WAN port mini error 31

Similar Questions

• Cable modem has no WAN port

  I have XFinity for my cable and internet services.  We just moved into a house built in 1850 and due to the size of the House and horse hair plaster, upstairs gets very little signal WiFi.  I want to extend the reach of WiFi and intended to do with a couple of Airport extreme.  The only problem is, every tutorial I watch shows the first Airport Extreme being plugged into the WAN port on the modem cable suppliers.  My router/modem, made by Cisco, has no port Ethernet WAN port only 4.  Can I connect the Airport Extreme on port 1 and then put in place using the Airport according to normal or need a WAN port?

  If you have a modem/router, then you would connect an Ethernet cable from one of the four ports Ethernet LAN <>-... choose any you want, they are all the same... to the "O" on the AirPort Extreme WAN port.

  Then use Configuration utility of Apple AirPort "Wizard" to configure AirPort Extreme to create a wireless network that uses the same exact wireless network and the same password that the wireless Cisco uses.

  The wizard will apply automatically other correct parameters... Mode Bridge, by example... so you don't have to worry about things like that.

• What port mini display of brand to HDMI cable should I use?

  What port mini display of brand to HDMI cable should I use?

  Besides Apple, Belkin seems to have good reviews.

  Ciao.

• The WAN Port is communicating with the Ethernet switch?

  I have a Comcast gateway that the router is disabled in so it acts only as a modem. This is related to an Airport Extreme, which serves as my router via the WAN on the AE port. I created a different WAP with a Capsule temporal from the airport, located downstairs with an Ethernet cable from one of the Ethernet ports on the AE to the WAN on the TC port. I think it's what we call a 'roaming network.

  My question is, can I connect my switch Gigabit 8 ports in one of the Ethernet ports on the TC to complete connections wired to all devices connected on it, or should I first connect EI to the switch 8 ports and then connect the switch to the port WAN TC to complete my network "roaming"? In other words, plug it into the port WAN AE or TC still allows you to use other Ethernet ports as a switch?

  Thank you!

  can I plug my Gigabit 8 ports switch in one of the ports Ethernet on the TC to complete wired connections to all devices connected on it

  Yes, assuming that the TC has been configured to run in Bridge Mode, which would be normal.

  or should I first connect EI to the switch 8 ports and then connect the switch to the TC WAN port to complete my network "roaming"?

  It would be considered preferable to wiring, if it is convenient to do so.  For example, in the configuration of the wiring in the previous example just above... If there is a problem with the time Capsule, then all devices connected to the switch to the time Capsule would have a problem as well.

  If the switch is connected to the AirPort Extreme, and the TC is then connected to the switch... If the TC has a problem, the other devices connected to the switch of will not be affected.

• LAN/WAN ports not supposed to be Gigabit? Capped at 250Mbps, NOT because of the ISP LAN devices.

  Hi all

  Have a bit of a problem here. I have Internet Fiber-to-the-home (FTTH) with Bell Canada and have their Fibe Gigabit service which is 940/120 speeds up and down, respectively. I was able to bypass his combo modem/router using a switch connected to the optical network terminal (HAVE) where the fiber cable enters the House (which serves mainly my base modem) and using custom settings of VLAN and DNS in ports specific for my fiber IPTV service Bell and receivers work together through my router.

  So, I have a few routers that I tried this with to try to solve my problem. My Asus RT-AC5300 and others have no problem with having me my subscribed speed - certainly through devices connected to gigabit LAN and also via WiFi on compatible devices. But I'm not concerned about WiFi - it is specifically wired ethernet devices that are the cause. I use CAT5e and CAT6 cables only because he is a Gigabit connection. The issue I have with my Time Capsule (3 to, latest model AC) is that, literally, speeds for gigabit wired devices will not exceed 250Mbps downstream. Download speeds can hit 125Mbps without problem. Why is this? Is there something my Time Capsule prevents leave the LAN ports operating at gigabit full transfer speed? It is not only a device - I have multiple gigabit devices I tested, on all three of the TC ports, and none of them exceed 250Mbps. Yet when I connect them to another router gigabit, such as the Asus I've described but also others, they have no problem hitting 900 + Mbps downstream on the exact same network configuration and Setup at home.

  Thanks for any ideas, comments or suggestions. Y at - it a setting I have accidentally enabled that is the cause? I had much rather use the TC of the most convenient airport for my network I was planning on getting multiple Airport extreme to position around the House to cover literally home WiFi and LAN bridges through the simple installation of these devices, but I do if I can't use my fiber subscribed speed.

  OR maybe I have a defective unit. Thanks again for the help!

  See you soon

  The issue I have with my Time Capsule (3 to, latest model AC) is that, literally, speeds for gigabit wired devices will not exceed 250Mbps downstream. Download speeds can hit 125Mbps without problem. Why is this?

  Apple AirPort routers have been designed to work with the cable standard and DSL connections.  The fiber is the new ball game, and Apple knows yet how to play the game, let alone to understand the rules.

  Most of the problems associated with connections to high speed on airports is a result of the decision of Apple to eliminate any kind of manual settings to manually adjust the speed of the WAN port on the router... and are based rather on an "Auto" setting.  Automatic adjustment seems to work pretty well on the fiber up to approximately 100 Mbps connections, but the WAN port is struggling to negotiate with high-speed connections when it is connected directly to the fiber. LAN ports can also be affected.

  Some users have reported that insert a Gigabit switch between the connection of the fiber and the Time Capsule or AirPort Extreme has helped with speeds. The theory here is that the switch can negotiate with the fiber connection much better than the WAN port on the Apple device.  If you have a handy Gigabit Ethernet switch, that it could not hurt to try this "Workaround".  Other users report no benefit when they try it.

  Yet when I connect them to another router gigabit, such as the Asus I've described but also others, they have no problem hitting 900 + Mbps downstream on the exact same network configuration and Setup at home.

  The time Capsule is not directly connected to the fiber connection, so it OK to talk and negotiate with what he sees as a 'normal' a conventional router connection.

  Don't forget also that the 802.11ac products were designed before 2013. Current products have not changed since their introduction in June 2013.

  The bottom line... Apple needs to decide whether it wants to be an actor, or leave the routing other players company established. Such what, Apple is far behind the curve... my opinion.

  While it might not hurt to take the time Capsule to an Apple Store to check over the machine, you might want to ensure that they have in fact a fiber connection high speed to test.

• R7000 WAN Port does not use LAN as a substitute?

  I have a problem with my R7000. The WAN port is dead. I used it in access point mode for some time connected to one of my LAN ports, but I need to go back to a main router. Is it possible to run it in router mode outside of a LAN port, or I'm out of options and need to replace the router? Past the WAN port, everything works fine. Thank you!

  Ive never used Merlin, but I think you need to activate the dual WAN mode and just use the secondary interface for your main WAN while leaving the other disconnected.

• LRT224 - Dual WAN port forwarding

  Can you move forward say port 80 1 Wan IP and port 80 from WAN 2 to a different IP address. ?

  Also can you somehow choose TCP & UDP rather large only one or the other?

  I just replaced 2 routers with LRT 214 and LRT 224 TPLink its all works well. Except port forwarding

  With LRT224, a port forwarding rule is applied to the two WAN ports and two rules are necessary if you want to ship to TCP and UDP to the same internal IP address.

• WRT350n - what is the speed of the WAN port?

  Hello

  Virginmedia in the United Kingdom have 50 MB download capability now that I am interested in buying. I was advised to check that my current router (wrt350n V2 firmware v2.00.18) is able to handle this speed on its WAN port before you sign up. It is not clear on the data sheet if the WAN port is gigabut able ehternet, as well as the 4 ethernet ports, and I wanted to ask you just to be absolutely sure.

  Any help or clarification gratefully received.

  Snert

  As the router that you have its a gigabyte wireless router bits, and all the LAN port at the back of the router are the Giga bit Ports LAN. Your router will work with the speed of 50 MB, and you should be able to go online from all your computers.

• RV042 Dual WAN Port DMZ not acquire an IP from ISP

  Hello

  I am trying to replace my router with the more robust RV042 of current load balancing. Installation seems simple enough. However, I am having an issue gets an IP address of the DMZ port in load balancing mode.

  The two WAN is the same ISP and is both DSL, using the same models of DSL Modem. #1 WAN port works perfectly.

  Indeed, when an independent piece of equipment is installed in the #2 DSL modem, this gives an IP address instantly...

  The two DSL lines only require a MAC address to get their IP addresses, and none of the static values are allowed, perhaps to test only.

  The issue of intellectual property has been seen before. I can't find any reference to the iton this site.

  Thank you

  Steve

  Glad to hear that it works.

  The "save the settings and restart" is not all that rare, although it is not typical for your model.

  The obligation of power off is certainly not normal. He told me that some sort of electric lock has occurred. This could be a unique thing, caused by a discharge of static electricity, or it could indicate a manufacturing defect. If this is the first case he did re - is probably. If it is the latter, then it will need a trade at any given time.

  In any case, it seems that the MAC address index has been at least partially useful.

  Good luck, somone will be here if you need assistance once again.

• IPsec site2sitevpn and DMVPN on a single WAN port

  Hi Experts,

  can you please it is possible to use IPsec site2sitevpn and DMVPN on WAN port unique until I apply the two vpn on a single wan link connection please give your comments it's ok or not.

  Thanks in advance,

  ciscolearner

  Hello

  Yes you can, there is no conflict. I just tested and confirmed in a laboratory.

  Kind regards

  Tim

  Please don't forget to rate helpful messages and mark the answers accurate.

• RV180 getting is not gigabit/1000 WAN port speed

  I have my RV180 connected to a modem Motorola SB6121 cable into the WAN port. The modem indicates that the connection to the router is only 10/100. If I plug my laptop directly into the cable modem, it indicates that the connection is full gigabit.

  RV180 configuration, less Networking > port management, the WAN (Internet) port is enabled and Full Duplex value and speed of 1000. Auto-negotiation and flow control are unchecked. I also changed the WAN port for auto-negotiation and restarted the RV180. But none of these settings seem to affect the speed detected on the modem end. He always shows a light orange Link that says 10/100Base-T, instead of a blue light of the link indicating full 1000Base-T.

  Am I missing another setting somewhere, or is there another reason why the modem insists that the connection to the router is only 10/100?

  If I plugged my laptop into the RV180 rouoter's WAN port, I do not see how that would be a proper test.
  

  Then two different cables do you use?  The reason why I ask because there are some cables Cat5/Cat6 "shonky" that are not properly completed.  If they are properly finished cables, you can obtain 1 Gbps.  If this isn't the case, you will get 100 Mbps.

• RV042G difference between the Strip protocol binding bandwidth <>- for the WAN ports

  Can someone explain a little better then the manual what are the differences between the management of bandwidth on the WAN ports and protocol bindings?

  If you specify in each section which protocol should go where, why have two places to set this up?

  Or are there things to remember when you use one of them?

  Protocol binding affects the leaves of outgoing traffic how a particular WAN interface.

  With bandwidth management, you specify bandwidth across WAN, a service must be used.

• [SRP527w] Use the 4 Ethernet Port as a WAN Port?

  English:

  Hello world

  I just can't understand how to use the ethernet port 4 as a WAN port.

  I think it's possible because it labeled LAN/WAN at the rear of the unit... If someone can, please let me know how!

  Thank you for your help,

  Gaultier.

  English:

  Hi all

  I can't configure the 4 en world WAN ethernet port.

  It seems to me that this is possible since the port is called LAN/WAN on the device... If someone did it, thanks for that comment!

  Thank you for your help,

  Gaultier.

  Hi Gauliter,

  Please use the Administration > menu of switch setting.  Set the option Interface DSL for disable use 4 Port LAN instead of the ADSL interface.

  Note, this setting will factory reset the router and completely disable this ADSL interface.

  

  I hope this helps.

  Andy

• port mini-PCIe for WAN on other X120e uses

  Hi, I ordered as a X120e without the conectivity WAN option so he came without the card, but I have this mini-PCIe available, is it possible to use this port for something else? I wanted to put a second wifi card for the tests of penetration and research... or even a solid storage card in there.

  Well, unless hack you the BIOS to the white list what wireless card you install, it will be a moot point. In addition, you must find an ssd pcie with an integrated controller which presents itself as a drive controller, of which none of those available, I know of no. So, in conclusion, unless an engineer comes out and says he can endure more, chances are that we cannot use it for anything apart from Lenovo wireless cards.

• the lack of mini WAN port (atw) No. 4

  HP printer all-in-one 6310

  Windows 7 64 bit

  When I try to print the prinyter prints a line and not more?

  You can download the full features and software drivers from the Web site.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-76831-1&cc=us&DLC=en&LC=en&OS=4063&product=1119598&sw_lang=