VPN connects but no remote LAN access

Hello

I'll put up on a PIX 501 VPN remote access.

When I try to connect via VPN software, I am able to connect but I am unable to access LAN resources.

I have pasted below part of which seems relevant to my setup. I'm stuck on this issue, could someone help me? Thanks in advance.

ethernet0 nameif outside security0
nameif ethernet1 inside the security100
test.local domain name
name 10.0.2.0 inside
name 10.0.2.13 MSExchange-en
2.2.2.2 the MSExchange-out name

outside_access_in tcp allowed access list all gt 1023 host 2.2.2.2 eq smtp
outside_access_in list access permit tcp any host 2.2.2.2 eq https
outside_access_in list access permit tcp any host 2.2.2.2 eq www
inside_outbound_nat0_acl 10.0.2.0 ip access list allow 255.255.255.0 192.168.235.0 255.255.255.192
access-list 101 permit icmp any one

3.3.3.3 exterior IP address 255.255.255.0
IP address inside 10.0.2.254 255.255.255.0
IP local pool vpn_pool 192.168.235.1 - 192.168.235.15
IP local pool vpn_pool_2 192.168.235.16 - 192.168.235.40

1 3.3.3.4 (outside) global
NAT (inside) 0-list of access inside_outbound_nat0_acl
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
static (inside, outside) 2.2.2.2 10.0.2.13 netmask 255.255.255.255 1000 1000
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 3.3.3.1 1

RADIUS Protocol RADIUS AAA server
AAA-server RADIUS (inside) host 10.0.2.3 * timeout 10
AAA-server local LOCAL Protocol

Permitted connection ipsec sysopt
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto-map dynamic dynmap 10 game of transformation-ESP-3DES-MD5
map outside_map 90-isakmp ipsec crypto dynamic dynmap
card crypto outside_map the LOCAL RADIUS client authentication
outside_map interface card crypto outside
ISAKMP allows outside
part of pre authentication ISAKMP policy 20
ISAKMP policy 20 3des encryption
ISAKMP policy 20 md5 hash
20 2 ISAKMP policy group
ISAKMP duration strategy of life 20 86400
vpngroup signal address vpn_pool pool
vpngroup dns-server 10.0.2.3 signal
vpngroup default-field test.local signal
vpngroup idle time 1800 signal
vpngroup max-time 14400 signal
signal vpngroup password *.
vpngroup TF vpn_pool_2 address pool
vpngroup dns-server 10.0.2.3 TF
TF vpngroup default-domain test.local
vpngroup TF 1800 idle time
vpngroup max-time 14400 TF
TF vpngroup password *.

Kind regards

Joana

Very similar to the question of the configuration of the switch. You should check if there is no specific roads on the switch outside the default gateway. The switch should route the subnet pool ip to the firewall (10.0.2.254).

Tags: Cisco Security

Similar Questions

  • Client VPN connects but not internal LAN access or Ping

    Hi all.

    I'm new on this forum and kindly asking for your help because I'm stuck.

    I have an ADSL router cisco 877 which I configured easy VPN server.
    Now the Cisco VPN client ver 5.0 to connect successfully to the VPN server, but when you try to access/ping computers on the internal network, there is no response.

    The configuration is below. Please let know us where I was going or what I missed.
    [code]

    Building configuration...

    Current configuration: 4574 bytes
    !
    version 12.4
    no service button
    horodateurs service debug datetime msec
    Log service timestamps datetime msec
    encryption password service
    !
    boot-start-marker
    boot-end-marker
    !
    enable secret 5 $1$ $86dn J8HrK9kCQ8G9aPAm6xe4o1
    enable password 7 13151601181B54382F
    !
    AAA new-model
    !
    !
    AAA authentication login default local
    AAA authentication login internal_affairs_vpn_1 local
    AAA authorization exec default local
    AAA authorization internal_affairs_vpn_group_1 LAN
    !
    !
    AAA - the id of the joint session
    !
    Crypto pki trustpoint TP-self-signed-2122144568
    enrollment selfsigned
    name of the object cn = IOS - Self - signed - certificate - 2122144568
    revocation checking no
    rsakeypair TP-self-signed-2122144568
    !
    !
    TP-self-signed-2122144568 crypto pki certificate chain
    self-signed certificate 03
    30820248 308201B 1 A0030201 02020103 300 D 0609 2A 864886 F70D0101 04050030
    2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
    69666963 32313232 31343435 6174652D 3638301E 170 3032 30333032 32303537
    31375A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
    4F532D53 5369676E 656C662D 43 65727469 66696361 74652 32 31323231 65642D
    34343536 3830819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
    8100D3EA 07EC5D66 F4DD8ACC 5540BDBE 009B3C26 598EC99C D99D935A 51292F96
    F495E5A9 8D012B0E 73EA7639 3B 586799 187993F5 ED9CA31C 788756DD 6BDB1B2B
    4D7AA7F0 B07CF82F F2A29E86 E18B442C 550E22D2 E92D9914 105B7D59 253BBEA1
    D84636B4 A4B4B300 7946CE84 E9A63D2E 7789B03A 6ADDB04E B21EC207 CCFEAE0B
    30 HAS A 50203 010001, 3 1 130101 301B 0603 030101FF FF040530 0F060355 70306E30
    551 1104 14301282 10494E54 45524E41 4C5F4146 46414952 53301F06 03551D 23
    04183016 8014FA0F B3C9C651 7FD91EFA 3F63EAE8 6C83C80D 8AE2301D 0603551D
    0E041604 14FA0FB3 C9C6517F D91EFA3F 63EAE86C 83C80D8A E2300D06 092A 8648
    86F70D01 01040500 03818100 A1026DDC C91CAEB2 3C62AF92 D6B25EB2 CA 950, 920
    313BCF26 4A35B039 A4F806A0 8CB54D11 6AF1ABAA A770604B 4403F345 0351361B
    E2CF2950 26974F4A 95951862 401A4F76 C816590C 2FFCB115 9A8B3E96 4373FFE1
    33D744F7 E0FDDE61 B5B48497 9516C3C6 A3157957 C621668E A83B5E33 2420F962
    9142DD9E B6E9D74A 899A 9653
    quit smoking
    dot11 syslog
    IP cef
    No dhcp use connected vrf ip
    DHCP excluded-address IP 10.10.10.1
    !
    IP dhcp pool dhcplan
    Network 10.0.0.0 255.0.0.0
    DNS-server 196.0.50.50 81.199.21.94
    default router 10.10.10.1
    Rental 7
    !
    !
    property intellectual auth-proxy max-nodata-& 3
    property intellectual admission max-nodata-& 3
    name of the IP-server 81.199.21.94
    !
    !
    !
    VPN username password 7 095A5E07
    username fred privilege 15 password 7 1411000E08
    username ciscovpn password 7 01100F175804101F2F
    !
    !
    crypto ISAKMP policy 1
    BA 3des
    preshared authentication
    Group 2
    !
    ISAKMP crypto client configuration group internal_affairs_vpn
    key *.
    DNS 196.0.50.50 81.199.21.94
    pool ippool
    ACL 108
    !
    !
    Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
    !
    Crypto-map dynamic internal_affairs_DYNMAP_1 10
    Set transform-set RIGHT
    market arriere-route
    !
    !
    card crypto client internal_affairs_CMAP_1 of authentication list internal_affairs_vpn
    card crypto isakmp authorization list internal_affairs_vpn_group_1 internal_affairs_CMAP_1
    client configuration address card crypto internal_affairs_CMAP_1 answer
    ipsec 10-isakmp crypto map internal_affairs_CMAP_1 Dynamics internal_affairs_DYNMAP_1
    !
    Archives
    The config log
    hidekeys
    !
    !
    !
    Bridge IRB
    !
    !
    interface Loopback0
    2.2.2.2 the IP 255.255.255.255
    !
    ATM0 interface
    no ip address
    ATM vc-per-vp 512
    No atm ilmi-keepalive
    PVC 0/32
    aal5snap encapsulation
    Protocol ip inarp
    !
    DSL-automatic operation mode
    Bridge-Group 1
    !
    interface FastEthernet0
    !
    interface FastEthernet1
    !
    interface FastEthernet2
    !
    interface FastEthernet3
    !
    interface Vlan1
    description of the local lan interface
    IP 10.10.10.1 255.0.0.0
    IP nat inside
    IP virtual-reassembly
    !
    interface BVI1
    internet interface Description
    IP 197.0.4.174 255.255.255.252
    NAT outside IP
    IP virtual-reassembly
    internal_affairs_CMAP_1 card crypto
    !
    IP local pool ippool 192.168.192.1 192.168.192.200
    IP forward-Protocol ND
    IP route 0.0.0.0 0.0.0.0 196.0.4.173
    !
    IP http server
    local IP http authentication
    IP http secure server
    IP nat inside source list interface BVI1 NAT overload
    IP nat inside source static tcp 2.2.2.2 23 23 BVI1 interface
    !
    NAT extended IP access list
    allow an ip
    !
    access-list 108 allow ip 10.0.0.0 0.255.255.255 192.168.192.0 0.0.0.255
    !
    !
    !
    control plan
    !
    Bridge Protocol ieee 1
    1 channel ip bridge
    !
    Line con 0
    password 7 0216054818115F3348
    no activation of the modem
    line to 0
    line vty 0 4
    password 7 06160E325F59590B01
    !
    max-task-time 5000 Planner
    end

    Since this is a named ACL, you need to change ACL configuration mode:

    NAT extended IP access list

    Then, make the changes.

    Federico.

  • AnyConnect VPN connected but not in LAN access

    Hello

    I just connfigured an ASA to remote VPN. I think everything works but I do not have access

    for customers in the Local LAN behind the ASA.

    PC <==internet==>outside of the SAA inside<=LAN=> PC

    After AnyConnect has established the connection I can ping inside the Interface of the ASA

    but I can't Ping the PC behind the inside Interface.

    Here is the config of the ASA5505:

    : Saved

    :

    ASA Version 8.2 (1)

    !

    asa5505 hostname

    activate 8Ry2YjIyt7RRXU24 encrypted password

    2KFQnbNIdI.2KYOU encrypted passwd

    names of

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 192.168.1.1 255.255.255.0

    !

    interface Vlan2

    nameif outside

    security-level 0

    IP 192.168.178.254 255.255.255.0

    !

    interface Ethernet0/0

    switchport access vlan 2

    !

    interface Ethernet0/1

    !

    interface Ethernet0/2

    Shutdown

    !

    interface Ethernet0/3

    Shutdown

    !

    interface Ethernet0/4

    Shutdown

    !

    interface Ethernet0/5

    Shutdown

    !

    interface Ethernet0/6

    Shutdown

    !

    interface Ethernet0/7

    Shutdown

    !

    passive FTP mode

    Inside_ICMP list extended access permit icmp any any echo response

    Inside_ICMP list extended access permit icmp any any source-quench

    Inside_ICMP list extended access allow all unreachable icmp

    Inside_ICMP list extended access permit icmp any one time exceed

    access-list outside_cryptomap_2 note ACL traffic von ASA5505 zur ASA5510

    outside_cryptomap_2 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.0

    no_NAT to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.0

    no_NAT to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.178.0 255.255.255.0

    tunnel of splitting allowed access list standard 192.168.1.0 255.255.255.0

    pager lines 24

    Within 1500 MTU

    Outside 1500 MTU

    mask 192.168.1.10 - 192.168.1.15 255.255.255.0 IP local pool SSLClientPool

    ICMP unreachable rate-limit 1 burst-size 1

    don't allow no asdm history

    ARP timeout 14400

    Global 1 interface (outside)

    NAT (inside) 0-list of access no_NAT

    NAT (inside) 1 192.168.1.0 255.255.255.0

    Access-group Inside_ICMP in interface outside

    Route outside 0.0.0.0 0.0.0.0 192.168.178.1 1

    Route outside 192.168.10.0 255.255.255.0 192.168.178.230 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    dynamic-access-policy-registration DfltAccessPolicy

    AAA authentication http LOCAL console

    Enable http server

    http 192.168.1.0 255.255.255.0 inside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Crypto ipsec transform-set-3DESSHA FRA esp-3des esp-sha-hmac

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    card crypto outside_map 2 match address outside_cryptomap_2

    peer set card crypto outside_map 2 192.168.178.230

    card crypto outside_map 2 game of transformation-FRA-3DESSHA

    outside_map interface card crypto outside

    Crypto ca trustpoint localtrust

    registration auto

    domain name full cisco - asa5505.fritz.box

    name of the object CN = cisco - asa5505.fritz.box

    sslvpnkeypair key pair

    Configure CRL

    Crypto ca certificate chain localtrust

    certificate fa647850

    3082020b a0030201 30820174 020204fa 0d06092a 64785030 864886f7 0d 010104

    0500304 06035504 03131763 6973636f 617361 35353035 2e667269 2d 3120301e a

    747a2e62 6f783126 30240609 2a 864886 f70d0109 02161763 6973636f 2d 617361

    2e667269 35353035 747a2e62 6f78301e 170d 3132 31303132 31383434 31305a 17

    323231 30313031 38343431 06035504 03131763 6973636f 3120301e 305a304a 0d

    617361 35353035 2e667269 747a2e62 6f783126 2a 864886 30240609 f70d0109 2D

    6973636f 02161763 2d 617361 35353035 2e667269 747a2e62 6f783081 9f300d06

    d6279e1c 8181009f 092a 8648 86f70d01 01010500 03818d 30818902 00 38454fc 9

    705e1e58 762edc35 e64262fb ee55f47b 8d62dda2 102c8a22 c97e395f 2a9c0ebb

    f2881528 beb6e9c3 89d91dda f7fe77a4 2a1fda55 f8d930b8 3310a05f 622dfc8f

    d48ea749 7bbc4520 68 has 06392 d65d3b87 0270e41b 512a4e89 94e60167 e2fa854a

    87ec04fa e95df04f 3ff3336e c7437e30 ffbd90b5 47308502 03010001 300 d 0609

    2a 864886 04050003 81810065 cc9e6414 3c322d1d b191983c 97b474a8 f70d0101

    2e5c7774 9d54d3ec fc4ee92d c72eef27 a79ce95a da83424f b05721c0 9119e7ea

    c5431998 e6cd8272 de17b5ff 5b1839b5 795fb2a0 2d10b479 056478fa 041555dd

    bfe3960a 4fe596ec de54d58b a5fa187e 5967789a a26872ef a33b73ec 7d7673b9

    c8af6eb0 46425cd 2 765f667d 4022c 6

    quit smoking

    crypto ISAKMP allow outside

    crypto ISAKMP policy 1

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 65535

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    Telnet timeout 5

    SSH timeout 5

    Console timeout 0

    management-access inside

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    localtrust point of trust SSL outdoors

    WebVPN

    allow outside

    SVC disk0:/anyconnect-win-2.3.0254-k9.pkg 1 image

    SVC disk0:/anyconnect-wince-ARMv4I-2.3.0254-k9.pkg 2 image

    enable SVC

    tunnel-group-list activate

    internal SSLClientPolicy group strategy

    attributes of Group Policy SSLClientPolicy

    VPN-tunnel-Protocol svc

    Split-tunnel-policy tunnelspecified

    Split-tunnel-network-list value split tunnel

    the address value SSLClientPool pools

    WebVPN

    SVC Dungeon-Installer installed

    time to generate a new key of SVC 30

    SVC generate a new method ssl key

    SVC request no svc default

    username password asdm privilege Yvx83jxa2WCRAZ/m number 15

    hajo 2w8CnP1hHKVozsC1 encrypted password username

    hajo attributes username

    type of remote access service

    tunnel-group 192.168.178.230 type ipsec-l2l

    IPSec-attributes tunnel-group 192.168.178.230

    pre-shared-key *.

    type tunnel-group SSLClientProfile remote access

    attributes global-tunnel-group SSLClientProfile

    Group Policy - by default-SSLClientPolicy

    tunnel-group SSLClientProfile webvpn-attributes

    enable SSLVPNClient group-alias

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns preset_dns_map

    parameters

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the preset_dns_map dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the netbios

    inspect the rsh

    inspect the rtsp

    inspect the skinny

    inspect esmtp

    inspect sqlnet

    inspect sunrpc

    inspect the tftp

    inspect the sip

    inspect xdmcp

    !

    global service-policy global_policy

    context of prompt hostname

    Cryptochecksum:0008564b545500650840cf27eb06b957

    : end

    What wrong with my setup.

    Concerning

    Hans-Jürgen Guenter

    Hello Hans,.

    You should change your VPN pool to be a different subnet within the network, for example: 192.168.5.0/24

    Then configure NAT exemption for traffic between the Interior and the pool of vpn.

    Based on your current configuration, the following changes:

    mask 192.168.5.10 - 192.168.5.15 255.255.255.0 IP local pool SSLClientPool

    no_NAT to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0

    And then also to enable icmp inspection:

    Policy-map global_policy

    class inspection_default

    inspect the icmp

  • VPN connects but cannot ping or access resources

    I hope this is an easy fix and it's something that I am missing.  I've been looking at this for several hours.

    Scenario:

    I Anyconnect Essentials so I use the SSL connection

    I changed my domain name and external IP in my setup, I write.

    My VPN connection seems to work very well.  In fact, I was able to connect to 3 locations with 3 different external IP address.

    1 location, I get IP address 192.168.30.10, as it should.  I can ping 192.168.1.1, but not the 192.168.1.6 which is my temporary resource, the firewall is disabled on 192.168.1.6.

    2 location, I get an IP of 192.168.30.11, as it should.  I was able to ping 192.168.30.10, could not sue 192.168.1.1 as the place closed.

    Any help would be appreciated, it's getting late so I hope I gave enough details.  I feel so close but yet so far.

    See the ciscoasa # running

    : Saved

    :

    ASA Version 8.2 (1)

    !

    ciscoasa hostname

    names of

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 192.168.1.1 255.255.255.0

    !

    interface Vlan2

    nameif outside

    security-level 0

    IP 22.22.22.246 255.255.255.252

    !

    interface Ethernet0/0

    switchport access vlan 2

    !

    interface Ethernet0/1

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    passive FTP mode

    clock timezone CST - 6

    clock to summer time recurring CDT

    DNS lookup field inside

    DNS domain-lookup outside

    permit same-security-traffic inter-interface

    permit same-security-traffic intra-interface

    ICMP-type of object-group ALLOWPING

    echo ICMP-object

    ICMP-object has exceeded the time

    response to echo ICMP-object

    Object-ICMP traceroute

    Object-ICMP source-quench

    ICMP-unreachable object

    access-list 10 scope ip allow a whole

    10 extended access-list allow icmp a whole

    pager lines 24

    asdm of logging of information

    Within 1500 MTU

    Outside 1500 MTU

    mask 192.168.30.10 - 192.168.30.25 255.255.255.0 IP local pool SSLClientPoolNew

    ICMP unreachable rate-limit 1 burst-size 1

    don't allow no asdm history

    ARP timeout 14400

    Global 1 interface (outside)

    NAT (inside) 1 192.168.1.0 255.255.255.0

    Route outside 0.0.0.0 0.0.0.0 22.22.22.245 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    dynamic-access-policy-registration DfltAccessPolicy

    network-acl 10

    WebVPN

    SVC request no svc default

    AAA authentication LOCAL telnet console

    Enable http server

    http 192.168.1.0 255.255.255.0 inside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    Telnet 0.0.0.0 0.0.0.0 inside

    Telnet timeout 5

    SSH timeout 5

    Console timeout 0

    management-access inside

    dhcpd dns 8.8.8.8

    dhcpd outside auto_config

    !

    dhcpd address 192.168.1.5 - 192.168.1.36 inside

    dhcpd allow inside

    !

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    allow inside

    allow outside

    AnyConnect essentials

    SVC disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 1 image

    SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 2 image

    enable SVC

    tunnel-group-list activate

    internal SSLClientPolicy group strategy

    attributes of Group Policy SSLClientPolicy

    Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

    field default value mondomaine.fr

    the address value SSLClientPoolNew pools

    WebVPN

    SVC Dungeon-Installer installed

    time to generate a new key of SVC 180

    SVC generate a new method ssl key

    SVC value vpngina modules

    attributes of Group Policy DfltGrpPolicy

    VPN-tunnel-Protocol webvpn

    username test encrypted password privilege 15 xxxxxxxxxxxxxx

    username ljb1 password encrypted xxxxxxxxxxxxxx

    type tunnel-group SSLClientProfile remote access

    attributes global-tunnel-group SSLClientProfile

    Group Policy - by default-SSLClientPolicy

    tunnel-group SSLClientProfile webvpn-attributes

    enable SSLVPNClient group-alias

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    Policy-map global_policy

    class inspection_default

    inspect the icmp

    !

    global service-policy global_policy

    context of prompt hostname

    Cryptochecksum:ed683c7f1b86066d1d8c4fff6b08c592

    : end

    Patrick,

    'Re missing you the excemption NAT. Please add the following and try again:

    access-list allowed sheep ip 192.168.1.0 255.255.255.0 192.168.30.0 255.255.255.0

    NAT (inside) 0 access-list sheep

    Let us know if you still have problems after that.

    Raga

  • My laptop connects is more to the internet, either hard wired or wireless. When it is hard wired, the laptop displays connection but I can't access the internet, and I've done it before.

    My laptop connects is more to the internet, either hard wired or wireless.  When it is hard wired, the laptop displays connection but I can't access the internet, and I've done it before.  My other computer has service very well (or I wouldn't send this message) I checked everything, what to do?

    original title: internet connection.

    Hi vonhatten,

    1. Did you the latest changes on the computer?
    2. You receive an error message when you try to connect to the internet?
    3. You have security software installed on the computer?

    Refer to the article below and try the steps mentioned, check if it helps.

    In Windows network connection issues

    http://support.Microsoft.com/kb/313242

  • I am trying to create a VPN connection, but when I get to the step that allows me to create the VPN, the radial buttons are greyed out.

    I am trying to create a VPN connection, but when I get to the step that allows me to create the VPN, the radial buttons are grayed out, it is a Windows component is missing and does not allow me to create VPN. I am running Windows XP Home addition. I recently got a Malware attack and had the quarantine and fix trojen attempts. After the restoration, I found that my previous VPN connection was broken. When I tried to add a new connection, I'm stuck on the screen connection virtual network in the the radial button private network connection wizard is grayed out, he could not check.

    Hello

    Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Windows XP TechNet forum. You can follow the link to your question:

    http://social.technet.Microsoft.com/forums/en/itproxpsp/threads

  • I am trying to create a VPN connection, but it does not work

    I am trying to create a VPN connection, but it does not work
    The wizard cannot establish a connection. And if I try to record simply does not connect
    It does not work. If I try to click on find the problem, there simply
    do nothing.
    I tried it on another pc, where it worked. So the problem is not the
    router or data network. And the curious thing is that I installed it before, but only from one day to the other, the VPN connection was missing.

    It does not create even a the connection icon
    Thank you

    Try a system restore to a Date before the problem began:

    Restore point:

    http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

    Do Safe Mode system restore, if it is impossible to do in Normal Mode.

    Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

    Try a restore of the system once, to choose a Restore Point prior to your problem...

    Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

    http://www.windowsvistauserguide.com/system_restore.htm

    Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

    See you soon.

    Mick Murphy - Microsoft partner

  • I created a vpn connection, but can I create a shortcut to connect every time?

    I created a vpn connection, but can I create a shortcut to connect every time?

    I created a vpn connection, but can I create a shortcut to connect every time?

    Open network and sharing Center, go to the Edit card settings window and drag the VPN icon on your desktop.

  • Cisco ipsec Vpn connects but cannot communicate with lan

    I have a version of cisco 1921 15.2 (4) M3 I install vpn ipsec and may have customers to connect but cannot ping anything inside.  A glimpse of what could be wrong with my config would be greatly appreciated.  I posted the configuration as well as running a few outings of ipsec.  I also tried with multiple operating systems using cisco vpn client and shrewsoft.  I am able to connect to the other VPN ipsec running 1921 both of these computers by using a client.

    Thanks for any assistance

    SH run

    !
    AAA new-model
    !
    !
    AAA authentication login radius_auth local radius group
    connection of AAA VPN_AUTHEN group local RADIUS authentication
    AAA authorization network_vpn_author LAN
    !
    !
    !
    !
    !
    AAA - the id of the joint session
    clock timezone PST - 8 0
    clock to summer time recurring PST
    !
    no ip source route
    decline of the IP options
    IP cef
    !
    !
    !
    !
    !
    !
    no ip bootp Server
    no ip domain search
    domain IP XXX.local
    inspect the high IP 3000 max-incomplete
    inspect the low IP 2800 max-incomplete
    IP inspect a low minute 2800
    IP inspect a high minute 3000
    inspect the IP icmp SDM_LOW name
    inspect the IP name SDM_LOW esmtp
    inspect the tcp IP SDM_LOW name
    inspect the IP udp SDM_LOW name
    IP inspect name SDM_LOW ssh
    No ipv6 cef
    !
    Authenticated MultiLink bundle-name Panel
    !
    !
    Crypto pki trustpoint TP-self-signed-2909270577
    enrollment selfsigned
    name of the object cn = IOS - Self - signed - certificate - 2909270577
    revocation checking no
    rsakeypair TP-self-signed-2909270577
    !
    !
    TP-self-signed-2909270577 crypto pki certificate chain
    certificate self-signed 01
    license udi pid CISCO1921/K9 sn FTX1715818R
    !
    !
    Archives
    The config log
    Enable logging
    size of logging 1000
    notify the contenttype in clear syslog
    the ADMIN_HOSTS object-group network
    71.X.X.X 71.X.X.X range
    !
    name of user name1 secret privilege 15 4 XXXXXXX

    !
    redundancy
    !
    !
    !
    !
    !
    property intellectual ssh time 60
    property intellectual ssh authentication-2 retries
    property intellectual ssh event logging
    property intellectual ssh version 2
    !
    !
    crypto ISAKMP policy 1
    BA 3des
    preshared authentication
    Group 2
    !
    ISAKMP crypto client configuration group roaming_vpn
    key XXXXX
    DNS 192.168.10.10 10.1.1.1
    XXX.local field
    pool VPN_POOL_1
    ACL client_vpn_traffic
    netmask 255.255.255.0
    !
    !
    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
    tunnel mode
    !
    !
    !
    crypto dynamic-map VPN_DYNMAP_1 1
    Set the security association idle time 1800
    game of transformation-ESP-3DES-SHA
    market arriere-route
    !
    !
    list of authentication of card crypto SDM_CMAP_1 client VPN_AUTHEN
    map SDM_CMAP_1 isakmp authorization list network_vpn_author crypto
    client configuration address map SDM_CMAP_1 crypto answer
    map SDM_CMAP_1 65535-isakmp dynamic VPN_DYNMAP_1 ipsec crypto
    !
    !
    !
    !
    !
    the Embedded-Service-Engine0/0 interface
    no ip address
    Shutdown
    !
    interface GigabitEthernet0/0
    IP 76.W.E.R 255.255.255.248
    IP access-group ATT_Outside_In in
    no ip redirection
    no ip unreachable
    no ip proxy-arp
    NAT outside IP
    inspect the SDM_LOW over IP
    IP virtual-reassembly in
    load-interval 30
    automatic duplex
    automatic speed
    No cdp enable
    No mop enabled
    map SDM_CMAP_1 crypto
    !
    interface GigabitEthernet0/1
    no ip address
    load-interval 30
    automatic duplex
    automatic speed
    !
    interface GigabitEthernet0/1.10
    encapsulation dot1Q 1 native
    IP 192.168.10.1 255.255.255.0
    no ip redirection
    no ip unreachable
    no ip proxy-arp
    property intellectual accounting-access violations
    IP nat inside
    IP virtual-reassembly in
    !
    interface GigabitEthernet0/1.100
    encapsulation dot1Q 100
    10.1.1.254 IP address 255.255.255.0
    no ip redirection
    no ip unreachable
    no ip proxy-arp
    IP nat inside
    IP virtual-reassembly in
    !
    interface GigabitEthernet0/1,200
    encapsulation dot1Q 200
    IP 10.1.2.254 255.255.255.0
    no ip redirection
    no ip unreachable
    no ip proxy-arp
    IP nat inside
    IP virtual-reassembly in
    IP tcp adjust-mss 1452
    !
    local IP VPN_POOL_1 192.168.168.193 pool 192.168.168.254
    IP forward-Protocol ND
    !
    IP http server
    IP http authentication aaa-authentication of connection ADMIN_AUTHEN
    IP http secure server
    IP http timeout policy slowed down 60 life 86400 request 10000
    !
    IP nat inside source map route ATT_NAT_LIST interface GigabitEthernet0/0 overload
    IP nat inside source static tcp 192.168.10.10 25 expandable 25 76.W.E.R
    IP nat inside source static tcp 192.168.10.10 80 76.W.E.R 80 extensible
    IP nat inside source static tcp 192.168.10.10 76.W.E.R expandable 443 443
    IP nat inside source static tcp 192.168.10.10 76.W.E.R expandable 987 987
    IP route 0.0.0.0 0.0.0.0 76.W.E.F
    !
    ATT_Outside_In extended IP access list
    permit tcp object-group ADMIN_HOSTS any eq 22
    allow any host 76.W.E.R eq www tcp
    allow any host 76.W.E.R eq 443 tcp
    allow 987 tcp any host 76.W.E.R eq
    allow any host 76.W.E.R eq tcp smtp
    permit any any icmp echo response
    allow icmp a whole
    allow udp any any eq isakmp
    allow an esp
    allow a whole ahp
    permit any any eq non500-isakmp udp
    deny ip 10.0.0.0 0.255.255.255 everything
    deny ip 172.16.0.0 0.15.255.255 all
    deny ip 192.168.0.0 0.0.255.255 everything
    deny ip 127.0.0.0 0.255.255.255 everything
    refuse the ip 255.255.255.255 host everything
    refuse the host ip 0.0.0.0 everything
    NAT_LIST extended IP access list
    IP 10.1.0.0 allow 0.0.255.255 everything
    permit ip 192.168.10.0 0.0.0.255 any
    deny ip 192.168.10.0 0.0.0.255 192.168.168.192 0.0.0.63
    refuse the 10.1.1.0 ip 0.0.0.255 192.168.168.192 0.0.0.63
    deny ip 10.1.2.0 0.0.0.255 192.168.168.192 0.0.0.63
    client_vpn_traffic extended IP access list
    permit ip 192.168.10.0 0.0.0.255 192.168.168.192 0.0.0.63
    ip licensing 10.1.1.0 0.0.0.255 192.168.168.192 0.0.0.63
    IP 10.1.2.0 allow 0.0.0.255 10.1.1.0 0.0.0.255
    !
    radius of the IP source-interface GigabitEthernet0/1.10
    Logging trap errors
    logging source hostname id
    logging source-interface GigabitEthernet0/1.10
    !
    ATT_NAT_LIST allowed 20 route map
    corresponds to the IP NAT_LIST
    is the interface GigabitEthernet0/0
    !
    !
    SNMP-server community [email protected] / * /! s RO
    Server enable SNMP traps snmp authentication linkdown, linkup warmstart cold start
    Server enable SNMP traps vrrp
    Server SNMP enable transceiver traps all the
    Server enable SNMP traps ds1
    Enable SNMP-Server intercepts the message-send-call failed remote server failure
    Enable SNMP-Server intercepts ATS
    Server enable SNMP traps eigrp
    Server enable SNMP traps ospf-change of State
    Enable SNMP-Server intercepts ospf errors
    SNMP Server enable ospf retransmit traps
    Server enable SNMP traps ospf lsa
    Server enable SNMP traps ospf nssa-trans-changes state cisco-change specific
    SNMP server activate interface specific cisco-ospf traps shamlink state change
    SNMP Server enable neighbor traps cisco-specific ospf to the State shamlink change
    Enable SNMP-Server intercepts specific to cisco ospf errors
    SNMP server activate specific cisco ospf retransmit traps
    Server enable SNMP traps ospf cisco specific lsa
    SNMP server activate license traps
    Server enable SNMP traps envmon
    traps to enable SNMP-Server ethernet cfm cc mep-top low-mep Dispatcher loop config
    Enable SNMP-Server intercepts ethernet cfm overlap missing mep mep-unknown service-up
    Server enable SNMP traps auth framework sec-violation
    Server enable SNMP traps c3g
    entity-sensor threshold traps SNMP-server enable
    Server enable SNMP traps adslline
    Server enable SNMP traps vdsl2line
    Server enable SNMP traps icsudsu
    Server enable SNMP traps ISDN call-information
    Server enable SNMP traps ISDN layer2
    Server enable SNMP traps ISDN chan-not-available
    Server enable SNMP traps ISDN ietf
    Server enable SNMP traps ds0-busyout
    Server enable SNMP traps ds1-loopback
    SNMP-Server enable traps energywise
    Server enable SNMP traps vstack
    SNMP traps enable mac-notification server
    Server enable SNMP traps bgp cbgp2
    Enable SNMP-Server intercepts isis
    Server enable SNMP traps ospfv3-change of State
    Enable SNMP-Server intercepts ospfv3 errors
    Server enable SNMP traps aaa_server
    Server enable SNMP traps atm subif
    Server enable SNMP traps cef resources-failure-change of State peer peer-fib-state-change inconsistency
    Server enable SNMP traps memory bufferpeak
    Server enable SNMP traps cnpd
    Server enable SNMP traps config-copy
    config SNMP-server enable traps
    Server enable SNMP traps config-ctid
    entity of traps activate SNMP Server
    Server enable SNMP traps fru-ctrl
    SNMP traps-policy resources enable server
    Server SNMP enable traps-Manager of event
    Server enable SNMP traps frames multi-links bundle-incompatibility
    SNMP traps-frame relay enable server
    Server enable SNMP traps subif frame relay
    Server enable SNMP traps hsrp
    Server enable SNMP traps ipmulticast
    Server enable SNMP traps msdp
    Server enable SNMP traps mvpn
    Server enable SNMP traps PNDH nhs
    Server enable SNMP traps PNDH nhc
    Server enable SNMP traps PNDH PSN
    Server enable SNMP traps PNDH exceeded quota
    Server enable SNMP traps pim neighbor-rp-mapping-change invalid-pim-message of change
    Server enable SNMP traps pppoe
    Enable SNMP-server holds the CPU threshold
    SNMP Server enable rsvp traps
    Server enable SNMP traps syslog
    Server enable SNMP traps l2tun session
    Server enable SNMP traps l2tun pseudowire status
    Server enable SNMP traps vtp
    Enable SNMP-Server intercepts waas
    Server enable SNMP traps ipsla
    Server enable SNMP traps bfd
    Server enable SNMP traps gdoi gm-early-registration
    Server enable SNMP traps gdoi full-save-gm
    Server enable SNMP traps gdoi gm-re-register
    Server enable SNMP traps gdoi gm - generate a new key-rcvd
    Server enable SNMP traps gdoi gm - generate a new key-fail
    Server enable SNMP traps gdoi ks - generate a new key-pushed
    Enable SNMP traps gdoi gm-incomplete-cfg Server
    Enable SNMP-Server intercepts gdoi ks-No.-rsa-keys
    Server enable SNMP traps gdoi ks-new-registration
    Server enable SNMP traps gdoi ks-reg-complete
    Enable SNMP-Server Firewall state of traps
    SNMP-Server enable traps ike policy add
    Enable SNMP-Server intercepts removal of ike policy
    Enable SNMP-Server intercepts start ike tunnel
    Enable SNMP-Server intercepts stop ike tunnel
    SNMP server activate ipsec cryptomap add traps
    SNMP server activate ipsec cryptomap remove traps
    SNMP server activate ipsec cryptomap attach traps
    SNMP server activate ipsec cryptomap detach traps
    Server SNMP traps enable ipsec tunnel beginning
    SNMP-Server enable traps stop ipsec tunnel
    Enable SNMP-server holds too many associations of ipsec security
    Enable SNMP-Server intercepts alarm ethernet cfm
    Enable SNMP-Server intercepts rf
    Server enable SNMP traps vrfmib vrf - up low-vrf vnet-trunk-up low-trunk-vnet
    Server RADIUS dead-criteria life 2
    RADIUS-server host 192.168.10.10
    Server RADIUS 2 timeout
    Server RADIUS XXXXXXX key
    !
    !
    !
    control plan
    !
    !

    Line con 0
    privilege level 15
    connection of authentication radius_auth
    line to 0
    line 2
    no activation-character
    No exec
    preferred no transport
    transport of entry all
    transport output pad rlogin lapb - your MOP v120 udptn ssh telnet
    StopBits 1
    line vty 0 4
    privilege level 15
    connection of authentication radius_auth
    entry ssh transport
    line vty 5 15
    privilege level 15
    connection of authentication radius_auth
    entry ssh transport
    !
    Scheduler allocate 20000 1000
    NTP-Calendar Update
    Server NTP 192.168.10.10
    NTP 64.250.229.100 Server
    !
    end

    Router ipsec crypto #sh her

    Interface: GigabitEthernet0/0
    Tag crypto map: SDM_CMAP_1, local addr 76.W.E.R

    protégé of the vrf: (none)
    local ident (addr, mask, prot, port): (0.0.0.0/0.0.0.0/0/0)
    Remote ident (addr, mask, prot, port): (192.168.168.213/255.255.255.255/0/0)
    current_peer 75.X.X.X port 2642
    LICENCE, flags is {}
    #pkts program: 1953, #pkts encrypt: 1953, #pkts digest: 1953
    #pkts decaps: 1963, #pkts decrypt: 1963, #pkts check: 1963
    compressed #pkts: 0, unzipped #pkts: 0
    #pkts uncompressed: 0, #pkts compr. has failed: 0
    #pkts not unpacked: 0, #pkts decompress failed: 0
    Errors #send 0, #recv 0 errors

    local crypto endpt. : 76.W.E.R, remote Start crypto. : 75.X.X.X
    Path mtu 1500, mtu 1500 ip, ip mtu IDB GigabitEthernet0/0
    current outbound SPI: 0x5D423270 (1564619376)
    PFS (Y/N): N, Diffie-Hellman group: no

    SAS of the esp on arrival:
    SPI: 0x2A5177DD (709982173)
    transform: esp-3des esp-sha-hmac.
    running parameters = {Tunnel UDP-program}
    Conn ID: 2115, flow_id: VPN:115 on board, sibling_flags 80000040, crypto card: SDM_CMAP_1
    calendar of his: service life remaining (k/s) key: (4301748/2809)
    Size IV: 8 bytes
    support for replay detection: Y
    Status: ACTIVE (ACTIVE)

    the arrival ah sas:

    SAS of the CFP on arrival:

    outgoing esp sas:
    SPI: 0x5D423270 (1564619376)
    transform: esp-3des esp-sha-hmac.
    running parameters = {Tunnel UDP-program}
    Conn ID: 2116, flow_id: VPN:116 on board, sibling_flags 80000040, crypto card: SDM_CMAP_1
    calendar of his: service life remaining (k/s) key: (4301637/2809)
    Size IV: 8 bytes
    support for replay detection: Y
    Status: ACTIVE (ACTIVE)

    outgoing ah sas:

    outgoing CFP sas:

    Routing crypto isakmp #sh its
    IPv4 Crypto ISAKMP Security Association
    DST CBC conn-State id
    76.W.E.R 75.X.X.X QM_IDLE 1055 ACTIVE

    IPv6 Crypto ISAKMP Security Association

    In your acl, nat, you will need to refuse your VPN traffic before you allow the subnet at all. Just put all the declarations of refusal before the declarations of licence.

    Sent by Cisco Support technique iPhone App

  • ASA 5505 IPSEC VPN connected but cannot access the local network

    ASA: 8.2.5

    ASDM: 6.4.5

    LAN: 10.1.0.0/22

    Pool VPN: 172.16.10.0/24

    Hi, we purcahsed a new ASA 5505 and try to configure IPSEC VPN via ASDM; I simply run the wizards, installation vpnpool, split tunnelling, etc.

    I can connect to the ASA using the cisco VPN client and internet works fine on the local PC, but it can not access the local network (can not impossible. ping remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile, I created worked very well.

    Here is my setup, wrong set up anything?

    ASA Version 8.2 (5)

    !

    hostname asatest

    domain XXX.com

    activate 8Fw1QFqthX2n4uD3 encrypted password

    g9NiG6oUPjkYrHNt encrypted passwd

    names of

    !

    interface Ethernet0/0

    switchport access vlan 2

    !

    interface Ethernet0/1

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 10.1.1.253 255.255.252.0

    !

    interface Vlan2

    nameif outside

    security-level 0

    address IP XXX.XXX.XXX.XXX 255.255.255.240

    !

    passive FTP mode

    clock timezone PST - 8

    clock summer-time recurring PDT

    DNS server-group DefaultDNS

    domain vff.com

    vpntest_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.252.0

    access extensive list ip 10.1.0.0 inside_nat0_outbound allow 255.255.252.0 172.16.10.0 255.255.255.0

    pager lines 24

    Enable logging

    timestamp of the record

    logging trap warnings

    asdm of logging of information

    logging - the id of the device hostname

    host of logging inside the 10.1.1.230

    Within 1500 MTU

    Outside 1500 MTU

    IP local pool 172.16.10.1 - 172.16.10.254 mask 255.255.255.0 vpnpool

    no failover

    ICMP unreachable rate-limit 1 burst-size 1

    don't allow no asdm history

    ARP timeout 14400

    Global 1 interface (outside)

    NAT (inside) 0-list of access inside_nat0_outbound

    NAT (inside) 1 0.0.0.0 0.0.0.0

    Route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    Floating conn timeout 0:00:00

    dynamic-access-policy-registration DfltAccessPolicy

    AAA-server protocol nt AD

    AAA-server host 10.1.1.108 AD (inside)

    NT-auth-domain controller 10.1.1.108

    Enable http server

    http 10.1.0.0 255.255.252.0 inside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

    Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    outside_map interface card crypto outside

    crypto ISAKMP allow outside

    crypto ISAKMP policy 10

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    Telnet timeout 5

    SSH 10.1.0.0 255.255.252.0 inside

    SSH timeout 20

    Console timeout 0

    dhcpd outside auto_config

    !

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    internal group vpntest strategy

    Group vpntest policy attributes

    value of 10.1.1.108 WINS server

    Server DNS 10.1.1.108 value

    Protocol-tunnel-VPN IPSec l2tp ipsec

    disable the password-storage

    disable the IP-comp

    Re-xauth disable

    disable the PFS

    IPSec-udp disable

    IPSec-udp-port 10000

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list vpntest_splitTunnelAcl

    value by default-domain XXX.com

    disable the split-tunnel-all dns

    Dungeon-client-config backup servers

    the address value vpnpool pools

    admin WeiepwREwT66BhE9 encrypted privilege 15 password username

    username user5 encrypted password privilege 5 yIWniWfceAUz1sUb

    the encrypted password privilege 3 umNHhJnO7McrLxNQ util_3 username

    tunnel-group vpntest type remote access

    tunnel-group vpntest General attributes

    address vpnpool pool

    authentication-server-group AD

    authentication-server-group (inside) AD

    Group Policy - by default-vpntest

    band-Kingdom

    vpntest group tunnel ipsec-attributes

    pre-shared-key BEKey123456

    NOCHECK Peer-id-validate

    !

    !

    privilege level 3 mode exec cmd command perfmon

    privilege level 3 mode exec cmd ping command

    mode privileged exec command cmd level 3

    logging of the privilege level 3 mode exec cmd commands

    privilege level 3 exec command failover mode cmd

    privilege level 3 mode exec command packet cmd - draw

    privilege show import at the level 5 exec mode command

    privilege level 5 see fashion exec running-config command

    order of privilege show level 3 exec mode reload

    privilege level 3 exec mode control fashion show

    privilege see the level 3 exec firewall command mode

    privilege see the level 3 exec mode command ASP.

    processor mode privileged exec command to see the level 3

    privilege command shell see the level 3 exec mode

    privilege show level 3 exec command clock mode

    privilege exec mode level 3 dns-hosts command show

    privilege see the level 3 exec command access-list mode

    logging of orders privilege see the level 3 exec mode

    privilege, level 3 see the exec command mode vlan

    privilege show level 3 exec command ip mode

    privilege, level 3 see fashion exec command ipv6

    privilege, level 3 see the exec command failover mode

    privilege, level 3 see fashion exec command asdm

    exec mode privilege see the level 3 command arp

    command routing privilege see the level 3 exec mode

    privilege, level 3 see fashion exec command ospf

    privilege, level 3 see the exec command in aaa-server mode

    AAA mode privileged exec command to see the level 3

    privilege, level 3 see fashion exec command eigrp

    privilege see the level 3 exec mode command crypto

    privilege, level 3 see fashion exec command vpn-sessiondb

    privilege level 3 exec mode command ssh show

    privilege, level 3 see fashion exec command dhcpd

    privilege, level 3 see the vpnclient command exec mode

    privilege, level 3 see fashion exec command vpn

    privilege level see the 3 blocks from exec mode command

    privilege, level 3 see fashion exec command wccp

    privilege see the level 3 exec command mode dynamic filters

    privilege, level 3 see the exec command in webvpn mode

    privilege control module see the level 3 exec mode

    privilege, level 3 see fashion exec command uauth

    privilege see the level 3 exec command compression mode

    level 3 for the show privilege mode configure the command interface

    level 3 for the show privilege mode set clock command

    level 3 for the show privilege mode configure the access-list command

    level 3 for the show privilege mode set up the registration of the order

    level 3 for the show privilege mode configure ip command

    level 3 for the show privilege mode configure command failover

    level 5 mode see the privilege set up command asdm

    level 3 for the show privilege mode configure arp command

    level 3 for the show privilege mode configure the command routing

    level 3 for the show privilege mode configure aaa-order server

    level mode 3 privilege see the command configure aaa

    level 3 for the show privilege mode configure command crypto

    level 3 for the show privilege mode configure ssh command

    level 3 for the show privilege mode configure command dhcpd

    level 5 mode see the privilege set privilege to command

    privilege level clear 3 mode exec command dns host

    logging of the privilege clear level 3 exec mode commands

    clear level 3 arp command mode privileged exec

    AAA-server of privilege clear level 3 exec mode command

    privilege clear level 3 exec mode command crypto

    privilege clear level 3 exec command mode dynamic filters

    level 3 for the privilege cmd mode configure command failover

    clear level 3 privilege mode set the logging of command

    privilege mode clear level 3 Configure arp command

    clear level 3 privilege mode configure command crypto

    clear level 3 privilege mode configure aaa-order server

    context of prompt hostname

    no remote anonymous reporting call

    Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4

    : end

    Captures we can see packets going from the pool to the internal LAN, but we do not reply back packages.

    The routing must be such that for 172.16.10.0/24 packages should reach the inside interface of the ASA.

    On client machines or your internal LAN switch, you need to add route for 172.16.10.0/24 pointing to the inside interface of the ASA.

  • VPN client connected but no ping nor access to privat network

    Hello

    I have a 1802w installed, a VPN client that can connect to the router and L2L connection, which works very well.

    On the router, I see that the client is connected, but no traffic passes. In sh crypto ipsec, I see that traffic is decrypted, but no packtets are encypted.

    Can someone point me in the right direction? I have the confs and debugs attached. Thanks for the help in advance.

    Erich

    Erich,

    Looking at your configuration, two things:

    1 - is the current running configuration. I see your Tunnel L2L is configured with an address of correspondence of 101, but I don't see a 101 ACL set on the router.

    2. your Split Tunnel must be reconfigured. Which means, the source and destination must be exchanged.

    SplitList extended IP access list

    permit ip 192.168.2.0 0.0.0.255 192.168.111.0 0.0.0.255

    Split Tunneling

    http://www.Cisco.com/en/us/Tech/tk59/technologies_configuration_example09186a00800a393b.shtml#Con4

    Also, the IP address pool you assign to clients, ensure that they are not part of a LAN on your side. If so, you can then run in routing problems.

    Kind regards

    Arul

    * Please note all useful messages *.

  • VPN connects but can't access internal devices

    Thanks in advance for any help that can be provided.

    I use AnyConnect to create a VPN with an ASA 5505.  Once connected, the client needs to access a device behind a router in 1941.

    Internally, (without using VPN), all my itinerary runs correctly.  My VPN client can connect and when I put a route on my router from 1941, I am able to ping this particular device.  But my VPN client cannot appear ping all the remaining devices on the same internal range as the ASA 5505 or whatever happened on 1941.

    Device far router VPN Client ASA 5505 1941 Workstation

    192.168.201.20---> outside IP x.x.x.x / / internal 192.168.101.1 192.168.101.56 192.168.101.2 / / 192.168.8.1 192.168.8.150

    Client connects and get the IP address of the ASA

    Cannot ping it cannot ping

    Can ping the internal IP address of 1941

    * (after creating a static route)

    I was playing with my setup intensively to try to make this work.  Split tunneling is enabled and is required.

    Here is my current config:

    hostnameMYHOST

    activate mUUvr2NINofYuSh2 encrypted password

    UNDrnIuGV0tAPtz2 encrypted passwd

    names of

    !

    interface Ethernet0/0

    switchport access vlan 2

    !

    interface Ethernet0/1

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    switchport access vlan 7

    !

    interface Vlan1

    nameif inside

    security-level 100

    192.168.101.1 IP address 255.255.255.0

    !

    interface Vlan2

    nameif outside

    security-level 0

    IP x.x.x.x 255.255.0.0

    !

    interface Vlan7

    prior to interface Vlan1

    nameif DMZ

    security-level 20

    IP 137.57.183.1 255.255.255.0

    !

    passive FTP mode

    clock timezone STD - 7

    DNS domain-lookup outside

    the obj_any_dmz object-group network

    192.168.101.0 IP Access-list extended sheep 255.255.255.0 allow all

    192.168.201.0 IP Access-list extended sheep 255.255.255.0 allow all

    tunneling split list of permitted access standard 192.168.101.0 255.255.255.0

    pager lines 24

    Enable logging

    debug logging in buffered memory

    asdm of logging of information

    Within 1500 MTU

    Outside 1500 MTU

    MTU 1500 DMZ

    mask 192.168.101.125 - 192.168.101.130 255.255.255.0 IP local pool Internal_Range

    IP local pool vpn_pool 192.168.201.20 - 192.168.201.30 mask 255.255.255.0

    ICMP unreachable rate-limit 1 burst-size 1

    don't allow no asdm history

    ARP timeout 14400

    Global interface 10 (external)

    NAT (inside) 0 access-list sheep

    NAT (inside) 1 0.0.0.0 0.0.0.0

    NAT (DMZ) 10 137.57.183.0 255.255.255.0

    Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

    Route inside 192.168.8.0 255.255.255.0 192.168.101.2 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    Floating conn timeout 0:00:00

    dynamic-access-policy-registration DfltAccessPolicy

    the ssh LOCAL console AAA authentication

    http server enable 64000

    http 0.0.0.0 0.0.0.0 inside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    Crypto ca trustpoint ASDM_TrustPoint1

    registration auto

    name of the object CN = MYHOST

    ClientX_cert key pair

    Configure CRL

    string encryption ca ASDM_TrustPoint1 certificates

    certificate 0f817951

    308201e7 a0030201 30820150 0202040f 0d06092a 81795130 864886f7 0d 010105

    05003038 31173015 06035504 03130e41 494d452d 56504e2d 42415455 53311d 30

    1b06092a 864886f7 0d 010902 160e4149 4d452d56 504e2d42 41545553 301e170d

    31333036 32373137 32393335 5a170d32 33303632 35313732 3933355a 30383117

    30150603 55040313 0e41494d 452-5650 4e2d4241 54555331 1d301b06 092 d has 8648

    86f70d01 0902160e 41494d 45 2d56504e 424154 55533081 9f300d06 092 2d has 8648

    86f70d01 01010500 03818d 30818902 00 818100c 9 ff840bf4 cfb8d394 2 c 940430

    1887f25a 49038aa0 1299cf10 bda2a436 227dcdbf f1c5566b c35c2f19 8b3514d3

    4e24f5b1 c8840e8c 60e2b39d bdc0082f 08cce525 97ffefba d42bb087 81b9adb9

    db0a8b2f b643e651 d17cd6f8 f67297f2 d785ef46 c3acbb39 615e1ef1 23db072c

    783fe112 acd6dc80 dc38e94b 6e56fe94 d59d5d02 03010001 300 d 0609 2a 864886

    8181007e f70d0101 05050003 29e90ea0 e337976e 9006bc02 402fd58a a1d30fe8

    b2c1ab49 a1828ee0 488d1d2f 1dc5d150 3ed85f09 54f099b2 064cd 622 dc3d3821

    fca46c69 62231fd2 6e396cd1 7ef586f9 f41205af c2199174 3c5ee887 42b684c9

    7f4d2045 4742adb5 d70c3805 4ad13191 8d802bbc b2bcd8c7 8eec111b 761d89f3

    63ebd49d 30dd06f4 e0fa25

    quit smoking

    crypto ISAKMP allow outside

    crypto ISAKMP policy 40

    preshared authentication

    aes-256 encryption

    sha hash

    Group 5

    life 86400

    Telnet timeout 5

    SSH 0.0.0.0 0.0.0.0 inside

    SSH 0.0.0.0 0.0.0.0 DMZ

    SSH timeout 10

    Console timeout 0

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    SSL encryption rc4 - md5, rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1

    SSL-trust outside ASDM_TrustPoint1 point

    WebVPN

    allow outside

    SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 1 image

    enable SVC

    internal ClientX_access group strategy

    attributes of Group Policy ClientX_access

    4.2.2.2 DNS server value

    VPN-tunnel-Protocol svc

    Split-tunnel-policy tunnelspecified

    Split-tunnel-network-list value split tunneling

    access.local value by default-field

    the address value vpn_pool pools

    IPv6 address pools no

    WebVPN

    SVC mtu 1406

    generate a new key SVC time no

    SVC generate a new method ssl key

    username privilege 15 encrypted password ykAxQ227nzontdIh ClientX

    ClientX username attributes

    VPN-group-policy ClientX_access

    type of service admin

    tunnel-group ClientX type remote access

    attributes global-tunnel-group ClientX

    address pool Internal_Range

    Group Policy - by default-ClientX_access

    type tunnel-group SSLClientProfile remote access

    attributes global-tunnel-group SSLClientProfile

    Group Policy - by default-ClientX_access

    type tunnel-group ClientX_access remote access

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns preset_dns_map

    parameters

    maximum message length automatic of customer

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the preset_dns_map dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the rsh

    inspect the rtsp

    inspect esmtp

    inspect sqlnet

    inspect the skinny

    inspect sunrpc

    inspect xdmcp

    inspect the sip

    inspect the netbios

    inspect the tftp

    Review the ip options

    !

    global service-policy global_policy

    context of prompt hostname

    no remote anonymous reporting call

    Cryptochecksum:da38065247f7334a5408b7ada3af29ae

    : end

    OK, lets go on... ;-)

    Split tunneling: the ACL must include all the networks you want to join via the VPN:

    tunneling split list of permitted access standard 192.168.101.0 255.255.255.0

    tunneling split list of permitted access standard 192.168.8.0 255.255.255.0

    NAT: Do not use 'everything' in the nat exemption, but specify all the traffic that should not be natted:

    IP 192.168.101.0 allow Access-list extended sheep 255.255.255.0 192.168.201.0 255.255.255.0

    IP 192.168.8.0 allow Access-list extended sheep 255.255.255.0 192.168.201.0 255.255.255.0

    Routing: The 1941 needs a route for the vpn-pool pointing on the SAA (just in case there is no default route to the ASA)

    --
    Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
    http://www.Kiva.org/invitedBy/karsteni

  • Ipad Cisco ipsec VPN connects but not access to the local network

    Hi guys,.

    I am trying to connect our ipads to vpn to access network resources. IPSec cisco ipad connects but not lan access and cannot ping anything not even not the interfaces of the router.

    If I configure the vpn from cisco on a laptop, it works perfectly, I can ping all and can access resources on the local network if my guess is that the traffic is not going in the tunnel vpn between ipad and desktop.

    Cisco 877.

    My config is attached.

    Any ideas?

    Thank you

    Build-in iPad-client is not useful to your configuration.

    You have three options:

    (1) remove the ACL of your vpn group. Without split tunneling client will work.

    2) migrate legacy config crypto-map style. Here, you can use split tunneling

    3) migrate AnyConnect.

    The root of the problem is that the iPad Gets the split tunneling-information. But instead of control with routing traffic should pass through the window / the tunnel and which traffic is allowed without the VPN of the iPad tries to build a set of SAs for each line in your split-tunnel-ACL. But with the model-virtual, SA only is allowed.

  • VPN connected but no visible network

    so I have a windows 7 (VPN server) desktop computer and a windows laptop 7 (VPN client) and I have set up the incoming VPN connection on my desktop and a client VPN connection on my laptop. When I go and establish a VPN connection, it says that I'm connected on my laptop and my desktop but I can't access my network resources. Ive been cracking as a result for a few weeks now and have gotten nowhere with it, any help would be greatly appreciated. Thank you!

    I can't access something like \\ServerName\ShareName I can't do a ping them either. address ranges are not the same on the server or client networks. the funny this is that it says I am connected at both ends, the customer declares that ipv4 has no internet access on the vpn which is fine because all I want is access to the network and it shows that I have an ip address assigned on the vpn map. side server but it is said that ipv4 and ipv6 are not connected, but if I do "ipconfig/all" he shows me his ip address on the vpn.

    client side, I've disabled 'Gateway on remote network use default' so that I can still have access to the internet on the im client that is connected to the vpn. on the side server, I tried selecting "Assign addresses automatically using DHCP" as well as "specify IP addresses (with a beach which is on the client and the server ip address range).» I have also "Allow the calling computer to specify its own IP address" selected on the server.

    When I finally fell a VPN server on a Vista box I got the address assigned to the configuration of clients like that.

    http://theillustratednetwork.MVPs.org/Vista/PPTP/VPNSetup06.jpg

    The address range was the same that the server of the LAN address range, in this case, I used 192.168.10.X on the local network.

    http://theillustratednetwork.MVPs.org/Vista/PPTP/ExampleVistaVPNNetwork.PDF

    Customer recevrait.31 ou.32...

    Of course assumed that the customer was or would not be on a LAN 192.168.10.X to start. If it was so I could have problems connecting to shares on my LAN Server.

    MS - MVP Windows Desktop Experience
    "When all else fails try what the captain suggested before you started...". »

  • L2TP VPN connects but won't see network drives

    Hi all

    I just got a MacBook Pro with El Capitan. I joined it to my area of work and I have implemented SonicWall VPN Client Mobile and I tested it on and it works - only if my network, I am connected to and the VPN will not have the same IP range.

    I would like to use the integrated VPN L2TP client, but I have questions here. I have configurted on my Dell SonicWall and connect this VPN from a remote location, it will connect and show the data transfer (sending / reception are green) but I can not access my network drives.

    Once I have switch back to Mobile Client VPN SonicWall, everything works well.

    Any idea?

    Routing on L2TP or PPTP will probably work or at all, if both ends of the VPN tunnel terminate on the same CIDR network block. Which is why people never give a one VPN server address local 192.168.1.0/24. the network block is much too common. Please use something in 10.x.x.x.

Maybe you are looking for

  • How to download version22

    I accidentally go Mozilla, but a banking program that I use is not compatible with something higher than V22. In the list, I can't understand what file to choose. Please help.

  • I get an error on a connection live in insecurity when Wifi is trying to insert a login Web page.

    Good so I'm at McDonald's. Launch Firefox and type something in the search-home page bar or in the Google search bar at the top. In response, McDonald's presents its usual page 'do you agree our terms?"to connect. However, Firefox displays the "this

  • Newbie: windows form designer generated code

    Hello I am new to MeasStudio and VB.   Currently using MS VB08 with 8.5 MeasStudio of NEITHER.  I am again the example of or 'BasicSignalGeneration '.  Unfortunately, with the User Interface and full hand, I am unable to compile and run the program. 

  • Windows8 xponent compatibility...

    Hi all usually, I use music program m-Audio Torq xponent, but since I'm windows8, I was never able to install it on my pc. Always come an error message, ERROR of EXECUTION, MICROSOFT VISUAL C ++ RUNTIME LIBRARY. Please I'm desperate that can do. Than

  • Big problem with HTML5 for Adform banners

    Had a problem today deliver banners to adform. They claim that the files must be less than 100 KB uncompressed. (I usually delivered less than 100 KB in the format compressed without problem).I check a banner in format 930x600px that it did not conta