VPN Cisco IPSEC - ISAKMP id_connexion

Hi Experts,

We have a site to site VPN IPSEC between a router Cisco 1801 and 800F fortigate firewall.

Works VPN, but a quesiton that I are just Conn Isakmp id changes very frequently and I wanted to just make sure that I understood why.

When I run the isakmp crypto to show its command, I get the following:

IPv4 Crypto ISAKMP Security Association
DST CBC conn-State id
1.2.3.4 5.6.7.8 QM_IDLE 2455 ACTIVE
1.2.3.4 5.6.7.8 2454 MM_NO_STATE ACTIVE (deleted)

In the time it took me to write this, it has changed:

IPv4 Crypto ISAKMP Security Association
DST CBC conn-State id
1.2.3.4 5.6.7.8 QM_IDLE 2457 ACTIVE
1.2.3.4 5.6.7.8 2456 MM_NO_STATE ACTIVE (deleted)
1.2.3.4 5.6.7.8 2455 MM_NO_STATE ACTIVE (deleted)

So, for me it looks like the phase ISKAMP 1 re-lance his SA very frequently. I put the ISAKMP policy as follows:


World IKE policy
Priority protection Suite 10
encryption algorithm: three key triple a
hash algorithm: Message Digest 5
authentication method: pre-shared Key
Diffie-Hellman group: #5 (1536 bit)
lifetime: 86400 seconds, no volume lim
it

Therefore, should - that means that the Phase 1 SA should only re-iniate 86400 seconds?

Any information would be appreciated,

Thank you very much

Jonathan

Hello

It seems you have DPD (isakmp crypto KeepAlive) configured on your router.  This determines the accessibility of the other VPN endpoint, and we are not to understand thanks for the packages "R U THERE" (due to the problem of the DOI) that we send them, ISAKMP marks the tunnel as death and tears down.

Traffic on the tunnel seems so the tunnels, and then DPD expires them again.

Flip through your configuration for the "keepalive" order and if it is set for periodicals, set the KeepAlive for 'on demand' (which should be the default) so that we only send DPD when we are unable to determine whether the tunnel is alive because no traffic is coming on it.

This doc link is old, but he describes the functionality well enough:

http://www.Cisco.com/en/us/docs/iOS/12_3t/12_3t7/feature/guide/gtdpmo.html

-Jason

Tags: Cisco Security

Similar Questions

  • Cisco VPN Client and Windows XP VPN Client IPSec to ASA

    I configured ASA for IPSec VPN via Cisco VPN Client and XP VPN client communications. I can connect successfully with Cisco VPN Client, but I get an error when connecting with the XP client. Debugging said "misconfigured groups and transport/tunneling mode" I know, they use different methods of transport and tunneling, and I think that I have configured both. Take a look at the config.

    PS a funny thing - when I connect with client VPN in Windows Server 2003, I have no error. The only difference is that client XP is behind an ADSL router and client server is directly connected to the Internet on one of its public IP of interfaces. NAT in the case of XP can cause problems?

    Config is:

    !

    interface GigabitEthernet0/2.30

    Description remote access

    VLAN 30

    nameif remote access

    security-level 0

    IP 85.*. *. 1 255.255.255.0

    !

    access-list 110 scope ip allow a whole

    NAT list extended access permit tcp any host 10.254.17.10 eq ssh

    NAT list extended access permit tcp any host 10.254.17.26 eq ssh

    access-list extended ip allowed any one sheep

    access list nat-ganja extended permit tcp any host 10.254.17.18 eq ssh

    sheep-vpn access-list extended permits all ip 192.168.121.0 255.255.255.0

    tunnel of splitting allowed access list standard 192.168.121.0 255.255.255.0

    flow-export destination inside-Bct 192.168.1.27 9996

    IP local pool raccess 192.168.121.60 - 192.168.121.120 mask 255.255.255.0

    ARP timeout 14400

    global (outside-Baku) 1 interface

    global (outside-Ganja) interface 2

    NAT (inside-Bct) 0 access-list sheep-vpn

    NAT (inside-Bct) 1 access list nat

    NAT (inside-Bct) 2-nat-ganja access list

    Access-group rdp on interface outside-Ganja

    !

    Access remote 0.0.0.0 0.0.0.0 85.*. *. 1 2

    Route outside Baku 10.254.17.24 255.255.255.248 10.254.17.10 1

    Route outside Baku 192.1.1.0 255.255.255.0 10.254.17.10 1

    Outside-Baku route 192.168.39.0 255.255.255.0 10.254.17.10 1

    Route outside-Ganja 192.168.45.0 255.255.255.0 10.254.17.18 1

    Route outside-Ganja 192.168.69.0 255.255.255.0 10.254.17.18 1

    Route outside-Ganja 192.168.184.0 255.255.255.0 10.254.17.18 1

    Route outside Baku 192.168.208.16 255.255.255.240 10.254.17.10 1

    Route outside-Ganja 192.168.208.112 255.255.255.240 10.254.17.18 1

    dynamic-access-policy-registration DfltAccessPolicy

    Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT

    Crypto ipsec transform-set newset aes - esp esp-md5-hmac

    Crypto ipsec transform-set esp-3des esp-md5-hmac vpnclienttrans

    Crypto ipsec transform-set vpnclienttrans transport mode

    Crypto ipsec transform-set esp-3des esp-md5-hmac raccess

    life crypto ipsec security association seconds 214748364

    Crypto ipsec kilobytes of life security-association 214748364

    raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map

    vpnclientmap 30 card crypto ipsec-isakmp dynamic dyn1

    card crypto interface for remote access vpnclientmap

    crypto isakmp identity address

    ISAKMP crypto enable vpntest

    ISAKMP crypto enable outside-Baku

    ISAKMP crypto enable outside-Ganja

    crypto ISAKMP enable remote access

    ISAKMP crypto enable Interior-Bct

    crypto ISAKMP policy 30

    preshared authentication

    3des encryption

    md5 hash

    Group 2

    life 86400

    No encryption isakmp nat-traversal

    No vpn-addr-assign aaa

    Telnet timeout 5

    SSH 192.168.1.0 255.255.255.192 outside Baku

    SSH 10.254.17.26 255.255.255.255 outside Baku

    SSH 10.254.17.18 255.255.255.255 outside Baku

    SSH 10.254.17.10 255.255.255.255 outside Baku

    SSH 10.254.17.26 255.255.255.255 outside-Ganja

    SSH 10.254.17.18 255.255.255.255 outside-Ganja

    SSH 10.254.17.10 255.255.255.255 outside-Ganja

    SSH 192.168.1.0 255.255.255.192 Interior-Bct

    internal vpn group policy

    attributes of vpn group policy

    value of DNS-server 192.168.1.3

    Protocol-tunnel-VPN IPSec l2tp ipsec

    Split-tunnel-policy tunnelspecified

    Split-tunnel-network-list value split tunnel

    BCT.AZ value by default-field

    attributes global-tunnel-group DefaultRAGroup

    raccess address pool

    Group-RADIUS authentication server

    Group Policy - by default-vpn

    IPSec-attributes tunnel-group DefaultRAGroup

    pre-shared-key *.

    Hello

    For the Cisco VPN client, you would need a tunnel-group name configured on the ASA with a pre-shared key.

    Please see configuration below:

    http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

    or

    http://tinyurl.com/5t67hd

    Please see the section of tunnel-group config of the SAA.

    There is a tunnel-group called "rtptacvpn" and a pre-shared key associated with it. This group name is used by the VPN Client Group name.

    So, you would need a specific tunnel-group name configured with a pre-shared key and use it on the Cisco VPN Client.

    Secondly, because you are behind a router ADSL, I'm sure that's configured for NAT. can you please activate NAT - T on your ASA.

    "crypto isakmp nat-traversal.

    Thirdly, change the transformation of the value

    raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map

    Let me know the result.

    Thank you

    Gilbert

  • IOS VPN L2L + C2L (cisco IPSEC client)

    Hello

    need to configure a C2L (client to the LAN) vpn on a cisco router where there is already an ipsec vpn.

    !!! already configured on the ROUTER

    !

    crypto ISAKMP policy 1

    md5 hash

    preshared authentication

    address of cisco key crypto isakmp 0.0.0.0 0.0.0.0

    !

    !

    Crypto ipsec transform-set esp - esp-md5-hmac Tunnel

    !

    crypto dynamic-map 10 Road-Tunnel

    game of transformation-Tunnel

    match address 115

    !

    !

    !

    !

    Crypto map 10 ipsec-isakmp Crypto-Tunnel Dynamic Channel-Tunnel

    !

    point-to-point interface ATM0/1/0.1

    card crypto Crypto-Tunnel

    !

    access-list 115 permit ip 10.0.0.0 0.0.0.255 192.168.168.0 0.0.0.255

    access-list 115 permit ip 10.0.0.0 0.0.0.255 10.2.0.0 0.0.0.255

    access-list 115 deny ip 10.0.0.0 0.0.0.255 any

    !

    !!! new configuration for cisco ipsec client

    !

    no address Cisco key crypto isakmp 0.0.0.0 0.0.0.0

    address of cisco key crypto isakmp 0.0.0.0 0.0.0.0 no.-xauth

    !

    AAA new-model

    !

    AAA authentication login AutClient local

    AAA authorization groupauthor LAN

    !

    !

    username 0 pippo pippo

    !

    crypto ISAKMP policy 10

    BA 3des

    preshared authentication

    Group 2

    !

    ISAKMP crypto client configuration group vpnclient

    key 0-pippo

    DNS 10.10.10.10

    WINS 10.10.10.20

    domain cisco.com

    pool ippoolvpnclient

    Save-password

    ACL 188

    !

    !

    card crypto Crypto-Tunnel client authentication list AutClient

    card crypto Crypto-Tunnel isakmp authorization list groupauthor

    card crypto Crypto-Tunnel client configuration address respond

    card crypto Crypto-ipsec-isakmp dynamic dynmap Tunnel 20

    !

    Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT

    !

    Crypto-map dynamic dynmap 10

    match address 188

    Set transform-set RIGHT

    !

    !

    !

    !

    IP local pool ippoolvpnclient 10.99.0.1 10.99.0.30

    !

    access-list 188 note #.

    access-list 188 note # split tunneling VPN C2L

    access-list 188 allow ip 10.99.0.0 0.0.0.31 10.0.0.0 0.0.0.255

    !

    can you tell me if the new configuration is OK?

    Thank you all

    NOT the ACL should be the opposite. Sound from the point of view of the router.

    access-list 188 allow ip 10.2.0.0 0.0.0.255 10.5.0.0 0.0.0.31

    Concerning

    Farrukh

  • IPSec site to site VPN cisco VPN client routing problem and

    Hello

    I'm really stuck with the configuration of ipsec site to site vpn (hub to spoke, multiple rays) with cisco vpn remote client access to this vpn.

    The problem is with remote access - cisco vpn client access - I can communicate with hub lan - but I need also communication of all lans speaks of the cisco vpn client.

    There are on the shelves, there is no material used cisco - routers DLINK.

    Someone told me that it is possible to use NAT to translate remote access IP-lan-HUB customers and thus allow communication - but I'm unable to set up and operate.

    Can someone help me please?

    Thank you

    Peter

    RAYS - not cisco devices / another provider

    Cisco 1841 HSEC HUB:

    crypto ISAKMP policy 1

    BA 3des

    preshared authentication

    Group 2

    ISAKMP crypto key x xx address no.-xauth

    !

    the group x crypto isakmp client configuration

    x key

    pool vpnclientpool

    ACL 190

    include-local-lan

    !

    86400 seconds, duration of life crypto ipsec security association

    Crypto ipsec transform-set esp-3des esp-sha-hmac 1cisco

    !

    Crypto-map dynamic dynmap 10

    Set transform-set 1cisco

    !

    card crypto ETH0 client authentication list userauthen

    card crypto isakmp authorization list groupauthor ETH0

    client configuration address card crypto ETH0 answer

    ETH0 1 ipsec-isakmp crypto map

    set peer x

    Set transform-set 1cisco

    PFS group2 Set

    match address 180

    card ETH0 10-isakmp ipsec crypto dynamic dynmap

    !

    !

    interface FastEthernet0/1

    Description $ES_WAN$

    card crypto ETH0

    !

    IP local pool vpnclientpool 192.168.200.100 192.168.200.150

    !

    !

    overload of IP nat inside source list LOCAL interface FastEthernet0/1

    !

    IP access-list extended LOCAL

    deny ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

    deny ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

    IP 192.168.7.0 allow 0.0.0.255 any

    !

    access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

    access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

    !

    How the DLINK has been configured for traffic between the site to site VPN subnets? You are able to add multiple remote subnets on DLINK? If you can, then you must add the pool of Client VPN subnet.

    Alternatively, if you cannot add multiple subnet on DLINK router, you can change the pool of Client VPN 192.168.6.0/24, and on the crypto ACL between the site to site VPN, you must edit the 180 existing ACL

    DE:

    access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

    access-list 180 allow ip 192.168.200.0 0.0.0.255 192.168.1.0 0.0.0.255

    TO:

    access-list 180 allow ip 192.168.6.0 0.0.1.255 192.168.1.0 0.0.0.255

    Also change the ACL 190 split tunnel:

    DE:

    access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

    access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.200.0 0.0.0.255

    TO:

    access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.6.0 0.0.0.255

    access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.6.0 0.0.0.255

    Finally, replace the remote subnet 192.168.7.0/255.255.255.0 192.168.6.0/255.255.254.0 DLINK.

    Hope that helps.

  • integrated macOS Sierra Cisco IPsec VPN does not work anymore (impossible to validate the server certificate)

    Hello

    I just upgraded to macOS Sierra and built-in Cisco IPsec VPN no longer works. When you try to connect, I get a "cannot validate the certificate of the server. "Check your settings and try to reconnect" error message. I use Cisco ASA with self-signed certificates and everything worked fine with previous versions of OS X.

    Please help me, I need my VPN Thx a lot

    I am having the same problem with StrongSwan and help cert signed with the channel to complete certificates included in the pkcs12 file imported to the keychain. It was working properly in El Capitan, but now broken in the Sierra.

  • Cisco Cisco IPSEC VPN to encrypt but not decrypt

    Hello

    I have a vpn ipsec problem.

    packets are encapsulated and décapsulés but only in one direction. I don't understand why.

    VPN is already mounted on another router, I want to change the router but can't get the vpn have the new router

    Thank you for helping me

    PS: Sorry for my English

    Hello

    I looked at the configuration of your router RT-897VA once again, and I don't know if static NAT statements in there are supposed to work or not, but they won't because you have not specified any inside and outside interfaces. Configuration changes below correspond to the configuration of your router RT, check if their implementation makes a difference (the changes are indicated in bold):

    RT-897VA #show run
    Building configuration...

    Current configuration: 3933 bytes
    !
    ! 11:56:34 configuration was last modified THIS Friday, November 4, 2016
    !
    version 15.4
    horodateurs service debug datetime msec
    Log service timestamps datetime msec
    no password encryption service
    !
    RT-897VA host name
    !
    boot-start-marker
    boot-end-marker
    !
    !
    !
    No aaa new-model
    clock timezone THIS 1 0
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !

    !
    !
    !
    !
    domain IP XXXXX
    IP-name 194.2.0.20 Server
    IP-name 194.2.0.50 server
    IP cef
    No ipv6 cef
    !
    !
    !
    !
    !
    Authenticated MultiLink bundle-name Panel
    VPDN enable
    !
    VPDN-Group 1
    ! Default L2TP VPDN group
    accept-dialin
    L2tp Protocol
    virtual-model 1
    tunnel L2TP non-session timeout 15
    !
    !
    default value for the field
    !
    !
    !
    !
    !
    !
    !
    CTS verbose logging
    license udi pid C897VA-K9 sn FCZ2030DL
    !
    !
    username password privilege 15 itef 0...
    !
    !
    !
    !
    !
    VDSL controller 0
    !
    property intellectual ssh rsa keypair-name XXX
    property intellectual ssh version 2
    !
    !
    crypto ISAKMP policy 1
    BA aes
    preshared authentication
    Group 2
    !
    crypto ISAKMP policy 2
    BA aes
    preshared authentication
    Group 2
    ISAKMP crypto key cleidentique address IP-WAN-B
    !
    !
    Crypto ipsec transform-set aes - esp esp-sha-hmac toto
    tunnel mode
    !
    !
    !
    crypto map ipsec-isakmp TUNNEL 1
    counterpart Set IP-WAN-B
    Set transform-set toto
    match address TUNNEL-DATA
    crypto map ipsec-isakmp TUNNEL 2
    counterpart Set IP-WAN-B
    Set transform-set toto
    match TUNNEL-TOIP address
    !
    !
    !
    !
    !
    !
    ATM0 interface
    no ip address
    Shutdown
    No atm ilmi-keepalive
    !
    interface BRI0
    no ip address
    encapsulation hdlc
    Shutdown
    Multidrop ISDN endpoint
    !
    interface Ethernet0
    no ip address
    Shutdown
    !
    interface GigabitEthernet0
    Description BOX-SWITCH
    switchport trunk vlan 101 native
    switchport mode trunk
    no ip address
    spanning tree portfast
    !
    interface GigabitEthernet1
    no ip address
    !
    interface GigabitEthernet2
    no ip address
    !
    interface GigabitEthernet3
    no ip address
    !
    interface GigabitEthernet4
    no ip address
    !
    interface GigabitEthernet5
    no ip address
    !
    interface GigabitEthernet6
    no ip address
    !
    interface GigabitEthernet7
    no ip address
    !
    interface GigabitEthernet8
    WAN description
    IP address IP WAN - A 255.255.255.240
    IP virtual-reassembly in
    NAT outside IP
    automatic duplex
    automatic speed
    card crypto TUNNEL
    !
    interface Vlan1
    no ip address
    !
    interface Vlan101
    VLAN-DATA description
    IP 192.168.101.251 255.255.255.0
    IP nat inside
    IP virtual-reassembly in
    !
    interface Vlan111
    VLAN-TOIP description
    IP 192.168.111.251 255.255.255.0
    IP virtual-reassembly in
    !
    IP forward-Protocol ND
    no ip address of the http server
    no ip http secure server
    !
    !
    IP nat inside source static tcp IP 25 expandable 25 192.168.101.2
    IP nat inside source static tcp IP 80 80 extensible 192.168.101.2
    IP nat inside source static tcp 192.168.101.2 extensible IP 443 443
    IP nat inside source static tcp 192.168.101.31 3201 IP extensible 3201
    IP nat inside source static tcp 192.168.101.31 80 extensible IP 3280
    IP nat inside source static tcp IP 443 33443 extensible 192.168.101.11
    overload of IP nat inside source list NAT interface GigabitEthernet8
    IP route 0.0.0.0 0.0.0.0 XXXX (ADSL router)
    IP route 192.168.100.0 255.255.255.0 IP-WAN-B

    NAT extended IP access list
    deny ip 192.168.101.0 0.0.0.255 192.168.100.0 0.0.0.255
    IP 192.168.101.0 allow 0.0.0.255 any
    access list IP-TUNNEL-DATA extents
    IP 192.168.101.0 allow 0.0.0.255 192.168.100.0 0.0.0.255
    TUNNEL-TOIP extended IP access list
    IP 192.168.110.0 allow 0.0.0.255 192.168.111.0 0.0.0.255
    !
    access list IP-TUNNEL-DATA extents
    IP 192.168.101.0 allow 0.0.0.255 192.168.100.0 0.0.0.255
    permit tcp host 192.168.101.3 192.168.0.0 0.0.0.255 established
    TUNNEL-TOIP extended IP access list
    IP 192.168.111.0 allow 0.0.0.255 192.168.110.0 0.0.0.255
    !
    !
    !
    control plan
    !
    !
    MGCP behavior considered range tgcp only
    MGCP comedia-role behavior no
    disable the behavior MGCP comedia-check-media-src
    disable the behavior of MGCP comedia-sdp-force
    !
    profile MGCP default
    !
    !
    !
    !
    !
    !
    !
    Line con 0
    no activation of the modem
    line to 0
    line vty 0 4
    privilege level 15
    password...
    opening of session
    transport input telnet ssh
    line vty 5 15
    privilege level 15
    password...
    opening of session
    transport input telnet ssh
    !
    Scheduler allocate 20000 1000
    !
    !
    !
    end

  • IPSec vpn cisco asa and acs 5.1

    We have configured authentication ipsec vpn cisco asa acs 5.1:

    Here is the config in cisco vpn 5580:

    standard access list acltest allow 10.10.30.0 255.255.255.0

    RADIUS protocol AAA-server Gserver

    AAA-server host 10.1.8.10 Gserver (inside)

    Cisco key

    AAA-server host 10.1.8.11 Gserver (inside)

    Cisco key

    internal group gpTest strategy

    gpTest group policy attributes

    Protocol-tunnel-VPN IPSec

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list acltest

    type tunnel-group test remote access

    tunnel-group test general attributes

    address localpool pool

    Group Policy - by default-gpTest

    authentication-server-group LOCAL Gserver

    authorization-server-group Gserver

    accounting-server-group Gserver

    IPSec-attributes of tunnel-group test

    pre-shared-key cisco123

    GBA, we config user group: VPN users. all VPN users in this group. ACS can visit his political profile: If the user in the 'VPN users' group, access ACS.

    When we connect from a VPN Client to the server, all users connect to success. When you see the parser in ACS journal, each user success connect also get

    error:

    22040 wrong password or invalid shared secret

    (pls see picture to attach it)

    the system still works, but I don't know why, we get the error log.

    Thanks for any help you can provide!

    Duyen

    Hello Duyen,

    I think I've narrowed the issue. When remote access VPN using RADIUS authentication we must keep in mind that authentication and authorization are included on the same package.

    Depending on your configuration, the ACS is defined as a server RADIUS (Gserver Protocol radius aaa server) and becomes the VPN Tunnel authenticated and 'authorized' on this server group:

    authentication-server-group LOCAL Gserver

    authorization-server-group Gserver

    As noted above, the RADIUS of request/response includes authentication and authorization on the same package. This seems to be a problem of incorrect configuration that we should not set up the 'permission' in the Tunnel of the group.

    Please remove the authorization under the Tunnel of Group:

    No authorization-server-group Gserver

    Please test the connection again and check the logs of the ACS. At this point there are only sucessful newspaper reported on the side of the ACS.

    Is 'Permission-server-group' LDAP permission when authenticating to a LDAP server so to retrieve the attributes of permission on the server. RAY doesn't have the command as explained above.

    I hope this helps.

    Kind regards.

  • Jabber of Cisco on Cisco ipsec VPN client

    Hello

    I wonder if anyone has had this problem.  I am currently using the 9.2.3 J4W customer and when I use Jabber in my office, everything works fine.  IM works very well and my incoming and outgoing calls work.   The question I have is when I work from home on my personal wifi and customer VPN Cisco (version 5.0.07.0290) ipsec remote in my area that the instant messaging and presence features work fine however only outgoing calls work. With Jabber, I can dial any DN in my organization and a willingness to work. The only problem is when someone tries to call me, I'll never get an alert for the incoming call.   However my ip back to my desk phone will be keep ringing and I'll see the voicemail and calls to jabber?   For some reason any call does not make for me on my VPN session.   I'm not sure of what could be the problem.   Jabber has certain requirements on ipsec VPN to work?  We use the ASA 5510 firewall and VPN endpoint.

    Thank you

    William Gonzalez

    CCNA R & S

    William,

    We recently had this problem: one of my other network admins had to prosecute with TAC, their resolution is to add

    a static NAT on our ASA for external source outside translation is your VPN network, destination is your VPN network.

    Thank you

  • Router Cisco IPsec VPN client

    Hello

    I would like if it is possible to make the IPsec VPN connection as a customer.

    ISP router (VDSL connection)

    <--->Cisco 887 <---->pc more with conditional redirection

    VPN router (as strongVPN)

    Thank you for your help.

    Best regards

    Hi Bruno.

    Yes the IOS router may be a VPN client, it is called easy VPN:

    How to configure Easy VPN Cisco IOS (server and client)

    * The server must be a Cisco device such as another router or an ASA.

    Keep me posted.

    Thank you.

    Portu.

    Please note all useful messages.

  • Customer Cisco IPSec vpn cisco ios router <>==

    Hello

    I need to implement ipsec vpn for all users of 10-15. They all use the vpn cisco 5.x client and we have a router for cisco ios at the office. We already have a situation of work for these users. However, it has become a necessity which known only devices (laptops company) are allowed to install a virtual private network.

    I think that the only way to achieve this is to use certificates. But we don't won't to buy certificates if there is a free way to implement. So my question is

    (1) what are the options I have to configure vpn ipsec, where only known devices can properly configure a vpn and all unknown devices are blocked?

    (2) if the certificate is the only way. Can I somehow produce these certificates myself using cisco router ios?

    (3) someone at - it an example of a similar installation/configuration?

    Thanks in advance.

    Kind regards

    M.

    Unfortunately if you connect to the router IOS, there is no other way except using the certificate. If you connect to a Cisco ASA firewall, then you can identify the laptop company using DAP (Dynamic Access Policy).

  • Support VPN Cisco 881

    Hi all

    I am not cisco trained or worked with cisco, im a complete beginner in Cisco platforms. We are an IT support MPH and we have recently taken on a client that has an office abroad using a Cisco 881 device with a Draytek router to the United Kingdom. Site to site connectivity is necessary. I watched and watched videos of youtube on how to configure the VPN and think I have it in place by using the config on the cisco below:

    crypto ISAKMP policy 1
    BA 3des
    preshared authentication
    Group 2
    lifetime 28800
    isakmp encryption key * address *.
    !
    Crypto ipsec transform-set esp-3des esp-sha-hmac sha3des
    !
    crypto map 1 VPN ipsec-isakmp
    set peer *.
    Set transform-set sha3des
    PFS group2 Set
    match address UK

    !

    interface FastEthernet4
    IP address
    IP access-group netbios in
    IP access-group netbios on
    no ip proxy-arp
    NAT outside IP
    IP virtual-reassembly in
    no ip-cache cef route
    no ip route cache
    automatic duplex
    automatic speed
    No cdp enable
    VPN crypto card

    !
    interface Vlan1
    secondary IP address
    IP 255.255.255.0
    IP access-group netbios in
    IP access-group netbios on
    no ip proxy-arp
    IP nat inside
    IP virtual-reassembly in
    no ip-cache cef route
    no ip route cache
    !

    UK extended IP access list
    allow IP 0.0.0.255 0.0.0.255
    allow IP 0.0.0.255 0.0.0.255

    It shows the VPN and active but there is no movement between the two and I do not know why...

    Current state of the session crypto

    Interface: FastEthernet4
    The session state: UP-ACTIVE
    Peer: port of 500
    IKEv1 SA: local remote 500 500 Active
    FLOW IPSEC: ip allow /255.255.255.0 /255.255.255.0
    Active sAs: 0, origin: card crypto
    FLOW IPSEC: ip allow /255.255.255.0 /255.255.255.0
    Active sAs: 2, origin: card crypto

    So it all seems perfect, however, if I try and ping the remote remote sites over ip LAN router I get the following:

    Type to abort escape sequence.
    Send 5, 100 bytes to ICMP echoes, waiting time is 2 seconds:
    .....
    Success rate is 0% (0/5)

    I also can't ping the remote site in the Cisco lan.

    I think that it is towards the end of cisco, the Draytek is a basic router and no routing is able to be configured. It does it automatically. The VPN is so no traffic...

    Please can someone point me in the right directoin?

    Thank you

    The additional ip route does not harm even if it is not needed. I love these additional routes that they can serve as a sort of "online documentation" when it is used with a keyword "name" extra at the end.

    Your NAT - ACL does not have the traffic. Just add the following:

     ip access-list ext 102 1 deny ip  0.0.0.255  0.0.0.255 

  • Client VPN Cisco router Cisco, MSW CA + certificates

    Dear Sirs,
    Let me approach you on the following problem.

    I wanted to use a secure between the Cisco VPN client connection
    (Windows XP) and Cisco 2821 with certificate-based authentication.
    I used the Microsoft certification authority (Windows 2003 server).
    Cisco VPN client used eTokenPRO Aladdin as a certificate store.

    Certificate of MSW CA registration and implementation in eToken ran OK
    Customer VPN Cisco doesn't have a problem with the cooperation of eToken.
    Certificate of registration of Cisco2821 MSW ca ran okay too.

    Cisco 2821 configuration is standard. IOS version 12.4 (6).

    Attempt to connect to the client VPN Cisco on Cisco 2821 was
    last update of the error messages:

    ISAKMP: (1020): cannot get router cert or routerdoes do not have a cert: had to find DN!
    ISAKMP: (1020): ITS been RSA signature authentication more XAUTH using id ID_FQDN type
    ISAKMP (1020): payload ID
    next payload: 6
    type: 2
    FULL domain name: cisco - ca.firm.com
    Protocol: 17
    Port: 500
    Length: 25
    ISAKMP: (1020): the total payload length: 25
    ISAKMP (1020): no cert string to send to peers
    ISAKMP (1020): peer not specified not issuing and none found appropriate profile
    ISAKMP (1020): Action of WSF returned the error: 2
    ISAKMP: (1020): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    ISAKMP: (1020): former State = new State IKE_R_MM5 = IKE_P1_COMPLETE

    Is there some refence where is possible to find some information on
    This problem? There is someone who knows how to understand these mistakes?
    Thank you very much for your help.

    Best regards
    P.Sonenberk

    PS Some useful information for people who are interested in the above problem.

    Address IP of Cisco 2821 10.1.1.220, client VPN IP address is 10.1.1.133.
    MSW's IP 10.1.1.50.
    Important parts of the Cisco 2821 configuration:

    !
    cisco-ca hostname
    !
    ................
    AAA new-model
    !
    AAA authentication login default local
    AAA authentication login sdm_vpn_xauth_ml_1 local
    AAA authorization exec default local
    AAA authorization sdm_vpn_group_ml_1 LAN
    !
    ...............
    IP domain name firm.com
    host IP company-cu 10.1.1.50
    host to IP cisco-vpn1 10.1.1.133
    name of the IP-server 10.1.1.33
    !
    Authenticated MultiLink bundle-name Panel
    !
    Crypto pki trustpoint TP-self-signed-4097309259
    enrollment selfsigned
    name of the object cn = IOS - Self - signed - certificate - 4097309259
    revocation checking no
    rsakeypair TP-self-signed-4097309259
    !
    Crypto pki trustpoint company-cu
    registration mode ra
    Enrollment url http://10.1.1.50:80/certsrv/mscep/mscep.dll
    use of ike
    Serial number no
    IP address no
    password 7 005C31272503535729701A1B5E40523647
    revocation checking no
    !
    TP-self-signed-4097309259 crypto pki certificate chain
    certificate self-signed 01
    30820249 308201B 2 A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030
    .............
    FEDDCCEA 8FD14836 24CDD736 34
    quit smoking
    company-cu pki encryption certificate chain
    certificate 1150A66F000100000013
    30820509 308203F1 A0030201 02020 HAS 11 092A 8648 01000000 13300 06 50A66F00
    ...............
    9E417C44 2062BFD5 F4FB9C0B AA
    quit smoking
    certificate ca 51BAC7C822D1F6A3469D1ADC32D0EB8C
    30820489 30820371 A0030201 BAC7C822 02021051 D1F6A346 9D1ADC32 D0EB8C30
    ...............
    C379F382 36E0A54E 0A6278A7 46
    quit smoking
    !
    ...................
    crypto ISAKMP policy 30
    BA 3des
    md5 hash
    authentication rsa-BA
    Group 2
    ISAKMP crypto identity hostname
    !
    Configuration group customer isakmp crypto Group159
    key Key159Key
    pool SDM_POOL_1
    ACL 100
    !
    the crypto isakmp client configuration group them
    domain firm.com
    pool SDM_POOL_1
    ACL 100
    !
    Crypto ipsec transform-set esp-3des esp-md5-hmac 3DES-MD5
    !
    crypto dynamic-map SDM_DYNMAP_1 1
    the transform-set 3DES-MD5 value
    market arriere-route
    !
    card crypto SDM_CMAP_1 client authentication list sdm_vpn_xauth_ml_1
    map SDM_CMAP_1 isakmp authorization list sdm_vpn_group_ml_1 crypto
    client configuration address map SDM_CMAP_1 crypto answer
    map SDM_CMAP_1 65535-isakmp dynamic SDM_DYNMAP_1 ipsec crypto
    !
    ................
    !
    end

    status company-cu of Cisco-ca #show cryptographic pki trustpoints
    Trustpoint company-cu:
    Issuing CA certificate configured:
    Name of the object:
    CN = firm-cu, dc = company, dc = local
    Fingerprint MD5: 5026582F 8CF455F8 56151047 2FFAC0D6
    Fingerprint SHA1: 47B 74974 7C85EA48 760516DE AAC84C5D 4427E829
    Universal router configured certificate:
    Name of the object:
    host name = cisco - ca.firm.com
    Fingerprint MD5: E78702ED 47D5D36F B732CC4C BA97A4ED
    Fingerprint SHA1: 78DEAE7E ACC12F15 1DFB4EB8 7FC DC6F3B7E 00138
    State:
    Generated keys... Yes (general purpose, not exportable)
    Authenticated issuing certification authority... Yes
    Request certificate (s)... Yes

    Cisco-ca #sh crypto pubkey-door-key rsa
    Code: M - configured manually, C - excerpt from certificate

    Name of code use IP-address/VRF Keyring
    C Signature name of X.500 DN default:
    CN = firm-cu
    DC = company
    DC = local

    C signature by default cisco-vpn1

    IMPORTANT: I don't have a Cisco IOS Software: 12.4 (5), 12.3 (11) T08, 12.4 (4.7) PI03c,.
    12.4 (4.7) T - there is error in the cryptographic module.

    Hey guys, it's weird that the router is not find cert after IKE is the cert and validates, it is certainly not reason, but I would go ahead and set up the mapping of certificate on this router to force the client to associate with Group of IKE, for that matter, that you need to change your config a bit for use iskamp profiles :

    http://www.Cisco.com/en/us/docs/iOS/12_3t/12_3t8/feature/guide/gt_isakp.html

  • Problem with ping VPN cisco 877

    Hi all!

    I have a working VPN between a fortigate and a Cisco.

    I have a problem with ping network behind the cisco of the network behind the forti.

    When I ping to vlan2 cisco without problem (192.168.252.1) interface, but I can't ping a server in the vlan2 (192.168.252.2) behind the cisco.

    However the Cisco I can ping the server. In the forti, I see that ping to the interface vlan2 and server in vlan2 take in the same way, and I can see package.

    I post my config could see it it as blocking the ping from 10.41.2.36 to 192.168.252.2 while 192.168.252.1 ping is OK?

    IPSEC #show run
    Building configuration...

    Current configuration: 3302 bytes
    !
    ! Last modification of the configuration at 14:42:17 CEDT Friday, June 25, 2010
    ! NVRAM config update at 14:42:23 CEDT Friday, June 25, 2010
    !
    version 12.4
    no service button
    horodateurs service debug datetime msec
    Log service timestamps datetime localtime show-time zone
    encryption password service
    !
    IPSEC host name
    !
    boot-start-marker
    boot-end-marker
    !
    logging buffered 1000000
    enable secret 5 abdellah
    !
    No aaa new-model
    clock timezone GMT 1
    clock to summer time CEDT recurring last Sun Mar 02:00 last Sun Oct 03:00
    !
    !
    dot11 syslog
    IP cef
    No dhcp use connected vrf ip
    DHCP excluded-address IP 192.168.254.0 192.168.254.99
    DHCP excluded-address IP 192.168.254.128 192.168.254.255
    !
    IP dhcp DHCP pool
    network 192.168.254.0 255.255.255.0
    router by default - 192.168.254.254
    Server DNS A.A.A.A B.B.B.B
    !
    !
    no ip domain search
    name of the IP-server A.A.A.A
    name of the IP-server B.B.B.B
    !
    !
    !
    !
    !
    crypto ISAKMP policy 1
    BA aes 256
    preshared authentication
    Group 5
    ISAKMP crypto key ciscokey address IP_forti
    !
    !
    Crypto ipsec transform-set esp - aes 256 esp-sha-hmac vpntest
    !
    myvpn 10 ipsec-isakmp crypto map
    defined by peer IP_forti
    Set transform-set vpntest
    match address 101
    !
    Archives
    The config log
    hidekeys
    !
    !
    !
    !
    !
    interface Tunnel0
    IP 2.2.2.1 255.255.255.252
    source of Dialer0 tunnel
    destination of IP_forti tunnel
    myvpn card crypto
    !
    ATM0 interface
    bandwidth 320
    no ip address
    load-interval 30
    No atm ilmi-keepalive
    DSL-automatic operation mode
    !
    point-to-point interface ATM0.1
    MTU 1492
    bandwidth 160
    PVC 8/35
    VBR - nrt 160 160
    PPPoE-client dial-pool-number 1
    !
    !
    interface FastEthernet0
    switchport access vlan 2
    !
    interface FastEthernet1
    !
    interface FastEthernet2
    !
    interface FastEthernet3
    switchport access vlan 2
    !
    interface Vlan1
    IP 192.168.20.253 255.255.255.0
    IP nat inside
    no ip virtual-reassembly
    !
    interface Vlan2
    IP 192.168.252.1 255.255.255.0
    IP nat inside
    IP virtual-reassembly
    !
    interface Dialer0
    bandwidth 128
    the negotiated IP address
    NAT outside IP
    no ip virtual-reassembly
    encapsulation ppp
    load-interval 30
    Dialer pool 1
    Dialer-Group 1
    KeepAlive 1 2
    Authentication callin PPP chap Protocol
    PPP chap hostname [email protected] / * /
    PPP chap password 7 abdelkrim
    myvpn card crypto
    !
    IP forward-Protocol ND
    IP route 0.0.0.0 0.0.0.0 Dialer0
    IP route 10.41.2.32 Tunnel0 255.255.255.240
    !
    no ip address of the http server
    no ip http secure server
    The dns server IP
    translation of nat IP tcp-timeout 5400
    no ip nat service sip 5060 udp port
    overload of IP nat inside source list NAT interface Dialer0
    !
    IP access-list standard BROADCAST
    permit of 0.0.0.0
    deny all
    !
    NAT extended IP access list
    IP enable any host IP_cisco
    deny ip 192.168.252.0 0.0.0.255 10.41.2.32 0.0.0.31
    !
    access-list 101 permit ip 192.168.252.0 0.0.0.255 10.41.2.32 0.0.0.31
    public RO SNMP-server community
    3 RW 99 SNMP-server community
    SNMP-server community a RO
    SNMP-Server RO community oneCommunityRead
    not run cdp
    !
    !
    !
    control plan
    !
    !
    Line con 0
    password 7 abdelkrim
    opening of session
    no activation of the modem
    line to 0
    line vty 0 4
    password 7 aaaaa
    opening of session
    escape character 5
    !
    max-task-time 5000 Planner
    NTP-period clock 17175037
    Server NTP B.B.B.B
    Server NTP A.A.A.A

    end

    Alex,

    It's your GRE tunnel:

    interface Tunnel0
    IP 2.2.2.1 255.255.255.252
    source of Dialer0 tunnel
    destination of IP_forti tunnel
    myvpn card crypto

    You also have routing set by it.

    You don't need a GRE tunnel, nor do you need the road to tunnel if you want just IPsec tunnel.

  • Customer VPN CISCO C2691 4.9.01.0180 does not work

    Hello

    After reading and find information about the client IPsec and VPN som, I now try to make it work, but:

    The TEST LABORATORY is to follow:

    INTERNET-> (IP 192.168.10.1/24) C1841-> INT0/1 TEST LAB

    C2691 INT0/1 (IP 192.168.10.166/24)-> C2691 INT0/0 (IP 172.18.124.159/24)-> COMPUTER (DIFFICULTY IP 172.18.124.10/24)

    I can PING from the computer:

    192.168.10.1

    172.18.124.159

    But when I run the VPN, I have no communication, the PASSWORD and LOGIN are correct with the scrip.

    Here below what I get when I try to connect:

    Cisco Systems VPN Client Version 4.9.01.0180
    Copyright (C) 1998-2009 Cisco Systems, Inc.. All rights reserved.
    Type of client: Mac OS X
    Running: the Darwin 10.6.0 Darwin kernel Version 10.6.0: Wed Nov 10 18:13:17 PST 2010; root:XNU-1504.9.26~3/RELEASE_I386 i386
    Config files directory: / etc/opt/cisco-vpnclient

    1 20:23:49.072 14/01/2011 Sev = Info/4 CM / 0 x 43100002
    Start the login process

    2 20:23:49.073 14/01/2011 Sev = WARNING/2 CVPND / 0 x 83400011
    Send error - 28 package. ADR DST: 0xAC127CFF, ADR Src: 0xAC127C0A (DRVIFACE:1158).

    3 20:23:49.073 14/01/2011 Sev = WARNING/2 CVPND / 0 x 83400011
    Send error - 28 package. ADR DST: 0x0AD337FF, ADR Src: 0x0AD33702 (DRVIFACE:1158).

    4 20:23:49.073 14/01/2011 Sev = WARNING/2 CVPND / 0 x 83400011
    Send error - 28 package. ADR DST: 0x0A2581FF, ADR Src: 0x0A258102 (DRVIFACE:1158).

    5 20:23:49.080 14/01/2011 Sev = Info/4 CM / 0 x 43100004
    Establish a connection using Ethernet

    6 20:23:49.081 14/01/2011 Sev = Info/4 CM / 0 x 43100024
    Attempt to connect with the server "172.18.124.159".

    7 20:23:49.081 14/01/2011 Sev = Info/6 CM/0x4310002F
    Assigned TCP port local 49164 for the TCP connection.

    8 20:23:49.261 14/01/2011 Sev = Info/4 IPSEC / 0 x 43700008
    IPSec driver started successfully

    9 20:23:49.261 14/01/2011 Sev = Info/4 IPSEC / 0 x 43700014
    Remove all keys

    10 20:23:49.261 14/01/2011 Sev = Info/6 IPSEC / 0 x 43700020
    TCP SYN sent 172.18.124.159, src port 49164, port 10000 DST

    11 20:23:54.261 14/01/2011 Sev = Info/6 IPSEC / 0 x 43700020
    TCP SYN sent 172.18.124.159, src port 49164, port 10000 DST

    12 20:23:59.261 14/01/2011 Sev = Info/6 IPSEC / 0 x 43700020
    TCP SYN sent 172.18.124.159, src port 49164, port 10000 DST

    13 20:24:04.761 14/01/2011 Sev = Info/6 IPSEC / 0 x 43700020
    TCP SYN sent 172.18.124.159, src port 49164, port 10000 DST

    14 20:24:09.261 14/01/2011 Sev = Info/4 CM/0x4310002A
    Unable to establish a TCP connection on port 10000 with server '172.18.124.159 '.

    15 20:24:09.261 14/01/2011 Sev = Info/5 CM / 0 x 43100025
    Initializing CVPNDrv

    16 20:24:09.262 14/01/2011 Sev = Info/4 CM/0x4310002D
    Reset the TCP connection on port 10000

    17 20:24:09.262 14/01/2011 Sev = Info/6 CM / 0 x 43100030
    Removed the TCP port local 49164 for the TCP connection.

    18 20:24:09.262 14/01/2011 Sev = Info/4 CVPND/0x4340001F
    Separation of privileges: restore MTU on the main interface.

    19 20:24:09.262 14/01/2011 Sev = Info/6 IPSEC / 0 x 43700023
    TCP RST sent to 172.18.124.159, src port 49164, port 10000 DST

    20 20:24:09.262 14/01/2011 Sev = Info/4 IPSEC / 0 x 43700014
    Remove all keys

    21 20:24:09.263 14/01/2011 Sev = Info/4 IPSEC / 0 x 43700014
    Remove all keys

    22 20:24:09.263 14/01/2011 Sev = Info/4 IPSEC/0x4370000A
    IPSec driver successfully stopped

    The manuscript in the CISCO 2691 is just suited for my setup, I don't think that I made a few mistakes, but you never know.

    If has a first time, I'm able to establish a VPN connection to my computer and my router, I'll be happy, if I see my home network of the CISCO 1841 (ROUTER MAIN one) this will be perfect, that's also what I would like to check in.

    Here, the manuscript of the CISCO 2691:

    !
    version 12.4
    horodateurs service debug datetime msec
    Log service timestamps datetime msec
    no password encryption service
    !
    router host name
    !
    boot-start-marker
    boot system flash: c2691-adventerprisek9 - mz.124 - 5a .bin
    boot-end-marker
    !
    !
    AAA new-model
    !
    !
    AAA authentication login userauthen local
    AAA authorization groupauthor LAN
    !
    AAA - the id of the joint session
    !
    resources policy
    !
    IP cef
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    Fax fax-mail interface type
    0 username cisco password Cisco
    !
    !
    !
    crypto ISAKMP policy 3
    BA 3des
    preshared authentication
    Group 2
    !
    ISAKMP crypto client configuration group 3000client
    key cisco123
    DNS 8.8.8.8
    domain cisco.com
    pool ippool
    ACL 108
    !
    !
    Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
    !
    Crypto-map dynamic dynmap 10
    Set transform-set RIGHT
    !
    !
    map clientmap client to authenticate crypto list userauthen
    card crypto clientmap isakmp authorization list groupauthor
    client configuration address map clientmap crypto answer
    10 ipsec-isakmp crypto map clientmap Dynamics dynmap
    !
    !
    !
    !
    interface FastEthernet0/0
    IP 172.18.124.159 255.255.255.0
    automatic speed
    Half duplex
    clientmap card crypto
    !
    interface Serial0/0
    no ip address
    Shutdown
    !
    interface FastEthernet0/1
    IP 192.168.10.166 255.255.255.0
    automatic speed
    Half duplex
    !
    interface Serial1/0
    no ip address
    Shutdown
    series 0 restart delay
    No terminal-dce-enable-calendar
    !
    interface Serial1/1
    no ip address
    Shutdown
    series 0 restart delay
    No terminal-dce-enable-calendar
    !
    interface Serial1/2
    no ip address
    Shutdown
    series 0 restart delay
    No terminal-dce-enable-calendar
    !
    interface Serial1/3
    no ip address
    Shutdown
    series 0 restart delay
    No terminal-dce-enable-calendar
    !
    IP local pool ippool 192.168.10.170 192.168.10.175
    IP route 0.0.0.0 0.0.0.0 192.168.10.1
    !
    !
    IP http server
    no ip http secure server
    !
    access-list 108 permit ip 192.168.10.0 0.0.0.255 host 0.0.0.0
    !
    !
    !
    !
    control plan
    !
    !
    !
    !
    !
    !
    Dial-peer cor custom
    !
    !
    !
    !
    !
    !
    Line con 0
    transportation out all
    Speed 115200
    line to 0
    transportation out all
    line vty 0 4
    transport of entry all
    transportation out all
    !
    !
    end

    Best regards

    Didier

    Hi Didier,.

    Looking at your first series of VPN client logs, it seems that the VPN client is set to use IPSec/TCP on port 10000 while CTCP has not been enabled on the router.

    I suggest you to change the configuration on the client VPN IPSec/UDP rather than TCP. (Go to the tab "Transport" when you change the corresponding connection on the VPN client).

    Let me know if this helps out!

    See you soon,.

    Assia

  • Configuration VPN Cisco ASA5505 new 800

    I have 2 office buildings using routers Cisco 800 series with a L2L VPN between the two.  I'm upgrading from the router to an ASA5505 at one of the offices but cannot understand the L2L VPN on the SAA.  Specifically, may not know how to set the pre-shared key.  On the Cisco 800 there:

    ISAKMP crypto key address

    This doesn't seem to work on the SAA.  Can anyone help this?  Here is my current config on the Cisco 800...

    crypto ISAKMP policy 10

    BA 3des

    md5 hash

    preshared authentication

    Group 2

    ISAKMP crypto key

    address

    !

    !

    Crypto ipsec transform-set esp-3des esp-md5-hmac DUMAC3

    Crypto ipsec df - bit clear

    !

    MYmap 10 ipsec-isakmp crypto map

    defined by peer 75.148.153.217

    Set security-association second life 36000

    game of transformation-DUMAC3

    match address 101

    access-list 101 permit ip 192.168.1.0 0.0.0.255 192.168.7.0 0.0.0.255

    in your crypto-maps, the '10' and '65535' are the sequence numbers. A CM handset might look like this:

    address for correspondence primaryisp_map 10 101 crypto card

    peer set card crypto primaryisp_map 10 99.119.80.165

    primaryisp_map 10 set transform-set DUMAC3 ikev1 crypto card

    primaryisp_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    card crypto primaryisp_map interface primaryisp

Maybe you are looking for

  • Do not receive codes of two-step verification through the find my iPhone

    Hi all. When you try to connect to my Apple ID with two-step verification, I never seem to receive codes to check on my iPhone or iPad when I choose to sent them by find my iPhone (as opposed to SMS). Everyone knows this? My iDevices work very well w

  • Installation of Marvel Yukon 88E8040T Ethernet on Satellite U405 using Linux

    Sorry for my English. I am writing from Brazil, and the only reason I'm not posting in Portuguese is because I want to let this information available for a larger number of users. I had a few problems although the Marvel Yukon Ethernet PCI on my Debi

  • Satellite A350D - 20K - Question about upgrade second HDD + Temperature

    I have a question about my laptop. I have notticed it is a second location of HARD disk on the bottom.Is it possible to use this to increase my storage?And if yes, how do I do that? I don't see all the connectors.What type of HARD drive to use in cas

  • Restore failed Satellite M30 using the recovery CD

    My laptop was running very slow because he has been blocked for 5 years. Decided to wipe and start over.I tried a full restore using the original recovery CD in the course of which the erroneous application, leaving me with a hard drive that is detec

  • Neither 9860

    Hi, I just tried setting up the chaisis ethercat 9144 with a module of the series nor 9860 c and crio 9035 is the master. But I can't get the module to appear in the project. The 9860 module is supported by the chaisis ethercat 9144? If this is not t