WAN with 3 routers RV320 and client VPN routing

Similar Questions

• Client VPN router IOS, and site to site vpn

  Hello

  Im trying to configure a vpn client access to an ios router that already has a vpn site-to site running. I don't see how the two can run on the same router.

  So I guess my question is is it possible? and if anyone has therefore had a config that they can share or a useful link.

  IM using a router 800 series with 12.4 ios

  Thank you very much

  Colin

  ReadersUK wrote:
  Hi
  Im trying to configure access for a vpn client to a ios router that already has a site to site vpn running. I cant see how both can be running on the same router.
  So i guess my question is can this be done? and if so has anyone got a config they can share or a useful link.
  im using a 800 series router with 12.4 ios
  Many thanks
  Colin
  

  Colin

  It can be done. Look at this config example that shows a router configured with a site to site VPN and client vpn - connection

  https://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080094685.shtml

  Jon

• PIX - PIX VPN and Client VPN - cannot access core network

  I hub and spoke PIX and a VPN Client that connects to speak it PIX, much the same as the example configuration here: -.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00800948b8.shtml

  This example shows the client VPN access to the network behind PIX RADIUS. I want the client to also be able to access the central network, i.e. the client connects to the pix speaks via vpn, and traffic is routed through the vpn to PIX - PIX to the central site.

  How this would change the configuration contained in the example?

  See you soon,.

  Jon

  You can not do this, the PIX cannot route a package back on the same interface, it is entered in the. The only way to do that is to have the client connect to the hub PIX, but then they would not be able to get to the network behind PIX distance either.

  Or that the customer would connect on a different interface in the PIX of distance, but this would mean another connection ISP on this PIX. Example of config is here: http://www.cisco.com/warp/public/110/client-pixhub.html

• Client VPN router IOS does not connect

  Hi all

  I'm having some trouble of Client VPN connection over the internet to our Cisco IOS router. Some help would be very appreciated!

  On the VPN client log I get the following error messages:

  ---------------------------

  ...

  573 16:32:13.164 21/12/05 Sev = WARNING/2 IKE/0xE3000099

  Size invalid SPI (PayloadNotify:116)

  574 16:32:13.164 21/12/05 Sev = Info/4 IKE/0xE30000A4

  Invalid payload: said length of payload, 568, not enough Notification:(PayloadList:149)

  575 16:32:13.164 21/12/05 Sev = WARNING/3 IKE/0xA3000058

  Received incorrect message or negotiation is no longer active (message id: 0x00000000)

  ---------------------------

  We get debugging on the router that I'm trying to connect:

  ---------------------------

  router #debug isakmp crypto

  ...

  21 Dec 16:32:16.089 AEDT: ISAKMP (0:0): received 203.153.196.1 packet dport 500 sport 500 SA NEW Global (N)

  21 Dec 16:32:16.089 AEDT: ISAKMP: created a struct peer 203.153.196.1, peer port 500

  21 Dec 16:32:16.089 AEDT: ISAKMP: new created position = 0x678939E0 peer_handle = 0 x 80000031

  21 Dec 16:32:16.089 AEDT: ISAKMP: lock struct 0x678939E0, refcount IKE peer 1 for crypto_isakmp_process_block

  21 Dec 16:32:16.089 AEDT: ISAKMP: 500 local port, remote port 500

  21 Dec 16:32:16.089 AEDT: insert his with his 67B0AB34 = success

  21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): treatment ITS payload. Message ID = 0

  21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): payload ID for treatment. Message ID = 0

  21 Dec 16:32:16.089 AEDT: ISAKMP (0:0): payload ID

  next payload: 13

  type: 11

  ID of the Group: eggs

  Protocol: 17

  Port: 500

  Length: 12

  21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): peer games * no * profiles

  21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): load useful vendor id of treatment

  21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): supplier code seems the unit/DPD but major incompatibility of 215

  21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): provider ID is XAUTH

  21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): load useful vendor id of treatment

  21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): provider ID is DPD

  21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): load useful vendor id of treatment

  21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): supplier code seems the unit/DPD but major incompatibility of 194

  21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): load useful vendor id of treatment

  21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): supplier code seems the unit/DPD but major incompatibility of 123

  21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): provider ID is NAT - T v2

  21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): load useful vendor id of treatment

  21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): provider ID is the unit

  21 Dec 16:32:16.089 AEDT: ISAKMP: analysis of the profiles for xauth...

  .....

  21 Dec 16:32:16.093 AEDT: ISAKMP: (0:0:N / A:0): atts are not acceptable. Next payload is 3

  21 Dec 16:32:16.093 AEDT: ISAKMP: (0:0:N / A:0): audit ISAKMP transform 12 against the policy of priority 3

  21 Dec 16:32:16.093 AEDT: ISAKMP: 3DES-CBC encryption

  21 Dec 16:32:16.093 AEDT: ISAKMP: MD5 hash

  21 Dec 16:32:16.093 AEDT: ISAKMP: group by default 2

  21 Dec 16:32:16.093 AEDT: ISAKMP: pre-shared key auth

  21 Dec 16:32:16.093 AEDT: ISAKMP: type of life in seconds

  21 Dec 16:32:16.093 AEDT: ISAKMP: life (IPV) 0x0 0 x 20 0xC4 0x9B

  21 Dec 16:32:16.093 AEDT: ISAKMP: (0:0:N / A:0): pre-shared authentication offered but does not match policy.

  21 Dec 16:32:16.093 AEDT: ISAKMP: (0:0:N / A:0): atts are not acceptable. Next payload is 3

  ---------------------------

  You can apply the encryption the WAN interface card and check?

• Client VPN routing issue

  I am trying to configure client vpn software ver 5.0 for remote to connect to the local network behind a 1801 users.

  I can get the client saying its connected but traffic is not circulate outside in:

  When I try to ping an address 192.168.2.x behind the 1801 I get a response from the public ip address but then when I try to ping to another address I have no answer.

  I guess the question is associated with NAT.

  Here is my config, your help is apprecited

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  encryption password service

  !

  host name C#.

  !

  boot-start-marker

  boot-end-marker

  !

  enable password 7 #.

  !

  AAA new-model

  !

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  !

  AAA - the id of the joint session

  !

  IP cef

  !

  IP domain name # .local

  property intellectual auth-proxy max-nodata-& 3

  property intellectual admission max-nodata-& 3

  !

  Authenticated MultiLink bundle-name Panel

  !

  username password admin privilege 15 7 #.

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  ISAKMP crypto client configuration group 1801Client

  key ##############

  DNS 192.168.2.251

  win 192.168.2.251

  field # .local

  pool VpnPool

  ACL 121

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap throwing crypto

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  Archives

  The config log

  hidekeys

  !

  property intellectual ssh time 60

  property intellectual ssh authentication-2 retries

  !

  interface FastEthernet0

  address IP 87. #. #. # 255.255.255.252

  IP access-group 113 to

  NAT outside IP

  IP virtual-reassembly

  automatic duplex

  automatic speed

  clientmap card crypto

  !

  interface BRI0

  no ip address

  encapsulation hdlc

  Shutdown

  !

  interface FastEthernet1

  interface FastEthernet8

  !

  ATM0 interface

  no ip address

  Shutdown

  No atm ilmi-keepalive

  DSL-automatic operation mode

  !

  interface Vlan1

  IP 192.168.2.245 255.255.255.0

  IP nat inside

  IP virtual-reassembly

  !

  IP pool local VpnPool 192.168.3.200 192.168.3.210

  no ip forward-Protocol nd

  IP route 0.0.0.0 0.0.0.0 87. #. #. #

  !

  !

  no ip address of the http server

  no ip http secure server

  the IP nat inside source 1 interface FastEthernet0 overload list

  IP nat inside source static tcp 192.168.2.251 25 87. #. #. # 25 expandable

  Several similar to the threshold with different ports

  !

  access-list 1 permit 192.168.2.0 0.0.0.255

  access-list 113 allow host tcp 82. #. #. # host 87. #. #. # eq 22

  access-list 113 permit tcp 84. #. #. # 0.0.0.3 host 87. #. #. # eq 22

  access-list 113 allow host tcp 79. #. #. # host 87. #. #. # eq 22

  access-list 113 tcp refuse any any eq 22

  access-list 113 allow host tcp 82. #. #. # host 87. #. #. # eq telnet

  access-list 113 permit tcp 84. #. #. # 0.0.0.3 host 87. #. #. # eq telnet

  access-list 113 allow host tcp 79. #. #. # host 87. #. #. # eq telnet

  access-list 113 tcp refuse any any eq telnet

  113 ip access list allow a whole

  access-list 121 permit ip 192.168.2.0 0.0.0.255 192.168.3.0 0.0.0.255

  access-list 121 allow ip 192.168.3.0 0.0.0.255 192.168.2.0 0.0.0.255

  !

  control plan

  !

  Line con 0

  line to 0

  line vty 0 4

  transport input telnet ssh

  !

  end

  you have ruled out the IP address of the customer the NAT pool

  either denying them in access list 1

  or do road map that point to the loopback address as a next hop for any destent package for your pool to avoid nat

  first try to put this article in your access-lst 110

  access-list 110 deny 192.168.2.0 0.0.0.255 192.168.3.0 0.0.0.255

  access-list 110 permit 192.168.2.0 0.0.0.255 any

  sheep allow 10 route map

  corresponds to the IP 110

  remove your old nat and type following one

  IP nat inside source overload map route interface fastethernet0 sheep

  rate if useful

  and let me know, good luck

• Traffic of Client VPN routing via VPN Site to Site

  Hello

  We have the following scenario:

  • Office (192.168.2.x)
  • Data Center (212.64.x.x)
  • Home workers (192.168.2.x) (scope DHCP is in the office subnet)

  Connections:

  • Desktop to Data Center traffic is routed through a Site at IPSec VPN, which works very well.
  • Welcome to the office is routed through a Site IPSec VPN Client.

  The question we have right now, is the Client VPN works, and we have implemented a split tunnel which includes only the subnet of the Office for a list of network.

  What I have to do, is to route all traffic to home' to 'Data Center' by site to Site VPN is configured.

  I tried to add the ranges of IP data center to the list of Client VPN Split tunnel, but when I do that and try to connect at home, I just get a "connection timed out" or denied, as if she was protected by a firewall?

  Could you please let me know what I missed?

  Result of the command: "show running-config"
  : Saved
  :
  ASA Version 8.2(5)
  !
  hostname ciscoasa
  domain-name skiddle.internal
  enable password xxx encrypted
  passwd xxx encrypted
  names
  name 188.39.51.101 dev.skiddle.com description Dev External
  name 192.168.2.201 dev.skiddle.internal description Internal Dev server
  name 164.177.128.202 www-1.skiddle.com description Skiddle web server
  name 192.168.2.200 Newserver
  name 217.150.106.82 Holly
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  shutdown
  !
  interface Ethernet0/4
  shutdown
  !
  interface Ethernet0/5
  shutdown
  !
  interface Ethernet0/6
  shutdown
  !
  interface Ethernet0/7
  shutdown
  !
  interface Vlan1
  nameif inside
  security-level 100
  ip address 192.168.2.254 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  ip address 192.168.3.250 255.255.255.0
  !
  !
  time-range Workingtime
  periodic weekdays 9:00 to 18:00
  !
  ftp mode passive
  clock timezone GMT/BST 0
  clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00
  dns domain-lookup inside
  dns server-group DefaultDNS
  name-server Newserver
  domain-name skiddle.internal
  same-security-traffic permit inter-interface
  object-group service Mysql tcp
  port-object eq 3306
  object-group protocol TCPUDP
  protocol-object udp
  protocol-object tcp
  object-group network rackspace-public-ips
  description Rackspace Public IPs
  network-object 164.177.132.16 255.255.255.252
  network-object 164.177.132.72 255.255.255.252
  network-object 212.64.147.184 255.255.255.248
  network-object 164.177.128.200 255.255.255.252
  object-group network Cuervo
  description Test access for cuervo
  network-object host Holly
  object-group service DM_INLINE_TCP_1 tcp
  port-object eq www
  port-object eq https
  object-group service DM_INLINE_TCP_2 tcp
  port-object eq www
  port-object eq https
  object-group service DM_INLINE_TCP_3 tcp
  port-object eq www
  port-object eq https
  object-group service DM_INLINE_TCP_4 tcp
  port-object eq www
  port-object eq https
  access-list inside_access_in extended permit ip any any
  access-list outside_access_in remark ENABLES Watermark Wifi ACCESS TO DEV SERVER!
  access-list outside_access_in extended permit tcp 188.39.51.0 255.255.255.0 interface outside object-group DM_INLINE_TCP_4 time-range Workingtime
  access-list outside_access_in remark ENABLES OUTSDIE ACCESS TO DEV SERVER!
  access-list outside_access_in extended permit tcp any interface outside object-group DM_INLINE_TCP_3
  access-list outside_access_in remark Public Skiddle Network > Dev server
  access-list outside_access_in extended permit tcp 192.168.3.0 255.255.255.0 interface outside eq www
  access-list outside_access_in extended permit tcp object-group rackspace-public-ips interface outside eq ssh
  access-list outside_access_in remark OUTSIDE ACCESS TO DEV SERVER
  access-list outside_access_in extended permit tcp object-group Cuervo interface outside object-group DM_INLINE_TCP_1 inactive
  access-list outside_access_in extended permit tcp 192.168.3.0 255.255.255.0 host dev.skiddle.internal object-group DM_INLINE_TCP_2 inactive
  access-list inside_access_in_1 remark HTTP OUT
  access-list inside_access_in_1 extended permit tcp any any eq www
  access-list inside_access_in_1 remark HTTPS OUT
  access-list inside_access_in_1 extended permit tcp any any eq https
  access-list inside_access_in_1 remark SSH OUT
  access-list inside_access_in_1 extended permit tcp any any eq ssh
  access-list inside_access_in_1 remark MYSQL OUT
  access-list inside_access_in_1 extended permit tcp any host 164.177.128.200 object-group Mysql
  access-list inside_access_in_1 remark SPHINX OUT
  access-list inside_access_in_1 extended permit tcp any host 164.177.128.200 eq 3312
  access-list inside_access_in_1 remark DNS OUT
  access-list inside_access_in_1 extended permit object-group TCPUDP host Newserver any eq domain
  access-list inside_access_in_1 remark PING OUT
  access-list inside_access_in_1 extended permit icmp any any
  access-list inside_access_in_1 remark Draytek Admin
  access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 4433
  access-list inside_access_in_1 remark Phone System
  access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 35300 log disable
  access-list inside_access_in_1 remark IPSEC VPN OUT
  access-list inside_access_in_1 extended permit udp any host 94.236.41.227 eq 4500
  access-list inside_access_in_1 remark IPSEC VPN OUT
  access-list inside_access_in_1 extended permit udp any host 94.236.41.227 eq isakmp
  access-list inside_access_in_1 remark Office to Rackspace OUT
  access-list inside_access_in_1 extended permit ip 192.168.2.0 255.255.255.0 object-group rackspace-public-ips
  access-list inside_access_in_1 remark IMAP OUT
  access-list inside_access_in_1 extended permit tcp any any eq imap4
  access-list inside_access_in_1 remark FTP OUT
  access-list inside_access_in_1 extended permit tcp any any eq ftp
  access-list inside_access_in_1 remark FTP DATA out
  access-list inside_access_in_1 extended permit tcp any any eq ftp-data
  access-list inside_access_in_1 remark SMTP Out
  access-list inside_access_in_1 extended permit tcp any any eq smtp
  access-list outside_1_cryptomap extended permit ip 192.168.2.0 255.255.255.0 object-group rackspace-public-ips
  access-list inside_nat0_outbound extended permit ip 192.168.2.0 255.255.255.0 192.168.100.0 255.255.255.0
  access-list inside_nat0_outbound extended permit ip 192.168.2.0 255.255.255.0 object-group rackspace-public-ips
  access-list inside_nat0_outbound extended permit ip any 192.168.2.128 255.255.255.224
  access-list inside_1_cryptomap extended permit ip 192.168.2.0 255.255.255.0 object-group rackspace-public-ips
  access-list outside_1_cryptomap_1 extended permit tcp 192.168.2.0 255.255.255.0 object-group rackspace-public-ips eq ssh
  access-list RACKSPACE-cryptomap_1 extended permit ip 192.168.2.0 255.255.255.0 object-group rackspace-public-ips
  access-list RACKSPACE-TEST extended permit ip host 94.236.41.227 any
  access-list RACKSPACE-TEST extended permit ip any host 94.236.41.227
  access-list InternalForClientVPNSplitTunnel remark Inside for VPN
  access-list InternalForClientVPNSplitTunnel standard permit 192.168.2.0 255.255.255.0
  access-list InternalForClientVPNSplitTunnel remark Rackspace
  access-list InternalForClientVPNSplitTunnel standard permit 164.177.128.200 255.255.255.252
  access-list InternalForClientVPNSplitTunnel remark Rackspace
  access-list InternalForClientVPNSplitTunnel standard permit 164.177.132.16 255.255.255.252
  access-list InternalForClientVPNSplitTunnel remark Rackspace
  access-list InternalForClientVPNSplitTunnel standard permit 164.177.132.72 255.255.255.252
  access-list InternalForClientVPNSplitTunnel remark Rackspace
  access-list InternalForClientVPNSplitTunnel standard permit 212.64.147.184 255.255.255.248
  pager lines 24
  logging enable
  logging console debugging
  logging monitor debugging
  logging buffered debugging
  logging trap debugging
  logging asdm warnings
  logging from-address [email protected]/* */
  logging recipient-address [email protected]/* */ level errors
  mtu inside 1500
  mtu outside 1500
  ip local pool CiscoVPNDHCPPool 192.168.2.130-192.168.2.149 mask 255.255.255.0
  ip verify reverse-path interface inside
  ip verify reverse-path interface outside
  ipv6 access-list inside_access_ipv6_in permit tcp any any eq www
  ipv6 access-list inside_access_ipv6_in permit tcp any any eq https
  ipv6 access-list inside_access_ipv6_in permit tcp any any eq ssh
  ipv6 access-list inside_access_ipv6_in permit icmp6 any any
  icmp unreachable rate-limit 1 burst-size 1
  icmp permit any outside
  no asdm history enable
  arp timeout 14400
  global (outside) 1 interface
  nat (inside) 0 access-list inside_nat0_outbound
  nat (inside) 1 0.0.0.0 0.0.0.0
  static (inside,outside) tcp interface www dev.skiddle.internal www netmask 255.255.255.255
  static (inside,outside) tcp interface ssh dev.skiddle.internal ssh netmask 255.255.255.255
  access-group inside_access_in in interface inside control-plane
  access-group inside_access_in_1 in interface inside
  access-group inside_access_ipv6_in in interface inside
  access-group outside_access_in in interface outside
  route outside 0.0.0.0 0.0.0.0 192.168.3.254 10
  timeout xlate 3:00:00
  timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
  timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
  timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  timeout floating-conn 0:00:00
  dynamic-access-policy-record DfltAccessPolicy
  aaa authentication telnet console LOCAL
  aaa authentication enable console LOCAL
  http server enable 4433
  http 192.168.1.0 255.255.255.0 inside
  http 192.168.2.0 255.255.255.0 inside
  no snmp-server location
  no snmp-server contact
  snmp-server enable traps snmp authentication linkup linkdown coldstart
  crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
  crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
  crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
  crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
  crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
  crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
  crypto ipsec security-association lifetime seconds 86400
  crypto ipsec security-association lifetime kilobytes 4608000
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set security-association lifetime seconds 28800
  crypto map outside_map 1 match address RACKSPACE-cryptomap_1
  crypto map outside_map 1 set pfs
  crypto map outside_map 1 set peer 94.236.41.227
  crypto map outside_map 1 set transform-set ESP-AES-128-SHA
  crypto map outside_map 1 set security-association lifetime seconds 86400
  crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
  crypto map outside_map interface outside
  crypto ca trustpoint _SmartCallHome_ServerCA
  crl configure
  crypto ca certificate chain _SmartCallHome_ServerCA
  certificate ca xxx
  quit
  crypto isakmp enable outside
  crypto isakmp policy 10
  authentication crack
  encryption aes-256
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 20
  authentication rsa-sig
  encryption aes-256
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 30
  authentication pre-share
  encryption aes-256
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 40
  authentication crack
  encryption aes-192
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 50
  authentication rsa-sig
  encryption aes-192
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 60
  authentication pre-share
  encryption aes-192
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 70
  authentication crack
  encryption aes
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 80
  authentication rsa-sig
  encryption aes
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 90
  authentication pre-share
  encryption aes
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 100
  authentication crack
  encryption 3des
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 110
  authentication rsa-sig
  encryption 3des
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 120
  authentication pre-share
  encryption 3des
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 130
  authentication crack
  encryption des
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 140
  authentication rsa-sig
  encryption des
  hash sha
  group 2
  lifetime 86400
  crypto isakmp policy 150
  authentication pre-share
  encryption des
  hash sha
  group 2
  lifetime 86400
  telnet 192.168.1.0 255.255.255.0 inside
  telnet 192.168.2.0 255.255.255.0 inside
  telnet timeout 5
  ssh timeout 5
  console timeout 0
  dhcpd auto_config outside
  !
  dhcprelay server 192.68.2.200 inside
  threat-detection basic-threat
  threat-detection scanning-threat
  threat-detection statistics host
  threat-detection statistics access-list
  threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
  ntp server 194.35.252.7 source outside prefer
  webvpn
  port 444
  svc image disk0:/anyconnect-macosx-i386-2.4.1012-k9.pkg 1 regex "Intel Mac OS X"
  group-policy DfltGrpPolicy attributes
  vpn-tunnel-protocol IPSec webvpn
  group-policy skiddlevpn internal
  group-policy skiddlevpn attributes
  dns-server value 192.168.2.200
  vpn-tunnel-protocol IPSec l2tp-ipsec
  split-tunnel-policy tunnelspecified
  split-tunnel-network-list value InternalForClientVPNSplitTunnel
  default-domain value skiddle.internal
  username bensebborn password *** encrypted privilege 0
  username bensebborn attributes
  vpn-group-policy skiddlevpn
  username benseb password gXdOhaMts7w/KavS encrypted privilege 15
  tunnel-group 94.236.41.227 type ipsec-l2l
  tunnel-group 94.236.41.227 ipsec-attributes
  pre-shared-key *****
  tunnel-group skiddlevpn type remote-access
  tunnel-group skiddlevpn general-attributes
  address-pool CiscoVPNDHCPPool
  default-group-policy skiddlevpn
  tunnel-group skiddlevpn ipsec-attributes
  pre-shared-key *****
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  policy-map type inspect dns preset_dns_map
  parameters
  message-length maximum client auto
  message-length maximum 512
  policy-map global_policy
  class inspection_default
  inspect dns preset_dns_map
  inspect ftp
  inspect h323 h225
  inspect h323 ras
  inspect rsh
  inspect rtsp
  inspect esmtp
  inspect sqlnet
  inspect skinny
  inspect sunrpc
  inspect xdmcp
  inspect sip
  inspect netbios
  inspect tftp
  inspect ip-options
  policy-map global-policy
  class inspection_default
  inspect icmp
  inspect icmp error
  inspect ipsec-pass-thru
  inspect ftp
  !
  service-policy global_policy global
  smtp-server 164.177.128.203
  prompt hostname context
  call-home reporting anonymous
  Cryptochecksum:6c2eb43fa1150f9a5bb178c716d8fe2b
  : end
  

  You must even-Security-enabled traffic intra-interface to allow communication between vpn VPN.

  With respect,

  Safwan

  Remember messages useful rate.

• Router w / Tunnel dynamic L2L and Clients VPN

  I have a 7200 router currently configured w / vpn clients. I'm looking to add a tunnel dynamic l2l. When I do, I am more able to connect using the vpn client. I following the configuration the following URL.

  http://Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a00801dddbb.shtml

  As soon as I add...

  Crypto-map dynamic dynmap 5

  Define VPNclient isakmp-profile

  the vpn client no longer works. Have not access to the config right now as I took it. Someone at - it it works correctly?

  Okay, mhhh I think that this is a problem with the configuration, give a shot at one of the L2L bouncing, set it to the profile and the keychain, which is the result.

• Client VPN router 1841 will not establish tunnel

  We have a 1841 with IOS 12.4 (3) we have been unable to establish a tunnel to using the 4.8.01.0300 version. It will not exchange keys ISAKMP whatever we use parameters. Debugging is a variety of errors including poorly matched to encryption, authentication, etc. It will not match even the default isakmp policy!

  Here are the relevant parts of the config

  No aaa new-model

  !

  resources policy

  crypto ISAKMP policy 10

  BA aes 256

  preshared authentication

  Group 2

  !

  crypto ISAKMP policy 100

  md5 hash

  preshared authentication

  Group 2

  !

  Configuration group Xclient crypto isakmp client

  test key

  pool vpnpool

  ACL 101

  !

  Crypto ipsec transform-set esp - aes 256 esp-sha-hmac AES256-SHA

  !

  Crypto-map dynamic dyn_map 15

  game of transformation-AES256-SHA

  market arriere-route

  !

  !

  launch of the RA_map client configuration address card crypto

  client configuration address card crypto RA_map answer

  map RA_map 15-isakmp ipsec crypto dynamic dyn_map

  interface FastEthernet0/0

  Description "field.

  IP x.x.x.x 255.255.255.248

  IP access-group 150 to

  inspect the IP default100 in

  NAT outside IP

  IP virtual-reassembly

  automatic duplex

  automatic speed

  card crypto RA_map

  And an example on Isakmp debug:

  * 21:53:47.903 Jun 28: ISAKMP: (0:0:N / A:0): audit ISAKMP transform 14 against priority policy 100

  * 21:53:47.903 Jun 28: ISAKMP: DES-CBC encryption

  * 21:53:47.903 Jun 28: ISAKMP: MD5 hash

  * 21:53:47.903 Jun 28: ISAKMP: group by default 2

  * 21:53:47.903 Jun 28: ISAKMP: pre-shared key auth

  * 21:53:47.903 Jun 28: ISAKMP: type of life in seconds

  * 21:53:47.903 Jun 28: ISAKMP: life (IPV) 0x0 0 x 20 0xC4 0x9B

  * 21:53:47.903 Jun 28: ISAKMP: (0:0:N / A:0): pre-shared authentication offered but does not match policy.

  * 21:53:47.903 Jun 28: ISAKMP: (0:0:N / A:0): atts are not acceptable. Next payload is 0

  * 21:53:47.903 Jun 28: ISAKMP: (0:0:N / A:0): audit ISAKMP transform 1 against priority policy 65535

  We cannot understand why the router will not match the pre-shared authentication setting, or any other parameter (encryption, hash etc.) we change.

  We tried to remove the NAT and ACLs nothing helps... What Miss me?

  Thanks

  There are various debug command? Crypto engine for debugging? Displays information about the cryptographic engine, for example what Cisco IOS software performs encryption or decryption operations. ? Debug crypto ipsec. For more information, see the following URL

  http://www.Cisco.com/en/us/products/ps6350/products_configuration_guide_chapter09186a0080455b04.html

• Client VPN does not install

  Greetings,

  Try to install the VPN clinet version 5.0.07.0290 on WinXP box.

  Gets to a certain point then - error

  Error 27850.  Unable to manage the network components.

  The corruption of the operating system can prevent installation.

  I asked this question here before - and received responses instructioning me to uninstall the client.

  This canoe do since there is no element installed in Add / Remove programs to point to uninstall.  I deleted the folder created, but it makes no difference - each time the system stops at the same point.

  Any other ideas?

  Is your Windows XP 32-bit or 64-bit?

  There are 2 version of VPN Client 5.0.07.0290:

  32-bit: vpnclient-win-msi - 5.0.07.0290 - k9.exe

  64-bit: vpnclient-winx64-msi - 5.0.07.0290 - k9.exe

  Please, please make sure you use the right software.

  Here are the steps that will allow the uninstall:

  (1) remove the VPN Client (any version) of the machine using the MSI cleanup tool
  http://support.Microsoft.com/kb/290301

  Updated the DNE using this deterministic networks link
  http://www.deterministicnetworks.com/support/dnesupport.asp

  Run the WINFIX application, then the upgrade DNE.

  (2) take a backup of the registry.
  (3) on your desktop, click Start > run and type regedit.
  (4) delete the following keys:

  (a) go to HKEY_LOCAL_MACHINE > SOFTWARE > Cisco Systems > customer VPN.
  (b) go to HKEY_LOCAL_MACHINE > SOFTWARE > deterministic networks and remove the keys.
  Note: Sometimes the system will not allow deletion of this key.

  (c) go to HKEY_LOCAL_MACHINE > SOFTWARE > Microsoft > Windows > CurrentVersion > uninstall > {5624c000-b109-11d4-9db4-00e0290fcac5}.
  (d) delete all the old files deterministic NDIS Extender (DNE): all files starting with DNE, as all are coming files and Client VPN facilities.

  dne2000.sys %SystemRoot%\system32\drivers
  dne2000m.inf and dne2000m.pnf of %SystemRoot%\inf

  (e) the enumeration of original manufacturers of hardware (OEM) of the dne2000.inf and dne2000.pnf files.

  The OEM enumeration .inf file is a file called ".inf oem (digital value)."
  For example, oem2.inf and oem2.pnf.

  Note: Be sure to remove only the DNE OEM files.

  dneinobj.dll % SystemRoot%\system32. You may need to reboot for this file can be deleted.

  (f) delete the following file: cvpndrv.sys to %SystemRoot%\system32\drivers

  (5) reboot the machine.

  (6) find the file CSGina.dll in the system32 folder rename it to CSGina.old

  7-restart the machine.

  (8) to disable any firewall if not installed.

  Hope that helps.

• Impossible to establish a VPN connection with a router configured as a Cisco server using client VPN 5.0.00.0340

  Hei guys,.

  Please help me on this one because I'm stuck enough on her...

  I am trying to connect to a Cisco 3700 router configured as a VPN server by using a VPN client and the VPN connection does not settle.

  This is an extract from the log:

  130 12:48:30.585 07/01/11 Sev = Info/5 IKE / 0 x 63000001
  Peer supports XAUTH
  131 12:48:30.585 07/01/11 Sev = WARNING/3 IKE/0xE3000057
  The HASH payload received cannot be verified
  132 12:48:30.600 07/01/11 Sev = WARNING/2 IKE/0xE300007E
  Failed the hash check... may be configured with password invalid group.
  133 12:48:30.600 07/01/11 Sev = WARNING/2 IKE/0xE300009B
  Impossible to authenticate peers (Navigator: 904)
  134 12:48:30.600 07/01/11 Sev = Info/4 IKE / 0 x 63000013
  SEND to > ISAKMP OAK INFO (NOTIFY: INVALID_HASH_INFO) for 200.100.50.173

  I enclose the whole journal extract... The message "BOLD" is quite obvious, you mean, but I'm 100% sure, in the login entry, I typed correctly the group password: pass

  My topology is very basic, as I am setting this up only to get a clue of the operation of the Cisco VPN. It is built in GNS3:
  -2 3700 routers: one of them holds the configuration of the VPN server and the other would be the ISP through which the remote worker would try to establish a VPN connection. I am also attaching the configuration file for the router configured as a VPN router.

  Behind the second router there is a virtual XP machine on which I have installed VPN client...

  My connection entry in the customer is to have the following parameters:
  Host: 200.100.50.173 , //which is the IP address of the VPNServer
  Authentication-> authentication-> name group: grup1 password: pass / / I'm quite positive that I typed the correct password... even if the log messages are linked to a misidentification.

  I use public addresses only, because I noticed there is a question about behind the NAT VPN connections and is not not very familiar to the NAT.

  Another aspect which can be of any importance is that "allow Tunneling of Transport" in the tab Transport to the input connection is disabled

  and the VPNServer router logs the following error message when you try to establish the connection:

  * 01:08:47.147 Mar 1: % CRYPTO-6-IKMP_NOT_ENCRYPTED: IKE 200.100.50.34 package was not encrypted and it should have been.
  * 01:08:47.151 Mar 1: % CRYPTO-6-IKMP_NOT_ENCRYPTED: IKE 200.100.50.34 package was not encrypted and it should have been.
  

  You have no idea why I can't connect? Y at - it something wrong with my configuration of VPN server... or with the connection entry in the VPN client?

  Thank you

  Iulia

  Depending on the configuration of the router, the group name is grup1 and the password is baby.

  You also lack the ipsec processing game that you would need to apply to the dynamic map.

  Here is an example configuration for your reference:

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080235197.shtml

  Hope that helps.

• ProBook 650 1: Problems with W10 upgrade - Client VPN in my notebook?

  Hello

  I upgraded my laptop to Windows 10 but, like many people, I encountered some problems with the Broadcom 802.11 wi - fi adapter. I read a lot of discussion about it and I decide to yestarday to roll back to Windows 7 in order to do a clean update by ISO and unisntall VPN. I read that Cisco VPN Client is the problem when upgrading to W10... but I'm not sure I have the Cisco Client in my notebook.
  You help me find a software which VPN I have in my book?
  I run Microsoft Fixit and found out that I have:
  Cisco PEAP
  Cisco LEAP
  Cisco EAP-FAST

  Is this software VPN? Or not?

  After having updated Broadcom driver on Windows 10 WiFi worked well, but I still had an error message ' Broadcom 802.11 network adapter wi - fi doesn't work "whenever I turned on the laptop.
  In addition, it was impossible on W10 to open the Broadcom Wireless Tool (Control Panel) software, I always get an error message.

  Should I unistall Cisco software?

  See you soon,.

  Marco

  "Hi @Kreiskybill,

  I'm sorry that was meant to be an internal memo that I'm not trained on commercial products and I was hoping one of my colleagues would help, but I'll try my best to help you.

  For your wireless problem, there are several troubleshooting documents available on the page of product support for your ProBook (http://ow.ly/ADK7301hCLl), that might be useful.  Also, here is the 'HP PC' document - troubleshooting wireless network and the Internet (Windows 10) consumer ( http://ow.ly/pIm0301hEIN ) for reference.

  With regard to programs of Cisco that you listed, @SpiritX on the Microsoft Forums ( http://ow.ly/DAhQ301hCFt ) well answer your question about Cisco programs you listed.  I know that you are not running Windows Vista, but the answer is always valid for you.

  If it helps and you want to thank me, please click the 'Thumbs Up' icon to say thank you.  If you think that I helped to solve your problem, please click the button of "acceptable Solution".  This will allow other users to find what worked for you. »

• Cisco and Checkpoint VPN clients on a single PC

  Hello

  I'm in the following fix:

  I had used customer Checkpoint SecuRemote 4.1 SP - 5 VPN in the past.

  Now, I have installed the Cisco VPN client version 4.0.4 on my PC to access IPSec VPN for the PIX in our headquarters.

  According to Cisco VPN release notes http://www.cisco.com/univercd/cc/td/doc/product/vpn/client/rel404/404clnt.htm#wp1346340 , it should be possible to have clients both Cisco and Checkpoint VPN installed on the same machine.

  But I am not able to connect to my PIX, I receive the following error message:

  "Secure the complete VPN connection locally by the Client.

  Reason 403: failed to contact the security gateway. »

  When I'm looking for signs of PC control-> system-> hardware-> device Administration-> network cards, I can see Cisco Systems VPN Adapter disabled.

  After you activate manually, I always get the same error when you try to connect to the Cisco VPN client.

  After PC restart the Cisco VPN adapter is disabled later.

  I tried to uncheck Check Point SecuRemote form my Dial-up connection (bypassing CSCea31192 of bug, but the bug does not affect NAT - T connection which I use).

  I noticed the same situation on three different computers, one running Windows XP, both running Windows 2000.

  After uninstalling the client Checkpoint completely (including Windows registry manual removal), the Cisco VPN client works very well.

  It seems to me, therefore, that there is a profound mismatch between Cisco and Checkpoint VPN clients.

  Does anyone know of a workaround?

  Thank you

  Milan

  We had the same problem with some of our users who need to use the two clients to connect to customer sites.

  If I remember the cisco client does not start automatically, but the client of checkpoint 4.1 don't.

  We by-passed by deleting the registry entry point control that starts the client at startup. fwenc.exe is the entrance and it is in

  HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Run

  After that make a shortcut to the executable file that is stored in the directory \bin to relevant checkpoint on the client (it is different from NT & 9 client x) and then only start when it is necessary.

  Hope that's a help

• Connection with the client VPN for RV110W problem

  Hi guys: I just installed a RV110W router to my small business and I try to connect via VPN from home client.  I was unable to do so, no matter what I try.  Relevant information:

  1. I can connect to the router via remote very well management, so I know that the router is accessible from the Net.

  2. internal address of the router: 10.81.208.1

  3. active PPTP.  PPTP server IP address: 10.0.0.1

  4 IP addresses for PPTP clients: 10.0.0.10 - 14

  5. two VPN clients added - one with PPTP, with the QuickVPN Protocol Protocol.  Both are enabled (and Yes, I triple checked passwords)

  6 encryption MPPE and Netbios active.

  7 IPSec, PPTP and L2TP all active gateways.

  8 VPN client: 1.4.1.2

  9. computer: laptop running Windows 7 family (64-bit), with the firewall Windows is activated.

  10 home network: 192.168.2.196

  It is causing to tear my hair out.  What Miss me?

  Shannon

  Hi Shannon,

  I am pleased to see that you're progress.

  Shannon Rotz wrote:
  I changed the RM port to 443.  Unfortunately, now I can't connect to the router via browser, either by remote management or from the local network - I get the usual "page cannot be displayed".  How do I get back into the router configuration GUI?
  

  You should be able to reach the GUI by typing https://192.168.1.1(assuming that you have not changed the default IP address) normally once you replace http (port 80) with https (port 443) the internal router web server automatically will redirect you to the https page if you type http. Open your command prompt and try to do a ping of the IP address of the router to ensure that it still meets this address

  With regards to the VPN client:   Up until I changed the port, the same error message kept coming up, i.e. "Unable to establish connection" (or something like that), with a list of possible reasons why it couldn't connect. Now the message has changed - I'm getting "Server's certificate doesn't exist on your local computer".  If I continue trying to connect, then it says "Activating Policy", followed by "Verifying Network", then "The remote gateway is not responding.  Do you want to wait?"  This is definitely progress, since I never got this far before.

  You are a quarter inch offline. If you look at the log.txt in C:\Program Cisco Small Business\QuickVPN Client, in my view, you will see "Failed to ping router remote VPN! This means that your PC is blocking the ping to the router response. Usually, if you look at this point the status of Client VPN in the router (first of all need to remote management) you will see that your user status is "connected." If the router thinks that the connection is established, but the PC does not work. You might want to try another PC at this stage to verify that it is indeed a problem with your PC. This problem is usually caused by the 3rd party software antivirus/firewall blocking the ping response. Microsoft Security Essentials can do this as well, so if you turn it off. If you do not have another PC to test from, call Cisco Small Business Support and ask a technician, try to connect to the lab. You can find the number to call here

  On an impulse, I tried setting up a Windows VPN connection, i.e. created a new VPN connection in Network and Sharing Center, using a PPTP client ID that I had created.  That connection actually worked, except for one problem:  I can't see the remote network.  If I could solve that problem, I'll just tell the other clients to use a Windows connection rather than QuickVPN.
  

  Good thought. If you do not see the remote devices, make sure that they do not block VPN connections. (Windows or third-party firewall, antivirus, antispyware) With a connection, PPTP or QuickVPN, you should be able to go to run, type the IP address of the device that you want to connect to (i.e. \\192.168.1.101 ) and see the list of shared folders. After the PPTP connection is established, try to ping the address LAN IP of the router. If it is successful, try to ping a LAN device such as a network printer or a PC. Again, PCs may block ping requests if they have a firewall running watch so for this.

  Answer please if you have any questions.

• UC500 and IPsec VPN client - disconnects

  Just throw a question out there.
  I have a UC560 running uc500-advipservicesk9 - mz.151 - 2.T2 site HQ.  Remote users, about 8 of them, attempt to connect via IPsec VPN (v5.0.07.0440) HQ clients to access files, etc..  The behavior I see is 5 users to connect successfully, but only 5.  As soon as more users trying to connect, they have either:

  1. connect with success for a minutes, then unmold
  2. get a 412, remote peer is not responding
  3. connect, but someone of another session kickoff.

  Users use the same VPN profile, but with names of single user and passwords.

  Here are some of the CPU configs for VPN clients
  Configuration group customer crypto isakmp USER01
  key *.
  DNS 192.168.0.110
  pool USER01_POOL
  ACL USER01_ACL

  local RAUTHEN AAA authentication login
  permission of AAA local RAUTHOR network authenticated by FIS

  Crypto isakmp USER01_PROF profile
  match of group identity USER01
  list of authentication of client RAUTHEN
  RAUTHOR of ISAKMP authorization list.
  client configuration address respond

  crypto ISAKMP policy 1
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  crypto ISAKMP policy 10
  BA aes
  preshared authentication
  Group 2
  lifetime 28800
  crypto ISAKMP policy 100
  BA aes
  preshared authentication
  Group 2
  life 3600
  crypto ISAKMP policy 1000
  BA 3des
  preshared authentication
  Group 2

  I enabled debugging
  Debug crypto ISAKMP
  Debug crypto ipsec

  Here are some of the things that I see on him debugs
  604899: 16:41:13.333 Aug 21: ISAKMP: (2073): HASH payload processing. Message ID = 284724149
  604900: 16:41:13.333 Aug 21: ISAKMP: (2073): treatment protocol NOTIFY DPD/R_U_THERE 1
  0, message ID SPI = 284724149, a = 0x8E7C6E68
  604901: 16:41:13.333 Aug 21: ISAKMP: (2073): error suppression node 284724149 FALSE reason 'informational (en) State 1.
  604902: 16:41:13.333 Aug 21: ISAKMP: (2073): entry = IKE_MESG_FROM_PEER, IKE_INFO_NOTIFY
  604903: 16:41:13.333 Aug 21: ISAKMP: (2073): former State = new State IKE_P1_COMPLETE = IKE_P1_COMPLETE

  581504: 16:59:12.805 Aug 20: ISAKMP: (2147): purge the node-1455244451
  581505: 16:59:12.805 Aug 20: ISAKMP: (2147): purge the node 840814618
  581506: 16:59:13.933 Aug 20: ISAKMP (2147): received 201.195.231.162 packet dport 4500 sport 37897 Global (R) QM_IDLE
  581507: 16:59:13.933 Aug 20: ISAKMP: node set 801982813 to QM_IDLE
  581508: 20 August 16:59:13.933: ISAKMP: (2147): HASH payload processing. Message ID = 801982813
  581509: 16:59:13.933 Aug 20: ISAKMP: receives the payload type 18
  581510: 16:59:13.933 Aug 20: ISAKMP: (2147): treatment remove with load useful reason
  581511: 16:59:13.933 Aug 20: ISAKMP: (2147): remove the doi = 0
  581512: 16:59:13.933 Aug 20: ISAKMP: (2147): remove Protocol id = 1
  581513: 16:59:13.933 Aug 20: ISAKMP: (2147): remove spi_size = 16
  581514: 16:59:13.933 Aug 20: ISAKMP: (2147): remove the spis num = 1
  581515: 16:59:13.933 Aug 20: ISAKMP: (2147): delete_reason = 2
  581516: 20 August 16:59:13.933: ISAKMP: (2147): load DELETE_WITH_REASON, processing of message ID = 801982813, reason: DELETE_BY_USER_COMMAND
  581517: 16:59:13.933 Aug 20: ISAKMP: (2147): peer does not paranoid KeepAlive.

  581518: 16:59:13.933 Aug 20: ISAKMP: (2147): peer does not paranoid KeepAlive.

  581519: 16:59:13.933 Aug 20: ISAKMP: (2147): removal of State of SA reason 'Order BY user' (R) QM_IDLE (post 201.195.231.162)
  581520: 16:59:13.933 Aug 20: ISAKMP: (2147): error suppression node 801982813 FALSE reason 'informational (en) State 1.
  581521: 16:59:13.933 Aug 20: ISAKMP: node set-878597687 to QM_IDLE
  581522: 20 August 16:59:13.937: ISAKMP: (2147): lot of 201.195.231.162 sending peer_port my_port 4500 37897 (R) QM_IDLE
  581523: 16:59:13.937 Aug 20: ISAKMP: (2147): sending a packet IPv4 IKE.
  581524: 16:59:13.937 Aug 20: ISAKMP: (2147): purge the node-878597687
  581525: 16:59:13.937 Aug 20: ISAKMP: (2147): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
  581526: 16:59:13.937 Aug 20: ISAKMP: (2147): former State = new State IKE_P1_COMPLETE = IKE_DEST_SA

  I opened a case with TAC on this and they do not understand what is the cause.  For them, it looks like a bug without papers.  And their recommendation is to reboot, upgrade or try configuring L2TP for remote users.

  Thank you

  JP

  JP,

  An update of IOS is worth it, even if him debugs seems to indicate that there is a problem with the client. If possible, I always suggest test with another client to see if it is unique to the Cisco VPN Client on Win7. Regarding the limit of 20 tunnel, it is very probably the number of IPsec security associations. If you issue a 'show crypto eli', this example displays the number of Sessions that are currently active IPSec.

  HTH,

  Frank

• Client VPN with tunneling IPSEC over TCP transport does not

  Hello world

  Client VPN works well with tunneling IPSEC over UDP transport.

  I test to see if it works when I chose the VPN client with ipsec over tcp.

  Under the group policy, I disabled the IPSEC over UDP and home port 10000

  But the VPN connection has failed.

  What should I do to work VPN using IPSEC over TCP

  Concerning

  MAhesh

  Mahesh,

  You must use "ikev1 crypto ipsec-over-tcp port 10000.

  As crypto isakmp ipsec-over-tcp work on image below 8.3

  HTH