VPN with PIX 501

Help!

I'm trying to set up VPN on my PIX 501. I have no experience of the PIX and have no idea where to start!

Any help will be greatly appreciated.

Thank you

Bennie

access list allow accord a

where is the name of the access list that you applied the entrants to your external interface. You may also allow accord coming out, if you have a list of incoming configured access to your inside interface.

Tags: Cisco Security

Similar Questions

  • Problems with PIX 501 and Server MS Cert

    Hi all

    I have two problems with my PIX 501:

    1. registration works well. The pix has a certificate and use it with SSL and VPN connections. But after a refill, the pix certificate is lost and it has regenerated again self-signed certificate!

    Yes, I wrote mem and ca records all!

    2. at the request of ca CRL , I get the following debugging:

    Crypto CA thread wakes!

    CRYPTO_PKI: Cannot be named County ava

    CRYPTO_PKI: transaction GetCRL completed

    Crypto CA thread sleeps!

    CI thread wakes!

    And the CRL is empty.

    Does anyone have any idea?

    Bert Koelewijn

    Not sure about 1, but 2 is usually caused by the COP (Point of Distribution of CRL, basically the situation where the PIX can download the Revocation list from) listed in cert CA is in a format the PIX does not, generally an LDAP URL.

    Check the following prayer:

    Open the administration tool of CA (Certification Authority) then

    (1) right click on the name of CA and choose 'properties '.

    2) click on the tab "Policy Module".

    3) click on the button "configure."

    4) click on the tab "X.509 extensions".

    > From there, it can display the list of the "CRL Distribution Points".

    Turn off everything that isn't HTTP.

    You need to reinstall the CERT in the PIX, I think, but then it should be able to download the CRL through HTTP instead of LDAP.

  • Remote VPN with PIX without access to the local network

    Hi @all,

    I ve running into problems and I have not found any solution. Can someone check my config?

    Facts:

    PIX 501 6.3 (3)

    4.04 VPN client

    Wanted solution: access to HO via VPN

    VPN tunnel will be established, I get an IP address, but I can´t the systems behind the pix and the pix of access itself.

    To the VPN Client Staticts, I see outgoing packets, but no entrant (if I send a ping to peer behind the pix)

    I hope someone can help me

    Attached is my config:

    PIX 501 and 506/506e pix are not supported in v7 due to the fact that the cpu is not able to deal with the extended features of v7.

    PIX 520 is not supported I guess it's because of the fact that the model is discontinued.

  • Port forwarding with PIX 501

    I try to get my PIX 501 to forward traffic on port 1412 with TCP and UDP to use Direct Connect, and the problem I have is I can connect to a DC hub, but cannot establish connections with users.

    I added the following to the default configuration from the factory with a partial success:

    outside access list permit tcp any host 192.168.100.20 eq 1412

    access-list outside permit udp any host 192.168.100.20 eq 1412

    public static tcp (indoor, outdoor) interface 1412 192.168.100.20 1412 netmask 255.255.255.255 0 0

    public static tcp (indoor, outdoor) interface 1412 192.168.100.20 1412 netmask 255.255.255.255 0 0

    In the debug log set to the access list I rule this type of errors:

    Deny tcp src outside other.users.ip.addr/3099 dst within the my.public.ip.addr/1412 by access-group "access_outside_in".

    TCP request discarded outside my.public.ip.addr/45961 other.users.ip.addr/2362

    I'm quite lost as to why it does not work when I think it should. I tried several ways, opening of port ranges and no chance for a transfer of the port sucsessful.

    You can change you, outside the ACL to the following:

    outside access list permit tcp any host eq 1412

    access-list outside permit udp any host eq 1412

    outside access-group in external interface

    Save again with: write mem and also issue: clear xlate

    I would like to know if it works.

    Jay

  • Problem with PIX 501-> L2L 1721 VPN

    I am setting up a site to site vpn according to the http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a008051a69a.shtml.

    I want to connect 192.168.105.0/24 and 192.168.106.0/24.

    PIX01 is 192.168.106.1, with dynamic external IP (B.B.B.B)

    RTR01 is 192.168.105.1, with dynamic external IP address (I'm just using DHCP current address of the ISP as A.A.A.A in the config of PIX01 - this is a temporary application, not critical where I can update the address if necessary)

    It seems that the VPN tunnel is established but traffic does not return the router to the pix.  I temporarily hosted all of the traffic on indoor/outdoor PIX interfaces (and icmp).

    If I enable icmp debug I see ping requests from the client to 192.168.106.100 internal interface of the router (192.168.105.1), but no return icmp:

    On PIX01:

    180:-Interior ICMP echo request: 192.168.105.1 ID = 1 length = 40 seq = 298 192.168.106.100
    181:-Interior ICMP echo request: 192.168.105.1 ID = 1 length = 40 seq = 299 192.168.106.100
    182:-Interior ICMP echo request: 192.168.105.1 ID = 1 length = 40 seq = 300 192.168.106.100
    183:-Interior ICMP echo request: 192.168.105.1 ID = 1 seq = length 301 = 40 192.168.106.100

    On RTR01:
    * 03:40:46.885 22 dec: ICMP: echo responded, 192.168.105.1 src, dst 192.168.106.100
    * 03:40:51.713 22 dec: ICMP: echo responded, 192.168.105.1 src, dst 192.168.106.100
    * 03:40:56.713 22 dec: ICMP: echo responded, 192.168.105.1 src, dst 192.168.106.100
    * 03:41:01.709 22 dec: ICMP: echo responded, 192.168.105.1 src, dst 192.168.106.100

    Output of running sh crypto isakmp his:

    PIX01 (config) # sh crypto isakmp his
    Total: 1
    Embryonic: 0
    Src DST in the meantime created State
    A.A.A.A B.B.B.B 0 1 QM_IDLE

    RTR01 #sh crypto isakmp his
    status of DST CBC State conn-id slot
    A.A.A.A B.B.B.B QM_IDLE 1 0 ACTIVE

    Out of HS crypto ipsec his:

    PIX01 (config) # sh crypto ipsec his

    Interface: outside
    Crypto map tag: IPSEC, local addr. B.B.B.B

    local ident (addr, mask, prot, port): (192.168.106.0/255.255.255.0/0/0)
    Remote ident (addr, mask, prot, port): (192.168.105.0/255.255.255.0/0/0)
    current_peer: A.A.A.A:500
    LICENCE, flags is {origin_is_acl},
    #pkts program: 103, #pkts encrypt: collection of #pkts 103, 103
    #pkts decaps: 0, #pkts decrypt: 0, #pkts check 0
    compressed #pkts: 0, unzipped #pkts: 0
    #pkts uncompressed: 0, #pkts compr. has failed: 0, #pkts decompress failed: 0
    #send 12, #recv errors 0

    local crypto endpt. : B.B.B.B, remote Start crypto. : A.A.A.A
    Path mtu 1500, overload ipsec 56, media, mtu 1500
    current outbound SPI: 7cb75998

    SAS of the esp on arrival:
    SPI: 0xb896f6c6 (3096901318)
    transform: esp - esp-md5-hmac.
    running parameters = {Tunnel}
    slot: 0, conn id: 1, crypto card: IPSEC
    calendar of his: service life remaining (k/s) key: (4608000/3151)
    Size IV: 8 bytes
    support for replay detection: Y

    the arrival ah sas:

    SAS of the CFP on arrival:

    outgoing esp sas:
    SPI: 0x7cb75998 (2092390808)
    transform: esp - esp-md5-hmac.
    running parameters = {Tunnel}
    slot: 0, conn id: 2, crypto card: IPSEC
    calendar of his: service life remaining (k/s) key: (4607999/3151)
    Size IV: 8 bytes
    support for replay detection: Y

    outgoing ah sas:

    outgoing CFP sas:

    RTR01 #sh crypto ipsec his

    Interface: Vlan600
    Crypto map tag: IPSEC, local addr A.A.A.A

    protégé of the vrf: (none)
    local ident (addr, mask, prot, port): (192.168.105.0/255.255.255.0/0/0)
    Remote ident (addr, mask, prot, port): (192.168.106.0/255.255.255.0/0/0)
    current_peer B.B.B.B port 500
    LICENCE, flags is {}
    program #pkts: 10, #pkts encrypt: 10, #pkts digest: 10
    decaps #pkts: 10, #pkts decrypt: 10, #pkts check: 10
    compressed #pkts: 0, unzipped #pkts: 0
    #pkts uncompressed: 0, #pkts compr. has failed: 0
    #pkts not unpacked: 0, #pkts decompress failed: 0
    Errors #send 0, #recv 0 errors

    local crypto endpt. : A.A.A.A, remote Start crypto. : B.B.B.B
    Path mtu 1500, mtu 1500 ip, ip mtu BID Vlan600
    current outbound SPI: 0xB896F6C6 (3096901318)

    SAS of the esp on arrival:
    SPI: 0x7CB75998 (2092390808)
    transform: esp - esp-md5-hmac.
    running parameters = {Tunnel}
    Conn ID: 2002, flow_id: SW:2, crypto card: IPSEC
    calendar of his: service life remaining (k/s) key: (4556997/3076)
    Size IV: 8 bytes
    support for replay detection: Y
    Status: ACTIVE

    the arrival ah sas:

    SAS of the CFP on arrival:

    outgoing esp sas:
    SPI: 0xB896F6C6 (3096901318)
    transform: esp - esp-md5-hmac.
    running parameters = {Tunnel}
    Conn ID: 2001, flow_id: SW:1, crypto card: IPSEC
    calendar of his: service life remaining (k/s) key: (4556997/3076)
    Size IV: 8 bytes
    support for replay detection: Y
    Status: ACTIVE

    outgoing ah sas:

    outgoing CFP sas:

    I can provide more information if necessary.

    Thanks in advance for any help,

    CJ

    ISAKMP uses UDP/500 and it is true he helped through phase 1 being upwards (QM_IDLE).

    IPSec uses ESP or UDP/4500, and this is what must be authorized by the FW.

  • client vpn Cisco pix 501

    I wonder and wonder, is it possible for a branch (2 vpn clients) to connect to the central location (cisco 501 pix) at the same time via the vpn client with a public address on each side. If this is not the case, what will be the way to make it work without additional equipment (another pix of cisco).

    Yes you can, you should check your os 6.3 a pix and you enable nat-transapency: -.

    ISAKMP nat-traversal 20

  • site to site vpn with pix multiple tunnels

    Hello

    I have a vpn site-to-site between two PIX firewall tunnel.

    Is it possible to build on one side, another tunnel vpn site to site with the third PIX?

    Thank you

    Robert

    Robert

    You can use one card encryption on an interface, but you may have within your crypto card so your config sequence numbers

    The existing tunnel

    mykink1 card crypto ipsec isakmp 1

    correspondence address 1 card crypto mykink1 101

    mykink1 card crypto 1jeu peer 21.21.21.21

    mykink1 card crypto 1 set transform-set aesonly

    Your new tunnel

    mykink1 map ipsec-isakmp crypto 2

    card crypto mykink1 game 2 address "LCD number".

    mykink1 crypto map peer set 2 "new peer address.

    card crypto mykink1 2 the value transform-set "new transform set.

    card crypto mykink1 2 security association second life "number of seconds.

    You must complete the good values in the "" marks.

    Note that the sequence number is incremented by 1 in your first entry for 2 in the second entry.

    You can specify the duration of security association in the crypto map config that overrides the global settings.

    Add this config should not affect your existing tunnel.

    HTH

    Jon

  • Problem of recovery of password with pix 501

    Hello

    my organization uses a firewall 501 pix with version 6.2 of the software. After I lost the password I tried earasing using the faq provided on this site (using the file np62.bin through a TFTP server).

    Unfortunately, I can not connect using the password default "cisco."

    Thank you

    Raphaël Cohen, University of Tel Aviv

    Hello Raphael,.

    You need to connect to the PIX via the port on the PIX console. If you deleted the passwords, then (as mentioned before), there is NO password to access privileged EXEC access just don't hit back, now, you will need to configure a password to "enable" with command > pix # enable password - the password is case-sensitive and can be a combination of characters and numbers the length of the password is limited to 16 characters.

    You can now set access telnet as well i.e. config mode > pix (config) # telnet [masque_sous] [interface_name]

    example: (in config mode) telnet 192.168.10.10 255.255.255.0 inside

    Good idea to use the static IP address for the above, makesure to save your config with cmd: write memory

    Hope this helps - Jay

    PS. Thanks to vote this post if it helped you so that other members can use it if they have the same problem you have - that helps! Thank you.

  • Help the Site VPN Site PIX 501

    Hello

    I'm pretty new to PIX firewall, so I hope someone here can help me.

    I have two PIX and try to create a private network virtual between the two PIX. I posted the configs below.

    The problem is that I can ping PIX on a PIX two, but I can't ping the servers behind TWO PIX. On two PIX, I cannot ping PIX ONE or all the servers behind it.

    Any advice would be appreciated.

    Thank you

    PIX 1

    6.2 (2) version PIX

    ethernet0 nameif outside security0

    nameif ethernet1 inside the security100

    hostname TMAXWALES

    domain ciscopix.com

    fixup protocol ftp 21

    fixup protocol http 80

    fixup protocol h323 h225 1720

    fixup protocol h323 ras 1718-1719

    fixup protocol they 389

    fixup protocol rsh 514

    fixup protocol rtsp 554

    fixup protocol smtp 25

    fixup protocol sqlnet 1521

    fixup protocol sip 5060

    fixup protocol 2000 skinny

    names of

    inside_outbound_nat0_acl ip 192.168.254.0 access list allow 255.255.255.0 192.1

    68.1.0 255.255.255.0

    outside_cryptomap_20 ip 192.168.254.0 access list allow 255.255.255.0 192.168.1

    .0 255.255.255.0

    pager lines 24

    interface ethernet0 10baset

    interface ethernet1 10full

    Outside 1500 MTU

    Within 1500 MTU

    IP address outside of *. *.198.139 255.255.255.248

    IP address inside 192.168.254.1 255.255.255.0

    alarm action IP verification of information

    alarm action attack IP audit

    location of PDM 192.168.254.10 255.255.255.255 inside

    location of PDM 192.168.1.0 255.255.255.0 outside

    history of PDM activate

    ARP timeout 14400

    Global 1 interface (outside)

    NAT (inside) 0-list of access inside_outbound_nat0_acl

    NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

    Route outside 0.0.0.0 0.0.0.0 *. * 1.198.137

    Timeout xlate 03:00

    Timeout conn 0 half-closed 01:00:10: 00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 TR

    p 0:30:00 sip_media 0:02:00

    Timeout, uauth 0:05:00 absolute

    GANYMEDE + Protocol Ganymede + AAA-server

    RADIUS Protocol RADIUS AAA server

    AAA-server local LOCAL Protocol

    Enable http server

    http 192.168.254.10 255.255.255.255 inside

    No snmp server location

    No snmp Server contact

    SNMP-Server Community public

    No trap to activate snmp Server

    enable floodguard

    Permitted connection ipsec sysopt

    No sysopt route dnat

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    outside_map 20 ipsec-isakmp crypto map

    card crypto outside_map 20 match address outside_cryptomap_20

    card crypto outside_map 20 peers set *. *.198.138

    outside_map crypto 20 card value transform-set ESP-3DES-SHA

    outside_map interface card crypto outside

    ISAKMP allows outside

    ISAKMP key * address *. *.198.138 netmask 255.255.255.255 No.-xauth non - co

    Nfig-mode

    part of pre authentication ISAKMP policy 20

    ISAKMP policy 20 3des encryption

    ISAKMP policy 20 chopping sha

    20 2 ISAKMP policy group

    ISAKMP duration strategy of life 20 86400

    Telnet timeout 5

    SSH timeout 5

    Terminal width 80

    PIX 2

    6.2 (2) version PIX

    ethernet0 nameif outside security0

    nameif ethernet1 inside the security100

    hostname tmaxbangor

    domain ciscopix.com

    fixup protocol ftp 21

    fixup protocol http 80

    fixup protocol h323 h225 1720

    fixup protocol h323 ras 1718-1719

    fixup protocol they 389

    fixup protocol rsh 514

    fixup protocol rtsp 554

    fixup protocol smtp 25

    fixup protocol sqlnet 1521

    fixup protocol sip 5060

    fixup protocol 2000 skinny

    names of

    permit 192.168.1.0 ip access list inside_outbound_nat0_acl 255.255.255.0 192.168

    . 254.0 255.255.255.0

    permit 192.168.1.0 ip access list outside_cryptomap_20 255.255.255.0 192.168.254

    .0 255.255.255.0

    pager lines 24

    opening of session

    debug logging in buffered memory

    interface ethernet0 10baset

    interface ethernet1 10full

    Outside 1500 MTU

    Within 1500 MTU

    IP address outside of *. *.198.138 255.255.255.248

    IP address inside 192.168.1.1 255.255.255.0

    IP verify reverse path to the outside interface

    IP verify reverse path inside interface

    the IP audit info action alarm reset drop

    reset the IP audit attack alarm drop action

    location of PDM 192.168.1.0 255.255.255.0 inside

    PDM logging 100 information

    history of PDM activate

    ARP timeout 14400

    Global 1 interface (outside)

    NAT (inside) 0-list of access inside_outbound_nat0_acl

    NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

    Route outside 0.0.0.0 0.0.0.0 *. * 1.198.137

    Timeout xlate 03:00

    Timeout conn 0 half-closed 01:00:10: 00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 TR

    p 0:30:00 sip_media 0:02:00

    Timeout, uauth 0:05:00 absolute

    GANYMEDE + Protocol Ganymede + AAA-server

    RADIUS Protocol RADIUS AAA server

    AAA-server local LOCAL Protocol

    Enable http server

    http 192.168.1.0 255.255.255.0 inside

    http 192.84.7.111 255.255.255.255 inside

    http 192.168.1.10 255.255.255.255 inside

    No snmp server location

    No snmp Server contact

    SNMP-Server Community public

    No trap to activate snmp Server

    enable floodguard

    Permitted connection ipsec sysopt

    No sysopt route dnat

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    outside_map 20 ipsec-isakmp crypto map

    card crypto outside_map 20 match address outside_cryptomap_20

    card crypto outside_map 20 peers set *. *.198.139

    outside_map crypto 20 card value transform-set ESP-3DES-SHA

    outside_map interface card crypto outside

    ISAKMP allows outside

    ISAKMP key * address *. *.198.139 netmask 255.255.255.255 No.-xauth non - co

    Nfig-mode

    part of pre authentication ISAKMP policy 20

    ISAKMP policy 20 3des encryption

    ISAKMP policy 20 chopping sha

    20 2 ISAKMP policy group

    ISAKMP duration strategy of life 20 86400

    Telnet 192.168.1.0 255.255.255.0 inside

    Telnet timeout 50

    SSH timeout 5

    Terminal width 80

    Can't see anything obviously wrong with the configs. You have these connected back to back on the same subnet, it looks that it even if you have xxx out IP addresses? If so it's maybe a routing problem, in what they send everything to the default gateway of xxx.x.198.137 rather than to the other.

    Try to add a static route to the remote subnet to each PIX that points directly to the peer, so on PIX1 you should have:

    Route outside 192.168.1.0 255.255.255.0 xxx.x.198.138

    and on PIX2 do:

    Route outside 192.168.254.0 255.255.255.0 xxx.x.198.139

    and see if that makes a difference. Note that you wouldn't encounter this problem when these two PIX is on separate networks and uses the default gateway for all routing decisions.

    If this still fails, run 'debug cryp isa' and ' debug cry ipsec "on the two PIX are trying to build a tunnel again, and then and send us the output.

    Also, make sure your tests that you're rattling to a host behind a PIX to a host behind the other PIX, ping PIX to PIX or host because of PIX that won't test your VPN connection.

  • Save the password on the Client VPN with PIX

    I'm running a PIX 515 6.1 (2) configured for a small number of VPN clients. I want VPN clients to automatically remember the password of login for users do not have to enter it each time (we have an application which periodically autoconnexions).

    While it is a configurable option with concentrators 3000 series, it seems not be configurable with the PIX.

    The only work around, I can find is to make the connection file (.pcf) read-only and set SaveUserPassword = 1. The problem

    which is the password, and then must be stored in clear text in the file and it becomes inconvenient for the user to change their password.

    Does anyone know if the command exists on the PIX from the VPN client to save the connection password?

    Thank you

    Misha

    The command to do this is not currently available on the PIX. He has just been included in the IOS EZVPN server functionality, but have not heard of anything anyone yet as to if it will be included in the PIX.

    If you want this feature, do not hesitate to contact your account manager and have them grow for him, the more customers requesting a new feature faster he gets.

  • Cisco ASA 5510 VPN with PIX 515

    Hello

    I have VPN between Cisco ASA and Cisco PIX.

    I saw in my syslog server this error that appears once a day, more or less:

    Received a package encrypted with any HIS correspondent, drop

    I ve seen issue in another post, but in none of then the solution.

    Here are my files from the firewall configuration:

    Output from the command: 'show running-config '.

    : Saved
    :
    ASA Version 8.2 (1)
    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
    life crypto ipsec security association seconds 28800
    Crypto ipsec kilobytes of life - safety 4608000 association
    card crypto WAN_map2 2 corresponds to the address WAN_cryptomap_1
    card crypto WAN_map2 2 set pfs
    card crypto WAN_map2 2 peer 62.80.XX game. XX
    map WAN_map2 2 game of transformation-ESP-DES-MD5 crypto
    card crypto WAN_map2 2 defined security-association 2700 seconds life
    card crypto WAN_map2 2 set nat-t-disable
    card crypto WAN_map2 WAN interface
    enable LAN crypto ISAKMP
    ISAKMP crypto enable WAN
    crypto ISAKMP policy 1
    preshared authentication
    the Encryption
    md5 hash
    Group 5
    lifetime 28800
    No encryption isakmp nat-traversal
    tunnel-group 62.80.XX. XX type ipsec-l2l
    tunnel-group 62.80.XX. IPSec-attributes of XX
    pre-shared-key *.

    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

    8.0 (4) version PIX
    !
    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
    life crypto ipsec security association seconds 28800
    Crypto ipsec kilobytes of life - safety 4608000 association
    card encryption VPN_map2 3 corresponds to the address VPN_cryptomap_2
    card encryption VPN_map2 3 set pfs
    card crypto VPN_map2 3 peer 194.30.XX game. XX
    VPN_map2 3 transform-set ESP-DES-MD5 crypto card game
    card encryption VPN_map2 3 defined security-association life seconds 2700
    card encryption VPN_map2 3 set security-association kilobytes of life 4608000
    card VPN_map2 3 set nat-t-disable encryption
    VPN crypto map VPN_map2 interface
    crypto ISAKMP enable VPN
    crypto ISAKMP allow inside
    crypto ISAKMP policy 30
    preshared authentication
    the Encryption
    md5 hash
    Group 5
    lifetime 28800
    No encryption isakmp nat-traversal
    ISAKMP crypto am - disable
    attributes of Group Policy DfltGrpPolicy
    Protocol-tunnel-VPN IPSec
    tunnel-group 194.30.XX. XX type ipsec-l2l
    tunnel-group 194.30.XX. IPSec-attributes of XX
    pre-shared-key *.

    If you need more information dedailed ask me questions.

    Thanks in advance for your help.

    Javi

    Hi Javi,

    Please after the release of "see broadcasting DfltGrpPolicy of any political group." See if you have the "vpn-idle-timoeout" command configured in that. If so, please change to "vpn-idle-timeout no" and see if that stops at these popping up error messages.

    http://www.Cisco.com/en/us/docs/security/ASA/asa80/command/reference/uz.html#wp1571426

    Thank you and best regards,

    Assia

  • Cannot access the internal network of VPN with PIX 506th

    Hello

    I seem to have a problem with the configuration of my PIX. I ping the VPN client from the network in-house, but cannot cannot access all the resources of the vpn client. My running configuration is the following:

    Building configuration...

    : Saved

    :

    6.3 (5) PIX version

    interface ethernet0 car

    Auto interface ethernet1

    ethernet0 nameif outside security0

    nameif ethernet1 inside the security100

    activate the encrypted password of N/JZnmeC2l5j3YTN

    2KFQnbNIdI.2KYOU encrypted passwd

    hostname SwantonFw2

    domain name * *.com

    fixup protocol dns-length maximum 512

    fixup protocol ftp 21

    fixup protocol h323 h225 1720

    fixup protocol h323 ras 1718-1719

    fixup protocol http 80

    fixup protocol rsh 514

    fixup protocol rtsp 554

    fixup protocol sip 5060

    fixup protocol sip udp 5060

    fixup protocol 2000 skinny

    fixup protocol smtp 25

    fixup protocol sqlnet 1521

    fixup protocol tftp 69

    names of

    access-list outside_access_in allow icmp a whole

    allow_ping list access permit icmp any any echo response

    allow_ping list all permitted access all unreachable icmp

    access-list allow_ping allow icmp all once exceed

    the INSIDE-IN access list allow inside the interface tcp interface outside

    list access to the INSIDE-IN permit udp any any eq field

    list access to the INSIDE-IN permit tcp any any eq www

    list access to the INSIDE-IN permit tcp any any eq ftp

    list access to the INSIDE-IN permit icmp any any echo

    the INSIDE-IN permit tcp access list everything all https eq

    permit access ip 192.168.0.0 list inside_outbound_nat0_acl 255.255.255.0 192.168.240.0 255.255.255.0

    swanton_splitTunnelAcl ip access list allow a whole

    outside_cryptomap_dyn_20 ip access list allow any 192.168.240.0 255.255.255.0

    no pager

    Outside 1500 MTU

    Within 1500 MTU

    192.168.1.150 outside IP address 255.255.255.0

    IP address inside 192.168.0.35 255.255.255.0

    alarm action IP verification of information

    alarm action attack IP audit

    IP pool local VPN_Pool 192.168.240.1 - 192.168.240.254

    location of PDM 0.0.0.0 255.255.255.0 outside

    location of PDM 192.168.1.26 255.255.255.255 outside

    location of PDM 192.168.240.0 255.255.255.0 outside

    PDM logging 100 information

    history of PDM activate

    ARP timeout 14400

    Global 1 interface (outside)

    NAT (inside) 0-list of access inside_outbound_nat0_acl

    NAT (inside) 1 192.168.0.0 255.255.255.0 0 0

    Access-group outside_access_in in interface outside

    group-access INTERIOR-IN in the interface inside

    Route outside 0.0.0.0 0.0.0.0 192.168.1.1 1

    Timeout xlate 0:05:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

    H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

    Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00

    Timeout, uauth 0:05:00 absolute

    GANYMEDE + Protocol Ganymede + AAA-server

    AAA-server GANYMEDE + 3 max-failed-attempts

    AAA-server GANYMEDE + deadtime 10

    RADIUS Protocol RADIUS AAA server

    AAA-server RADIUS 3 max-failed-attempts

    AAA-RADIUS deadtime 10 Server

    AAA-server local LOCAL Protocol

    Enable http server

    http 192.168.0.0 255.255.255.0 inside

    No snmp server location

    No snmp Server contact

    SNMP-Server Community public

    No trap to activate snmp Server

    enable floodguard

    Permitted connection ipsec sysopt

    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

    Dynamic crypto map outside_dyn_map 20 match address outside_cryptomap_dyn_20

    Crypto-map dynamic outside_dyn_map 20 the transform-set ESP-DES-MD5 value

    map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

    client authentication card crypto outside_map LOCAL

    outside_map interface card crypto outside

    ISAKMP allows outside

    ISAKMP identity address

    part of pre authentication ISAKMP policy 20

    encryption of ISAKMP policy 20

    ISAKMP policy 20 md5 hash

    20 2 ISAKMP policy group

    ISAKMP duration strategy of life 20 86400

    Swanton vpngroup address pool VPN_Pool

    vpngroup swanton 192.168.1.1 dns server

    vpngroup swanton splitting swanton_splitTunnelAcl tunnel

    vpngroup idle 1800 swanton-time

    swanton vpngroup password *.

    Telnet timeout 5

    SSH timeout 5

    Console timeout 0

    dhcpd address 192.168.0.36 - 192.168.0.254 inside

    dhcpd dns 8.8.8.8 8.8.4.4

    dhcpd lease 3600

    dhcpd ping_timeout 750

    dhcpd outside auto_config

    dhcpd allow inside

    scott hwDnqhIenLiwIr9B of encrypted privilege 15 password username

    username password encrypted ET3skotcnISwb3MV privilege 2 norm

    username password tarmbrecht Zre8euXN6HxXaSdE encrypted privilege 2

    username, password jlillevik 9JMTvNZm3dLhQM/W encrypted privilege 2

    username privilege 15 encrypted password 49ikl05C8VE6k1jG ruralogic

    username bzeiter 1XjpdpkwnSENzfQ0 encrypted password privilege 2

    name of user mwalla encrypted password privilege 2 l5frk9obrNMGOiOD

    username heavyfab1 6.yy0ys7BifWsa9k encrypted password privilege 2

    username heavyfab3 6.yy0ys7BifWsa9k encrypted password privilege 2

    username heavyfab2 6.yy0ys7BifWsa9k encrypted password privilege 2

    username djet encrypted password privilege 2 wj13fSF4BPQzUzB8

    username, password cmorgan y/NeUfNKehh/Vzj6 encrypted privilege 2

    username password cmayfield Pe/felGx7VQ3I7ls encrypted privilege 2

    username privilege 2 encrypted password zQEQceRITRrO4wJa jeffg

    Terminal width 80

    Cryptochecksum:9005f35a85fa5fe31dab579bbb1428c8

    : end

    [OK]

    Any help will be greatly appreciated

    BJ,

    You try to access resources behind the inside interface network?

    IP address inside 192.168.0.35 255.255.255.0

    If so, please make the following changes:

    1 SWANTON_VPN_SPLIT permit access ip 192.168.0.0 list 255.255.255.0 192.168.240.0 255.255.255.0

    2-no vpngroup swanton splitting swanton_splitTunnelAcl tunnel

    Swanton vpngroup split tunnel SWANTON_VPN_SPLIT

    outside_cryptomap_dyn_20 3-no-list of ip access allowing any 192.168.240.0 255.255.255.0

    4 - isakmp nat-traversal 30

    Let me know how it goes.

    Portu.

    Please note all useful posts

  • VPN with ASA 5500 VPN with PIX 515E vs

    I wonder what are the differences between the use of an exisitng PIX 515E for VPN remote users as appossed to acquire an ASA 5500 VPN remote users? Information or advice are appreciated to help me lean toward one or the other.

    Craig

    According to the version of the code that you run on the PIX on the PIX or ASA VPN features must be the same. So if the choice is not based on differences in features, what else would help guide the choice? You can consider if the existing PIX has sufficient resources to add the extra processing VPN load or if you should put that on another box. You might consider that the PIX is an older product range, and his end is near, while the ASA is the product that is the strategic replacement for the PIX. Given a choice I probably prefer to use a technology newer than the old technology. I also believe that the ASA will give you more choice of technology to go forward (a way of better growth) while the PIX provides current capacity but no path of growth.

    On the other hand, there is the aspect of consider that using the existing PIX does not need not to buy something new and ASA would be an expense you have to cover in the budget. And for some people the budget constraint is an important consideration.

    HTH

    Rick

  • VPN between cisco unified customer 3.6.3 and Pix 501 6.2 (1) with the MS CA server

    Hello

    I have Microsoft CA server with the latest support CEP and pix 501 that gets the digital certificate. I also have the client certificate of Cisco, but VPN doesn't work

    In the IPSec Log Viewer, I constantly "CM_IKE_ESTABLISH_FAIL."

    It worked well prior to Win2k server has been completely updated with the latest patches.

    The pix configuration is identical to that of article http://www.cisco.com/warp/public/471/configipsecsmart.html

    I reinstall the stand-alone CA and support CEP server but not had any luck.

    What could be wrong?

    It looks like IKE implementation problem. Make DH group 2 policy ISAKMP.

    Visit this link:

    http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_v53/IPSec/exvpncl.htm

  • VPN site-to-site between two PIX 501 with Client VPN access

    Site A and site B are connected with VPN Site to Site between two PIX 501.

    Also, site A is configured for remote access VPN client. If a remote client connects to Site A, it can only get access to the LAN of Site A, it cannot access anything whatsoever behind PIX on Site B.

    How is that possible for a VPN client connected to Site A to Site B?

    Thank you very much.

    Alex

    Bad and worse news:

    Bad: Not running the 7.0 series PIX cannot route traffic on the same interface, the traffic is recived. Version 7.0 solves this ipsec traffic.

    Even worse: PIX 501 can not be upgraded to 7.0...

    A couple of things to think about would be the upgrade to hardware that can run the new IOS or allowing a VPN R.A. on site B.

    HTH Please assess whether this is the case.

    Thank you

Maybe you are looking for