Want desolde/resolder, remove and replace the two damaged usb2 ports

I have a Sat A30 perfect by all means other than 2 USB2 ports on the back that are damaged (black plastic seperaters between connectors jumped) not quite sure why this happened because I was simply unplug the connected usb plugs on both occasions.

The connectors were not especially tight. fault is I have no insulation between copper connectors which are still found in the slots and causes a short circuit, when I plug in a usb device.

I bought a card mother relpacement (damaged) and usb2 connections are OK! Have good technician experience in carring out Soldering/desoldering and has all the tools. Problem is that I have not the slightest idea what connections under the Board of Directors are required to unsolder my damaged usb2 card in order to remove/swop and perform the necessary replacement.

I'm sure I'll be advised to contact an authorized reseller of Tosh. I tried this and they say that they will be already only the motherboard together and the cost is horrible. I would rather make the repair myself that's not rocket science.

The techies out there who could counsel with picture of the relevent pins to desoldering in order to remove and repair the fault would be greatly appreciated.

E-mail: [email protected]

If you can help in any way or point me in the right direction to go repair.

I hope someone can help. Thank you very much
Stewart

Hello

Please don't be crazy about me, but in my opinion, is not a very good idea to open the notebook alone if you don't have a lot of experience with it. Laptops are designed on the specific way and exchange of material is not so easy as the exchange of material to work stations.

Believe me that a small error in the assembly/disassembly procedure can case damage to equipment or the façade of the same laptop parts. I know that there's not much service partner assistance because they want to do. It costs money, but you must understand that if they give that kind of advice or information they may close the shop very soon.

You can try to do it alone, but at your own risk and be careful.

Tags: Toshiba

Similar Questions

  • Satellite A30 921: how to remove and replace the memory?

    Hi, can someone help me how to remove and replace the memory of satellite A30 921. and also, please give a detailed instruction.

    Thank you in advance.

    Hello

    There is not much to explain. On the low side in the Middle it is placed to cover memory (fixed with two screws). Remove the cover and you will see 2 slots there. I put t know how much memory you here but like Stefan says you can use max 2 GB of RAM (2 x 1024Mo PC2700 - PA3313U-1M1G). How to remove the memory modules, which you can see on http://www.hardwaresecrets.com/article/189/5

    Good bye

  • Laptop HP Touchsmart 15-D020: how to remove and replace the keyboard on laptop HP Touchsmart 15-D020NR

    I spilt a drink on my keyboard and now I can not turn off the caps lock and a number of keys does not work. I need instructions on how to remove and replace the keyboard frame. Thank you.

    On your page of support-look for Maintenance and Service of Guide in the manuals.

    http://support.HP.com/us-en/product/HP-15-D000-TouchSmart-notebook-PC-series/6627588/model/6761859/manuals

  • Steps to remove and replace the keyboard. HP Pavilion dv7-1448dx

    Hello. I have HP Pavilion dv7-1448dx. I have not available a manual where the path is directed to change the laptop keyboard. I need help to get the steps to remove and replace the keyboard. Please provide me with the support as soon as possible so that I can solve this problem. Thank you.

    Link to the .pdf manual

    Click above. We are not HP, all other users trying to help.

  • G61 does not illuminate unless I have remove and replace the battery.

    Even when the power cord plugged in it will not light. If I remove and replace the battery it lights mode battery and AC. At the same time my HP Support Advisor and HP s Advisor "stopped working".

    I restore to a previous point, no help. Downloaded a new HP advisor, ho help.

    This happened after the recent big WIN7 updated. Help

    Hello

    In the Menu start, open the all programs, open accessories, right-click on command prompt and select "run as Administrator".  In at the prompt, type the following command and press ENTER.

    sfc/scannow                (Note that there is a space between sfc and /)

    Let the entire process, then the output type and press ENTER.  Stop the laptop, unplug the AC adapter unplugged, remove the battery and then press and hold the power button for a minute.

    Now, plug in the AC adapter without the battery inserted, start Notepad, open windows control panel, open Device Manager, expand the entry for the battery, on the right, click on and compatible Microsoft ACPI control method battery and select Uninstall - do uninstall not something else here.  When the uninstall is complete, shut down the PC, unplug the AC adapter, reinsert the battery and then start the PC on just the battery.  Windows will automatically reinstall the driver - leave Windows running for a few minutes. Shut down the PC again.  Now plug the power adapter (with the inserted battery always) and start the laptop to see if it helped the issue at all.

    Kind regards

    DP - K

  • How to remove and replace the internal Blu - Ray DVD RW drive on laptop HP HDX 16 t

    The internal dvd player does not work and I would like to remove and replace it myself. If anyone has a method step by step for me, or links to pictures or videos of the steps, I'd appreciate it. Thank you

    RayCE

    There is a screw on the bottom of the laptop that holds the drive in the screw about 4 inches from the front of the dvd player door.on the botom of the machine, remove the screw and remove the disc.

  • How to remove and replace the missing keys Sat A30

    Hey folk,
    I guess that sounds simple, but I have just no idea.
    Broke and need to replace a couple of keys on my keyboard UK A30. At present, all what I have in place are the rubber bubble popper & locators of metal set in the empty spaces.
    The keys in question are the shift (I have no u lying in spring form) and? + / keys of RHS of KB.

    I have complete German and American replacement KBs, but to remove the necessary keys on the part and repair the United Kingdom KB.

    I don't want to end up with 3 broken KBs

    So I need clear and detailed instructions on removal and then reset the necessary keys.

    Any help or direction to the site that contains this kind of info would be greatly appreciated. Or response message directly by email to

    [email protected]

    Thank you very much.
    sparkiefive

    Hello

    I think you should go to a Toshiba Service partner.

    You can find them here:
    https://EU.computers.Toshiba-Europe.com
    Downloads support & - find an approved service

  • Mail and sharing of WIndows 8 has stopped working when I changed my Yahoo password. Can't remove and replace the account information from Yahoo either. Any suggestions?

    I was doing very well with Windows 8 and really liked the tile part until the part of so many mail no longer works when I changed my Yahoo password (after having hacked).  Given that the Yahoo account has been used to set up my Microsoft Account for the new computer laptop / Windows 8, this old password appears to be caught in the trap in the system.  I can still use the browser to get to Yahoo use e-mail like this, but it is frustrating that the Mail tile is now useless and hand tile is too.

    Hello Rob,

    The Microsoft Account and Yahoo accounts are two separate accounts.  Then the two accounts use the same login ID (your Yahoo email address) and can be configured with the same password; When you change the password for one of the accounts that will not change your password for the account on the other.

    If the two accounts used the same password, I suggest to change the password for your Microsoft account and using a separate password for each.

    Once the Microsoft Account password has been changed, you should be able to connect to the mail. You may still need to update your email Yahoo mail password of: charms-> settings-> accounts-> .

    Mark

  • How to remove and replace the hard drive on a desktop Pavilion m9350f computer?

    not boot BIOS says search for device.  . Suspect problem is intermittent

    ShortTimer,

    I was trying to be polite and doesn't cause any anxiety. I asked if the BIOS can 'see' the hard drive and DVD player. (Forget the PMD, USB).

    As your motherboard is a M2N78 - LA. There was a race of (IMHO) production of chips from NVidia controller that were defective. Only this can explain the success or Miss boards failed in these units:

    This series of motherboard has been installed in many different models of HP computers. There are problems.

    http://h30434.www3.HP.com/T5/desktop-hardware/m8530f-desktop-PC-with-a-M2N78-la-mother-board-doesn-t-see/TD-p/181716

    Here are the models reported with the guidance of M2N78LA failed. This is not the complete list.

    a4316f

    e9140f

    p5210y

    p6130y

    p6142p

    p6157c

    p6210f

    p6210y

    p6214c

    p6310y

    p6320y

    a6720y

    m8530f

    m9120y

    m9350f

    m9517c

    m9530f

    m9840sc

  • I have different bookmarks I want to keep on each computer, synchronization will delete the bookmarks on a single computer and replace the bookmarks from another computer in their place

    I have not yet used sync, but I sense it's going to be a problem if I do. I have different bookmarks I want to keep it on each computer. Sync will delete the bookmarks on a single computer and replace the bookmarks from another computer in their place? So I think that will erase the bookmarks on the second computer you configured to synchronize. Is there a way to merge bookmarks on every computer in the library of a bookmark that contains all bookmarks on both computers, so I'm not all bookmarks in sync?

    Just to be clear, this is something that we have commented several times in the forum, Firefox Sync adds everything that is already in the device for the account and pushes this info for the rest of the devices.

    So if you have 2 computers with data X and the other with the data from there, once you set up synchronization in both computers you will have X + Y at the same time.

    I hope that clarifies the doubts...

  • cartridge in the slot on the left is not intended to be used with this printer. Remove and replace

    Hello

    After using my printer on a regular basis and without any problem, I suddenly had this coming message: "cartridge in the slot on the left is not intended for use in this printer. Remove and replace.

    I have a computer that is running Windows 7, 64-bit and the cartridges that I use are all genuine HP cartridges, black and tricolor cartridges are XL.

    What surprises me the most, is that the left cartridge is not empty, I without touching it, there was no jam paper, or any other poor behaviour of the printer. It happened just in the middle of printing, the printer just finished a job, and was about to start the second in the queue. Maybe this detail can help or it's just a coincidence...

    Thank you for your help

    Tonphilou

    Hello

    Please follow the steps in the document below.

    http://support.HP.com/us-en/document/c00042821

  • removed and replaced index page old index is always on the web

    removed and replaced index page old index is always on the web. I just after a new website, but BusinessCatalyst blinking an error message to fast as follows by saying I can't. I thought Muse for coders and technicians.

    Steven,

    The page could be cached in other places, such as cache network or your internet provider.  These are rare cases, but they happen, and you have no control over it.  Best to have friends / colleagues check from another place, this page has been replaced by fact.  If you have several locations showing the same old page, which means the page was either not removed properly, or home page of the site is perhaps used a different directory than where you are currently working.  It is common for people to create several directories test when booting with web creation programs and forget the one that serves content for the online site.

  • Remove and reinsert the battery to reboot the computer from sleep mode

    When the computer goes into mode "sleep" due to inactivity, it cannot be started again until I completely remove and reinsert the battery. It is an Acer laptop with Windows 7 OS

    Hello

    References to Vista also apply to Windows 7.

    1 I want to erase the General corruption and repair/replace damaged/missing system files:

    Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
    generates in Windows Vista cbs.log
    http://support.Microsoft.com/kb/928228

    Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    -------------------------------------------

    Check the settings (BIOS/CMOS) that you can start and ensure that this suite of lan, Wake on modem and
    similar are not enabled.

    Shoot sleep problems - hibernation
    http://www.computerperformance.co.UK/Vista/vista_hibernate.htm

    How to solve a problem of Mode for Vista and find a Solution
    http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.html

    How to enable and disable Hibernation - you can try to disable and re-enable the it. http://www.Vistax64.com/tutorials/165508-hibernation-enable-disable.html

    How to restore the default power in Vista (and then go back and change as you wish)
    http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

    How to troubleshoot performance problems with sleep, hibernation and resume in Windows Vista
    http://support.Microsoft.com/kb/950686

    Panel configuration-Device Manager - look at the settings for the network card, WiFi, Modem power management.
    and other devices. (Double click on the device and the power management tab)

    Panel configuration-Control Panel Home view (non-conventional) in the top-right search pane
    type of hibernation - see turn Hibernate on / off

    All the default power plans and then set them as you wish.

    I hope this helps.
    Rob - bicycle - Mark Twain said it is good.

  • Replace the two drives in a Poweredge T110 II

    Hello

    I am running Windows server 2008 r2 on a Poweredge t110 II server. We had problems with our system crashing a lot lately and it seems to be a problem of hard drive so I replace the two players in our system.

    I watched a previous thread on this-

    http://en.community.Dell.com/support-forums/servers/f/1466/p/19529142/20465311#20465311

    but the Administration of server to manage open, nothing is displayed on the storage tab.

    Can someone help me with this problem?

    You do not use a RAID controller. The disks are connected to the SATA controller on the system board. I see nothing to suggest that these disks are in a RAID array. It seems that these disks are connected like a normal desktop system. If you want to replace the readers simply shut you the system down and physically swap disks on.

  • What is the problem with my iphone? He says still no service but my sim card works with other phones, after a reboot it says searching until I have to remove and reinsert the sim ive done all what is the factory reset to open the phone to verify any damag

    IPhone 6 64 gb

    iOS 9.2.1

    The phone says no service but the SIM card works, everything in the phone works except the flash still lights up and flickers sometimes before becoming stable but who don't mind not 'that' much, ive tried factory reset and everything, ive also open the unit and looked for signs of damage, the phone knows there is a SIM card in the phone , but he never says the name of the carrier, also after the restart he said looking and does not stop until I have remove and reinsert the SIM card.

    You can restore the factory state after an iTunes backup

    If this does not resolve the problem then you may want to align on Apple or an approved repair shop

Maybe you are looking for