Waiting for tray 2 to lift? (color laserjet 5500 dtn)

Printer displays the message "waiting for tray 2 to lift", also said that it is to treat the work but nothing is printing. Help please!

The trays are lifted audiences on these, you might be able to go back, look at the back of the status bar (with a blowtorch), see if the tray is thrown.

If this isn't the case, then check that the tray is not damaged, if it is OK, then you can change the paper pickup unit.

The drive to lift for tray 2 is there.

This is for the RG5-6670-110CN 5500.

You can remove it but to replace the whole unit is only 2 screws and it comes out of the box the cartridge before, so it's a quick repair, not requiring no not a high-level engineer.

Tags: HP Printers

Similar Questions

  • Color LaserJet 5500: error code 59.5 k

    Hello.
    My Color LaserJet 5500 poster printer error code 59.5 k while a flashing orange light.

    What can I do to solve the problem?

    Thank you

    59.5 K refers to a motor with the toner cartridge problem black.  Several times it might just be a bad toner, that does not illuminate.  You can test.  Remove all tonics of the printer.  Turn on the printer and when it asks you to install toner, press the menu key and scroll to the diagnostics menu and then choose the item to disable control of the cartridge.  The printer will say check and he would come after a while to say ready, diagnostics mode.  If it does not try once more with the menu in the same way.  When it indicates ready diagnosis mode, open the door and install the toner cyan in black housing and the other two colors in their regular time slots and let the black toner in the printer.  Now close the door and the printer should say check and eventually come to loan, diagnostic mode.  If she comes back with the error, then you have a hardware problem with the train of drum for the black slot and will need service.  If it's ready, print a configuration page in the menu information and it should send a cyan color config page.  If so, your problem is most likely a bad black toner and it must be replaced.

  • Unable to connect to my 'new' dn Color Laserjet 5500

    I tried the simplest of methods, an ethernet cable into the printer and the desktop, but not joy.

    Its a 5500dn "renovated", way to much for an office at home, but at a price advantageous and all, I want to do is printed.  Is there something that I am missing?

    He finally cracked with a value of £30 to help of the boys at the Black Box in Lancaster.  Using two plug PowerLines and sort of dynamic/static IP addresses, I can now print on my printer cheap and very heavy.  Thanks for the tips.

  • Unable to print on Windows 8 with Color Laserjet 1600

    I installed DOT4x64.msi on my new laptop HP Windows 8, since this seems to be the only average current to connect my Color Laserjet 1600. The printer will now appear in the section "Devices and Printers" Control Panel.  But when I try to print something, I get an error message that says that I can't print to the printer. I spent nearly an hour on the phone with HP support with no resolution - in fact, after all this time, I was told "this Department does not support this printer!.» Any ideas on a solution here? Thank you!

    PS - I initially posted on a different picture, I hope someone here can help.

    For this device, the driver of windows 8 will not release until the end of January. Please bookmark this site and refer to it for more information up-to-date.

    Can I 8 supported for LaserJet printers

    In the meantime, drivers windows 7 should work for this device.

    Color Laserjet 1600

  • HP Laserjet 5500: failure of multiple copies

    I am not able to print multiple copies, as I can't find the mopier mode must be disabled in the properties

    The exposed attributes will probably depend on the driver that you have installed.

    My Windows Professional 10 64-bit system has several built-in drivers (for PCL 5, PCL 6, Class PCL6, PS, PS class) for the Color LaserJet 5500 printer:

    You may need to click the Windows Update button in the Add Printer dialog, then wait (possibly several minutes) while additional drivers are downloaded, until the list is filled again.

    Some time ago, I downloaded the drivers PCL 6 and PCL6 class for this printer run tests (I don't have this model of the printer, if the target port is defined on file:).

    With the pilot PCL6 class , shows the device settings tab in the printer properties dialog:

    With the PCL 6 driver, the device settings tab on the printer properties dialogue indicates:

  • Tray 3 paper jam 13.20.00 for HP Color LaserJet 4700dtn

    We have a

    HP Color LaserJet 4700dtn

    which gives the message paper jam in tray 3 13.20.00

    I watch a video on a similar printer and photos on the model 4730

    but I can't seem to locate a paper sensor/banner (if it exists)

    for this particular model.

    Suggestions?

    There are three trays on this unit.

    We decided to remove the offending set and that is the problem solved

    It said users, since they have many other printers to use, that works of this unit, but with two trays.

    As it is a color model and now it works, they were happy.

    We have the tray offending in our office and we will watch more closely if something seems suspicious, but for now, the device works

  • HP Color LaserJet MFP M277 Pro: No software or drivers are available for HP Color LaserJet Pro M277dw MFP

    Trying to download the latest drivers (I couldn't scan with Easy Scan more after the release of macOS sierra 10.12) I received the following massage

    http://support.HP.com/us-en/drivers/selfservice/HP-Color-LaserJet-Pro-MFP-m277-series/7089945/model/...

    No software or drivers are available for this product with the selected operating system. Please make a different selection, or visit the product home page.

    PS: My OS has been identified correctly in the web page.

    Hi @pisca46,

    Thank you for joining the HP Forums!

    I understand that there is no drivers for your HP Color LaserJet Pro MFP M277dw on Mac OS X 10.12 Sierra. I am pleased to see that for you!

    You are right that there are currently no drivers available at this time. In the meantime, I suggest trying the rest of this guide, of install a printer Mac driver by using Apple Software Updateand then try using the Apple Image Capture.

    Otherwise, all we can do is wait for the drivers and software provision, or plan to use an older version of Mac OS X.

    If it helps, please consider clicking on "accept as a solution." And, please click the thumbs up icon. The two icons are below this post.

    I hope this helps!

  • HP CL stream M880 MFP: HP Color LaserJet Enterprise flow MFP ME output tray

    We have a HP Color LaserJet Enterprise flow MFP M880 with finishing tray.

    With the finishing tray attached it only allows the output to the upper and lower trays on the Finisher and removes the exit option on the top shelf on the main part of the unit.

    Is there a way to get around this?

    We would like to have the option for all 3.

    In fact just the finisher installed a few days ago and after he's looking for there is no way to use the bar to original condition with the attached finisher.

    You remove the tray of origin during the installation of the Finisher and install the transfer unit in its place.

    Paper is then powered off the machine and in the transfer unit when it is moved to the right in the finisher.

    If my post is solved your problem and click the accepted as button solution under him.

    In order to thank a Tech for a post click the thumbs up button under the post.

    You can even click on the two keys...

  • Power failure during the update of firmware for Color LaserJet 2600n

    Just in the middle of the update the firmware for my Color LaserJet 2600n, the power is out. Now I can't get anything to happen on the printer. The screen, or the power lights and the error light, but it does not work when the power is put on. I think that he wiped the previous firmware and either had not started or has been along the way in writing the new info. Is it possible that I can cancel it and reload the original firmware? It hangs on my MacBook Pro running OS 10.6.8. The only thing that the instructions seriously cautioned against a interrupt the installation. Needless to say, this is exactly what happened when the power is out. Any help would be greatly appreciated.

    Randy

    Able to understand me. Has proved to be quite simple. Powered off the printer and turn it back on and represented the firmware upgrade program. The printer didn't restart automatically, so I had to power off and wait 5 seconds before feeding this back. Once he recalibrated itself (which takes several minutes), I was in business.

  • installed slow start with driver for HP Color LaserJet CM2320nf MFP

    I have Windows 7 pro 64-bit installed. After that I installed the latest driver for HP Color LaserJet CM2320nf MFP, my network is not initialize 2 to 5 minuets and the PC won't start any programs until it does. The printer works very well after starting my network it's just frustrating to have to wait this long. I have the printer plugged into my Intellinet router and the printer set to DHCP for IP setting. I asked HP about this problem and they can't help me because it is a software problem and not hardware related

    Edit: I have a program of snooper network called Netscan indicates the printer working group is "WORKGROUP" and my working group is "MSHOME". This would cause problems? I can't find a way to change the workgroup printers.

    Jim

    Hello
     
    Perform the check and the boot if the problem persists.
     

    To help resolve the error and other messages, you can start Windows XP, Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

    Note: perform step 7 to reset the computer to start as usual after the boot process.

    How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

    Hope that helps.

  • Impossible to activate the services web ePrint for Color LaserJet M551

    Hello

    I read all the posts in this forum about the web services enabling ePrint to the question and tried all suggestions with no luck.

    Here's the situation:

    1. The printer works fine on place. I can print without problem.
    2. The printer is connected.
    3. All my router ports are open for outbound connections, including UDP.
    4. Communication using log in my router I can see that the printer can resolve DNS names using either my ISP DNS server or the suggested 8.8.8.8 and 8.8.4.4. Using nslookup shows ' registration-pro - site1print.houston.hp.com "Decides to 15.240.60.111 and" registration-pro - site2print.houston.hp.com "Decides to 15.201.224.79.
      This indicates that the printer can indeed resolve the addresses. Newspapers also Awakenings that the printer communicates with the servers (connection is established and data transferred) via https (probably the web service), but always after a few minutes the clearance process is to expire.
    5. I tried this allowing the procedure since a few days my believe that the recording servers should have worked some time during this period.
    6. I'm frustrated
    7. .. .even more frustrated
    8. what I am doing wrong?
    9. Help, please!

    trying to install eprint for my new M551dn Color LaserJet and it fails with the

    Who out there having the same problem I had. HP could not help me I restore to factory settings and reconfigured everything and all of a sudden the printer managed to enable web services and print the print code.

    Good luck to you face the same problem!

    / MrQQ

  • color laserjet pro m252dw: How do to return/difficulty recent update of firmware for hp color laserjet pro m252dw as now does not

    My printer color laserjet (color laserjet pro m252dw) no longer works due to not recognize a black cartridge to third because of a recent update of the firmware. Error given is 'Supply memory error'.

    I already looked to the top of the page of Software Support for this printer, but new and recent firmware update is not released/listed, only the firmware upgrade market is given.

    I'd appreciate advice and instructions on how to return/repair my printer no longer print.

    Can you please advise on which firmware update to install instead to get my printer back in the order of operation?

    Thank you very much

    Geertje

    PS: HP: how VERY boring; next time that I'm in the market for a printer I have will conduct the review of my options

    According to the other thread that I have commented on the user managed to solve the problem of roll back firmware version 20160331 to 20150716 .  Unfortunetly the user did not comment if the old version of firmware is out so that we can share a simlilar solution.  It may be that this person had a copy archived in offline mode or found another source outside the HP support Web site.

    At least you can get an older version of firmware all the steps that we share for the firmware downgrade won't do you no good.  I'd be careful to search a German site for firmware updates.  HP has put regional locks in place according to international contracts, that they do to market their products in a given region.  Using a German firmware on a printer WE made may have strange side effects on what types of cartridges are allowed.

    What is perhaps a better use of your time would be to contact your 3rd party cartridge company and see if they can send you a cartridge that is compatible with the new firmware.  Chances are that they have seen the same problem with other users and already have a chipset to work around the problem.  In this way, you can stay on the newest firmware and continue to use your favorite too cartridges.

  • Driver for HP Color LaserJet MFP Pro M PCL 6

    64-bit driver for HP Color LaserJet Pro MFP M477 PCL 6: I have one of these printers, which is able to print double-sided automatically.  The new driver (64-bit) will not accept when I switched to a new laptop, manual duplex printing.  Does anyone else have this problem?  I updated the driver, but the problem persists.

    I managed to find the solution... it is a lot harder than I imagined composed I don't remember clearly how I found it.  But I think it's what you do... Use the control panel to get to the devices and printers, right-click for properties of the printer, then select device settings, then select installed in the duplex unit.  Yes... complicated.  How the average dumb guy like me never to solve such a problem?

  • Color LaserJet Ent M553dn: HP Laserjet Enterprise M553dn PCL6 x 64 drivers for Windows Server 2003

    Just bought a HP Laserjet Enterprise M553dn and was able to install the drivers for Windows Server 2003 x 86 driver disc supplied with the printer, but I cannot locate the drivers for Windows Server 2003 x 64.

    I checked the site hp.com, but what they have there is PCL5 x 64 drivers, which gives me a 'printer driver is not installed. Message operation could not be completed.

    Just for fun, I tried to download the drivers for PCL6 Windows 7 x 64, and trying to set up the printer with these, but it gives me a message "Windows is unable to locate a suitable printer driver.

    Where can I find the Windows Server 2003 PCL6 drivers x 64?

    Thank you!

    As any pcl6 driver will work, why not just load any pcl6 64-bit driver that is built into the operating system.  Simply choose hp on the left and choose any color laserjet 64-bit driver on the right.  If none is available, download the driver 64 bit hp universal pcl6.  When loading the driver do not have system autodect the printer but load the driver manually.

  • Color Laserjet M252N: HP Color Laserjet Pro printer M252N for Windows XP Embedded Standard.

    I can't install the driver HP Color Laserjet Pro printer M252N to my machine (OS: Win XP Embedded Std version) without an internet connection.

    1 error message are requested in advance for MS .net framework 3.5. (after that, I download and installed: NETCFSetupv35.msi)

    I found the name of the printer in the list of drivers, but then I try to add a new printer with this driver, the pop-up error message and the installation is not complete.

    My question is: the HP Color Laserjet Pro printer M252N are not compatible with Win XP Embedded Std?

    Please help, even the HP sales technician unable to answer me to this questation.

    Hello

    The HP Color Laserjet Pro M252N Featuer software complete is not supported on Windows XP, however you can get the features of the printer using HP PCL 6 Universal Print Driver listed on page 9 of the User Guide, be aware that the Service Pack 3 must be installed on the operating system to use the printer:

    Make a right click my computer and select Properties - locate Service Pack 3 in this form... If Service Pack 3 is not the operating system MUST be updated first:

    http://h10032.www1.HP.com/CTG/manual/c04475955

    You can download the HP Universal Print Driver below:

    http://ftp.HP.com/pub/softlib/software13/COL39348/LJ-95977-14/UPD-PCL6-x32-6.2.1.20636.exe

    As Windows Embedded edition is an edition of the customized version no official support is guaranteed.

    It is a customized operating system version includes only the components of the operating system selected for specific needs.

    Those selected by the OEM computer and not necessarily include any component required by the HP software or hardware.

    Try to install the printer and see if this can work, however it can work as explained and may not only the manufacturer of the computer can respond if such material can be installed on the operating system or not...

    Kind regards

    Shlomi

Maybe you are looking for