Want to 750-055XT: new computer does not start

Similar Questions

• Try to install CS4 Design Premium - disabled since the old computer, new computer does not accept my serial number.  Just wasted 2 hours on Adobe help line.

  Try to install CS4 Design Premium - disabled since the old computer, new computer does not accept my serial number.  Just wasted 2 hours on Adobe help line.

  I sent you a private message that will help you (I hope).

  because scammers can continue to check this thread, I don't want to enter here information that could help them and this is the reason why I deleted your last post and sent you a private message.

• Computer does not start after installing new graphics card

  HP-envy h8-1503
  I7 - 3770 k 3.5 GHZ
  10 GB of Ram
  Windows 8.1
  
  I tried to install a new edition of diamond Raedon 7770 to replace my old 7570 and when I try to start the computer I get 6 long beeps and the power light flashes 6 times. Everything is plugged in right and the video card turns on. It will not be output to the screen tho and the computer does not start!

  I fixed it, the problem was the safe boot in my bios, when I disabled the system booted and worked perfectly since! Thanks for the advice tho!

• Computer does not start after installing a new graphics card

  I am owner of a HP Pavilion H8-1020 with a processor intel i7 - 2600 s Windows 7 and am trying to upgrade my Radeon hd 6570 to a Gigabyte AMD Radeon R9 280 OC. I improved my diet for a Corsair CX750 to meet the requirements of power and installed with number. After the installation of the new card, which as far as I can tell is well seated in the pci slot and correctly connected to the PSU, my computer does not start.

  System powers on, all fans of begin to run including the fans on the new graphics card, but it does not begin the boot process, no entry is received at my monitors, no light on the keyboard, my OS starts loading, I can turn off the system without the delay that will flow normally. Then I reinstalled my old graphics card and the computer started as usual.

  Now, assuming that the card is not DOA, which unfourtunatly I have no way to verify, and I'd like to see if it could be another problem before going through the process of restitution. I did some reading on the internet, which helped, but did not help for a technological neophyte like me.  Now, I know a few things that could cause this problem but lack the necessary skills to determine what question is making me. What I've read, these could be possible questions:

  1: my new graphics card is not compatible with my motherboard. It's something I know now that I should have checked before buying and something I should theoretically be able to do it now, but I am at a loss on how to do it. My card is compatible with my motherboard?

  2 could be a BIOS problem. I updated my bios driver with the version provided by the HP site. I am running FRIEND 7.16 05/10/2011.  And from what I've read it might have something to do with my bios to UEFI mode and I would need to go to a legacy mode so he can recognize a new device, is it true? I am extremely wary of messing with my BIOS settings for fear of bricking my system. How can I check my current BIOS settings are and what I should change and how would approach I change them? Will one of these changes affect my system if they are not what is not causing the problem?

  In addition to these issues, anyone know any other matter which may be the cause of the problem that I should look for? Thanks for any help.

  Hello @Eric_Z,

  I can see why you are having problems with your new graphics card, and to get to the fast response that your motherboard is not compatible with the new graphics card that you have purchased. And here's why.

  Your motherboard according to the page HP Pavilion HPE h8-1020 Desktop PC product specifications is the Carmel motherboard, which has the following expansion slots:

  • A PCI Express x 16
  • Three PCI Express x 1 connectors
  • A PCI Express Mini Card x 1

  As there is no version indicated for your PCI Express x 16 it slot means that it is version 1.

  Now, your previous graphics card was a PCI Express 2.1 x 16, which means that it was version 2 and compatible with your PCI Express x 16 slot on your motherboard. However, the new card is PCI Express 3.0 and will not work in your motherboard due to a compatibility break. While the technology is supposed to be compatible there are many cases where it is not, and I'm afraid that you meet one of these cases.

  I am offering an overclock.net article entitled: the final answer to the controversial compatibility of PCIe x 16 version. where your situation has been tested and examined.

  I hope this helps. Have a great day and thank you for display on the HP Forums!

• my computer with windows broken and now my new computer does not have windows, is it possible to get windows on my new computer from my old?

  my computer with windows broken and now my new computer does not have windows, is it possible to get windows on my new computer from my old?

  Hello

  You tell us what type of license you have.

  If the former was preinstalled, NO, you cannot transfer it.

  Read this information:

  If the laptop came with the preinstalled Windows operating system (Dell, HP, Acer, etc.), this product key supplied with the laptop is preinstalled OEM license and is not transferable.

  OEM license/product key (systems of operating pre-installed on Dell, HP, etc.) is related to the first machine it is installed on and dies when dies of this machine.

  The above applies also to OEM system builders licenses.

  License of operating system in detail, that you buy and install yourself, are allowed to be transferred to another machine.

  And retail licenses also can be installed on a machine at one time.

  ___________________________________________________

  And please read this, you can:

  http://www.Microsoft.com/OEM/en-GB/licensing/sblicensing/pages/licensing_faq.aspx#fBid=cbW6pY-wjS6

  See you soon.

• I purchased Adobe Lightroom 5 who arrived on a disc.  My new computer does not have a D drive (for dvd or cd).  I'll be able to download my Lightroom 5 on my new system via an online connection?

  I purchased Adobe Lightroom 5 who arrived on a disc.  My new computer does not have a D drive (for dvd or cd).  I'll be able to download my Lightroom 5 on my new system via an online connection?

  Sure.

  Download it from

  Adobe - Lightroom: For Windows: Adobe Photoshop Lightroom 5.7.1

  Adobe - Lightroom: For Macintosh: Adobe Photoshop Lightroom 5.7.1

  Install and enter your serial number.

• I recently purchased Photoshop elements 13.  My employer just changed my computer (I am allowed and only use my personal computer) and the new computer does not have a CD-ROM drive.  Is it possible to download the software elements on my compu

  I recently purchased Photoshop elements 13.  My employer just changed my computer (I am allowed and only use my personal computer) and the new computer does not have a CD-ROM drive.  Is there a way to download the software items on my computer with the serial number and not the CD? Help!

  You can download the trial and use your serial number of the drive to enable to make full use...

  PSE 13 trial - http://www.adobe.com/cfusion/tdrc/index.cfm?product=photoshop_elements

• Error - NTLDR missing Windows XP Home computer does not start.

  Original title: XP-based computer does not start.

  XP Home does not start after I uninstalled a large file of Samsung mobile phone. I get a missing NTLDR error message and have had a System32 error as well, but there is no DOS prompt that would allow me to access anything whatsoever. Another problem is that I lost my installation CD. I initially bought this Dell PC nine over 6 years ago, so can provide identification details, if necessary program. Could someone tell me how I can make a recovery CD please? (No floppy drive not installed in the PC). To further complicate things (Yes, I know - I created many more problems that we all need), I have to keep my files on the hard disk, so cannot do a complete reformat, unless someone can tell how to save them somehow. My BACK skills could be summed up as "plodder inexperienced but determined!

  The file might be missing or it could just be that XP can't find it if your file system has somehow got corrupted.

  As the forums MS Answers does not prompt for any information system when a new question is asked, we know absolutely nothing about your system.

  Not knowing the basic information a problem prolongs the frustration and the agony of these issues.

  Provide information on your system, the better you can:

  What is your system brand and model?

  What is your Version of XP and the Service Pack?

  Your system have IDE or SATA disks?

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  The question was preceded by a loss of power, aborted reboot or abnormal termination?  (this includes the plug pulling, buttons power, remove the battery, etc.)

  The afflicted system has a working CD/DVD (internal or external) drive?

  System32 error, you see, is what exactly?

  Depends on a few factors, there could be another copy of the file NTLDR in other places on your system, but you have to start on something to find out whether there is or not.

  After answering the above questions, I begin to make a CD from Recovery Console bootable XP by running a chkdsk/r, first on your HARD drive and then see what is left to do.

  Here's how:

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and don't forget (no support for XP not necessary).

  This is not the same as recovery disks that may have come to a store to purchase the system.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD (do not install UniBlue or the Ask Toolbar - never!):

  http://www.ImgBurn.com/

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

• Compaq 6200 PRO MT: Makes the computer does not start after upgrade CPU

  I have the HP Compaq 6200 PRO PC of MT 615114-001 motherboard and processor Intel Celeron CPU (LGA 1155). After I changed the CPU for Intel Core i5 (LGA 1155) computer does not start. He begins a minute (less than one second) and stops again. No beeps. After you have installed the Celeron back everything works fine. i5 CPU is brand new. What can be?

  In my previous post, I explained the reason it has not worked, and listed the CPU that will work.

  HP tests CPU in the laboratory and publishes a list of processors that will work in a notebook.

  Notebook motherboard BIOS has a list of processors that will work. If it is installed, which is not encoded as OK in the BIOS ROM file, then this will not work.

  Processors published (in the maintenance guide & Service for your nttebook series model) are available in models that can be deilvered in State CTO (configured to order).

• computer does not start after installing video card

  I, m new here so please bear with me.  I have a PC HP Pavilion Media Center TV (m7434n) I'm trying to replace the video card (Nvidia GeForce 6200SE with Turbo Cache) in. I am trying to replace it with a Nvidia EVGA 8400GS. I delete all the nvidia drivers, make sure that the pci-e card is used in the implementation. I have then to remove the old card and install a new one. When I try to start the computer, fans turn on but that's all.  There is nothing on the monitor.  The computer does not start. I replaced the power supply bestec 300 watts with a new antec brand 430 watt power supply.  When I reinstalled the old video card, the computer starts ok. I tried to replace the video card with an ATI Radeon HD5550 too and it's the same thing (the computer would not start), reinstall the old card and it starts up fine. Any help would be greatly appreciated.

  Gary,

  You may have a compatibility issue with the ATI HD 5550 and 2006 PC model.  I've seen other posts where ATI 5xxx video card did not work in older HP PCs.

  When you are referring to the installation of the older video card do you mean going back to the integrated video card?  Moving the video cable to the card installed?

  Install the NVIDIA 8400GS and connect the video cable. Now follow the instructions for clear the CMOS.

• You can save a broken computer? My computer does NOT start after the blue hp screen.

  In the past months, my computer has been the object of a freezing randomly, and Ctrl + Alt + Delete does not work. I stopped him via the power button. Sometimes, when I start it again, the computer moniter shows nothing but a black screen and the computer sounds different when it starts normally. When this happens, I turn it off again hit the left side of the desktop and turn on again. Whenever I do this, the computer starts normally, and I go on the computer use.

  Yesterday morning, after a break of 2 days, acess my computer and it is random freezing thing once again. I force close down as one normally do, and the computer does not start and displays the same black screen and the same fan/air weird sound. I stopped him and I hit the side RIGHT this time, I think and when I turn on the computer, the usual blue HP screen appears with the establishment, boot, diagnostics and system recovery things. HOWEVER, after this screen, a black screen will appear with this weird blue symbol on the upper left corner, I have never seen this and it looks like a circle with a triangle and a Pentagon below and it remains essentially on this screen forever. When I try to hit the establishment, boot, diagnostics and the shortcuts to system recovery, on the lower left side of the screen, it says "Menu boot loading...". ' or whatever the shortcut of loading represents, but nothing ever happens. When I press the other keys, this tapping noise comes from the computer at each tap of the keyboard.

  I have no idea what to do, and at this point, my first priority is to save important files on the computer. Does anyone know what is the problem? I want her more than a problem of system rather than a virus problem because refusing the boot black screen thing lasts for years. My computer is 3-4 years. I enclose a sketch of what looks like the weird symbol.

  

  MY COMPUTER WORKS NOW!

  With the flash drive, I was able to access the BIOS, which before, I couldn't.

  Eventually my computer was in some strange sort of lockdown setting, I switched it back to activate and now its work! I remember save important things in the future. Thank you very much for your help!

• Help! My computer does not start

  My computer does not start. I get a message about missing files. What can I do?

  You may be able to perform a startup repair.

  Startup Repair is a Windows Vista recovery tool that can fix certain problems, such as system files missing or damaged, that might prevent Windows from starting correctly. When you run the Startup Repair, it scans your computer for the problem and then tries to fix it so that your computer can start correctly.

  Startup Repair is located in the System Recovery Options menu, which is located on the Windows Vista installation disc. If your computer manufacturer has preinstalled the recovery options, Startup Repair can also be installed on your hard drive. If your computer does not have the Startup Repair, your computer manufacturer can have customized or replaced the tool. See the documentation provided with your computer or go to the manufacturer's Web site.

  Please see the following site for more information on using Startup Repair:

  http://windowshelp.Microsoft.com/Windows/en-us/help/5c59f8c1-b0d1-4F1A-AF55-74f3922f3f351033.mspx#ex

  ·         Insert the installation disc.

  ·         Restart your computer.

  ·         Click Start, click the arrow next to the button lock and then click on restart.

  ·         If you are prompted, press any key to start Windows from the installation disc.

  Note: If your computer is not configured to start from a CD or a DVD, see the documentation provided with your computer. You may need to change your computer's BIOS settings.

  ·         Choose your language settings, and then click Next.

  ·         Click on repair your computer.

  ·         Select the operating system you want to repair, and then click Next.

  ·         In the System Recovery Options menu, click Startup Repair. Startup Repair can invite you to make choices as it tries to solve the problem, and if necessary, it may restart your computer, because it makes the repairs.

  If the Startup Repair tool is an option of recovering preinstalled on your computer:

  ·          Remove all floppy disks, CDs and DVDs from your computer and restart your computer.

  ·         Click the Start button, click the arrow next to the button lock and then click on restart.

  ·          Do one of the following:

  o If your computer has a single operating system installed, press and hold the F8 key as your computer restarts. You need to press F8 before the Windows logo appears. If the Windows logo appears, you need to try again by waiting until the Windows logon prompt appears, and then stop and restart your computer.

  o If your computer has multiple operating systems, use the arrow keys to select the operating system you want to repair, and then press and hold F8.

  ·          In the Advanced Boot Options screen, use the arrow keys to highlight repair your computer and press ENTER. (If repair your computer is not listed as an option, then your computer does not include startup as a preinstalled recovery option repair).

  Select a keyboard layout, and then click Next.

  ·          Select a user name and password, and then click OK.

  ·          In the System Recovery Options menu, click Startup Repair. Startup Repair can invite you to make choices as it tries to solve the problem and, if necessary, it may restart your computer, because it makes the repairs.

• I have Windows 7, my computer does not start. I did the Startup Repair and he won't fix it. I did the system configuration information

  I have Windows 7, my computer does not start. I did the Startup Repair and he won't fix it. I did the system configuration information. and that did not help. What to do now? The comment of Bios makes me fear that it could damage my computer forever. What should do? Help, please

  Hi Alan,

  Thanks for posting your query in Microsoft Community.

  I understand that the computer does not restart even after running Startup Repair and I will be happy to answer your query. I appreciate the efforts made to try to make it work. Let me ask you;

  • How do you run the Startup Repair?
  • Do you have Windows 7 repair disc?
  • Remember to no particular change in the computer before the show?
  • Have you plugged an external equipment, except the keyboard and mouse?
  • You are able to start the computer in safe mode?
  • What is the brand and model of the computer?

  Note: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  There could be several reasons why he's not leaving including hardware as well. In addition, it could be because the master boot record (MBR) has been damaged. When you try to use the Startup Repair tool to repair the MBR, the Startup Repair tool indicates that no problem was found or it does not work yet.

  If you have any connected USB flash drive or other external devices connected to the computer, if you please, remove them and try to run the Startup Repair tool.

  If you haven't tried using Windows 7 repair disc, you can try the following:

  1. Insert the Windows 7 disc
  2. restart your computer
  3. When asked if you want to boot from your DVD player, do it.
  4. Select your language, click Next.
  5. click on repair your computer
  6. Select the operating system you want to repair.

  You can also perform the system restore by selecting the restore point when you think it worked very well. System Restore, choose advanced options using the disc.

  Important: When you use system restore to restore the computer to a previous state, the programs and updates that you have installed after this date are deleted.

  I also recommend to contact the computer manufacturer to get the done diagnostic equipment.

  Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.

• Computer does not start. Said diagnosis ci.dll file is corrupt.

  Original title:CI.dll is corrupt

  My computer does not start and goes straight to the Startup Repair. I read the diagnostic tests and get that ci.dll is corrupt. How can I fix this. I can't go in safe mode.

  Hello. If the excellent suggestion of engineering support is not a solution, I might suggest looking at your problem in a different way. If after trying to start sound in different modes and after letting windows to attempt to repair himself using tools, you are at the same point, there is an excellent chance that you have a virus rootfit. This variant of the particular virus causes a loop of endless startup repair.

  I had to deal with exactly the same problem you just this last weekend, and if I do a job of tech on the side that was new to me. I searched the various forumns filled with good information provided by many who are far more experienced than I am, but finished as a result of my guts and succeed. I'm pasting below 'A' solution, it worked for me and if you are comfortable around your PC, it is a completely physical process of 20 minutes (time includes blow and clean the case...) (-8..) So take a look and see if what worked for me might work for you as well. Good day.

  Hello... YOU have a rootkit virus. He goes around, I had to kill one this weekend. Now, my solution, while it is easy for me may not for you. I do a little IT WORKS so I have a converter that transforms all types of disks in usb drives. I just pulled on the desktop player and as soon as I connected it to my laptop, ZoneAlarm on access scanner killed and it was all over. IF you have the possibility of another machine, you can pick up a converter for about $30. If you're like most people, the thought of again is less pleasant to the taste. Now, I am 100% convinced that your repair loop is driven virus, no, but 98% is not bad. Good day!

• M127FW MFP: Computer does not start after the installation of the MFP M127FW

  My computer does not start on my hard drive after installation of my new printer MFP M127FW unless I have first of all disconnect the USB cable between the printer and then turn on the computer.  My BIOS is set to boot from my drive hard, not from a USB key, so that makes installing the drivers M127FW MFP and software do on my computer?  I guess it has something to do with the Smart Install feature.

  "On the printer, press Setup, maintenance, Smart Install and stop."

  It worked.  Thank you.