VPN - SRP527W <>Cisco 857 established but no tx fraffic side SRP
I have now established between SRP527w and cisco 857 ACE, but if I ping from a multitude of Cisco to a host on the side of the PRS I get only rx traffic in the tunnel, the stats keep tx 0 and ping is not answered.
My tunnel is to send a voice call in IPSEC tunnel keeping DSCP bits, it communicates vlan voice SRP with Cisco lan.
I have the SRP 2 VLAN:
1 vlan for data on ports 1, 2, and 4
1 voice vlan ports 1,2,3,4.
I connect a netbook to port 3 and I can connect to the internet, but I can't reach by ping across the tunnel
Perhaps the traffic of the vlan is voice natted with the ip address of data vlan?
I need all traffic must go through the tunnel without being natted on the cisco side I have a policy to avoid the nat but don't know if SRP have no problem about it too.
All gateways are ok
Any idea greatly appreciated, thank you very much
Hi, manual,.
The RPS not NAT via the tunnel, which shouldn't be a problem.
You try to ping a client in the remote subnet, or IP address to the VLAN RPS at the other end of the tunnel? (Could you try both please?)
See you soon
Andy
Tags: Cisco Support
Similar Questions
-
Hello
I would like to know if CISCO 857 allows customers of Cisco VPN remote apart from site to site VPN software. I have heard that all cable cisco VPN devices allow connections to cisco VPN client software, is it true?
Thanks a lot for your help
Juan Manuel
Juan,
Let me explain a little further in order to clarify some of the terminology used, which could lead to confusion.
Router Cisco VPN may terminate the following types of tunnels.
Lan to Lan tunnels has.
b. dynamic tunnels of Lan to Lan
c. connections from VPN clients
d. ends for easy VPN clients
a & b are very similar
c & d are very similar
except - option c uses VPN (software) clients installed on the PC or MAC systems
Option d, material uses to connect to the IOS routers. You can use a router or a PIX firewall or a 3002 or ASA to connect to the Cisco router that would act as an IOS Easy VPN server. But the device to connect to the easy VPN server is called an easy VPN client.
Hope that explains the terminology a little more in detail.
To answer your question, safety feature Easy VPN client and server support.
And what you're trying to accomplish is option c. Thus, security feature option should work well for you.
Hope that explains your queries.
The rate of this post, if that helps!
Thank you
Gilbert
-
Pass through IPSEC on Cisco 857
Hello people!
I have gained reciently a Cisco 857 router. I want to do a site-to-site VPN.
I set up the ATM0.1 with "ip unnumbered" VLAN 1 interface. I have not configured the router to enable NAT or PAT. VLAN 1 is configured with a public Ip of my ISP address. Behind the cisco router, I have a Zywall 5, this device is my VPN gateway. Initially, it works very well with the other soho router but it blocks often, for this reason, I decided to change it for a cisco router.
My problem now is that the cisco router does not allow the implementation of VPN.
Need to activate the IPSEC pass-through?, how can I do this?
Thanks in advance!
If you connect through the console:
recording console 7
If you connect via telnet:
farm forestry monitor 7
monitor terminal
Concerning
Farrukh
-
URGENT! RDP with Cisco 857
Hi experts,
I configured a Cisco 857 - k9 for the remote vpn clients. everything works very well. but I have a question, is it possible on this 857 router to allow remote clients to start an RDP session with a server?
Thank you & best regards
See that there is no real answer to that. Depends on your network 'special '. If the VPN client can reach the host RDP with just the name of the server (Via the DNS configured on its virtual adapter), then this is all you need. If there is no assigned DNS server (you hosts files bits). If the DNS server will not resolve the host without the FULL domain name, you must the field to map VPN. Just do what works for you :)
Concerning
Farrukh
-
Hi all
I am trying to create a VPN between a PIX and a Cisco 877W tunnel but can't seem to get the tunnel. When I do a 'sho crypto session"on the Cisco 877, I get, he said session state is declining, then changed to NEGOTIATE DOWN, but it is now down again... Please find attached the configs for both ends... Are there commands to confirm that the tunnel is up other than to try to ping the remote end? I would greatly appreciate any help lift this tunnel.
Kind regards
REDA
Hello
Based on the configurations of joined, to do some changes. For example:
1. the isakmp policies do not match on the router and the pix. Make sure the hash group Diffie-Hellman and life correspond on the 877 and pix.
2. the access list for the ipsec traffic must be images of mirror of the other.
3. make sure life of ipsec on the two peers.
I hope it helps.
Kind regards
Arul
Rate if this can help.
-
Client access VPN from Cisco 876 does not work
Hello
I have the router Cisco 876 (with 12.4 (4) T2 IOS) and Cisco VPN client worm. 4.6.02).
I am trying to configure my router as a VPN concentrator for 2 groups, but the implementation of tunnel fails already with the negotiation of parameters. Please find attached config and the «debug crypto isakmp» output Ethereal trace is also included (the customer has to IP: 172.24.4.61, interface of routers is 172.24.34.67).
I tried to downgrade to IOS and changed the platform at 2821, but with the same result.
Let me know if you can see the problem.
Thank you!
Lubomir
C876 config:
votre_nom #sh run
Building configuration...
Current configuration: 2457 bytes
!
version 12.4
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
hostname yourname
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
!
AAA new-model
!
!
Konzola AAA authentication login no
local VPN_access AAA authentication login
local VPN_access AAA authorization network
!
AAA - the id of the joint session
!
resources policy
!
IP subnet zero
IP cef
!
!
!
!
no ip domain search
!
!
!
username privilege 15 secret xxxx cisco
!
!
!
crypto ISAKMP client configuration USERS group
two key
pool USERS_pool
!
Configuration group customer crypto isakmp ADMIN
a key
pool ADMIN_pool
Crypto isakmp USERS_Profile profile
Group USERS of identity match
list of authentication of client VPN_access
VPN_access of ISAKMP authorization list.
initiate client configuration address
client configuration address respond
Crypto isakmp ADMIN_Profile profile
Group of ADMIN identity match
list of authentication of client VPN_access
VPN_access of ISAKMP authorization list.
initiate client configuration address
client configuration address respond
!
!
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
!
crypto dynamic-map ADMIN 1
game of transformation-ESP-3DES-MD5
ADMIN_Profile Set isakmp-profile
market arriere-route
!
crypto dynamic-map USERS 1
game of transformation-ESP-3DES-MD5
USERS_Profile Set isakmp-profile
market arriere-route
!
!
map VPN_Pristup 1-isakmp dynamic ipsec ADMIN crypto
card crypto VPN_Pristup 2-isakmp dynamic ipsec USERS
!
!
!
!
interface BRI0
no ip address
encapsulation hdlc
Shutdown
!
ATM0 interface
no ip address
Shutdown
No atm ilmi-keepalive
DSL-automatic operation mode
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Vlan1
IP 172.24.34.67 255.255.255.0
IP tcp adjust-mss 1452
card crypto VPN_Pristup
!
IP pool local USERS_pool 10.1.1.10 10.1.1.20 USERS group
IP pool local ADMIN_pool 10.2.1.10 10.2.1.20 group ADMIN
IP classless
IP route 0.0.0.0 0.0.0.0 172.24.34.1
!
!
IP http server
local IP http authentication
IP http secure server
IP http timeout policy slowed 5 life 86400 request 10000
!
not run cdp
!
!
control plan
!
!
Line con 0
authentication of the connection Konzola
no activation of the modem
line to 0
line vty 0 4
privilege level 15
transport input telnet ssh
line vty 5 15
privilege level 15
transport input telnet ssh
!
max-task-time 5000 Planner
end
votre_nom #.
votre_nom #.
Hello
where is isakmp policy commands crypto. In short, you have not configured the phase 1...
* 06:07:20.347 Mar 1: ISAKMP: (0): atts are not acceptable. Next payload is 0
* 06:07:20.351 Mar 1: ISAKMP: (0): no offer is accepted!
* 1 Mar 06:07:20.351: ISAKMP: (0): phase 1 SA policy is not acceptable! (local 172.24.34.67 remote 172.24.4.61)
Vikas
-
I'm losing configuration when I turned off my Cisco 857 router
I bought the new router Cisco 857 of the shop. Router must have been used before as I couln can't go inside with name of user and password default cisco/cisco.
Well I followed digital and reset the password for the user name and password. Now I have finally connected to Cisco CP express on my IE browser.
I discovered that someone was using a router in the shop that's why I countries: ' t log in to him in the first place. In any case the problem is that when I changed my configuration and applies the settings he remembers until I turned off. When I turn on again he remembers all the parameters of this shop.
He returned everything back: IP address, former account to level 15 and password - just like after the password reset.
I tried again and he again lost the settings. So I found instructions:
http://www.Cisco.com/en/us/products/HW/routers/ps233/products_tech_note09186a00800a65a5.shtml
I followed it and changed once again all the settings of the router. My settings are still lost after the power on/off. I noticed that when I do everything first bit it shows
0x2102 not 0x2142 like they think that is password reset mode.
Here is my output from Hyper Terminal:
=============================
Cisco#enable
Cisco#show start
Using 3359 out of 131072 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Cisco
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
enable secret 5 $1$hpKF$Rc1tl6r45J8iHG7EN5jSk.
!
no aaa new-model
!
crypto pki trustpoint TP-self-signed-3185909327
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3185909327
revocation-check none
rsakeypair TP-self-signed-3185909327
!
!
crypto pki certificate chain TP-self-signed-3185909327
certificate self-signed 01 nvram:IOS-Self-Sig#5.cer
dot11 syslog
no ip dhcp use vrf connected
ip dhcp excluded-address 10.10.10.1
!
ip dhcp pool ccp-pool
import all
network 10.10.10.0 255.255.255.248
default-router 10.10.10.1
lease 0 2
!
!
ip cef
no ip domain lookup
ip domain name molinary.com
!
!
!
username admin privilege 15 secret 5 $1$jD3j$r6ROikgGsIlcMTGjkxFQ6.
username username privilege 15 password 0 password
!
!
archive
log config
hidekeys
!
!
!
!
!
interface ATM0
no ip address
shutdown
no atm ilmi-keepalive
dsl operating-mode auto
!
interface ATM0.1 point-to-point
description $ES_WAN$
ip nat outside
ip virtual-reassembly
pvc 0/38
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$
ip address 10.10.10.1 255.255.255.248
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1452
!
interface Dialer0
ip address dhcp
encapsulation ppp
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication chap pap callin
ppp chap hostname [email protected]/* */
ppp chap password 0 netgear01
ppp pap sent-username [email protected]/* */ password 0 netgear01
!
ip forward-protocol nd
!
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 1 interface ATM0.1 overload
!
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 10.10.10.0 0.0.0.7
dialer-list 1 protocol ip permit
no cdp run
!
control-plane
!
banner exec ^C
% Password expiration warning.
-----------------------------------------------------------------------
Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username
privilege 15 secret 0 Replace
and with the username and password you want to use.
-----------------------------------------------------------------------
^C
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
!
line con 0
login local
no modem enable
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet ssh
!
scheduler max-task-time 5000
end
Cisco#
Cisco#
Cisco#
Cisco#
Cisco#
Cisco#
Cisco#
Cisco#
Cisco#show version
Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, R
ELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Fri 22-Jan-10 14:46 by prod_rel_team
ROM: System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARE
Cisco uptime is 20 minutes
System returned to ROM by power-on
System image file is "flash:c850-advsecurityk9-mz.124-15.T12.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
Cisco 857 (MPC8272) processor (revision 0x400) with 59392K/6144K bytes of memory
.
Processor board ID FCZ140792J5
MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10
4 FastEthernet interfaces
1 ATM interface
128K bytes of non-volatile configuration memory.
20480K bytes of processor board System flash (Intel Strataflash)
Configuration register is 0x2102
Cisco#
Cisco#
Cisco#
Cisco#end
Translating "end"
% Unknown command or computer name, or unable to find computer address
Cisco#reload
Proceed with reload? [confirm]
*Mar 1 01:19:27.786: %SYS-5-RELOAD: Reload requested by username on console. R
eload Reason: Reload Command.
System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARE
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2006 by cisco Systems, Inc.
C850 series (Board ID: 2-149) platform with 65536 Kbytes of main memory
Booting flash:/c850-advsecurityk9-mz.124-15.T12.bin
Self decompressing the image : ############################################## [O
K]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, R
ELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Fri 22-Jan-10 14:46 by prod_rel_team
Image text-base: 0x8002007C, data-base: 0x814E7240
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
Cisco 857 (MPC8272) processor (revision 0x400) with 59392K/6144K bytes of memory
.
Processor board ID FCZ140792J5
MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10
4 FastEthernet interfaces
1 ATM interface
128K bytes of non-volatile configuration memory.
20480K bytes of processor board System flash (Intel Strataflash)
no ip dhcp use vrf connected
^
% Invalid input detected at '^' marker.
SETUP: new interface NVI0 placed in "shutdown" state
Press RETURN to get started!
*Mar 1 00:00:03.952: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State change
d to: Initialized
*Mar 1 00:00:03.960: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State change
d to: Enabled
*Mar 1 00:00:07.244: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to
up
*Mar 1 00:00:08.413: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et0, changed state to up
*Mar 1 00:00:08.821: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 01:19:27.072: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state t
o up
*Mar 1 01:19:27.352: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, R
ELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Fri 22-Jan-10 14:46 by prod_rel_team
*Mar 1 01:19:27.352: %SNMP-5-COLDSTART: SNMP agent on host Cisco is undergoing
a cold start
*Mar 1 01:19:27.436: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Mar 1 01:19:27.436: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Mar 1 01:19:27.540: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, chan
ged state to down
*Mar 1 01:19:28.072: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Ac
cess1, changed state to up
*Mar 1 01:19:28.484: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, cha
nged state to up
*Mar 1 01:19:28.484: %LINK-5-CHANGED: Interface ATM0, changed state to administ
ratively down
*Mar 1 01:19:28.848: %LINK-5-CHANGED: Interface NVI0, changed state to administ
ratively down
*Mar 1 01:19:28.932: %LINK-3-UPDOWN: Interface FastEthernet3, changed state to
up
*Mar 1 01:19:28.936: %LINK-3-UPDOWN: Interface FastEthernet2, changed state to
up
*Mar 1 01:19:28.940: %LINK-3-UPDOWN: Interface FastEthernet1, changed state to
up
*Mar 1 01:19:29.484: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, chan
ged state to down
*Mar 1 01:19:29.932: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et3, changed state to down
*Mar 1 01:19:29.936: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et2, changed state to down
*Mar 1 01:19:29.940: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et1, changed state to down
*Mar 1 01:19:29.948: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et0, changed state to upAuthorized access only!
===========================================
Please help me as I am stuck and can't go any further....
Hi Dragan,
After you run the wizard Cisco CP Express, it should save the configuration set to update the flash on the router. However, in your case, it seems this is not the case. Therefore:
- Configure the device via Cisco CP Express--> do NOT turn off after that
- Connect to the router with Hyperterminal. Enter the configuration mode by typing:
Enable
When you are prompted for a password to put in. The line should now be router #.now type:
write memoryYou see errors? Otherwise, type:
See the startup-configCheck the output matches the configuration you've tried. If Yes, then you are good to go. If this is not the case, let us know all the errors you received.
-
I have created a VPN connection and it worked but you can't see how to remove Windows 7.
Delete the VPN connection
I have created a VPN connection and it worked but you can't see how to remove Windows 7. I tried rt-click but no delete option.Open network and sharing Center. On the left side, click on change adapter settings. You will get all VPN connections that have been created and you can delete what you don't need.
-
What VPN work as a PPTP vpn firewall CISCO-ASA-5520.
Hi all
Can you please tell me which replace the VPN I can configure PPTP on ASA 5520 firewall. What VPN work as a PPTP vpn firewall CISCO-ASA-5520.
You can use the wizard VPN of RA with ASDM and confiugre L2TP IPSEC VPN that does not need a VPN Client must be installed.
Michael
Please note all useful posts
-
VPN connection is established but cannot ping subnet
Hello, I have a 851 router that I'm trying to learn with, I have a config of work that makes me online and has a basic firewall and dhcp for clients. Then, I wanted to add a VPN using the 851 and the Cisco VPN client.
Using this tutorial "http://www.cisco.com/en/US/customer/products/sw/secursw/ps5318/products_configuration_example09186a00806ad10e.shtml."
I was able to get partially to my goal as I can establish a vpn and it shows me 192.168.1.0 as the route secure, but I don't ping or communicate with anything with in the 192.168.1.1 network.
Try this one too.
Instead of using access-list in declaration of NAT, use the route map and see if it solves the problem.
1 deny traffic Ipsec in NAT access list.
access-list 120 refuse 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255
access-list 120 allow 192.168.1.0 0.0.0 all
2. create a roadmap
sheep allowed 10 route map
corresponds to the IP 120
3. no nat ip within the source list 1 interface FastEthernet4 overload
4 ip nat inside source map route sheep interface FastEthernet4 overload
5 disable the ip nat translation *.
Then check.
HTH
Sangaré
-
Client VPN und Cisco asa 5505 tunnel work but no traffic
Hi all
I am new to this forum and Don t have a lot of experience with Cisco, so I hope I can get help from specialists.
I have the following problem:
I installed und konfigured ASA 5505 for use with vpn client. I would like to access the local network from outside through vpn.
To test, I installed ASA 5505 with ADSL (pppoe) and tried to give access to the internal network.
Of course whenever I have recive the supplier's different IP address, but it didn't is not a problem reconfigure in the vpn client.
After the connection is established (vpn tunnel work) I can see my external network packets. But I Don t have any connection to the internal network.
I erased my setup yesterday and tried to reconfigure ASA again. I didn t tested yesterday, because it was too late. And I know that I Don t have the authorization rule at present by the ACL. But I think I'm having the same problem again. (tunnel but no traffic).
What I did wrong. Could someone let me know what I have to do today.
With hope for your help Dimitri.
ASA configuration after reset and basic configuration: works to the Internet from within the course.
: Saved
: Written by enable_15 to the CEDT 20:29:18.909 Sunday, August 29, 2010
!
ASA Version 8.2 (2)
!
ciscoasa hostname
activate 2KFQnbNIdI.2KYOU encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
PPPoE client vpdn group home
IP address pppoe setroute
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
boot system Disk0: / asa822 - k8.bin
passive FTP mode
clock timezone THATS 1
clock to summer time CEDT recurring last Sun Mar 02:00 last Sun Oct 03:00
DNS domain-lookup outside
DNS server-group DefaultDNS
Server name 194.25.0.60
Server name 194.25.0.68
DM_INLINE_TCP_1 tcp service object-group
port-object eq www
EQ object of the https port
inside_access_in list extended access permitted udp 192.168.1.0 255.255.255.0 no matter what eq field open a debug session
inside_access_in list extended access permitted tcp 192.168.1.0 255.255.255.0 any object-group DM_INLINE_TCP_1 open a debug session
inside_access_in list extended access deny ip any any debug log
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.0.0 255.255.0.0
permit inside_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 192.168.10.0 255.255.255.128
homegroup_splitTunnelAcl list standard access allowed 192.168.10.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
IP local pool homepool 192.168.10.1 - 192.168.10.100 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm-625 - 53.bin
ASDM location 192.168.0.0 255.255.0.0 inside
ASDM location 192.168.10.0 255.255.255.0 inside
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
inside_access_in access to the interface inside group
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
VPDN group home request dialout pppoe
VPDN group House localname 04152886790
VPDN group House ppp authentication PAP
VPDN username 04152886790 password 1
dhcpd outside auto_config
!
dhcpd address 192.168.1.5 - 192.168.1.36 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
TFTP server 192.168.1.5 inside c:/tftp-root
WebVPN
Group Policy inner residential group
attributes of the strategy of group home group
value of 192.168.1.1 DNS server
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list homegroup_splitTunnelAcl
username user01 encrypted password privilege 0 v5P40l1UGvtJa7Nn
user01 username attributes
VPN-strategy group home group
tunnel-group home group type remote access
attributes global-tunnel-group home group
address homepool pool
Group Policy - by default-homegroup
tunnel-group group residential ipsec-attributes
pre-shared-key ciscotest
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:930e6cddf25838e47ef9633dc2f07acb
: end
Hello
Normally, you want a static public IP address on the ASA to allow it to receive connections from VPN clients (avoid to change the IP address all the time).
If you connect via VPN, check the following:
1. the tunnel is established:
HS cry isa his
Must say QM_IDLE or MM_ACTIVE
2 traffic is flowing (encrypted/decrypted):
HS cry ips its
3. Enter the command:
management-access inside
And check if you can PING the inside ASA VPN client IP.
4. check that the default gateway for the LAN internal ASA within intellectual property (or there is a road to the ASA to send traffic to the VPN clients).
Federico.
-
VPN Tunnel established but no LAN access
I have an embarrassing problem where more remote site PCs are accessing resources HQ LAN very well using the VPN Client (v4.6) connecting to a Cisco PIX 515E. Any PC running Windows XP SP2 with the firewall off o/s. A PC site however establishes the IPSEC tunnel, but cannot communicate with network resources (Intranet, Email, etc) and it also times out ping machines which must meet. I noticed when running VPN stats on the client, even if the packages are be encrypted, they may not be decrypted and there are many packets discarded. I'm quite a beginner when it comes to Cisco VPN if someone at - it clues as to why a machine will not work when it is exactly the same configuration as the others what to do.
No problem
If possible mark this issue as resolved on this forum - its useful when you search for old messages
M.
-
Tunnel established but no traffic passing on the Site 2 Site VPN
I have a cisco 2900 series construction of a site-2-site of the ASA 5510 vpn tunnel. The tunnel works out very well, but I can't get the traffic through the tunnel. I have read several other posts and tried a lot of suggestion (probably to break things in the process). I don't know if I'm not nat all messed up or if my access lists on the router are goofy. Any help is greatly appreciated.
THE ASA CONFIG:
ASA 4,0000 Version 1
!
hostname test-fw
domain ficticious.localnames of
!
interface Ethernet0/0
nameif outside
security-level 0
IP address *. *. * 255.255.255. *.
!
interface Ethernet0/1
nameif inside
security-level 100
IP 192.168.3.2 255.255.255.0
!
interface Ethernet0/2
nameif DMZ - TNS
security-level 10
IP 192.168.31.1 255.255.255.0
interface Ethernet0/3
nameif DMZ-SMTP
security-level 9
192.168.32.1 IP address 255.255.255.0
!
interface Management0/0
nameif cradelpoint
security-level 1
192.168.254.1 IP address 255.255.255.0
!
boot system Disk0: / asa844-1 - k8.bin
passive FTP mode
clock timezone IS - 5
clock to summer time EDT recurring
DNS server-group DefaultDNS
domain ficticious.local
network object obj - 172.16.3.2
host 172.16.3.2
network object obj - 172.16.7.2
Home 172.16.7.2
network object obj - 172.16.10.2
Home 172.16.10.2
network object obj - 172.16.13.2
Home 172.16.13.2
network object obj - 192.168.3.0
subnet 192.168.3.0 255.255.255.0
network object obj - 192.168.4.0
subnet 192.168.4.0 255.255.255.0
network object obj - 192.168.5.0
192.168.5.0 subnet 255.255.255.0
network object obj - 192.168.6.0
192.168.6.0 subnet 255.255.255.0
network object obj - 192.168.7.0
192.168.7.0 subnet 255.255.255.0
network object obj - 192.168.8.0
192.168.8.0 subnet 255.255.255.0
network object obj - 192.168.9.0
192.168.9.0 subnet 255.255.255.0
network object obj - 192.168.10.0
192.168.10.0 subnet 255.255.255.0
network object obj - 192.168.12.0
255.255.255.0 subnet 192.168.12.0
network object obj - 192.168.13.0
192.168.13.0 subnet 255.255.255.0
network object obj - 192.168.15.0
192.168.15.0 subnet 255.255.255.0
network object obj - 192.168.16.0
192.168.16.0 subnet 255.255.255.0
network object obj - 10.1.0.0
10.1.0.0 subnet 255.255.0.0
network object obj - 192.168.32.10
Home 192.168.32.10
network of the NETWORK_OBJ_192.168.20.0 object
host 192.168.20.0
network of the NETWORK_OBJ_192.168.20.0_24 object
subnet 192.168.20.0 255.255.255.0
network of the NETWORK_OBJ_192.168.3.0_24 object
subnet 192.168.3.0 255.255.255.0
network object obj - 192.168.0.0_16
Subnet 192.168.0.0 255.255.0.0
network of the NETWORK_OBJ_192.168.0.0_24 object
192.168.0.0 subnet 255.255.255.0network of the NETWORK_OBJ_192.168.3.0 object
host 192.168.3.0
network of the NETWORK_OBJ_192.168.3.144_28 object
subnet 192.168.3.144 255.255.255.240
network object obj - 192.168.50.11
network object obj - 192.168.30.10
host 192.168.30.10
network object obj - 192.168.40.10
Home 192.168.40.10
network object obj - 192.168.70.10
Home 192.168.70.10
network object obj - 192.168.150.10
Home 192.168.150.10
network object obj - 192.168.160.10
Home 192.168.160.10
network object obj - 10.10.10.10
host 10.10.10.10
network object obj - 192.168.120.10
Home 192.168.120.10access-list extended Out-In deny an ip
outside_1_cryptomap to access extended list ip 192.168.3.0 allow 255.255.255.0 192.168.0.0 255.255.255.0
pager lines 24
Enable logging
timestamp of the record
information recording console
registration of information monitor
debug logging in buffered memory
recording of debug trap
debugging in the history record
asdm of logging of informationOutside 1500 MTU
Within 1500 MTU
MTU 1500 DMZ - TNS
MTU 1500 DMZ-SMTP
cradelpoint MTU 1500no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP deny everything outside
ICMP deny any inside
ICMP deny all DMZ - TNSARP timeout 14400
NAT (inside, outside) static source any any static destination NETWORK_OBJ_192.168.3.144_28 NETWORK_OBJ_192.168.3.144_28 non-proxy-arp-search to itinerary
NAT (inside, outside) static source all all NETWORK_OBJ_192.168.0.0_24 of NETWORK_OBJ_192.168.0.0_24 static destination
!
network object obj - 172.16.3.2
NAT dynamic interface (indoor, outdoor)
network object obj - 172.16.7.2
NAT dynamic interface (indoor, outdoor)
network object obj - 172.16.10.2
NAT dynamic interface (indoor, outdoor)
network object obj - 172.16.13.2
NAT dynamic interface (indoor, outdoor)
network object obj - 192.168.3.0
NAT dynamic interface (indoor, outdoor)
network object obj - 192.168.4.0
NAT dynamic interface (indoor, outdoor)
network object obj - 192.168.5.0
NAT dynamic interface (indoor, outdoor)
network object obj - 192.168.6.0
NAT dynamic interface (indoor, outdoor)
network object obj - 192.168.7.0
NAT dynamic interface (indoor, outdoor)
network object obj - 192.168.8.0
NAT dynamic interface (indoor, outdoor)
network object obj - 192.168.9.0
NAT dynamic interface (indoor, outdoor)
network object obj - 192.168.10.0
NAT dynamic interface (indoor, outdoor)
network object obj - 192.168.12.0
NAT dynamic interface (indoor, outdoor)
network object obj - 192.168.13.0
NAT dynamic interface (indoor, outdoor)
network object obj - 192.168.15.0
NAT dynamic interface (indoor, outdoor)
network object obj - 192.168.16.0
NAT dynamic interface (indoor, outdoor)
network object obj - 10.1.0.0
NAT dynamic interface (indoor, outdoor)
network object obj - 192.168.32.10
NAT (DMZ-SMTP, outside) static 12.200.89.172
network object obj - 192.168.50.11Route outside 0.0.0.0 0.0.0.0 *. *. *. * 1
Route inside 10.1.0.0 255.255.0.0 192.168.3.1 1
Route inside 10.10.0.0 255.255.0.0 192.168.3.1 1
Route inside 10.200.0.0 255.255.0.0 192.168.3.1 1
Route inside 172.16.3.2 255.255.255.255 192.168.3.1 1
Route inside 172.16.7.2 255.255.255.255 192.168.3.1 1
Route inside 172.16.10.2 255.255.255.255 192.168.3.1 1
Route inside 172.16.13.2 255.255.255.255 192.168.3.1 1
Route inside 192.168.4.0 255.255.255.0 192.168.3.1 1
Route inside 192.168.5.0 255.255.255.0 192.168.3.1 1
Route inside 192.168.6.0 255.255.255.0 192.168.3.1 1
Route inside 192.168.7.0 255.255.255.0 192.168.3.1 1
Route inside 192.168.8.0 255.255.255.0 192.168.3.1 1
Route inside 192.168.9.0 255.255.255.0 192.168.3.1 1
Route inside 192.168.10.0 255.255.255.0 192.168.3.1 1
Route inside 192.168.12.0 255.255.255.0 192.168.3.1 1
Route inside 192.168.13.0 255.255.255.0 192.168.3.1 1
Route inside 192.168.15.0 255.255.255.0 192.168.3.1 1
Route inside 192.168.16.0 255.255.255.0 192.168.3.1 1
external route 192.168.20.0 255.255.255.0 *. *. *. * 1
Route inside 192.168.30.0 255.255.255.0 192.168.3.1 1
Route inside 192.168.40.0 255.255.255.0 192.168.3.1 1
Route inside 192.168.50.0 255.255.255.0 192.168.3.1 1
Route inside 192.168.70.0 255.255.255.0 192.168.3.1 1
Route inside 192.168.100.0 255.255.255.0 192.168.3.1 1
Route inside 192.168.120.0 255.255.255.0 192.168.3.1 1
Route inside 192.168.150.0 255.255.255.0 192.168.3.1 1
Route inside 192.168.160.0 255.255.255.0 192.168.3.1 1card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set peer 1.1.1.1
card crypto 1 ikev1 transform-set cradelpoint_vpn set outside_map
card crypto outside_map 1 the value reverse-road
outside_map interface card crypto outsideTelnet timeout 5
SSH timeout 5
Console timeout 0
management-access inside
a basic threat threat detection
host of statistical threat detection
statistical threat detection port
Statistical threat detection Protocol
Statistics-list of access threat detection
no statistical threat detection tcp-interception
NTP 10.1.2.13 Server prefer
SSL-trust outside ASDM_TrustPoint0 pointtunnel-group 1.1.1.1 type ipsec-l2l
tunnel-group 1.1.1.1 ipsec-attributes
IKEv1 pre-shared-key *.
!
class-map IPSclass
match any
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map IPSpolicy
class IPSclass
IPS inline help
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
class class by default
Statistical accounting of user
!Router config:
Current configuration: 2605 bytes
!
! Last modification of the configuration at 18:39:30 UTC Tuesday, August 7, 2012
! NVRAM config update at 19:50:03 UTC Monday, August 6, 2012
! NVRAM config update at 19:50:03 UTC Monday, August 6, 2012
version 15.1
horodateurs service debug datetime msec
Log service timestamps datetime msec!
router host name
!
boot-start-marker
boot-end-marker
!
!
activate the bonnefin password
!
No aaa new-model
!
!
No ipv6 cef
IP source-route
IP cef
!
!
!
!
!
name-server IP 192.168.100.1
!
Authenticated MultiLink bundle-name Panel
!
!
Crypto pki token removal timeout default 0
!!
!
!
redundancy
crypto ISAKMP policy 2
preshared authentication
address of crypto isakmp key 6 IBETYOUCANTGUESS *. *. *. *
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac cradelpoint_vpn
!
map SDM_CMAP_1 1 ipsec-isakmp crypto
Description Tunnel to *. *. *. *
set peer *. *. *. *
Set transform-set cradelpoint_vpn
match address 100
!
!
!
!
!
the Embedded-Service-Engine0/0 interface
no ip address
Shutdown
!
interface GigabitEthernet0/0
no ip addressShutdown
!
interface GigabitEthernet0/0
no ip address
IP nat inside
IP virtual-reassembly in
automatic duplex
automatic speed
No cdp enable
!
interface GigabitEthernet0/0.1
encapsulation dot1Q 1 native
the IP 192.168.0.1 255.255.255.0
IP nat inside
IP virtual-reassembly in
No cdp enable
!
interface GigabitEthernet0/0.2
encapsulation dot1Q 2
No cdp enable
!
interface GigabitEthernet0/0.3
encapsulation dot1Q 3
No cdp enable
!
interface GigabitEthernet0/1
DHCP IP address
automatic duplex
automatic speed
No cdp enable
map SDM_CMAP_1 crypto
!
interface Serial0/0/0
no ip address
Shutdown
no fair queue
!
IP forward-Protocol ND
!
no ip address of the http server
no ip http secure server
!
overload of IP nat inside source list 110 interface GigabitEthernet0/1
overload of IP nat inside source list sheep interface GigabitEthernet0/1
IP route 0.0.0.0 0.0.0.0 192.168.100.1 254
IP route 0.0.0.0 0.0.0.0 192.168.100.1 254
IP route 192.168.3.0 255.255.255.0 192.168.3.1
!
Access-list 100 = 4 SDM_ACL category note
Note access-list 100 IPSec rule
access-list 100 permit ip 192.168.0.0 0.0.0.255 192.168.3.0 0.0.0.255
access-list 110 deny ip 192.168.0.0 0.0.0.255 192.168.3.0 0.0.0.255
!
!
!
!
sheep allowed 10 route map
corresponds to the IP 110
!
!
!
control plan
!
!
!
Line con 0
line to 0
line 2
no activation-character
No exec
preferred no transport
transport of entry all
transport output pad rlogin lapb - your MOP v120 udptn ssh telnet
StopBits 1
line vty 0 4
opening of session
transport of entry all
!
Scheduler allocate 20000 1000
endAhh, looks like the CradelPoint router could have dropped the ESP package, as we can see the router is to encrypt the packets, but the ASA receives nothing / decrypts, which means it does not even reach the ASA.
Activate the NAT - T, so ESP is encapsulated in UDP/4500.
On ASA:
Crypto isakmp nat-traversal 30
-
Hi all
I'm trying to get a functional ASA 5505 appliance but does not always succeed. I managed to get connected to the ASA VPN client, but once connected, vpn client cannot access the internet. I am trying to route traffic from the client to the VPN server so I don't want to split tunneling. Here is the sketch of the testbed of the network:
DNS:210.193.2.66
|
|
Inside --------- Outside --------- -------------------
192.168.1.1 | | 202 *. *. 84 202.*. *. 1. | [ ]
---------------------- ASA |------------------------------------- GW |----------[ INTERNET ]
| | 5505. | | | [ ]
| | --------| | --------- -------------------
Host_A | 202.*. *. 83
192.168.1.5 -------------
| NetGear |
| Router |
--------------
| 192.168.2.1.
|
|
HOST_B |
Physical addr:192.168.2.2
Addr:192.168.3.1 VPNThe ASA 5505 config is as shown below:
Output from the command: 'show running-config '.
: Saved
:
ASA Version 8.2 (1)
!
ciscoasa hostname
activate 0cMYKRmmOdVhcSr4 encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 202.*. *. 84 255.255.255.128
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
inside_nat0_outbound list of allowed ip extended access any 192.168.3.0 255.255.255.224
pager lines 24
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
IP local pool vpnpool 192.168.3.1 - 192.168.3.20 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 202.128.171.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.1.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.128 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
enable client-implementation to date
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd outside auto_config
!
dhcpd address 192.168.1.5 - 192.168.1.20 inside
dhcpd dns 210.193.2.66 210.193.2.34 interface inside
dhcpd allow inside
!a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
Group Policy Reveal internal
Group Policy attributes Reveal
Protocol-tunnel-VPN IPSec
username password alice tnbrh7ICan8mnq/Y encrypted privilege 0
alice username attributes
Strategy Group-VPN-Reveal
tunnel-group Reveal type remote access
tunnel-group reveal General attributes
address vpnpool pool
Group Policy - by default-Reveal
tunnel-group show ipsec-attributes
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:bfb0083a8eb2416e9cc27befe3b224d9
: enda few thoughts
permit same-security-traffic intra-interface
NAT (outside) 1 your pool of vpn client
ASA sysopt connection permit VPN
ASA sysopt connection permit-ipsec
-
ISA500 site by site ipsec VPN with Cisco IGR
Hello
I tried a VPN site by site work with Openswan and Cisco 2821 router configuration an Ipsec tunnel to site by site with Cisco 2821 and ISA550.
But without success.
my config for openswan, just FYI, maybe not importand for this problem
installation of config
protostack = netkey
nat_traversal = yes
virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%4:!$RIGHT_SUBNET
nhelpers = 0
Conn rz1
IKEv2 = no
type = tunnel
left = % all
leftsubnet=192.168.5.0/24
right =.
rightsourceip = 192.168.1.2
rightsubnet=192.168.1.0/24
Keylife 28800 = s
ikelifetime 28800 = s
keyingtries = 3
AUTH = esp
ESP = aes128-sha1
KeyExchange = ike
authby secret =
start = auto
IKE = aes128-sha1; modp1536
dpdaction = redΘmarrer
dpddelay = 30
dpdtimeout = 60
PFS = No.
aggrmode = no
Config Cisco 2821 for dynamic dialin:
crypto ISAKMP policy 1
BA aes
sha hash
preshared authentication
Group 5
lifetime 28800
!
card crypto CMAP_1 1-isakmp dynamic ipsec DYNMAP_1
!
access-list 102 permit ip 192.168.1.0 0.0.0.255 192.168.5.0 0.0.0.255
!
Crypto ipsec transform-set ESP-AES-SHA1 esp - aes esp-sha-hmac
crypto dynamic-map DYNMAP_1 1
game of transformation-ESP-AES-SHA1
match address 102
!
ISAKMP crypto key
address 0.0.0.0 0.0.0.0 ISAKMP crypto keepalive 30 periodicals
!
life crypto ipsec security association seconds 28800
!
interface GigabitEthernet0/0.4002
card crypto CMAP_1
!
I tried ISA550 a config with the same constelations, but without suggesting.
Anyone has the same problem?
And had anyone has a tip for me, or has someone expirense with a site-by-site with ISA550 and Cisco 2821 ipsec tunnel?
I can successfully establish a tunnel between openswan linux server and the isa550.
Patrick,
as you can see on newspapers, the software behind ISA is also OpenSWAN
I have a facility with a 892 SRI running which should be the same as your 29erxx.
Use your IOS Config dynmap, penny, you are on the average nomad. If you don't have any RW customer you shoul go on IOS "No.-xauth" after the isakmp encryption key.
Here is my setup, with roardwarrior AND 2, site 2 site.
session of crypto consignment
logging crypto ezvpn
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
lifetime 28800
!
crypto ISAKMP policy 2
BA 3des
md5 hash
preshared authentication
Group 2
lifetime 28800
!
crypto ISAKMP policy 3
BA 3des
preshared authentication
Group 2
!
crypto ISAKMP policy 4
BA 3des
md5 hash
preshared authentication
Group 2
!
crypto ISAKMP policy 5
BA 3des
preshared authentication
Group 2
life 7200
ISAKMP crypto address XXXX XXXXX No.-xauth key
XXXX XXXX No.-xauth address isakmp encryption key
!
ISAKMP crypto client configuration group by default
key XXXX
DNS XXXX
default pool
ACL easyvpn_client_routes
PFS
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac FEAT
!
dynamic-map crypto VPN 20
game of transformation-FEAT
market arriere-route
!
!
card crypto client VPN authentication list by default
card crypto VPN isakmp authorization list by default
crypto map VPN client configuration address respond
10 VPN ipsec-isakmp crypto map
Description of VPN - 1
defined peer XXX
game of transformation-FEAT
match the address internal_networks_ipsec
11 VPN ipsec-isakmp crypto map
VPN-2 description
defined peer XXX
game of transformation-FEAT
PFS group2 Set
match the address internal_networks_ipsec2
card crypto 20-isakmp dynamic VPN ipsec VPN
!
!
Michael
Please note all useful posts
Maybe you are looking for
-
30 Firefox does not open new windows maximized
I use Firefox on 2 machines, one at home and one at work. I have updated all the two to 30 of Firefox. My machine at home, with Windows 7 opens new windows maximized. However, my work machine, will not open new windows maximized. It will open them on
-
Envy of 4-1152er, PN: COU74EA #ACB: replace want 4 HDD to SSD
Hello. Please notice, is it possible to replace the drive HARD Hitachi HTS545050A7E380 of exisitng for, lets say, Kingston SSDNow V300 240GB 2.5 SSD "SATAIII MLC (SV300S37A / 240G) or even another drive? Thank you.
-
Downgrade from windows XP Professional vista OEM
If I want to downgrade my windows XP Professional vista OEM, I fill in key windows xp product of google search,.It will be illegal?
-
How can I omit logon and automatically go directly on my desk?
original title: logon... How can I omit logon and automatically go directly on my desk?
-
-MultimediaDemo - sample.MP4 (n00b) could not be found
Hello! I'm a n00b here, so please forgive the stupid question... I'm trying to get the sample working MultimediaDemo, and I am pulling my hair out trying to get the Simulator to find the sample.mp4 file. When I debug I get error: CAFETERIA: sample.mp