VPN authentication
I have 2 tunnel-groups:
tunnel-group test type ipsec-ra
tunnel-group test general attributes
address pool VPN_Pool
LOCAL authority-server-group
authorization-server-group (inside) LOCAL
authorization-server-group (outside LOCAL)
Group Policy - by default-test
authorization required
IPSec-attributes of tunnel-group test
pre-shared-key *.
and
tunnel-group users type ipsec-ra
attributes global-tunnel-group users
address pool VPN_Pool
Users by default-group-policy
tunnel-group users ipsec-attributes
pre-shared-key *.
USAERS is access vpn production group, it uses the LOCAL authentication database and the most important for that matter - it works well.
test as you can guess, is a group of tests that has been created in the time that I have configured ASA5505 for the first time. He also works.
both groups use the same database LACAL, BUT as you can see it the users group has nothing to show.
I need to change the authentication from the LOCAL RADIUS (I tested this ASA and works very well). I want to start by testing the test group and if it's all good - apply to the users group.
How can I do?
How can I make primary source with fall to the LOCAL RADIUS authentication if RADIUS is down?
You'd go into your settings of tunnel group and change the settings as a result like this:
tunnel-group test general attributes
Group of LOCAL authentication server
This will cause the tunnel group first use the RADIUS and the Local if radishes fails. Note You can remove the part of the authorization of your configuration.
Tags: Cisco Security
Similar Questions
-
VPN authentication and wireless through ACS 5.4
Hello,
I am in the process of migrating from ACS 4.1.1.23 to ACS 5.4. I have migrated our users and Network Device Groups and configured external Identity stores like AD and RSA. I want to authenticate our Wireless users with AD and VPN users through RSA. I am unable to create policies to get this UP and working. I need help in this regarding the policy creation.
As I am new to the ACS 5.4 any help with the step by step configuration of the WLAN and VPN
authentication will be appreciated.Thanks in advance.
Regards,
Anand
This is possible by creating access to two Services: one that authenticates with AD and the other against RSA.
Then have need develop a selection of Service policy that will result in one of these two services. One possibility could be NAS-Port-Type in the RADIUS dictionary which should be 'Wireless - IEEE 802.11.
-
SSL VPN authentication using the ad group
Hi all
I tried to restrict users to authenticate to the SSL VPN using an ad server. I have install the AAA server with the IP address of the AD server and attributed to the connection profile as well; However, I see that any user who is a member of a group in AD is able to authenticate.
I want to only users who belong to the group "VPN users" get authenticated while everyone and all those who have credentials of the AD and not even a part of the 'VPN users' group is making authenticated.
Can someone advice how I can make the ASA authenticate users based on ad groups? I use the ASDM to configure my VPN RA.
Thanks in advance!
Kind regards
Riou
Hey riri,.
Try to use DAP to restrict access to users who belong to a specific ad group:
https://supportforums.Cisco.com/document/7691/ASA-8X-dynamic-access-poli...
Use the AAA attribute "LDAP .member of" to allow access to the users belonging to a specific group and deny access to other users.
concerning
Eric
-
IPSec VPN authentication problem against AD by RADIUS/ISA
As background, I have a VPN IPSec authentication against the local database upward and running with access to my internal network and work with zero issues.
So I would move offshore to the local database authentication and boince it is outside my ad. I am running 2003 server so I configure ISA Server RADIUS and think I have it properly configured. It is registered in the AD, I added my asa as a customer radius, customized remote access and connection request policies.
The test of authentication in the ASDM he succeeds with all users who need.
During the test through my client vpn on a remote computer, I get the connection terminated by a peer, no reason given.
It is said of the event on the domain controller logs
-l' user domain - user % name % has had access.
directly after this, there is an entry
-VPN-RADIUS-GP is denied access
where VPN-RADIUS-GP is the name of the tunnel group policy in my ASA.
Ive tried a lot of literature and a few forums and have not yet find any explanation as to why this would happen as username trying to authenticate to the ISA
Anyone have any ideas?
Thank you
Mac
group-policy VPN-Radius-GP external server-group VPN_Radius_Auth password aaaaaaaaaaaaaaaaaaaaaa
It is a group-foreign policy, by definition, that it is defined on the AAA server group policy, so the ASA sends a radius access request to retrieve the attributes of group policy.
See for example http://www.cisco.com/en/US/docs/security/asa/asa72/configuration/guide/vpngrp.html#wp1133706
If this isn't what you want, then just remove the group policy and use internal (as the "q101 VPN GP" you).
HTH
Herbert
-
Client VPN authentication question
Hi friends,
I recently started a new company, where the Cisco VPN Client is used by all remote Windows users. I'm not familiar with the customer. I see by our remote access policy that clients authenticate using PAP. This immediately caught my concern.
My question is if this poses a threat to security? Even if the authentication is not encrypted, it is always the case in a 3DES IPSec tunnel, right? What is the best practice regarding using the VPN client and authentication?
Thanks in advance!
Equipment:
Cisco VPN Client v5 (latest version) on Windows XP SP3
Microsoft IAS (RADIUS) on W2K3 Server R2 x 64
Router Cisco 3825
IOS 12.4.24T Adv IP Services
If I understand your customer VPN ends on 3825 router. the customer gets the name of username/password prompt after than phase 1 so it may not be clear.
I hope this helps
concerning
-Syed
-
Recommendations for VPN authentication
So, now that Cisco has helped me get the vpn works on my ASA 5525-X I need to use an active administrator for the authentication/grouping of customers for several profiles in anyconnect.
My question is what is the simpler and more effective way of setting this up. I have a R2 2012 NAP server that is used to authenticate the AD users for access to the switches. But should I use that for ASA as well or can I use AD directly to the ASA?
A reminder to those who have not seen my posts, I'm very new to the ASA and the need to get this up and running quickly... Any help/suggestions would be greatly appreciated.
Thank you
Stacey
Hi Stacey,
You can use the Windows Server direct to the ASA, it uses the LDAP protocol. You will need to implement the ASA like this:
AAA-Server LDAP-SRV protocol ldap
AAA-Server LDAP-SRV (inside) host XXXXXXXXX--> IP address of the server
LDAP-base-dn DC = vpn, DC = also, DC = com--> where users are stored
LDAP-connection-dn CN = ASA-LDAP-user, CN = Users, DC = vpn, DC = also, DC = com--> the entire AD tree.
LDAP-login-password *--> the administrator password
LDAP-naming-attribute sAMAccountName
LDAP-scope subtree
microsoft server typeNow, you need to get the login DN: and the base dn. Now on the ad, you need to create several user groups and divide the users for different levels of authorization as: salespeople, employees...
You can test the authentication by using this command:
test the aaa server for authentication LDAP_SRV host XXXXXX username: password XXXXX: XXXX
and then see if it fails, then you can solve the problem
You can then configure the mapping of LDAP attributes to MAP a group of users on the server of advertising to a group policy on the SAA.
http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...
I would like to know how it works!
Please don't forget to rate and score as correct the helpful post!
David Castro,
Kind regards
-
SSL VPN authentication using different sequences of identity Sources
Morning,
At the moment we have SSL VPN configuration passing security to GBA. This is accomplished by using strong authentication. GBA the
Sequence identity Sources is WBS then AD.
We want to implement on the same firewall a few users select proper respect by AD authentication, they will have a group name different tunnel connecting etc.
GBA im not sure how I would setup two sequences of Sources Identidy therefor using the same Service selection rule. At the moment I have if RAY and IP is XXX then political use of XXX
We are currently installed ISE so in the not to distant future is ACS can not do this can ISE?
If it's confusing that I can extend were nesscessary
Thank youS
Hello
I don't know how it looked like GBA but on its flexible ISE
If the rule is simple
If the RADIUS request is device ASA type formed then check the tunnel-group-name attribute (146) and will benefit from its interventions to the string value choose LOCAL or AD store.
hope this helps
concerning
-
I see options to authenticate users VPN on Radius, Ganymede +, local or using a VPN group. Is - this from there anyway to authenticate on a NT domain, Active Directory by Microsoft or Novell eDirectory directory service?
Cannot find details in the configuration guide.
Thank you
Greg
Hello Greg,.
Thanks for your question. In fact, PIX is not built in API unlike VPN 3 K to send the authentication request directly to the devices you mentioned. PIX has the RADIUS / Ganymede + API and that is why its need to use an AAA server that supported Radius/Ganymede. AAA Cisco Secure Server can be integrated with all deviecs you mentioned. You can point your PIX to the Cisco Secure AAA server and he will forward the application to the database you mentioned in your post.
I hope this helps. Kind regards
Renault
-
LOCAL + RSA VPN authentication?
Hi... we have a customer using an ASA 5520 8.2 (2) for VPN (webvpn) connections. Currently, they use the user/pass configured locally for authentication (it's a default, there is no explicit LOCAL configuration).
They would use their RSA security device, but not for all users at once. Is it possible to use the local database and RSA as points of authentication, i.e. If there is no configured local user name, try the RSA (or vice versa)?
Thank you
Jim
The ASA can do that natively the emergency authentication being quite limited on the SAA. Two possibilities are there to solve this:
(1) use an external server which can chain these authentication stores (ACS or ISE may be used). But it is a rather expensive solution.
(2) build more tunnel-groups with different authentication settings and ask your users to use a particular.Sent by Cisco Support technique iPad App
-
SSL VPN authentication using RADIUS
I am running version ASA 8.4 (1) and anyconnect version 3.0.1047. My SSL VPN works great, but I encountered a problem with a user. his story did not work, and each time users had this message ""VPN server could not parse request '. "
I found the problem after getting user information, which means that his user name and password. Had a password '&' as one of the special characters. When we change to something that isn't that it works very well.
We use the NPS as RADIUS server. but when I run a test within the CLI, it works fine, only when anyconnect requests to authenticate, he fails.
Someone at - it had the similar problem?
Thank you
Marcin,
This could a re-appearance of:
Would you be able to test the workaround?
Marcin
EDIT
Looks like this:
-
Authentication of ISE 1.3 VPN with Email address instead of the username
Hello
I would like to set up a VPN authentication against LDAP Microsoft Directory.
The user must between its e-mail address that is stored in the mail attribute LDAP MSFT. How can I configure ISE to watch in the mail of the attribute to find a user rather than the user name?
Thanks in advance
Alex
You can use the "custom" setting schema in ISE under the external identity/LDAP and change the object attribute to "mail" instead of "samAccountName", which is the normal attribute ISE uses to search for users in the LDAP structure. You can then chech if it works, by going to the menu attributes and search for an e-mail address that you know should be there.
-
ACS 5.0 with authentication VPN
Hello
If you would be grateful if someone could guide me how to configure the ACS5.0 radius for authentication of remote access VPN.
And how could I implement the Pools of IP for VPN users.
Best regards
Lunedor
Hello
An IP address assignment is not possible the GBA. However, you can configure the simple vpn authentication.
GBA:
access policies> default network address> identity(select internal users or if its AD then select AD) > authorization > click on customize > move the desired condition>
for example> device ip address> put in the ip address of ASA(vpn device)> authorization profile> permit access.so it will be>
access policy> default network access> identity(internal users or AD)> authorization > create rule> device ip=1.1.1.1 > authorization profile=permit access
You can follow the link for common scenarios below:
Concerning
Bellefroid
Note the useful messages
-
ISA500 site by site ipsec VPN with Cisco IGR
Hello
I tried a VPN site by site work with Openswan and Cisco 2821 router configuration an Ipsec tunnel to site by site with Cisco 2821 and ISA550.
But without success.
my config for openswan, just FYI, maybe not importand for this problem
installation of config
protostack = netkey
nat_traversal = yes
virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%4:!$RIGHT_SUBNET
nhelpers = 0
Conn rz1
IKEv2 = no
type = tunnel
left = % all
leftsubnet=192.168.5.0/24
right =.
rightsourceip = 192.168.1.2
rightsubnet=192.168.1.0/24
Keylife 28800 = s
ikelifetime 28800 = s
keyingtries = 3
AUTH = esp
ESP = aes128-sha1
KeyExchange = ike
authby secret =
start = auto
IKE = aes128-sha1; modp1536
dpdaction = redΘmarrer
dpddelay = 30
dpdtimeout = 60
PFS = No.
aggrmode = no
Config Cisco 2821 for dynamic dialin:
crypto ISAKMP policy 1
BA aes
sha hash
preshared authentication
Group 5
lifetime 28800
!
card crypto CMAP_1 1-isakmp dynamic ipsec DYNMAP_1
!
access-list 102 permit ip 192.168.1.0 0.0.0.255 192.168.5.0 0.0.0.255
!
Crypto ipsec transform-set ESP-AES-SHA1 esp - aes esp-sha-hmac
crypto dynamic-map DYNMAP_1 1
game of transformation-ESP-AES-SHA1
match address 102
!
ISAKMP crypto key
address 0.0.0.0 0.0.0.0 ISAKMP crypto keepalive 30 periodicals
!
life crypto ipsec security association seconds 28800
!
interface GigabitEthernet0/0.4002
card crypto CMAP_1
!
I tried ISA550 a config with the same constelations, but without suggesting.
Anyone has the same problem?
And had anyone has a tip for me, or has someone expirense with a site-by-site with ISA550 and Cisco 2821 ipsec tunnel?
I can successfully establish a tunnel between openswan linux server and the isa550.
Patrick,
as you can see on newspapers, the software behind ISA is also OpenSWAN
I have a facility with a 892 SRI running which should be the same as your 29erxx.
Use your IOS Config dynmap, penny, you are on the average nomad. If you don't have any RW customer you shoul go on IOS "No.-xauth" after the isakmp encryption key.
Here is my setup, with roardwarrior AND 2, site 2 site.
session of crypto consignment
logging crypto ezvpn
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
lifetime 28800
!
crypto ISAKMP policy 2
BA 3des
md5 hash
preshared authentication
Group 2
lifetime 28800
!
crypto ISAKMP policy 3
BA 3des
preshared authentication
Group 2
!
crypto ISAKMP policy 4
BA 3des
md5 hash
preshared authentication
Group 2
!
crypto ISAKMP policy 5
BA 3des
preshared authentication
Group 2
life 7200
ISAKMP crypto address XXXX XXXXX No.-xauth key
XXXX XXXX No.-xauth address isakmp encryption key
!
ISAKMP crypto client configuration group by default
key XXXX
DNS XXXX
default pool
ACL easyvpn_client_routes
PFS
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac FEAT
!
dynamic-map crypto VPN 20
game of transformation-FEAT
market arriere-route
!
!
card crypto client VPN authentication list by default
card crypto VPN isakmp authorization list by default
crypto map VPN client configuration address respond
10 VPN ipsec-isakmp crypto map
Description of VPN - 1
defined peer XXX
game of transformation-FEAT
match the address internal_networks_ipsec
11 VPN ipsec-isakmp crypto map
VPN-2 description
defined peer XXX
game of transformation-FEAT
PFS group2 Set
match the address internal_networks_ipsec2
card crypto 20-isakmp dynamic VPN ipsec VPN
!
!
Michael
Please note all useful posts
-
Replication failover PIX VPN (CEP) certificate
Hello
Had a pair of PIX 525 on 6.3 (4) version running in active/failover mode, I recently configured VPN authenticated by certificates, which involved the use of PRACTICE in order to get the certificate to the PIX. Certificates have been imported for the PIX from a snap-in with the software component CEP Protocol Windows CA server by following the instructions described here: http://www.ciscosystems.com/en/US/docs/security/pix/pix63/configuration/guide/sit2site.html#wp1007263 .
It all works very well, the configuration has been saved, certificates registered cases using "ca save all", everything works well except the certificates that have been imported have not been replicated for the PIX failover - the command 'Show the ca certificate', shows not all certs.
Private keys show 'sh ca mypubkey rsa' are the same on both devices.
I'm not able to find any documentation about how certificates must be replicated on the PIX failover, and it is not possible to write certificates again on the PIX failover using the commands they were initially imported by:
PIX - fw # conf t
WARNING *.
Configuration of replication is NOT performed the unit from standby to Active unit.
Configurations are no longer synchronized.PIX - FW (config) auth ca ca
WARNING *.
Configuration of replication is NOT performed the unit from standby to Active unit.
Configurations are no longer synchronized.Everyone knows a similar issue or how to get the PIX failover with the new ca certificates?
Kind regards
Sarunas
Hello Sarunas
PIX 6 indeed do not synchronize keys and certificates automatically.
However, you should be able to do this first, forcing a failover (i.e. secondary image make it active), then register (now active) high school with the certification authority.
HTH
Herbert
-
Setting up the VPN for ACS5.5 group
I'm trying a group in the ACS5.5 which allows users to connect. I created a network called ASA - VPN group and he put in ray and Ganymede. The ACS is linked to AD. I am lost on what to do next as rules of extreme ass or attributes. I do business with ISE before but not of GBA.
Take a look at the following link as it describes a step-by-step process:
Let us know if you still have any questions.
Thank you for evaluating useful messages!
Maybe you are looking for
-
I'm a software tester for an internal application to my company. version 10.0.2 is not cmopatible with a few controls within our software. I need the download v9.0.1 whatever works with the controls. Where can I get?
-
When you use "Scan to email" a window pops up "unable to find mail account" Although there are accounts of e-mail on my pc. the printer is connected to my pc with the usb cable and installed for use with cable and wireless use.
-
More video RAM on my Satellite A30
Hi, how can I share more video ram on my A30, is now 32 MB?
-
How to enter the phase of a signal and get back his corresponding voltage?
-
scanning and emailing multidocument
I use a s 6830 model HP laptop with Windows Vista op system Business and a model HP 6210 all-in-one printer, Fax, Scanner, copier. I'm having a problem scanning and e-mailing several pages of a document. Some of my recipients receive all pages OK but