What does "Not connected DatabaseAccessor" mean?

Similar Questions

• VPN does not connect in some places

  I have a laptop running v5 Cisco VPN Client that connects to the office of some places network fine, but not other places.  and in the places where it does not connect, it connects fine to another unrelated network.  by "does not connect", I mean that I can't access any of the resources on the office network - the client software seems to work, but there is no access, I cannot ping anything on the office network.  What would cause this?  Here is the log file from a location where it does not connect to the office network:

  Cisco Systems VPN Client 5.0.07.0290 Version
  Copyright (C) 1998-2010 Cisco Systems, Inc.. All rights reserved.
  Customer type: Windows, Windows NT
  Running: 6.1.7600
  Directory of config files: E:\Cisco systems VPN Client\

  1 21:36:30.625 07/03/11 Sev = WARNING/2 CVPND/0xE3400013
  AddRoute cannot add a route which the metric is 0: code 160
  Destination 5.0.0.0
  Subnet mask 255.0.0.0
  Gateway 192.36.253.1
  Interface 192.36.253.179

  2 21:36:30.625 07/03/11 Sev = WARNING/2 CM/0xA3100024
  Failed to add the route. Network: 5000000, subnet mask: ff000000, Interface: c024fdb3 Gateway: c024fd01.

  in this particular case, the local network uses the range of 192.168.1.x IP addresses, so that shouldn't be a problem.

  Lee

  Could you go through a PAT instrument, so you are not able to access resources after the VPN is connected because ESP packets usually will not go through a PAT tool.

  What must be configured on the VPN server is to allow NAT - t (NAT Traversal), IE: encapsulation of the ESP package in UDP or TCP packet, then it passes through PAT instrument very well.

  What server VPN should you terminate the VPN Client?

  The command to activate on the SAA would be: crypto isakmp nat-traversal 20

  Let me know if you have other devices like the VPN server.

  Hope that helps.

• HP Deskjet 3055 A does not connect to the WIFI with security

  I'm trying to configure a Deskjet 3055 A on my DD - WRT router.  I am a highly qualified network engineer, so I don't know 100% what I'm doing.

  First, DD - WRT supports WPS connection, because these are very precarious.  This means that my only way to connect the pritner to my home network is to connect to my PC and use the Setup utility (downloaded from your page drivers) I use the 28.8 version.

  My router supports the 2.4 and 5 GHz and I know the printer is only 2.4 GHz.  I disabled completely the 5 GHz network in order to connect the printer, even though it shouldn't have any effect.

  I restarted my router and reset the printers wireless network using its integrated control panel.

  In any case, after a shameful 2 hours troubleshooting, I did discover that the printer WILL NOT CONNECT to the WIFI network if any security is applied against it.  It works 100% fine with open security however, it is totally unacceptable.

  I tried both WPA Personal and WPA2 Personal, both with the same effect.

  For reasons to try, I added also the printer to my network WIFI open and tried to manually change the setting WIFI via webinterface of printers, however, whenever I try and access the wireless configuration wizard, I simply get an error message saying "Internal system error" - eventually I managed to work around this another bug that has been there for years (see http://h30434.www3.hp.com/t5/Printer-Networking-and-Wireless/Internal-System-Error-prevents-access-t...

  After installing printers web interface WIFI, the problem is always the same and it does not connect.

  HP, we were in the order of 2500 of these printers for users of our remote site.  If you don't come to the top with a quick solution/bug fixed, consider the lost business!

  Concerning

  Ian

  After playing well, I managed to find a solution for this!

  For all users who are unable to find a solution by using the other methods, here's what to do.

  Change your local network to open the safe but note your WIFI settings for your default installation.

  Connect the printer to the open network the HP software (via USB cable)

  Go to the URL of the printer, but make sure that you connect through HTTPS - if you get an internal system error, keep refreshing until it works (WHAT A JOKE!)

  Click on 'Network', then click 'Advanced' on the left.

  Enter the network settings as they need to be secured.

  Downstairs, check "in an infrastructure network, use 802. 11b / g behavior (assuming that your assisted supports g, otherwise use the b only option), then click on apply.

  Turn on your wireless security, on your router and then the printer should connect!

  I am really confused as to why this is not automatically enabled, if the printer is not working with security on a Wireless N network wireless, then have this as the default!

  HP - feel free to thank me in this post!

• My new iPod does not connect to my 2006 iMac G5 - how to download all my music iTunes (mainly CDs) on my iPod. ?

  MY new iPod does not connect to my 2006 G5 iMac. How can I download my iTunes (music mainly from my own CD) library on my new iPod. My iMac works well, but running an ancient operating system that does not seem to be updated capable?

  This is not possible.  I don't know what specific iPod model you have, but any new iPod does not work with a Mac running Mac OS X 10.4.11 (and support older version of iTunes).

  There are more older models iPod work (you can buy used) and many of them, in my opinion, have GREAT sound quality.  To playback audio, new does not mean better.

• I've set up another configuration of TCP/IP, but it does not connect. I need to access the 3 different machine networks. Any ideas?

  I've set up another configuration of TCP/IP, but it does not connect. I need to access the 3 different machine networks. Any ideas?

  original title: alternate tcp/ip

  If by "alternate TCP/IP configuration" you mean the settings on this screen--> http://tinyurl.com/42kbqqz, then, to quote Inigo Montoya, "you keep using that Word. I don't think it means what you think it means. »

  The 'alternative' configuration settings tab, if you select "IP address private auto" (APIPA) or "specified user" is only used IF "obtain an IP address automatically" is set on the tab 'General' (http://tinyurl.com/8p9hn) AND the adapter cannot get an IP from a DHCP server.

  Most cable networks use a DHCP server to automatically assign IP addresses.  In this case, just plug your Ethernet cable and you're automatically configured and connected.

  If the problem is that your network requires a static IP address (that is, they use a DHCP server to automatically assign IP addresses), you will need a third-party network settings manager.  If you have an IBM (Lenovo) ThinkPad, you can use "Dial-up connections." IBM Otherwise, see this Google search (I have no experience with any of the applications shown, so I can't comment about them): http://www.google.com/#sclient=psy&hl=en&source=hp&q=network+configuration+switcher&pbx=1&oq=network+configuration+switcher&aq=f&aqi=g-v5&aql=&gs_sm=e&gs_upl=23l1333l1l1599l12l8l0l0l0l5l278l1344l0.7.1l8l0&bav=on.2,or.r_gc.r_pw.&fp=74e371c96a48f4b&biw=1024&bih=649

• New Windows 7 Asus computer laptop does not connect to internet

  ASUS A52JR - X 1 laptop computer

  He'll find a network.  It doesn't let me access the network files.  It does not connect to the internet, but it's getting an IP address.  DNS does not, even if it has the IP of the router listed as a DNS server.

  I disabled IPv6 based on other peoples problems, but it doesn't seem to help.  I tried to update the driver for the CARD, but it doesn't seem to help.   I'll try update driver video, to see if it helped, but the pilot was not available on the main site (Radeon 5470) and I don't know how it would be useful anyway.

  Diagnose Windows said try restarting the router, which I did, but it did not help.  If I skip this step, said diagnosis "the default gateway is not available."

  There is also a tunnel of the card, even after disabling IPv6.  I don't know if this is normal or not.

  Any help would be appreciated.

  What router are you using? You can turn off proxy DNS? If this is not
  possible, you should be able to get the IP addresses of the DNS servers of your ISP
  and configure those statically. The use of routers IP means that the router is
  Proxy DNS. Looks like proxy DNS does not work.
   
  On Wednesday, may 5, 2010 14:31:07 + 0000, Tedsternator wrote:
   
  > ASUS A52JR - X 1 laptop
  >
  > It will find a network. It doesn't let me access the network files. It does not connect to the internet, but it's getting an IP address. DNS does not, even if it has the IP of the router listed as a DNS server.
  >
  > I disabled IPv6 based on other peoples problems, but it doesn't seem to help. I tried to update the driver for the CARD, but it doesn't seem to help. I'll try update driver video, to see if it helped, but the pilot was not available on the main site (Radeon 5470) and I don't know how it would be useful anyway.
  >
  > Diagnose Windows said try restarting the router, which I did, but it did not help. If I skip this step, said diagnosis "the default gateway is not available."
  >
  > There is also a tunnel of the card, even after disabling IPv6. I don't know if this is normal or not.
  >
  > Any help would be appreciated.
   

  Barb Bowman www.digitalmediaphile.com

• Dreamweaver (CC) does not connect to internet

  My copy of Dreamweaver CC does not connect to the internet. For example, when I go to help > Help and Support > Dreamweaver online help, I get the error message "unable to display help. Connect to the internet, and then try again. "For more information, see http://www.adobe.com/go/offline_help" (i.e. instructions on the use of the PDF file helps to document, not particularly to this situation)

  (This is probably obvious because I have write in a forum, but the computer and all the other programs on it have no problem connecting to the internet).

  I did a complete uninstall/reinstall, using the tool to clean up following the instructions here and CC: use of the Adobe Creative Cloud cleaning tool to solve installation problems

  I followed all the instructions here: Solutions to connect, activation and errors in connection with creative cloud and Creative Suite applications

  None of the steps show a problem, but I can't always connect.

  What can I do else?

  
  

  Details:

  
  Adobe Dreamweaver CC

  2015.1 release

  7851 build

  Windows 7 Professional 64-bit

  Please check if you have adobe entries in your HOSTS file, if there is no entry in it, which means Adobe is getting stuck on your machine.

  See SOLUTION 3 in the following document to check and fix the HOSTS file: applications of Adobe Creative Cloud reverts after 2015 updated CC test

• My UK 6s iPhone does not connect to the network in Germany?

  My UK 6s iPhone does not connect to the network in Germany?

  'The network '? Which network? WiFi or cell phone? And what have you already tried to get connected?

• After that put 36.0.1 to date, does not connect to internet

  After update, don't be loading not pages. Does not connect to Comcast. Computer restarted from scratch, reset modem and router - nothing works. I tried Safe Mode early, did not work. Internet Explorer works fine. Mail works fine.

  There is no error message when the update has been loaded.

  It is a terrible 'update '! How can I fix it?

  IQ140 said

  After update, don't be loading not pages. Does not connect to Comcast. Computer restarted from scratch, reset modem and router - nothing works. I tried Safe Mode early, did not work. Internet Explorer works fine. Mail works fine.

  There is no error message when the update has been loaded.

  It is a terrible 'update '! How can I fix it?

  Update: I indeed found firewall was the issue (the first time with updates of Firefox). I tried uninstalling and reinstalling, but that no longer works.
  Then I opened the application window of Norton Security (looking for information of firewall). I don't actually change or click on what to Norton. I decided to try to install again. This time, when I hit "Run" instead of "Save", the small window Norton popped up saying downloading is safe. Then he installed and opens very well.

  It may be a quirk of Norton? Or by choosing run rather than save (and running after registration)?

• Firefox does not connect to any Web site, but other browsers will.

  When I get something in the URL- google.com, localhost, http://127.0.0.1/ one bar the IP address, there is a fraction of a second flash, then the bar becomes empty and nothing has changed. It seems that Firefox is not even try to connect to the internet.

  Yesterday, everything was fine when I was running FF on Windows 7. After the upgrade to Windows Pro 8, Firefox has failed. I've updated for Windows 8.1, hoping for the best, but it's the same problem.

  I've walked by the firewall program, several times (the only race is the built-in Windows Firewall). Finally, I uninstalled Firefox, including all my settings, custom and reinstalled from scratch, twice. And even this version pure and clean Firefox does not connect to the internet.

  I am a computer web developer and would be happy to look at the log files or run a tool (Fiddler?) to see what happens at a low level, if I only knew where to look.

  john99, thanks for the links. I went through all (again), one by one. The last link kb.mozillazine.org/Standard_diagnostic showed me what helped. I've renamed "firefox.exe" to "firefox1.exe" and was able to use firefox.

  It made me suspect the firewall or malicious software. I ran a Malwarebytes full scan, zero problems detected. I have pored on the entries of windows firewall, the "Windows Firewall with advanced security" view and also the simple control panel view. The only mention of Firefox is that I continue to add and remove to allow firefox through.

  Here I knew what was going on, but for now, I can at least use firefox. How frustrating!

• iPad does not connect to the Wifi on the range 192.168.0. *.

  I have an iPad Mini (ME860BA) on os 9.3.1 that would not connect to my wifi at home.  He began to abandon their studies repeatedly a few months before and then just wouldn't connect at all.  It is on the os 9.3 so I upgraded to 9.3.1 but it did not help.  I was able to connect using a hotspot from my phone but no go on the real wifi. Sometimes it seems impossible to connect and others it seems to connect but without the wifi icon that appear (and internet access). All other devices connect to the House without exception (or question) - it's just my iPad.

  I followed every bit of advice I've found - turning wifi off & on, forgetting network, reset all the network settings, hard reboot, reboot normal, turning airplane mode turn off again, go up the brightness of the screen (odd) and finally I restored my router and the iPad to factory settings.  Nothing worked, so I took him to a store of Apple and waiting for the genius to see me I thought I would try to connect to the wifi and it went all right!  I felt a little silly to start with but they still took a look and said that he had 'something' bad, but they didn't know what.  Their best guess was that it was something to do with password authentication because they are client wifi has no password.  I returned home and disabled the security mode of the router - I have a Virgin Superhub running the 2.4 and 5 GHz primary wireless networks - no amount of adjusting the security modes (remove the password, make visible SSID, change of Protocol) makes all the difference.  However, knowing that it worked on wifi from Apple in the store, I was really puzzled.

  After ages bother with different parameters (especially in my router), I now know why it does not connect to home... My Virgin router to short on a range of address DHCP IP of 192.168. 0. * and my iPad suddenly won't connect unless the beach is 192.168. 1. * or higher.  (It connected OK for 2 years).  It took weeks to find this out, but at least now I can connect.  I turned on the wifi of comments because it uses the gamme.1.  Everything is good, connects the first time, every time!  I have not tried establishing a password (I was so happy, it connected I left because it was... well as I switch on the MAC filtering, for a little extra protection) I could try side password later and if it still connect, I'll update my post.

  My solution is very well when I'm at home but is not going to help if I get the iPad with me - it will be hit & miss if I can get the WiFi also.  Must be set correctly - I see no that it is hardware related, so there must be a bug in the software/firmware.

  Anyone having problems connecting to wifi can try the workaround network comments - at least it will get you.

  Is there a future fix for this?

  Re: iPad wifi suddenly does not save

  Change the range on the router you want to connect to.

• Ink advantage 2545: changed the name of the wireless router and now ink advantage 2545 does not connect and I'm out of ideas

  I have a Toshiba laptop 64 bit running Windows 10 Home, 8 GB, 1 t hard drive.

  Router is a Samsung phone using Android because it was the only router that I could find which would take the wireless signal.

  I live very pastoral, no neighbours for miles, so I never saw the need for a password on my router.

  Now, some people are installs in less than 400 feet from me, and I think they're piggybacking on my Wifi because my access speed has slowed considerably since they moved in.

  So I decided to change the password of the router, unfortunately, I can not put in any password I want.  It gives me the opportunity to have a predefined password.  So I changed the name of the router I could do without problem.

  My computer very quickly without any problem, however, my printer which worked great for a year with the old router name does not connect on the new name of the router.

  Here is what I tried:

  I had hoped he would ask me for a new name / password, but it did not.

  Then I plugged a cable between the printer and the laptop in the hopes that it would produce a different kind of results.  It has not changed anything.  There is no screen menu on what that be like this on the printer.

  I pressed the wireless button that has the flashing blue light and nothing happened.

  I pressed the button, don't know what it is, but it has a white light, and nothing happened.

  I went on the HP site and followed the instructions but he just said do not connect the cable until told to do so.  So I disconnected everything, lights out and turned back on and still no connection and no invite to plug whatever it is.

  Y at - it everywhere where I have being a novice could get instructions on how to get this working?

  I appreciate any help you can give me.  Thank you.

  Hello

  I think you are talking about SSID. Please, think of it as a new router and use the following ways to correct:

  http://www.HP.com/global/au/en/wireless/reconfiguring-system-Help3.html
  
  Kind regards.

• iPad does not connect to the server

  Kind of, it looks like my iPad has disappeared and twisted his tail (connection) and got lost somewhere in cyberspace.

  Yesterday morning he opens to the screen Hello > Slide Set up who brought up the screen 'could not activate iPad' with the message "your iPad could not be activated because the activation server is not reachable. Try to connect the iPad to iTunes to activate it, or try again in a few minutes. If the problem persists, contact Apple Support at apple.com/support".

  This condition actually began three days when it does not connect to my Airport wireless internet and I could not he deleted.  I made the troubleshooting on the dome using Airport utility that showed connections to the top and the green. My main computer is not affected. I was able to put a return by making a total system power off for a few minutes and then turned on one at a time with the modem (cable) beginning (all equipment - computers, iPad, modem and airport), then the airport, my main computer (2003 iMac screen all-in-one flat) then the dome of the iMac. They are all restored correctly at full speed. At the point where I was interested only in the dome as I was doing some work on it using Classic applications and did not activate the iPad until the most late in the evening.

  I was wondering what is happening and if there is an inexpensive way to get it running again?

  Sparkgapper

  p.s. There is an Apple Store here in El Paso, if it's a long drive where I live.

  If you have problems with the applications of stalling or crashing,

  double click on the "home" button

  -slide up on applications to force leave their

  Re-boot ipad.

  Press on and press and hold the sleep/wake button until a Red slider appears, and then drag the slider. Press and hold the sleep/wake button until the Apple logo appears.

  https://support.Apple.com/en-us/HT201559

  Force power down if above give it trouble you.

  At the same time hold the sleep/wake button and the Home button. Ten seconds or more.  Keep until the Apple logo appears.

  more information on the re-start:

  http://iPad.about.com/od/iPad_Guide/SS/how-to-reboot-your-iPad-power-off.htm

  This these tips from MichelPM to improve performance:

  https://discussions.Apple.com/message/29504169#29504169

  https://discussions.Apple.com/message/29504311#29504311

  Restore factory settings by loading the latest version of the ios that will support your machine:

  (1) make a full backup of your device if necessary.  Is two times better - cloud and computer.

  https://support.Apple.com/en-us/HT203977

  (2) three methods of restoration of your ipad.  [simple as abc]

  2.a) "you can use iTunes to restore your iPhone, iPad or iPod touch to factory settings and the latest version of iOS."

  http://support.Apple.com/kb/HT1414?viewlocale=en_US & local = en_US

  2.b) be a little more insistent: "you can put your device iOS in recovery mode, then restore it via iTunes.:

  http://support.Apple.com/en-us/HT201263

  3.c) as a last resort, you might consider DFU (Device Firmware Update).  This could void your warranty.

  http://www.IMore.com/Tip-put-iPhone-iPad-DFU-mode

• Hall 13: HP pavilion laptop does not connect to the printer HP envy range 7640

  My laptop does not connect to my HP envy printer. It keeps saying the driver is not available or is it ready, but does not connect. I know the printer is working because I can print from my phone. Anyone know the driver I need to download or what to do?

  Ruizgeraldine

  Hello;
  
  Let me welcome you on the HP forums!
  
  I read your post about the problems with your Envy 7640 in Win10 printer and wanted to help.

  The problem is that by default HP print drivers installed by the upgrade of Win10 often do not work.  I have two HP printers and neither one worked after the Win10 upgrade.  We also receive a lot of messages of other people with the same problems.
  
  I linked the page drivers and software for the Win10 drivers for your printer: http://support.hp.com/us-en/drivers/selfservice/hp-envy-7640-e-all-in-one-printer-series/6617267/model/6617268#Z7_3054ICK0K8UDA0AQC11TA930C7

  You must download and install the full feature software and drivers for the printer.
  
  Then unplug the printer and install the software.
  
  Do reconnect the printer until the installation program invited to do so.
  
  Once the installation is complete, restart.
  
  You should then be able to use your printer in Win10.
  
  Good luck
  
  ========================================================================
  I'm a volunteer and I do not work for, or represent, HP.
  ---------------------------------------------------------------
  Please click on 'Accept as Solution' on the post that solves your problem to help others to find the solution.
  Please click on the symbol of the thumbs-up to the left of the answer key to say thanks fopr my help.
  ========================================================================

• Satellite L350 does not connect to the internet, network adapter yellow exclamation

  Trying to help my Nan with his laptop...
  Model is Satellite L350-170

  Does not connect to internet, even using the Ethernet cable. Network cards have yellow exclamation marks on it and seems he needs an updated driver. How the hell can I download and update if it does not connect to the internet. And then, what update is necessary, because I searched on here and there is no update driver for network card?

  She had various internet help from its supplier and a visit at home but still no joy. Internet works fine on other devices. Any advice greatly appreciated.

  All the drivers can be downloaded from the Toshiba UE driver page.
  http://www.Toshiba.EU/innovation/download_drivers_bios.jsp
  Choose your model of laptop in the form of download and the system that is pre-installed on you unit.
  Then, you will get the list of drivers.

  If you are not able to connect to the internet due to lack of driver LAN/WLan, then you another computer for download.

  You asked how to remove the network card?
  Usually, you need to access the Device Manager (in Control Panel) then we need to expand the area to network adapters and you will find the LAN and WLan card.
  Click the single LED adapter, and then press or click on uninstall button driver