waiting for reset in case structure and

Similar Questions

• Resetting a case Structure

  The goal is to fill two tanks, one after the other. When the first tank reaches 90, must emit red light, and the second reservoir begins to fill. Once the second tank reached 190, a green light, and when it reached its maximum capacity (200), the loop stops.

  I have most of the finished project, but my problen with my program, this is when the first tank ends and begins the second tank, the second tank begins where the first tank ends (90). I want red light stay lit while the second tank is filled from 0 to 200. What is the best way to get around this problem? I use the case structures and a while loop.

  Objectives

  -Fill the first tank to 90, the red light turns on

  -Second reservoir begins to fill with 0, the green indicator lights to 190

  -End of loop when second tank reached 200

  What happens if you would subtract 90 wire goes to the second tank?

  Yet, you have to rearchitect your code like a machine in good condition with levels of reservoir in the shift registers. using the iteration count is relatively rigid.

• I have a business (with 10 cases) structure and I want 2 of them to be included in a loop.

  Hi all

  I'm new to this forum and I have a question.

  I have a business (with 10 cases) structure and I want 2 of them to include in a loop.
  How can it be done?

  Thank you.

  mosheg.

  Use own State Machine, where you can select the case according to your needs

• Reset a case structure

  I write a VI that reads a signal to a comparator and send
  output
  for a
  structure of the case.

  The ides behind the project is EMG (surveillance active/inactive muscle
  (times).

  The structure of the case is the following:
  If 1: Count up and if the account reaches 10 then green LED (muscle represents

  Active)

  If 0: Count up and if the account reaches 10 then red LED (muscle represents
  inactive
  "and must be exercised).

  My question is how can I reset the structure of the case again: that is to say, if

  Case = 0
  and the inactive period of time reached 10 and the RED LED lights, I want it to so
  tour
  off
  and set the counter to 0 if it passes in the box = 1.
  (The idea is that this RED LED is a vibrator (of which i engine
  will be
  output
  with the help of data acquisition). The engine lights, just like the RED LED to indicate to
  one
  user
  the muscle must be exercised, but I don't want the motor to be constant, I

  It takes
  to turn off when the muscle is exercised and then re-run the County)

  I have no probably explains this very well, but I am attaching my VI.

  Any help would be appreciated

  Take a look at the attached VI.  I recorded at LV8.0 because I didn't know what version you're using.

  Hope I got what you're looking for.

• How can I fix iphone and ipad to recognize my printer air.  I t o disconnect the printer and wait for 30 seconds before reconnected and then they both recognize the printer

  How can I fix 6s iphone and ipad air when they do not recognize my printer air.  After unplugging the printer for 30 seconds, they can connect to the printer

  Hey robertafromnull,

  Thank you for using communities Support from Apple. We can see from your post that you are having problems with printing of your devices on a printer of Air and that it would be happy to provide advice to solve this problem.

  Let's start by going to the section called "If you can not print on your AirPrint printer" in this link here: Topic AirPrint. This should contribute to help you get started with you back to printing from your iPhone / iPad. Let us know if this can help, or if you encounter any problems.

  Kind regards.

• The case structure and diagram disable abnormality of structure!

  
  

  I see the behavior it describes.  I went back to 8.0 and see this behavior.  The documentation that you linked to is a bit misleading in places and flat in others.  If you build your VI in an exe, it behaves as expected.  I think "compilation" in the links is back and forth between LabVIEW compile source code to run in LabVIEW and LabVIEW (building) of the compilation of the source code in an EXE file.

  In 8.0 structure dealing with a cable constant to it does not work in LabVIEW or EXE.  8.2 and later, he worked in an EXE file.  In all versions of 8.x, disable diagram structure will the VI memory in the EXE file.

  Thus, article area devloper is the confused and false in some places, as this only works when the VI is integrated into an EXE file.

• Someone knows the slow loading web pages with Microsoft 8.1 upgrade? Mine waiting for a minute or two and then load it, or expires and does not load.

  This problem did not exist with the original version of Microsoft 8 Pro that came with my Dell XPS new in February of this year. He has only started happening since I upgraded to 8.1 two days ago.

  You are using a pre-release version of the software.

  You can expect random inconsistencies and unexpected behavior.

  You should never install a beta prodcut on your hand, production of the computer

• get the structure of the event inside the while loop to wait for event occurs before the execution

  Hello

  I have a small problem, when I raise an event using a value change button, which works very well.  The problem is that the VI does not wait for me raise an event and instead runs the same event again, even if I have not pressed the button to start again.  The mechanical action of the button switch is released is.

  I was wondering how you get the structure of the event to wait for a user event, after that he executed the first time.

  James.Morris wrote:

  There is no reason that the event should be raised twice as much that the only way that it fires in your code is by the user by clicking on 'Hall measure only'.

  Oh yes, there is, and I deserve a kudo for this one.  Mechanical action on the button is set on the switch until published, so click to generate an event, on the bottom and on the square, attached is an example.

  My boy has my students hate this question, and to be honest, I hated it.  When never would you do that intentionally?  Honestly?  Anyway to change the button back to normal (as default latch when released) and move the terminal button in the structure of the event where it is managed and it will work as usual.

• Stuck "waiting for the printer to be available."

  After initially looking at it's going to print, the printer dialog box displays "waiting for printer to be available" and it's there (even if the printer - inkjet HP series C3800 - is ready).

  Here is what I tried:

  Using the HP utility software on the same computer, I am able to successfully print a test page, which rules out a problem with the printer and its connection to the computer.

  Printing worked normally before moving on to the Sierra. I tried resetting the printing system and add new printer (Sierra recognizes very well). I also tried to run in case disk utility have a permissions problem.

  I'm stumped at this point. Help much appreciated.

  Same story, but with a HP Laserjet P3005dn, specific scenario, the exact symptoms, exact attempts to improve...

• Cannot auto index from a for loop through a structure of business output

  I have a loop nested in a case structure, and outside the case, the structure is written to measure Vi. at each iteration of the loop for, I am trying to send data to writing custom Vi by using a tunnel with automatic indexing enabled. But writing custom Vi saw the release of the latest iteration of the loop. Is happening because I try automatic indexing on thanks to a structure of matter? How do you set up business structures to automatic alow to indexing?

  The loop passed out all the data in the form of a table (a row/iteration) 2D and add it to the file. However, your scalar indicator 'Output average SM' will not show the value of the last inner iteration. If you want to see all sequence values, move the indicator in the innermost loop.

  Also erase you the previous errors in each iteration, so you won't see any errors.

  As a general rule, you have far too much code duplication. For example, your inner loops share a huge amount of code. Everything that needs to be in the structure of case is code that is different. Here's how you could simplify it. (it of just a project and probably has errors).

  There are also 'model boom' that you can use to simplify things a lot more.

• Start stuck on "Please wait for the Local Session Manager."

  I would say that this problem started a couple of days. Went to start my laptop (Toshiba) and he sat on the "Please wait" message forever.

  Had no problems to start in safe mode. Looked up various ways of addressing the problem.

  Was able to change the resume date and back a few weeks ago. Still no luck. Happened to read something on a printer Epson being perhaps the problem driver (it was installed a day before the date of restoration chosen). Uninstalled the drivers, computer still does not start.

  Tried restarting running. I do not have the CD it came with Vista, but it was an option when you hold F8 during startup (I think?) Couldn't find any problems.

  Ran check on memory. No problem either.

  Changed settings for a verbose startup and ran a Diagnostic startup - all good for this. Then tried selective startup load system services... This is when the error occurs. When starting, it hangs on "Please wait for the Local Session Manager" and does nothing more.

  I looked in the event viewer to see what came that time and a couple mistakes were:

  Event ID 6000: winlogon notification subscriber was unavailable to handle a notification event.

  Event ID 7026: the next (s) start or start failed to load system
  spldr
  Wanarpv6

  It would be very useful for me not having to run my computer in safe mode automatically all the time, although it is useful that I at least have that option. Any help is greatly appreciated.

  Hello

  1. by chance your computer is connected to a domain environment?

  2. as you mentioned in your article that you tried the selective startup, I want to confirm if you have disabled the services left 3rd after hide Microsoft services?

  If you did not disable these services make sure you disable and then check if it works.
  See the article below for more information.
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: When the diagnosis is complete, don't forget to reset your computer to normal startup. Follow step 7 in the above article.

  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Problem with several sub-groups through case structure Enum: 'the VI isn't in a State compatible with this operation.

  Hello

  I'm using LabVIEW 8.0 and I'm trying to create a subgroup of experts which shows the façade of a subvi according to the choice made by the user via the menu drop down Enum.  I wired the Enum to a case structure and apply a coding identical to each structure of individual cases with the exception of course change the source of sub - vi.  However, you receive an error "The VI isn't in a State compatible with this operation."  I have managed to make a single sub - vi work within a subgroup of experts using a true/false case structure and the same exact coding.  However, now that I use an Enum box connected to a structure of the case, I get this error.  I enclose my diagram as well.  Could someone help me as to where it is that I am wrong?

  Thanks in advance!

  If your VI runs already, when you try to run it? Which returns the error you get.

  Check the State of VI before trying to run or make an error handling.

• Waiting for a transition to be completed?

  I use Tweener.AddTween () to apply some transitions to my sprites who say quarter of a second. Once the transition is complete, I need to do something else. The problem is the line immediately after the transition is executed immediately (it does not wait for the transition to complete) and all that mess up. Is it possible in a synchronous way expect the transition ends without taking CPU in a loop, etc.?

  Hey p3pp3r,

  There is a setting for the tweener Oregon 'onComplete' call that performs a function is completed. It goes right into the addTween method.

  Here are more details on the onComplete parameter (along with several other more useful):

  http://hosted.Zeh.com.br/Tweener/docs/en-us/parameters/index.html

  example:

  Tweener.addTween(myobj, {x: 45, onComplete: myFunction});
  

  hope that helps. Good luck!

• What is the cause of the message "Waiting for Service ' Console CVD activity

  I have two related questions.

  basis, I just started centralizing 200 computers ish, all except 2 appears fine, 2 questions, one below and another with VSS errors.  This message is just for the question "in waiting for the Service.

  1. What is the cause of the message "Waiting for Service ' Console CVD activity and is there anywhere that documents these meanings of status.
  2. No idea where I should start troubleshooting the message "Waiting for Service ' I get to the computer below.

  I have a computer with this status which comes to have installed the client and will not be to centralize.  Other computers seem to work properly (centralized).

  The computer is to ping requests, but appears as disconnected in the console.

  I deleted the CVD and restarted the centralization CVD using a different policy on a different volume without change.

  Journal of the history of CVD below

  Description of the Type of weather

  31/01/2014-08:52:32 AUDIT_EVENT assign device, device: PC30866 (1995), cardiovascular disease: 11614, political CVD: don't Default - every 4hrs - no drive D (1.1)

  02/05/2014-13:53:58 politics AUDIT_EVENT assign CVD, CVD: PC30866 (11614), CVD policy: Migration Post-quotidien (1.0)

  31/01/2014 General Office EVENT 20:44:46 service error

  31/01/2014 General Office service EVENT 17:39:04 error

  31/01/2014 14:44:34 EVENT has not finished downloading, internal error, exception attached

  31/01/2014 General error from the EVENT 13:05:15 service office

  31/01/2014-12:30:37 TRANSACTION_START PC30866 - centralize endpoint

  the transaction log has an inscription mentioning a failure (not sure if it is the server or PC related) disc.

  Diseases cardiovascular diseases cardiovascular name Type State layer size (MB) data transferred (MB) branch reflector savings start time end time transfer (MB)

  Of the endpoint PC30866 centralize 11614 reading disc failed 169648 1531 0 31/01/2014 12:30:37 05 d 04:16:52

  The next event is in the application event log and the Mirage event log for the failed computer. (there were not all other errors in the paper since the deployment of mirage customer and there is no errors in the system event log)

  Event type: error
  Event source: VMware Horizon Mirage customer
  Event category: no
  Event ID: 0
  Date: 31/01/2014
  Time: 20:44:46
  User: n/a
  Computer: PC30866
  Description:
  Error general service office
  Unexpected exception taken (sender Name:Wanova.Desktop.Service.exe
  There is no policy context.
  , the object exception System.OutOfMemoryException: Exception of type 'System.OutOfMemoryException' was thrown.
  System.Collections.Generic.List to ' 1.set_Capacity (Int32 value)
  System.Collections.Generic.List to ' 1.EnsureCapacity (Int32 min)
  to System.Collections.Generic.List' 1. Add (T item)
  at Wanova.Net.DataTransfer.TransferStreams.SignatureResponseStream.ProcessChunk (ChunkInfo chunkInfo)
  at Wanova.Net.DataTransfer.TransferStreams.ChunkInfoDecodingStream.BeginWrite (Byte [] buffer, TransferStreamWriteCallback onWriteComplete)
  at Wanova.Net.DataTransfer.DataHandler.ExecuteDataStreamTask (DataHandlerExecutionTask task, MarkCompletionCallback markCompletionCallback)
  at Wanova.Net.DataTransfer.DataHandler.ExecuteTask (IExecutionTask task, MarkCompletionCallback markCompletionCallback)
  Wanova.Net.DataTransfer.ExecutionController.QueueListener (Group IExecutionTask)
  to Wanova.Common.ThreadUtils.ParamaterizedWorkItem'1.Run (object fakeParam)
  at System.Threading.QueueUserWorkItemCallback.WaitCallback_Context (Object state)
  at System.Threading.ExecutionContext.Run (ExecutionContext executionContext, ContextCallback callback, Object state, Boolean ignoreSyncCtx)
  at System.Threading.QueueUserWorkItemCallback.System.Threading.IThreadPoolWorkItem.ExecuteWorkItem)
  at System.Threading.ThreadPoolWorkQueue.Dispatch)
  at System.Threading._ThreadPoolWaitCallback.PerformWaitCallback (), ends at True)

  For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  It turns out that this computer seems to have hard drive errors, so not a matter of mirage.

• VMware-vim-cmd: waiting for orders to be completed?

  Hi all, I adapt a backup script I made for VMware Server 1.x to VMware Server 2.x and I'm having trouble doing ordinary things like 'suspend' or "create a snapshot" "a VM from starting.

  There are several ways to do the same thing in a certain way does not require any authentication, others indeed require authentication, for example, to create a snapshot, you can:

  VMware-vim-cmd vmsvc/snapshot.create 'id of the virtual machine.

  or

  vmrun-h https://127.0.0.1:8333 / sdk u user-p password of snapshot "[datastore] /vm_path/vmx_name.vmx '

  The problem with vmware-vim-cmd approach is that it does not wait for the command to complete, and is not a welcome feature in a script.

  Instead, the vmrun command wait until the end, but to use it in a script, you must also include the identification of the user and password information in the script, and it is not welcome.

  So the question (as shown in the topic) is: is it possible to make orders of vim-vmware-cmd to wait until the end?

  If someone knows how to do that I would be very grateful

  Thank you for reading,

  10nico

  The vimsh and the vimsh wrapper vmware-vim-cmd is not officially supported by VMware, that being said, I agree that it should allow you to check the situation, etc. It can be a pro/con and depending on how the call command, the wrappers actually communicate to the VI API server, and if you look at the VI API there are all both blocking and non call.

  Vmware-vim-cmd, the command is executed and returns to the shell for most. You might be able to monitor the tasks that is created and ensure that it is completed, but I have not played too much with it.

  [root@himalaya scripts]# vmware-vim-cmd vimsvc
  Commands available under vimsvc/:
  auth/             login             task_cancel       task_list
  connect           logout            task_description
  license           property_dump     task_info
  

  Again, these are undocumented, unsupported and the behavior will vary =)

  I advise to use the VI API (Powershell or VI Perl Toolkit) to accomplish your tasks, and you can even take a look at some of the utilities that are available with the VI Perl Toolkit Utilities: http://www.vmware.com/support/developer/viperltoolkit/viperl15/doc/perl_toolkit_utilities_idx.html

  =========================================================================

  William Lam

  VMware vExpert 2009

  Scripts for VMware ESX/ESXi and resources at: http://engineering.ucsb.edu/~duonglt/vmware/

  repository scripts vGhetto

  http://Twitter.com/lamw

  If you find this information useful, please give points to "correct" or "useful".