WEI score decreased after upgrading RAM

I am facing a problem with my x 201, I buy 2 to 4 GB of ram for it, but I evaluate the windows experience index, my brand in the form of drop of 6.7 to 3.7 processor also mark the fall of 6.7 to 5.4 too.the config my machine ram is i3 380 m, 8 GB, 320 gb (7200 RPM) WHY? can someone tell me?

Note from Moderator: Edition subject to the content of the game.

Ignore the windows experience index. It's good for a sense of the things database, but it is not extremely precise.

find a program real benchmarking. Run it and see what it tells you.

I use Benchmarking of Lavalys Everest, but it's up to you.

Oh, and if you really with 8 GB of RAM installed, chances are that your processor might have difficulty reading through it as fast he would 4 GB of Ram. This additional load to the reading of the memory would also produce lower CPU score that you have seen. I do not think, he would spend that much, but who knows.

But still, WEI is not correct when you enter the high preformance and large memory capacity.

Oh, and did you buy strips capable RAM DDR3 1066 Mhz, right? If you have purchased DDR2 sticks, they will still work, but they will slow you down.

Can also check on your memory Bus frequency in the BIOS you. the bios on my office sometimes unfolds when I install the new memory, and defaults to a "safe" frequency on the x 201, I'm sure it's 1066 or 1333 Mhz, depending on which set of Bell-and-Whistle you bought. Don't take my word for it. Check with support from lenovo and in your documentation before screwing with your BIOS.

Tags: Lenovo Products

Similar Questions

  • Why Windows Aero does not work after upgrade RAM?

    After that I recently updated my computer desk with 2 new modules 1 GB DDR PC3200 400 mhz 184pin RAM

    PROBLEMS:
    * Windows Aero stopped working.
    * Windows recognizes only 3.5 GB of RAM on 4.
    * Windows Experience Index will not refresh the WEI Score.
    Any help with this?
    I'm back to the old RAM modules and all is well, but whenever I update the last two RAM modules, these errors occur.

    MY RIG:
    OS: Windows 7 Ultimate.
    SR1830NX Compaq
    Max supported RAM: 4 GB PC3200 400 Mhz 184pin DDR (4 Slots of 1 GB each)
    Configuration of the RAM before upgrading (physical)
    SLOT 1: 1 GB
    SLOT 2: 1 GB
    SLOT 3: 512 MB
    SLOT 4: 512 MB
    (although she had 3 GB installed, only 2.5 were recognized).
    Configuration of the RAM after upgrading (physical)
    Slots 1-4: 1 GB each
    Configuration of the BIOS:
    Slot SCHEDULES 1,2 & 4: 1 GB in each slot
    SLOT 3: 512 MB (even if it has 1 GB installed in this slot)

    You seem to have a hardware failure with slot 3. See if there is an update to the BIOS of your card mother, but don't hold your breath. There may not be one and he will probably not correct the problem if there is.

    There is always to be small amount of RAM allocated to the system. Integrated video will be stick like a leech some as well as the network interface card. It's normal, regardless of the version of the installed operating system bit...

  • Satellite A660 - 10 X - no boot after upgrading RAM 8 GB, but 4 GB + 2 GB only

    Hello

    Today I bought two sticks of Kingston 4 GB DDR3 1066 MHz CL7 and I'm trying to replace my 2 GB ones, but something is wrong.

    If I put two sticks of 4 GB laptop does not start. I have the latest version of the BIOS (1.80). I have restored the default settings after upgrade.

    But it's quite strange, because if I put a strip of 4 GB and a 2 GB stick system starts and everything is fine (with memtest86 + too). But there is still one thing: 4 GB stick should be rolled in the dock before, above second, 2 GB module. If I reverse cell phone memory will not start again.

    Is - everyone knows how to solve my problem? Is this a BIOS problem? BIOS version which A660 takes in charge the amount of 8 GB of RAM with no problems? I can downgrade from the BIOS, because I don't know if Toshiba help update.

    Thanks in advance.

    Is this exact module the same 4 GB RAM listed on THIS page?

  • HP all-in - One PC 19-2113w 19: white/black screen after upgrading RAM

    Hello

    So I have upgraded RAM using 2 x 4 GB SODIMM DDR3 Corsair 1600 Mhz, after installing the PC boots but screen is white/black

    steps to follow:

    1. I tried with 1 socket by using only a RAM, screen black

    2. I tried with 2 socket using RAM only one with the same RAM step 1, screen black

    3. I tried step 1 and 2 using the other RAM, screen black

    now here it gets interesting

    4 tried 1 socket using Original/factory RAM, screen black

    5 tried 2 socket using Original/factory RAM, screen black

    6. tried without any RAM at all, looks like a lack of RAM, screen black

    Now, to each measure adopted, I must say that the screen sound not only not showing things, but its totally black as it does at all, until the system starts normally. !

    Is it Possible the upgrade of RAM affect the screen? or maybe when I was replacing the RAM I hit some conecting by cable to screen or something?

    HP 19 all-in-ONE PC

    Product No.G4B06AA #ABA

    Model n ° 19-2113w

    10 64-bit Windows

    Update

    Removed the battery and hold the power for 30 sec button (BIOS reset if I'm not mistaken?) now it works with the orginal of RAM so I guess my new RAM that's the problem!

  • How upgrade to 64 bit Win 7 after upgrade Ram 6 GB on 3250br Pavilion DM1?

    I m going to upgrade 6 GB memory on my Pavilion DM1 3250br. Although windows indicate it is 64-bit capable windows anytime update installed 32-bit (because it has less than 2 GB available).

    1. How should you proceed to upgrade to 64-bit after upgrade memory? I don't have a system disk, only the suplyed key home premium by HP.

    2 HP has 64-bit for all devices drivers? They are in D: recovery drive or I´ll need to download the upgrade?

    3. any information you want to give.

    Best regards

    Eduardo

    Hi, Eduardo:

    You can try it.

    I know it works if you have a retail upgrade key which means that it is good for 32 or 64 bit.

    I don't know an ISO file that you get off the internet is an OEM file.

    If this is the case, it will not work. If this isn't the case, I doubt it will be.

    I have dealt only with the installations of Windows 7 using OEM disks or retail upgrade.

    Basically, the key that you use must be the same as the installation disc.

    OEM disc / ISO good with the key on the bottom of your portable forest 32 or 64 OEM.

    Plenty of retail disc / ISO only good with the full commercial product key, you get the box or the e-mail sent to you - 32 or 64 bit.

    The retail upgrade disc / ISO only good with the retail upgrade key, you get in the box or the e-mail sent to you - 32 or 64-bit.

    Upgrade Express disc / ISO only good with the upgrade retail or upgrade Express key - 32 or 64-bit if you have a disk.

    I used a disk of 64 bit Vista Business anytime upgrade to upgrade Vista Home Premium 64 bit update, and I was able to use the key from Vista Business 32 bit provided with the 32-bit disk (I had a 32-bit Vista Business retail box update but they come only with discs of 32 bits at the time and you had to order a CD of) 64-bit and pay $10. You can't even not the disks in 64-bit vista to MS.

    Hope this helps,

    Paul

    Paul

  • Satellite Pro A120 (PSAC0E) does not start after upgrading RAM

    Hello

    I hope someone can help me here, I recently bought a Satellite Pro A120 (PSAC0E) and decided to upgrade the RAM. I bought a stick of 512 MB of curries with the following specifications: DDR PC2700 200-pin 333 Mhz SODIMM (64 x 64).

    However, the first problem I encountered was an alignment problem. A little effort and handling solved this, but after you insert the RAM into the available slot, the computer laptop wouldn't boot, and instead, I had the flashing sequence on the LED from 2,3,3.

    I was told it might be a problem matching, then tried to remove the original RAM and booting with just the new stick, still the same error. I tried it in the slots and still no joy. It starts very well with the original 256 MB of RAM, but refuses to take the new RAM.

    Are there any known issues? Can anyone suggest something that I can do wrong? I followed the usual steps of upgrade to remove all power cables and the battery before the upgrade, but still no joy.

    Hoping that someone is able to help!

    Hi James

    You simply have bad memory modules and is not a compatible uses.

    > the first problem I encountered was an alignment problem. A little effort and handling solved this,

    This should not happen! The right modules can be inserted without any problem of alignment!
    Handling can damage the module!

    In my opinion, you should use another and supported the RAM module.

    To my knowledge, you can use the PA3512U-1M1G (DDR2-667 1 GB Memory Kit) or (PA3411U-2M1G) DDR2-533 1 GB
    The two should be compatible.

  • Pavilion dv6-3225dx: laptop fails to boot after upgrading RAM.

    Hello

    Recently, I tried upgrading my laptop RAM 8 GB which is max you may have to wait. The RAM sticks were (x 2) DDR3 4 GB Samsung 1600 12800 mhz 1.35v. The system has detected the new RAM, showed the new memory and even spent the memory test. But this isn't the windows startup. I tried to clear CMOS. But without success. Do not let me windows. BIOS version is up to date (F29). Is there any setting for this?

    Thanks for all the help!

    Hello:

    Please see this discussion.  It must be very picky about what memory you use in your model series...

    http://h30434.www3.HP.com/T5/notebook-hardware-and-upgrade-questions/Pavilion-DV6-Windows-10-wont-boot-after-memory-upgrade-4Gb/m-p/5776161#M359223

  • [DV6-3140SL] Problem in my laptop after upgrading RAM

    Hi all,

    I want to upgrade the memory of my laptop HP DV6-3140SL model.

    Original RAM installed is a Micron 16JSF51264HZ-1G4D1, size 4GB.

    Then I bought 2 modules of the model Corsair CMSO4GX3M1A1333C9 (4 GB x 2 = 8 GB total)

    but when I installed this 2 cylinders in my notebook, start windows crashes;

    Sometimes I see Loading icon of progress, but immediately laptop restarts.

    BIOS recognizes correctly 8 GB and memory (the utility in the BIOS) test is OK.

    CMSO4GX3M1A1333C9 should has the same features as the original model of 16JSF51264HZ-1G4D1:

    SODIMM DDR3 PC3-10600 (1333 Mhz)

    What could be the problem? Incompatibility? Or faulty RAM memory?

    Note: NA is 8 64-bit Windows (W8 is an upgrade to Windows 7 original)

    Thank you for the support.

    Paolo.

    paolo220177 wrote:

    Hi all,

    I want to upgrade the memory of my laptop HP DV6-3140SL model.

    Original RAM installed is a Micron 16JSF51264HZ-1G4D1, size 4GB.

    Then I bought 2 modules of the model Corsair CMSO4GX3M1A1333C9 (4 GB x 2 = 8 GB total)

    but when I installed this 2 cylinders in my notebook, start windows crashes;

    Sometimes I see Loading icon of progress, but immediately laptop restarts.

    BIOS recognizes correctly 8 GB and memory (the utility in the BIOS) test is OK.

    CMSO4GX3M1A1333C9 should has the same features as the original model of 16JSF51264HZ-1G4D1:

    SODIMM DDR3 PC3-10600 (1333 Mhz)

    What could be the problem? Incompatibility? Or faulty RAM memory? Incompatible memory modules

    Note: NA is 8 64-bit Windows (W8 is an upgrade to Windows 7 original)

    Thank you for the support.

    Paolo.

    You must use the Configurator of Corsair compatibility on their Web site.

    See if you can return the modules. The modules seen in the image below are the only guaranteed compatible modules by Corsair. Unfortunately, they are not modules of 4 GB compatible to your laptop.

    Memory of Kingston, on the other hand, is it guaranteed compatible 2 GB and 4 GB modules of memory for your laptop. With Kingston, bars of memory, you can upgrade to 8 GB and do work correctly the first time you start it back up after the upgrade.

  • Satellite P200D-130 does not start after upgrading RAM

    Hi, I just upgraded the RAM on my P200D 130 but it does not start after that.
    I removed the 2 Hynix 1 GB PC2-5200 and put in 2 SO Kingston DDR2 2 GB PC667 (should be the same as PC2-5200).
    Post-market nothing happens, light power control is turned on, I him stays CD drive but screen black, no beeps.

    I put one of the 1 GB modules, it starts normally, then I tried a 1 GB into the lower slot module and a 2 GB module in the top slot and it works.
    I tried a single 2 GB module in each slot, even in the form of 2 2 GB modules.

    What could be the reason, better: what would be the solution to ensure that the modules of 2 x 2 GB to work?

    Thanks in advance,

    Michael

    Hello!

    I think that both modules are not compatible to the laptop.
    Normally you can upgrade your laptop to 4 GB. Look in the user manual.

    The RAM, you should bring the computer dealer and request a new one. More buy modules with the same specifications and dimensions. Try buying RAM with the same specs as before.

    Good bye

  • Satellite A110-260 does not work after upgrading RAM

    A110-260 - 512 MB Ram - 533 MHZ - 100 GB - BIOS V1.20 (2 years)

    Hello

    My first attempt to upgrade my RAM has failed.
    After correct installation of the 2 Kingston 1 GB of Ram (Typ: 2,800/1 GB SO-Dimm DDR 2 NMR), my laptop has not started yet, only 5 short sounds (in the owner's Manual: not the duty extended memory).

    Trinkets: 1 Kingston 1 GB - Ram mixed with original Toshiba 512 MB - Ram, Notepad starts, but reached only 896 MB of memory. Performance not signifikant better.

    Who can help me?

    Andi11

    Hello

    I think that simply there is a compatibility problem between the memory modules.
    5 short beeps that appear during POST is a common signal that appears if an error has been detected.

    I think you simply test the different memory modules.

    Big names

  • DV6 - 2150ca does not start after upgrading RAM

    I have HP dv6 - 2150ca with Windows 7 Home Premium 64-bit.

    I had 4 GB of RAM.

    I move to 8 GB of RAM. Both from the same manufacturer and purchased at the same time.

    RAM card

    http://www.crucial.com/upgrade/HP+-+Compaq-memory/Pavilion+DV6+series/Pavilion+DV6-2150us-upgrades.h...

    When I run laplop it says "due to the recent change in hardware or software, windows cannot start... »

    And offer 2 options 1. Repair (recommended) launch utility 2. Start windows normally

    I tried both options, but it came on the screen even after some time.

    I tried with a single chip of all, but it shows a blue screen with error messages

    One last thing, on the slots in laptop RAM 1.5 V is written. I don't know if this is important here.

    I installed old memory, everything is perfect.

    Please advice.

    Yes.

  • Windows 7 Home Premium x 64: activation of the service Windows Update crashes my computer after upgrade RAM

    A few days ago I had two sticks of 2 GB GSkill RAM by mail. Here's the same brand, model and size as the pair currently installed (obviously). (Sticks alternate according to the specifications of the card from my mother)

    After you have installed the new RAM and the computer starts up, it freezes within about 30 seconds of connection. Before installing the new sticks, I had no problem whatsoever.

    My first thought is that I sit the RAM properly, then I go and reinstall it. I start, and the same thing happens.

    So obviously this RAM must be bad, right? When I take out news, not gel. Ah, but when I remove the OLD stuff and use new instead, I ALSO no gel. So maybe it is not the RAM.

    Then I reboot in safe mode. No gel. Interesting. I opened the window 'System' and it says "memory (RAM) installed: 4.00 GB ', which is correct." I opened CPU - Z, and it reports also 4 GB of memory. I run a few hours and have no problems whatsoever. So I say to myself, there must be either a Windows service or a 3rd party service is causing the issue and not the new RAM.

    I disable all services of 3rd parties and restart in normal mode. It freezes. OK, so maybe (though unlikely) I have a virus any (I say probably not because I have to) run the module additional firefox NoScript, and set to block all flash, javascript, xss, iframes, etc. - in other words, only allow to my whitelist and B) I have Windows Firewall and running McAffee and updated.). But I decided to first try Windows services for the hell of it.

    So I enable only the services that start in safe mode as my reference, disabling the rest via services.msc. I start normally and not gel. Great, then maybe it is a Windows service. I start which allows one service after another without any problem. I get to the bottom of the list and select the Windows Update service. Within literally 10 seconds my computer crashes. Large.

    As a validation test, I put all services back to the base line of safe mode and only allow Windows Update. I start normally, and again once it freezes.

    Another test of validation, I start with all normal, but disable Windows Update. Do not freeze. I'm going to start Windows Update. Yet once, it freezes for about 10 seconds. So clearly something is in place.

    As a third and final sanity check, I remove the new RAM and run a Windows Update. He finds a few optional updates, but not critical. My system is up2date.

    My only attempt to solve this problem so far was to backup all Windows Update DLLs (C:\windows\system32\wu*.dll, although I don't know if these are good) and do a scan sfc to replace them with copies of 'good '. It did not work.

    So my question is:

    Why cares Windows Update that I have 4 GB of memory installed?

    Thank you

    Jon

    1. I 'upgraded' from the RC of Windows 7 x 64 for Win 7 x 64 Home Premium.

    2. I use McAfee VirusScan Enterprise 8.7.0i, DAT version 6060, Scan Engine 5400.1158

    3 No.

    4. No, I put together this computer myself.

    ______________________

    To answer my previous posts:

    I think the USB storage is a separate issue. And.

    I think I * may * have solved the problem of origin with one or more of the following (don't know who):

    • Updated the software of the chipset of the card from my mother.
    • Updated HD Windows audio drivers to the recommended ASUS (Realtek) HD audio drivers
    • Updated since Windows installed NVIDIA display drivers for version NVIDIA WHQL.
    • Increased my tRFC (refresh time of line) to 70 52 clocks clocks. Set my GSKILL DRAM voltage recommended by 2.1V. Off the SPD DRAM configuration (I read that ASUS is not entirely based on the SPD and can affect things on its own).

    I had WU for 20 minutes from writing this post without a freeze, so we'll see. (Previously, it would freeze within 10 seconds of turning on WU)

  • Problem on Windows after upgrading RAM

    I have 6 years, Alienware m11x R.2 running Windows 7 x 64 SP1. Since the ole ' computer is still alive and kickin. I thought I'd do a quick refresher on the RAM for an inexpensive upgrade.

    I'm not an expert but to build my own PC and was demolished and rebuilt this laptop particular (among others) several times. The upgrade of RAM has always been something that requires very little attention or other planning that by ensuring that you have compatible specifications.

    I upgraded the RAM this laptop came with a year after the purchase of a Kingston Hyper-X. www.newegg.com/.../Product.aspx

    I remember having no problem with the installation of this RAM and it was perfectly fine since then.

    A few weeks ago, I ordered the DDR3L RAM, after starting the computer difficulties, I realized the error, but also said that the RAM must remain compatible with 1.5V power outlets. But maybe it was a compatibility problem, so I returned it regularly DDR3 RAM, shown here. http://www.Newegg.com/product/product.aspx?item=N82E16820231582

    Outside the actual size of RAM I don't see any other difference with specifications.

    Here's the problem: when I install the new RAM I asked to do a startup repair. No matter if I select run repair or normally I get sent to windows startup. This repeatedly. When I re - install the old RAM is the same screen, but I'm able to start or I can choose to run the repair. (I did both.) This happens with DDR3 and DDR3L RAM. No difference.

    I have triple checked that the RAM is installed correctly and BIOS sees all the 16 gb.

    Advice and assistance is appreciated. Thank you.

    For M11x R2, 8G (2 X 4).

  • Portege 4010 - after upgrading RAM, nothing happens

    Hello
    A beginner very believed in that.

    I picked up some 512 MB PC133 SDRAM for my 4010 but when I put them in the slots and pressing the power button... Nothing happened.

    Would appreciate any help at all...

    Hello!

    Yes, maybe 2 x 128 MB modules were the original modules, that they were delivered with the laptop.

    I think you should try other modules. If you use the modules of noname, they could be possibly not work or problems as bluescreens etc.
    As far as I know that the Portege 4010 can be upgraded to 1 GB of RAM. You can use two 512 MB modules then you should buy RAM from Kingston of high quality for example.

    Here is the part number for Toshiba for a 512 MB module I founded with Google:
    PA3108U - 1 M 51

    Good bye

  • BSOD after upgrade RAM on Satellite L350-14F

    Hello

    I have a L350-14F and I upgraded my ram 2x2gb PC5300 - 667 mHz
    When I start the laptop in bios I see ram 4096 but when I restart the laptop I have a blue screen.

    PFN_LIST_CORRUPT

    STOP: 0x0000004E (0x0000008D, 0x00090ET2, 0x00000000, 0x00000000)

    Windows vista 32-bit sp2 French
    BIOS 1.5

    Hello

    In my opinion the new RAM modules are not ok.
    Maybe the Rams are defective or not fully compatible.

    I use the modules of Kingston RAM. In my opinion it really of goo brand and I neve had problems using these modules.

Maybe you are looking for