Want to Phoenix 810-160: USB controller driver
I need the driver for the USB controller to a Phoenix 810-160 desire. the system motherboard is a worm MS-7826 1.0, the device in the "other devices" section manager said there is no driver installed. I tried all the usual bugs, uninstall it, restart, update driver etc. nothing works. Working USB 2.0 ports 3.0 ports do recognize not all devices, but they will slow down load a cell phone when it is connected so that they get the power. Thanks for the help
Hello, go to http://support.hp.com/us-en/drivers/selfservice/hp-envy-phoenix-810-100-desktop-pc-series/5399342/model/6529902
Download USB Intel under section (sp65142) Chipset host controller driver and install.
If it does not please post since the Device Manager hardware ID to find the suitable driver for you.
Tags: HP Desktops
Similar Questions
-
Want to Phoenix 810-160: Jacks Audio does not
The audio jacks on the front and the back of my pc use to operate. But now when I try to play sound through my speakers, that they do not work. So I tried to forget the audio device, but now my speakers do not even appear on playback devices. I also tried to use a headset to make sure it was the audio jacks on headphones did not work either.
I brought your question to the attention of a team within HP. They are likely to ask for information from you to get your information or product serial number. Please search for a private message from a contact HP identified. Also, remember not to publicly display personal information (serial numbers and information).
If you are unfamiliar with the operation of the function of the Forum, private messages you can learn it all here.
Thank you for visiting the Forum from HP Support. -
HP Envy Phoenix 810-160: give up WiFi
I have a HP Envy Phoenix 810-160 that I bought in April of 2014, it came with loaded Windows 8.1. It has a Broadcom BCM4352HMP 801.11 ac 2 x 2 Wi - Fi adapter. It maintains abandon the connection. I have install the driver is 6.30.223.170 from 09/06/2013, I tried updating the driver and it says my driver is up to date. When I go to the available networks list my network is listed under the power of the full signal. It does not connect and says that it can't connect. I turn on/off the device in Device Manager and reboot, then I get anywhere from two minutes to an hour or two of functionality so that it falls new.
I'm going through HP and widows forums forums all day looking for a solution. I followed all the troubleshooting steps I found on the HP and Windows forums, but none were specific to this model PC and a wireless adapter. The only step I have not tried it replace the adapter. computer 8 months, I want to buy a new card from the computer. As it is connected to the internet from the computer, I received, it's only this morning December 26, 2014 that the connection has begun to wane.
I tried to update the driver, uninstall and reinstall the adapter off the blue tooth adapter, currently if I toggle the device once in a relationship and reboot, I get a time where I stay logged in, but eventually, he abandons the connection again.
When I turn on the computer the little indicator white wireless on the front of the computer lights up almost instantly. I see my home network with the power of the full signal and two laptops and my Iphone right next to the computer to connect to the same network with full signal strength.
Hello:
This is the latest driver W8.1 I could find... 6.30.223.227
-
Need for Satellite A60 USB controller driver
Hello
This is my first time here, so please forgive if I look 'amateur' :)
I had to reformat my pc and had a hard time finding drivers.
* I need still a usb controller driver * (code 28 in my device - do not installed Manager!). I'm looking for 2 days now and can't seem to find someone who works.
The funniest is that one of my works of ports usb (the one on the right side), but do not have the other 2 in the back.
Anyboday can help me please?
Thanks a bunch
DEA
Well, there are no special USB drivers.
USB drivers are part of the Microsoft Windows operating system.You must install Microsoft service pack 2 and should update the XP in the current state.
Best regards
-
USB (Controller) driver
I have a laptop of hp 15-d000sia and I can't use a flash drive. It doesn't have a usb controller driver. Product number is F8R32EA and the serial number [redacted]. Help, please!
Hello:
If you have installed Windows 7, you need this driver USB 3.0...
https://Downloadcenter.Intel.com/Detail_Desc.aspx?AGR=Y&DwnldID=23789&keyword=Intel+NUC&lang=eng
-
ProBook 4530 s: need to Win 7 Home premium 64-bit USB controller driver
Hello
I need Win 7 64 bit USB controller driver. This problem was detected on my Probook s 4530 by Microsoft.
The printer has no connection, so I can't print.
Thank you.
Earlier, everything was ok, but as a first step, I installed win 10 and did not work properly, so I uninstalled bak for Win 7 Edition home premium. After that, the computer laptop-printer conection stopped.Hope you can help me.
Hello
Installs:
Renesas Electronics USB 3.0 Host Controller Driver
Concerning
-
Download USB Controller driver
Hello
my computer hp laptop pavilion g6-2241ex I need to download USB controller driver for windows 7 64 bit.
Please help me
Spoiler (Highlight to read)Hello
If you haven't already done so, download and install the Chipset driver from the link below.
Once completed, restart the laptop.
Once rebooted windows, download and install the driver usb 3.0 from the following link.
http://ftp.HP.com/pub/SoftPaq/sp55501-56000/sp55975.exe
Kind regards
DP - K
-
HP 15-r228xn: USB controller driver
Hello guys... Please I need the USB controller driver for my HP 15-r228xn, WIN 7 32 bit
Here are the details
PCI\VEN_8086 & DEV_0F35 & SUBSYS_2213103C & REV_0E
PCI\VEN_8086 & DEV_0F35 & SUBSYS_2213103C
PCI\VEN_8086 & DEV_0F35 & CC_0C0330
PCI\VEN_8086 & DEV_0F35 & CC_0C03
And the Ethernet controller driver
PCI\VEN_10EC & DEV_8136 & SUBSYS_2213103C & REV_07
PCI\VEN_10EC & DEV_8136 & SUBSYS_2213103C
PCI\VEN_10EC & DEV_8136 & CC_020000
PCI\VEN_10EC & DEV_8136 & CC_0200
Thank you all,
Hello:
This USB3 driver should work. It also has 32-bit driver files...
For ethernet, download and install the second driver on the list from the link below...
-
HP ENVY Phoenix 810-160: I can't get the sound to work
I just got the
HP ENVY Phoenix 810-160 and I can not for the life of me get the sound to work. I use it with a HP Envy 23 inch monitor which also has audio Beats and a HDMI cable connection. I went through all the steps on the support page of the monitor and desktop support page. Any help out there? Thanks in advance.
Hello
No, it's going to work, you can not connect computer Office AiO 23 and get a sound of the AiO 23.
Kind regards.
-
Want to Phoenix 810-130qe: Windows 7 drivers for Envy
Hi guys
I use a computer to office 810-130qe want to Phoenix, it was delivered with Win 8. Recently, I replaced a new HARD drive and installed Win 7 64 bit instead.
Need help to download all the right drivers for Windows 7 64 bit please.
Thanks in advance.
Hello:
Here are links to drivers chipset, ethernet and usb3... I don't know where to find the others. There is no equivalent HP PC with motherboard that yours has that I know, who has W7 drivers.
Chipset: The 2nd file on the left is the auto install file.
https://Downloadcenter.Intel.com/download/20775/Intel-chipset-device-software-INF-Update-utility-
USB3: Download, unzip and run the setup.exe file.
Ethernet: 2nd pilot on the list.
-
Win 7 USB controller driver for Pavilion 500 - 217
Hello, I recently spent again PC of my mother to win 8 for Win 7 64 bit. I can't either driver (Intel or AMD) crystallized under drivers available for the controller USB to work. The hardware ID is PCI\VEN_1022 & DEV_7812 & SUBSYS_2AE0103C & REV_03. I also need a driver for the SM Bus controller unless the driver of the usb controller works for both.
I should be grateful if you would help.
Thank you...
Hello:
Install the AMD Chipset Driver and restart. You want to download the chipset 49.7 MB file.
Who should install the two devices.
http://support.AMD.com/en-us/download/chipset?OS=Windows%207%20-%2064
If it does not install the USB 3 controllers, please install both of these drivers.
-
HP Pavilion dv6-7010us laptop PC USB controller driver
Hi, I did a clean install of windows 7 HP and I can not find the driver for the USB controller. Thanks for the help
Hello:
Download and install the drivers for the chipset amd from the link below. You want the first file on the Web page.
http://support.AMD.com/en-us/download/chipset?OS=Windows%207%20-%2064
-
Want to Phoenix 810-430: try to install 256 GB Samsung SSD
Hello I recently purhcased a Phoenix 810 office with a 2 TB drive and I would like to install a 256GB SSD Samsung Pro as OS boot disk and then format 2 TB drive (what I see is a "GPT protected Format") that came with the desktop as a disk storage, deleting the recovery partition. What would be the best way to do this? I know that I can just use the Samsung drive cloning software, but I prefer to do a clean install. I tried to create a set of recovery DVD but for some reason, he did not finish the restoration in the SSD, more it create a recovery partion on that too although I don't want. Can I order a set of HP restore disc that works? I heard also download an iso of 8.1 and Windows with OEM key, which is incorporated in my bios. I was wondering want suggestion or instructions that someone has to do this.
Hello:
I don't know if the tool of creation of media W8.1 I join will work with the product key OEM in the BIOS of your PC, but I don't see that you have nothing to lose by giving it a try.
Download, unzip and run.
Here is the guide to media.
http://Windows.Microsoft.com/en-us/Windows-8/create-reset-refresh-media
-
HP 110-243w downgrade to windows 7 64 bit hp usb controller driver does not work.
I finally got the graphics drivers to work but now can't seem to find the driver for the usb controller. the one on the hp site does not work. work of USB, but I'm assuming that this id for the s 3.0 I have not tested because I have and devices usb 3.o. but he has a! in devie Manager. Thanks in advance.
Hello:
Download and install the AMD chipset drivers and restart. You want the first file on the Web page.
http://support.AMD.com/en-us/download/chipset?OS=Windows%207%20-%2064
If for any reason any USB 3 drivers still don't get installed, then download and install these drivers and reboot.
-
"Unknown device" USB Barcode scanner, problem with the USB controller driver?
Hello
I need assistance with our Barcode Scanners that doesn't work on our newly purchased computers at HP with Windows7 Pro x 64 operating systems.
The brand and model of the bar code scanner is:
Datalogic Heron D130 USB.
When you connect the scanner to a USB port, Windows will try to install this as a HID, but it takes an unusually long time, about 7-8 seconds, to boot the device and install the drivers and appears as an unknown device in windows "devices and printers" and the hand scanner does not work.
Sometimes when you move the USB back can I sometimes the scanner at hand to be recognized as an HID device or a Datalogic barcode scanner,
It works fine until you restart the computer.
After restart the computer cannot detect the scanner Barcode correctly without re - appears as unknown device.
I suspect that there is a compatibility problem between barcode scanner and card USB controller on the computers.
I tried to update all the drivers available on the website www.hp.com and same www.Intel.com (chipset drivers) but nothing has helped to solve this problem
Tried newly bought barcode scanners and "used" barcode scanners earlier who works on other computers, but the problem remains.
I found a workaround by connection of bar codes in a USB hub, and then plug the USB hub to the computer. And leave the USB - hub to take care of the communication with the Barcode Scanner.
in this case, it takes about 2 seconds for the code scanner barcode to mount correctly in windows under the heading "devices and printers" and then works perfectly, even after a reboot.
I googled after a response after my problem, but it seems I'm the only one who experience this issue. ?!
Bought more than 40 computers that I have this problem.
These were bought at different times with two different for suppliers
Computer model are the following
HP ProDesk 1 400 P/N5S21EA
Specifikations:
Does anyone have an idea what could be wrong and how to fix it?
Thanks in advance
Sincerely
Robert T
Hello
The problem is not power - related.
We use passive USB hubs that solves the problemon these computers.
(it also works with the docks, or if you EliteDisplay E241 HP as we thers a usb hub 2 ports inbulit in monitor that works.)
The problem lies in the incompatibility between the Intel USB controller and the hand scanner, can be connected to USB 3.0
When you let another usb-controller support in handshakeing (such as a usb hub), it works.
Datalogic or Intel would like to acknowledge this error.
Because none of the big companies want to acknowledge the problem or repair, personally chose to switch to an AMD platform / CPU instead of the Intel and now it works fine!
We get more performance for your money when AMD is usually less expensive to purchase.
And because of the poor of Datalogic press where they don't even answer e-mail (their only channel for support)
I chose to stop using their products. I'm going to use another provider / brand of barcodescanners.
Maybe you are looking for
-
Re: Portege Z830-11j - SIM not detected
Portege Z830-11j I have this laptop... it's great. However, the supposed right drawer a SIM card is not detectable when it is installed.Is there some lack of software or another installation required. Can anyone help? + Message has been translated.
-
videos of 50i are interpreted as 25i on FCPX
Hello I have a Samsung hmx - t10 cam recorder that shoot Full HD 1080i (50i) When I import the files on Final cut pro X it shows 25i and I don't understand why? I create a new project and add files when exporting am not able to choose 50i (like the s
-
Smart printing is installed but does not work
House smart printing using Windows XP with IE7 is installed with the Bing toolbar. I don't get any errors, but the selection change or allow me to select the element to clip.
-
I installed SP1 today and now it says: «your usb mass storage device can perform faster if it is connected to a hi-speed port...» There are no hi-speed usb host controller installed on this computer... » If sp1 has messed up stuffs on my computer usb
-
Service Pack 2 tries to unplug my graphics card
I installed SP2 for vista x 64 on my PC yesterday. Now I have the symbol in the toolbar disconnect my Radeon 4800 Series(like an usb stick). I'm sure I have shoudn't be able to do this? I uninstalled the ati driver, but it is not solved the problem.