned on after the interval set in the energy saving plan.

  When I run
  powercfg with fluo compact
  on the console I get

  "PCI Express Active State Power Management (ASPM) has been disabled due to incompatibility with the hardware on this computer."

  My BIOS is updated.
  I would be really grateful for any advice.

  Hello

  Have you tried to activate the Hibernate mode and standby manually by using the powercfg command?

  Here is a list of possible options regarding the powercfg command:
  [Powercfg command-line options | http://technet.microsoft.com/en-gb/library/cc748940]

  For example with the command * powercfg-h on * turns the hibernation feature on or off.
  You can use also returns a list of devices that support hibernation or sleep

  By the way: what system are you using?

  In addition, you can try to activate or disable the PCIe Link State Power Management in Windows

  Go to control panel-> Power Options-> advanced power plan settings
  Here, scroll down and expand PCI Express and Link State Power Management.

  Currently setting (without battery) or on battery and sector, open the drop-down menu, select Off or ON and click OK.
  If you select No, there is no energy savings, and current runs regardless of which state that the laptop is in. (depending on whether your laptop is plugged or not).
  On battery: Off = PCI Express even will communicate using the power of the battery.
  Plugged in: Off = PCI Express communicates when it is connected as well.

• Windows 7 power options, auto sleep function not working not

  Original title: cannot set option sleep

  Twice the pwer savor sleep option has failed.  I could correct once. on Windows 7 Ultimate but now I can not reset it.  My desktop pc runs every day now when a decision is made on pc.  Why this keep happening?

  Sincerely,

  Frank

  P.S. I have been always a registered user and you refer to my friends.  If not solved this will end the references that I give.

  Hello

  ·         What were the changes made before that happened?

  ·         If it works much earlier?

  I suggest you follow the below link that can help you solve this problem:

  Windows 7 is not going to sleep

  http://support.Microsoft.com/kb/976877

  It will be useful. Let us know for help.

  Regrads,

  Ramata Thakur

• Windows 7 auto sleep function does not

  I put the sleep on the night feature on my desk and the next morning, when I go to use, the computer is turned on.   How can I make the computer sleep?

  Original title: Windows 7 using the Sleep function.

  Hello James,.

  Thanks for posting your query in Microsoft Community.

  1. What have been the recent changes made on the computer prior to the question?
  2. If it works much earlier?

  This problem may occur as a result of changes in power settings.

  You can try the following methods and check if this is useful:

  Method 1: I suggest you to perform troubleshooting of power utility to set the power of your computer settings and check if it works properly.
  Open the troubleshooter of power
  http://Windows.Microsoft.com/en-us/Windows7/open-the-power-Troubleshooter

  Method 2:

  Windows 7 is not going to sleep
  http://support.Microsoft.com/kb/976877

  Additional information:

  Sleep and extended: frequently asked questions See(why doesn't my computer go to standby or hibernate as expected, or why it suddenly wake? )
  http://Windows.Microsoft.com/en-us/Windows7/sleep-and-hibernation-frequently-asked-questions

  I hope this helps. Please let us know the results. Feel free to write us again for any help.

• problem with the connection of devices to VMware guests

  I have a hpe 130f.  When I power on a virtual machine, I get the message «failed to initialize the controller usb in VMware» I did everything according to the VMware kb. I've never had this problem with my old computer, so I suspect it's a driver causing the problem.
  

  The fixed. I discovered that the ATI catalyst install Manager has been installed which contains an amd usb filter driver. I just uninstalled, rebooted and now VMware can communicate with my usb devices.  I don't know why, who was installed by hp as my system has a nvidia card, although I think there may be an ati integrated graphics card.

• VMWare Server Auto walk stop VM

  The documentation states that you must activate this option when installing VMServer 2. I installed 3 times now looking for AN option in addition to the locations on the disk and can't find anything. In the management console, there are options for start/stop with the host, however, virtual machines any "off" to start. The documentation says "Note to allow the virtual machine to be started and stopped on a Windows host, you must also select Allow virtual machines to start and stop automatically with the system during the installation of VMware Server.»

  Can someone tell me the buttons to activate this option?

  Thank you

  Bill

  If you select a computer and then click "Move up", it should become "activated" when it hits the sections 'Specified order' or 'Any order' and you can then change the settings to set the start or stop (as long as you have administrator privileges). Please see the attached screenshots.

  A witch hunt to start during the startup of the host if you have virtual machines on a data store that is not available at startup, for example sometimes if it's on an external or drive network rather than local.

  --

  If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.

• Want to 700 don't put it to sleep sleep/auto-manual OK

  My PC, w8.1, goes into sleep OK with manual operation mode, but will not auto-sleep. The screen switches mode "sleep" at the scheduled time, but auto-sleep never happens. I configured in mode auto-sleep at a time. Any ideas?

  Hi tizzy,

  Sleep problems are one of the problems most upsetting user must face. There are too many variables involved.

  You can find a solution by referring to this guide.

  Hope this helps you.

  Jaco

  I'm not an employee of ch *.

  "" "" Please give a "Bravo, Thumbs Up" If the notice is relevant or "accept as Solution" to help other users of the forum having a similar problem.

  HP products:
  810-150se office
  17 t - j000 Notebook
  H8 1380t CTO Desktop
  560z Desktop