VPN: Fulltunnel cannot access on the internet

Similar Questions

• ASA 5505 VPN established, cannot access inside the network

  Hi, I recently got an ASA 5505, and I spent weeks to find a way to set up a VPN on it.

  After a few days, I finally found the solution to connect to my ASA with a VPN client yet and cannot access devices that are connected to the ASA.

  Here is my config:

  ASA Version 8.2 (5)
  !
  hostname asa01
  domain kevinasa01.net
  activate 8Ry2YjIyt7RRXU24 encrypted password
  2KFQnbNIdI.2KYOU encrypted passwd
  names of
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  switchport access vlan 5
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP address dhcp setroute
  !
  interface Vlan5
  No nameif
  security-level 50
  IP 172.16.1.1 255.255.255.0
  !
  passive FTP mode
  DNS server-group DefaultDNS
  domain kevinasa01.net
  permit same-security-traffic intra-interface
  Remote_Kevin_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.254.0 255.255.255.240
  inside_nat0_outbound list of allowed ip extended access all 192.168.254.0 255.255.255.0
  inside_nat0_outbound list of allowed ip extended access entire 192.168.1.0 255.255.255.0
  sheep - in extended Access-list allow IP 192.168.254.0 255.255.255.0 192.168.1.0 255.255.255.0
  access extensive list ip 192.168.254.0 outside_access_in allow 255.255.255.0 any
  access extensive list ip 192.168.254.0 inside_access_in allow 255.255.255.0 any
  pager lines 24
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  pool pool 192.168.254.1 - 192.168.254.10 255.255.255.0 IP mask
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (outside) 1 192.168.254.0 255.255.255.0
  NAT (inside) 0 access-list sheep - in
  NAT (inside) 1 192.168.1.0 255.255.255.0
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Access-group outside_access_in in interface outside
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  management-access inside
  dhcpd outside auto_config
  !
  dhcpd address 192.168.1.5 - 192.168.1.36 inside
  dhcpd allow inside
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  internal Remote_Kevin group strategy
  attributes of Group Policy Remote_Kevin
  value of server DNS 192.168.1.12 192.168.1.13
  VPN - connections 3
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list Remote_Kevin_splitTunnelAcl
  kevinasa01.NET value by default-field
  username kevin mz6JxJib/sQqvsw9 password encrypted privilege 0
  username kevin attributes
  VPN-group-policy Remote_Kevin
  type tunnel-group Remote_Kevin remote access
  attributes global-tunnel-group Remote_Kevin
  address-pool
  Group Policy - by default-Remote_Kevin
  IPSec-attributes tunnel-group Remote_Kevin
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  inspect the icmp error
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:2bb1da52d1993eb9b13c2f6dc97c16cd
  : end

  Thank you

  Hello

  I read your message quickly through my cell phone. I don't know why you have spent your config twice. Maybe a typo issue.

  I see the acl sheep in the wrong way. I mean 192.168.254 are your pool VPN and 192.168.1.0 your local LAN.

  The acl must be:

  sheep - in extended access-list permit ip 192.168.1.0 255.255.255.0 192.168.254.0 255.255.255.0

  For nat (inside), you have 2 lines:

  NAT (inside) 1 192.168.1.0 255.255.255.0 ==> it is redundant as the 1 below does the same thing with more networks if there is inside side. You can delete it.
  NAT (inside) 1 0.0.0.0 0.0.0.0

  Why are you doing this nat (outside)?

  NAT (outside) 1 192.168.254.0 255.255.255.0

  Here are the first questions that I have seen by reading through my mobile. Let's change this and let me know. I'll take a look later with a computer (tonight or tomorrow)

  Thank you.

  PS: Please do not forget to rate and score as good response if this solves your problem.

• VPN clients cannot access to the vlan

  Hello

  I just changed my flat lan to a virtual LAN environment multi, but now I need help to get to my VPN back working again as the VPN user can access servers that are not on the vlan 'door '.  I've read enough to know that it is probably associated with NAT, but I'm not sure where to put this information.

  Does go in the NAT, associated with the E0 interface (outgoing internet gateway), to the vlan10 (vlan router is actually on) or can I create a new one and apply it to the crypto ipsec and isakmp side of things that use VPN users?

  My network is configured as such...

  VPN client - Router1811 - split trunk - C3550 - 12G - shared - resources multiple C3550s - servers/Wstns

  The router subnet 192.168.10.0 as all switches, VLAN is set up through the 12 G and all other switches as vtp "vtp clients", including the router.  The user can get to the 10 subnet and any server on it, but not to the"farm" on the subnet 192.168.11.0.

  I noticed Federico has been working on something very similar to this... but any help would be appreciated.

  Thank you, Don

  Hi Don,

  Please mark this discussion as resolved if there is no other problem with this VPN.

  See you soon,.

  Nash.

• VPN ssl cannot access the internet

  Hello guys!

  I need help to allow access to the internet for my vpn users. I can connect with Anyconnect but do not have access to the internet. Subnet for VPN is 192.168.100.0. I welcomed this subnet on my cisco router.

  ISP-> router-> 192.168.0.0-> ASA-> 192.168.1.0 (887VA)

  Here is my config:

  ASA Version 9.1 (3)

  mask of local pool AnyConnect 192.168.100.1 - 192.168.100.254 IP 255.255.255.0

  network of the NETWORK_OBJ_192.168.100.0_24 object

  255.255.255.0 subnet 192.168.100.0

  NAT (inside, outside) static source any any static destination NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search to itinerary

  Trust SSL VPN outside

  Trust SSL VPN inside

  WebVPN

  allow inside

  allow outside

  AnyConnect image disk0:/anyconnect-win-3.1.04072-k9.pkg 1

  AnyConnect enable

  tunnel-group-list activate

  attributes of Group Policy DfltGrpPolicy

  L2TP ipsec ikev2 VPN-tunnel-Protocol

  internal GroupPolicy_VPN group strategy

  attributes of Group Policy GroupPolicy_VPN

  WINS server no

  client ssl-VPN-tunnel-Protocol

  Split-tunnel-policy tunnelall

  username alex Awards

  VPN-group-policy GroupPolicy_VPN

  VPN Tunnel-group type remote access

  General-attributes of VPN Tunnel-group

  address pool AnyConnect

  Group Policy - by default-GroupPolicy_VPN

  VPN Tunnel-group webvpn-attributes

  enable VPN group-alias

  Thank you very much!

  Hello

  Make sure you have this configuration

  permit same-security-traffic intra-interface

  You can check with

  See the race same-security-traffic

  If you don't have it then add it and test again.

  If this does not work after this then check if your router is to see all this traffic. For example you see any translation NAT on the router to your VPN users?

  What NAT configuration did you use for testing? I suggest 2 options above.

  First of all, one was to change the current VPN Client NAT0 configuration and dynamic addition PAT for VPN users to the Internet.

  Second, it was just to change the configuration of NAT0

  -Jouni

• The VPN Clients cannot access any internal address

  Without a doubt need help from an expert on this one...

  Attempting to define a client access on an ASA 5520 VPN that was used only as a

  Firewall so far. The ASA has been recently updated to Version 7.2 (4).

  Problem: Once connected, VPN client cannot access anything whatsoever. Client VPN cannot

  ping any address on internal networks, or even the inside interface of the ASA.

  (I hope) Relevant details:

  (1) the tunnel seems to be upward. Customers are the authenticated by the SAA and

  are able to connect.

  (2) by many other related posts, I ran a ' sh crypto ipsec her "to see the output: it

  appears that the packets are décapsulés and decrypted, but NOT encapsulated or

  encrypted (see the output of "sh crypto ipsec his ' home).

  (3) by the other related posts, we've added commands associated with inversion of NAT (crypto

  ISAKMP nat-traversal 20

  crypto ISAKMP ipsec-over-port tcp 10000). These were in fact absent from our

  Configuration.

  (4) we tried encapsulation TCP and UDP encapsulation with experimental client

  profiles: same result in both cases.

  (5) if I (attempt) ping to an internal IP address of the connected customer, the

  real-time log entries ASA show the installation and dismantling of the ICMP requests to the

  the inner target customer.

  (6) the capture of packets to the internal address (one that we try to do a ping of the)

  VPN client) shows that the ICMP request has been received and answered. (See attachment

  shooting).

  (7) our goal is to create about 10 VPN client of different profiles, each with

  different combinations of access to the internal VLAN or DMZ VLAN. We do not have

  preferences for the type of encryption or method, as long as it is safe and it works: that

  said, do not hesitate to recommend a different approach altogether.

  We have tried everything we can think of, so any help or advice would be greatly

  Sanitized the ASA configuration is also attached.

  appreciated!

  Thank you!

  It should be the last step :)

  on 6509

  IP route 172.16.100.0 255.255.255.0 172.16.20.2

  and ASA

  no road inside 172.16.40.0 255.255.255.0 172.16.20.2

• Windows 8.1 and cannot connect to the internet even though I have full WiFi access.

  Original title: Windows 8.1 and cannot connect to internet even though I have full WiFi access-problem occurred just after working fine for over a year

  Uses Windows 8.1 for over a year with no access to the internet.  Today, I can access is no longer the internet using Explorer, Mozilla Fire Fox or store apps.  (Tried to install a game just to test the internet connection-no luck).  When I try to connect the computer just sits there with the indicator connection just spin but never passes through.  I have good indicated WiFi (Internet) access.  While they inspected the updates, the only thing that appears on the current date is some Microsoft Silverlight is.  Could that that may cause my problem?  I didn't do any changes and have no problem until today.  I'm not always well informed in this area and I am at a total loss as to how to proceed, what to check... hope someone can advise me.   Thank you, DebbieG211

  Hi Debbie,.

  You might face this problem because of wrong settings in Internet Explorer. You mentioned that you get the update of windows Microsoft Silverlight, so we can deduce that there is a problem with the Internet browser. Please write us with the following details.

  (1) do you get error messages when all websites fail to load?

  (2) what is the brand and model of your computer?

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows/cant-connect-Internet#1TC=Windows-8

  You can also follow the steps in the link below for further troubleshooting. It is a tutorial to solve the problem of wireless and wired connections.

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-81&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Let us know the details asked and the status of the issue.

• Cannot use applications that need access to the internet

  I have problems with a number of applications on my Vista system.  All worked well until a few days ago (I ran the Symantec Conficker and Msft Malware tools so am sure it isn't the Conficker virus).  I am connected to the internet and can go to websites via IE.  However, applications that require access to the Internet are faulty.  It started with Windows Live Messenger, which would not start (error message has been that there was a problem).  After much effort I uninstalled but impossible to reinstall as the installer does not due to "not connected to the internet.  Another application shows an error 80072efd - lack of connection.  I can't configure Norton due to the lack of ability to connect to services.  Any ideas?  Thanks in advance...

  Hi DebAlex,

  Is the name of the application Python ring a Bell to you? It is a programming language and PyWin32 is an extension for it.  Please do a search on your computer (include files and hidden folders) for the file name pythonw.exe and pywin32.
   
  Depend on whether you use on your computer or not Python, you might want to try find it in Control Panel--> programs and features and remove it from the list if you use the program.

  If you do not use the program, rename the folder these files are locate in (if you can find using the search).  Other people with the same error were able to fix this way.

  Let us know if this helps, Kevin
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Cannot open email in Hotmail via Firefox. I have Vista installed on the pc and Windows 7 on the laptop, but cannot access all the features of Hotmail.

  Cannot open email in Hotmail via Firefox. I have Vista installed on the pc and Windows 7 on the laptop, but cannot access all the features of Hotmail. I tried to clear the cache and restart Firefox, but I still cannot use Hotmail.

  Not this problem when I go to Internet Explorer.

  Hello, it was noted that the foxit pdf plugin is causing this issue. You can disable this plugin in firefox > addons > plugin until what foxit offers a patch/update for the plugin.

• Access to the Internet and get a "atl100.dll" error when you try to use Firefox

  I just reinstalled Vista Home Premium and everything was going well for two days, but I can not access the internet regardless of the browser that I use and when I open Firefox, I got an error of "atl100.dll", I am afraid that my files cd, especially the .dll files can be altered, where can I find a good (and costs nothing) copy of the file atl100.dll? Please help as soon as possible. Thank you!!

  Original title: Re-installed Vista Home Premium and cannot access the internet & get a "atl100.dll" error when trying to use Firefox and IE just is not access to the internet either

  Hello

  1 did you changes to the computer before the show?

  2. What is the full error message?

  3. who is the antivirus installed on the computer program?

  4 are you using wired or Wi - Fi to access the Internet?

  5. What is the version of Internet Explorer installed on the computer?

  The possible causes:

  • ATL100.dll file is missing, as it was accidentally deleted from your computer
  • ATL100.dll file is damaged by viruses and your computer cannot access the file.
  • ATL100.dll associated with registry files is corrupt and obsolete.

  Perform the steps:

  Method 1: Perform a SFC scan on your computer to fix the corrupt dll files.

  Reference:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Method 2: Run a scan antivirus on your computer.

  www.Microsoft.com/Security/Scanner

  Note: If infections are detected during the scan, there is a risk of data loss because infected files will be deleted.

  Method 2: Reset of internet explore and check. (If you use Internet Explorer)

  How to reset Internet Explorer settings

  http://support.Microsoft.com/kb/923737

  Warning: Reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings.

  For more information, see the links:

  The problems of Internet connection

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  I hope this helps.

• WAG-120N and static ip - wireless and wired clients cannot connect to the internet

  Greetings,

  I use the N WAG-120 AP and switch for 3 computers laptops and 2 Office. Our Department is assigned only a what IP static of our server, as well as a pc can connect to the server and the internet. I use the first lan port of the 120N Wag as a WAN port and I attribute the static IP address, and the subnet, default gateway, and DNS addresses. Connected clients receive an ip address from the DHCP (192.168.1.10x) router, but cannot connect to the internet. How can I configure my router to allow clients to connect?

  Thank you in advance!

  The default LAN IP of the WAG subnet is 192.168.1.0/255.255.255.0 belongs to 192.168.0.0/255.255.0.0. This means that 192.168.1.0 IP addresses exist side WAN and LAN of the WAG. What makes this configuration completely cannot be routed.

  Change the address LAN IP of the WAG to an IP outside the corporate network, for example using IP addresses private 172.16/12, for example to set the address LAN IP 172.16.1.1 with 255.255.255.0 subnet mask.

  The alternative would be to use the WAG as a point of easy access only, and not as a router. However, due to the 255.255.0.0 subnet in your network company you will not be able to access the web interface except from an IP address corresponding to the LAN IP address subnet of the WAG. Of course, this does not affect the wireless or wireline customers connected to the WAG...

• Windows Update does not, Media Player cannot access track info, internet Explorer does not

  As the title. Firefox works well, all Web sites work well, but nothing to do with windows cannot connect to the internet.
  This has happened for a long time, using more than one modem and the router. Only windows firewall is activated, also tried to turn it off.
   
  I lost something important somewhere, or changed a setting accidentally?
  Updated to explore 9, still no luck.

  Hello DavebTD,

  Thanks for your post.  Remember that Windows Update requires the use of Internet Explorer.  You try to access the Windows Update with Firefox page?  We can't wait to hear back on your part.

  See you soon

• The VPN Clients need access to the subnet on another router

  Hello

  We have a pix 515e PIX Version 8.0 (2)

  We have two subnet 10.1.x.x/16 and 10.2.x.x/16

  The firewall is on 10.1.x.x and vpn clients can access this subnet.

  The firewall can ping 10.2.x.y where x is a server in the other subnet.

  On the 10.2.x.x customers out the firewall.

  The problem is that vpn clients cannot access the server of 10.2.x.y even if the pix can ping 10.2.x.y and the road for him.

  What I need to check that the vpn rules are correct in the pix 515e?

  I think it is a rule of exemption nat or something like that not exactly sure.

  Everything would be a great help.

  Thank you

  Hello

  For clients VPN access to these subnets, check the following:

  1 NAT exemption include these subnets (if not using NAT)... it's the NAT0 ACL command

  2. these subnets is included in the split tunneling

  3. these subnets have a route to the PIX to send traffic to the VPN client pool.

  4. There are no ACLs not applied to the inside interface of the PIX deny this communication.

  Federico.

• My laptop cannot connect to the internet with the error (code 31) Qualcomm Atheros AR9485WB-EG Wireless Network Adapter

  Hi, my laptop have this problem cannot connect to the internet, but the bar shows that I am connected to the network, but without access to the internet.

  I tried someone's guide to uninstall the network adapter in Device Manager and then reinstall it again, but now I'm stuck with the laptop cannot even detect the wireless network and the "Qualcomm Atheros AR9485WB-EG Wireless Network Adapter ' on Device Manager displays this message"the device is not working properly because Windows cannot load the drivers required for this device. (Code 31)"

  I forgot since when this problem persists.

  Please help me with this problem of internet connection,

  List of maybe / don't may not be the problem:

  1. I had mcafee antivirus 3 weeks around which has already expired for about 50 days and I uninstalled to turn into kaspersky anti-virus

  2. my windows is still 8.0

  3 ASUS N56V

  4. browser chrome incognito window

  Thank you Mr President, I found a solution for this problem

  I just turn on the download via connections counters my PC-> devices config->download via connections counters

  and then I tried to enter the following command at the command prompt run as administrator

  netsh int ip reset c:\resetlog.txt

  I hope this helps anyone else having the same problem as mine

  Thank you again Sir

• Satellite L550-13u has no access to the internet

  Hello

  I have my laptop for a year and last week I had a problem, the laptop had no access to the internet but my other laptop (acer) had internet access.
  My brother has solved the problem. And it's happening again now, and it isn't here...
  This is why I post here. So I think it's a problem of the realtek software, or could you give your ideas and solutions if you had the same problem please.
  (I am a student and I need connection because I was about to download ubuntu packages to learn to use developers files).

  Note: My laptop has been 32-bit of windows 7 and Ubuntu 10.10 Maverick 32-bit; just to give you the info on the laptop.

  You use the local network Ethernet or wireless?

  You have disabled your firewall?

  Have you tried another browser like Firefox?

  The Internet don't miss to connect both on Windows and Linux?

  You have the latest version of the BIOS installed and configured the default settings?

• Restrited access and without access to the internet

  When I connect my new computer home, he sees all the wifi nearby, and I can connect with my wifi. When I get to the Office I opened the computer, he sees our netgear wifi and wifi. That I connect to our wifi, after a time, she becomes limited or restrited and then I have more access to the internet. What are the causes that she. After that, I do not see any other wifi nearby either.

  I've updated the LAN driver and it solved the problem as you have suggested.

  Tthank you