Vostro 410 - update motherboard

Similar Questions

• Vostro 410 does not illuminate

  I have a computer Dell Vostro 410. I accidentally hit the power button on the surge protector the other day and he died, which means he will start.

  This happened a few years back a couple times, but worked once I unplugged all USB keys and other sons and waited for about an hour. It went Tuesday and still nothing.

  When I plug the power cord in, the green light in the back turns, but that's all. I opened it upward and the dust is really gross, so I'll buy a can of compressed air and blow today, but I don't see how that could be the cause that it doesn't turn.

  I also found a few caps inside which are not connected to anything, but perhaps that they need not be?

  I tried to take the two RAM sticks and then putting back in which I will again because it took me 30 minutes just to get them back in.

  It is running XP.

  Please help... :(

  Thank you!

  fan1bsb97

  Bev, there is no error message or beeps that the computer doesn't turn on at all. There is no led power light - I think, it was blue - now, there is nothing. The only light is solid green light under the power cord and the yellow light inside the computer.

  fan1bsb97

  First try to connect the computer directly to an outlet without the surge protector, to see if that makes a difference.

  No difference, then replace the power supply a "known" PSU to work again to see if that makes a difference, as an it isn't required to test the motherboard etc. See page 32 of the maintenance manual.

  More generic standard ATX power supplies, with a 24-pin or 20 + power connector 4 - pin main motherboard, with or without the on/off switch, would be compatible with the Vostro 410.

  You should be able to buy a compatible power supply either a local computer or online store.

  Note: For the Vostro 410 mini-tower with six SATA power connectors power is required.

  Bev.

• Video drivers for Vostro 410 embedded video

  The separate PCI-e video that came with my Vostro 410 just died.  However, the integrated VGA video works (after I removed the card).

  However, I find no video drivers for the onboard video.  Can someone tell me please to them?

  Thank you.

  GraydonJ

  The separate PCI-e video that came with my Vostro 410 just died.  However, the integrated VGA video works (after I removed the card).

  However, I find no video drivers for the onboard video.  Can someone tell me please to them?

  Thank you.

  have you looked at these drivers HERE.

• Network with the new Vostro 410 problem

  I just got a new Dell Vostro 410, running XP Pro, to replace a 2400 Dimension 5 - years, which had been connected to my DSL ATT line via ethernet through a 2Wire 1800 HG. My laptop and two other offices (which is the replaced 2400) is connected through wireless cards or adapters. Three wireless computers came online immediately, get internet access and work very well.  All computers are running XP.

  The problem is that I can't access the Vostro or its USB printers through computers connected wirelessly that could print previously via the cable 2400. They do not appear and are accessible on the Vostro and the Vostro appears in the Working Group, but not belong to network on the other three.

  I tried to redo the Network Wizard, but I'm having no luck at all.

  Any suggestions would be greatly appreciated.

  Ron

  Message edited by RS2 on 09/23/2008 11:55
  
  

• Ignition intermittent problem with Vostro 410

  Last week, I had a problem with my Vostro 410 minitower.

  When power is applied to the area of the Green LED on the back of the PSU and the amber LED on the main Board, both light up normally.

  By pressing the power button sometimes starts the system as usual, with the fixed blue light button, but more often all that happens is the button flashes amber and then nothing, except a slight noise as if a fan is about to begin.

  Remove the power and try again sometimes works, as leaving the box for a while after the first power of the application. The other thing that always work sends a message of WakeOnLAN since another device on my network. the PC starts and runs exactly as if the power button worked.

  Once started the PC boots and works perfectly as before.

  I tested the power supply and they are all to a few percent of their nominal values. Unplug the connector ATX 24 pin as well as a short circuit of the Green wire to Earth begins the PSU.

  I tried to change the on-board battery, but the problem is exactly the same with a new or partially charged battery or nothing at all.

  Can someone please suggest a cause and cure?

  

• Update motherboard Vostro 260

  Hello

  I have motherboard Vostro 260

  Can I upgrade my processor i3-2120 3470 i5 or i5-3570?

  kamel20dz

  Hello

  I have motherboard Vostro 260

  Can I upgrade my processor i3-2120 3470 i5 or i5-3570?

  kamel20dz

  Already answered in your other messages here:

  http://en.community.Dell.com/support-forums/desktop/f/3514/p/19497687/20946462#20946462

  Bev.

• Satellite A200 - update motherboard

  Hi, I'd like to update my graphics card, but I have read that I have to upgrade my motherboard to do this. Is this true? I want to improve to be able to play 3D games. Motherboard should I go to? I have a Satellite A200.

  I believe that this document can give you an answer to your question
  http://APS2.toshiba-tro.de/KB0/FAQ7A01ZW0007R01.htm

  The card mother and video card are designed, you cannot upgrade the video card in a series later.

• UPDATE MOTHERBOARD

  I want to update my card mother p6610f so that I can install a processor AMD 8350 what changes are what I should do and what motherboards do you suggest?

  Here are the specifications of your HP Pavilion p6610f desktop computer and its card mother Μatx-RS880-Alvorix (Alvorix). Based on this information, you will need to buy a hat from motherboard AM3 + supports the processor AMD FX-8350, install a new power supply and buy a new copy of Windows 7 Home Premium 64-bit. Your Windows installation factory will become non-genuine and your HP recovery disks will stop working. I really do not recommended that you try to upgrade your p6610f by going down this road.

  Please send Bravo

• Holly AAHD2-HY Pegatron Bios Update motherboard

  Is someone can you please tell me if there is an update available for the motherboard bios above.  I have upgraded to windows Pro 8.1 with Media Center.  My system information is below.

  Name of the Microsoft Windows OS 8.1 Pro with Media Center
  Version 6.3.9600 Build 9600
  Another Description of the OS is not available
  Manufacturer of operating system Microsoft Corporation
  Name of the system
  System manufacturer Hewlett-Packard
  P6-2100 model system
  System Type x 64-based PC
  SKU QW795AA #ABA system
  A4-3420 APU AMD processor with 2 logical processors, 2 Lossnay, 2800 Mhz, graphics HD Radeon (TM)
  BIOS version / Date FRIEND 7.15, 16/12/2011
  SMBIOS Version 2.7
  Embedded Controller Version 255.255
  UEFI BIOS mode
  Baseboard manufacturer PEGATRON CORPORATION
  Model baseboard is not available
  Name of plinth base
  Role of platform office
  State of secure boot not supported
  PCR7 Configuration binding is not Possible
  Windows directory C:\Windows
  System directory C:\Windows\system32
  Boot Device \Device\HarddiskVolume2
  The local United States
  Hardware Abstraction Layer Version = "6.3.9600.17196".
  Eastern Daylight Time zone
  Physical memory (RAM) installed 8.00 GB
  7,49 GB total physical memory
  4.49 GB available physical memory
  15.0 GB total virtual memory
  12.0 GB available virtual memory
  Page file space GB 7.50
  Paging file C:\pagefile.sys
  Hyper-V - VM monitor Mode Extensions Yes
  Hyper-V - second level address translation Extensions Yes
  Hyper-V - virtualization enabled in Firmware No.
  Hyper-V - data execution Protection Yes

  Hello MattNC79,

  I understand that you are looking for an update of the BIOS of your desktop PC HP Pavilion p6-2100 using the card mother AAHD2-HY (Holly). Unfortunately, I couldn't locate an update of the BIOS for that motherboard at this time.

  I hope that I have answered your question to your satisfaction. Thanks for posting on the HP Forums. Have a great day!

• bios update motherboard M2N68-(Narra5)

  need a update in order to run the hard drives of 4 t. 6.01 running 29/09/2010.

  You don't give much info system, but here are the basic system requirements, you must use a plu 2.2 TB HARD drive

  Need a 64-bit operating system
  * Motherboard that supports UEFI [successor to the BIOS]
  * Support for GPT partitions [instead of MBR]

  Your system meets these requirements?

  If you found my answer helpful please say thank you by clicking the s cursor Up icon. Thank you!

• Update motherboard on a DC7700 Sff

  Hello.

  First of all, sorry if this is in the wrong place. IM new to the forum stuff. Also, sorry if this has already been answered.

  So I'm wanting to upgrade my dc7700 sff as much as possible. Up yet, I upgraded the GPU, RAM disk and windows, but I would like to upgrade the motherboard. From what people have told me, it is impossible to update the motherboard, but I would like some other opinions before I spend money I havnt really on a new PC.

  Here is a complete list of my specs (on the top of my head):

  160 GB Sata HARD drive

  3 GB RAM

  ATI Radeon X 1300 Pro GPU

  Intel (R) Core (TM) 2 CPU 6400 @ 2.13 GHz 2.13 GHz

  If you need more info please let me know and thanks for the help!

  Hello:

  If you want another opinion, then I agree with everyone who said that we can't do.

  Dc7800 SFF dc7900 SFF and the Elite SFF 8000-8300 have a redesigned cards mothers and where, so that they do not coincide in your model.

  And if you are referring to a classic motherboard you can buy from a manufacturer of motherboard (ASUS, Gigabyte, etc.), which can be done either.

• Vostro 410 does not start

  I have a dell vostro. Worked fine for the last years, except now.

  Empty computer screen so my son off on your computer with the power button, now when you turn on the computer, the fan run continuously but not start or give error beeps.

  Button on the front is lit in blue.

  Checked the power supply, iy is ok and checked the memory, they are ok.

  any help would be

  242digital

  Try the following, if you are comfortable working around computers:

  Note: The only 100% POWER supply test method, is to install a known working power.

  Unplug the power cord, hold the power button in for about 15-20 seconds, open the case, disconnect the power connector 24-pin motherboard and jumping the Green wire to one of the black wires, plug in the power cord and the power of the system, if food and case fans and disk hard drive performance then the power supply should be good.

  Note: Do not remove the wires from the plug, use a small piece of wire or a paper clip as a rider.

  Excerpt from power supply, again, unplug the power cord, hold power in a few seconds to discharge residual power, reconnect the connector 24 pin to the motherboard.

  Remove all the computer PCI cards, remove the video card [as appropriate], disconnect all devices, except the monitor, mouse and keyboard and unplug cable power & data of all readers.

  Reconnect the power cord and power the system on, see if you get a different indication of the LED on the power button / stop, or 'beeps '.

  No difference, remove the system memory and try again.

  Still shows no signs of life while looking at a motherboard replacement & maybe a processor.

  Note: The processor rarely fails and the only method I know to check a processor, is to install a compatible working PC, or use a known job processing.

  Bev.

• Update motherboard on Dimension E521

  I want to improve my current AMD Athlon CPU with an AMD Phenom, but my current motherboard is not compatible with it. What motherboards can I get compatible with AMD Phenom (socket AM2 +) and which fits inside the case? I guess that my current memory sticks is not compatible with the new processor. Thank you.

  Message edited by dong0liu on 06/16/2008 12:54
  
  

• Update motherboard, processor and graphics card.

  Hi, I have a few questions. If I decide to upgrade my motherboard, processor and Grahpics card, do I need to reinstall windows? And if so, my product key will work? I am a student and downloaded the free download of Windows 7 Pro for more information if this is useful.
  It is said that my product ID type is 5-retail, it is authorized and says I have a meter to rearm windows 3.
  The motherboard I am upgrade is also from the same company, Asus.

  You will need to reinstall and use the phone activation:

  How to activate Windows 7 manually (activate by phone)
   
  1) click Start and in the search for box type: slui.exe 4
   
  (2) press the ENTER"" key.
   
  (3) select your "country" in the list.
   
  (4) choose the option "activate phone".
   
  (5) stay on the phone (do not select/press all options) and wait for a person to help you with the activation.
   
  (6) explain your problem clearly to the support person.
   
  http://support.Microsoft.com/kb/950929/en-us

• Updated motherboard, switching to home premium oem in professional detail.

  I have a copy retail Windows 7 Professional which has been activated on another computer I'm disassembly and no longer go to the for use.  Can I use this copy of windows in my new computer that is running windows 7 Home premium oem (just installed new motherboard and it continues to ask for activation) without any problems?  If possible I'll have to do a clean install or can I use any time upgrade?

  I'll give my younger brother my old computer should be able to have rights on the oem license, this hypothesis is correct?  What I read in the other questions and answers the oem cd key is locked to the computer, and since I'm going to give him the greater part of the original computer (less memory and hard drive) it should work right?

  The computer with the version of Windows OEM must keep the OEM version.

  You can install Windows 7 Pro on the new computer as a clean install (the key does not work as an anytime upgrade). Must be a 'Full' product or you need an earlier version of Windows to use an "Upgrade" version

  Windows 7 upgrade paths: http://technet.microsoft.com/en-us/library/dd772579%28v=ws.10%29.aspx

  J W Stuart: http://www.pagestart.com