What happens with the Mac Pro (end 2013)?

Similar Questions

• My mac pro end 2013 connecto to 3rd monitor used

  I just got a couple of monitors Samsung 4 K and I connected to my Mac Pro model 2013 end that has two graphics cards AMD over-pants D700. I also want to plug a 4 K TV to my installation in order to show the greatest screen previews for customers. I've separated the connections of each monitor in the ports of different buses, as shown in the Apple Web site. Both screens are connected via thunderbolt and the TV is connected via HDMI. The problem is when I plug the TV one of the monitors completely loses the signal. I tried to swap the connections of ports between the two monitors and the TV but the result is the same, the computer will only send the signals of two of the three connected. I would be grateful someone knows how to fix this problem, thanks.

  You said: "the two screens are connected via thunderbolt and the TV is connected via HDMI.".

  You say you have two screens Thunderbolt?

  If this isn't the case, which is entered on the monitors?

  If this isn't the case, entered ui displayport/mini displayport may be both legacy connections (DVI or HDMI). For more than two, you need an adopter active.

  Each device is connected to another bus Thunderbolt?

  See:

  Use multiple screens with your Mac Pro (end 2013) - Apple Support

• What is the situation with the mac pro users and map of cuda for ray-tracing work?

  What is the situation with the mac pro users and map of cuda for ray-tracing work? If it is not necessary or should I try to install a?

  CUDA acceleration is no longer under development, and I've only played with traced to the RADIUS on a few test projects. If I need 3D dimensions objects I used C4D Lite, which is now included in EI

• Using Firefox 4 and Windows 7. Whenever I have to start Firefox from a shortcut to a Web site, what happens with the following error "there was a problem sending the command to the program". The requested site is loaded after that. without any problem.

  Using Firefox 4 and Windows 7. Whenever I have to start Firefox from a shortcut to a Web site, what happens with the following error "there was a problem sending the command to the program". The requested site is loaded after that. without any problem.

  If a shortcut is used while Firefox is already open the error will not occur.

  For me, the problem was the FoxClock extension. Once I disabled it, the problem was gone.

  Hope this helps.

  Olivier

• What happens with the app that I do not install now?

  What happens with the app that I do not install now? It will be available 1 year from the moment I am installing? Because I only need to photoshop and Illustrator now, but next year, I will work with inDesing. I have not yet installed inDesign and wish that, when I install it the next year it will be available 1 year. I bought the cloud creative adobe and I only install Photoshop and Illustrator now.

  Thank you

  In addition:

  Membership begins when you buy instead during installation. All applications are on the same schedule and will expire and renew at the same time.

• Mac Pro (end 2013) is no longer detects the internal SSD flash drive.

  How to fix?  I replaced the drive and the wiring without result. Help!

  MIchael

  I'm confused. Mac Pro end of 2013 desktop computer uses a blade SSD with no wiring.

  It is the Mac pro desktop forum.

  It detects another drive? Maybe an SSD of Baden

• Mac Pro (end 2013) freezing issues

  Hello

  I bought a couple of years a new fantastic Mac Pro, but in a few months I started to think that I made a terrible choice.

  The computer crashes very often since I updated it to El Capitan, but it was difficult to work on Adobe Premiere since the outset: ridiculously slow, three hours to make a 4 minute clip.

  I contacted the Apple store, they kept for a week, they said he went from testing all the equipment and they found nothing wrong.

  The mac is still suspended. SO FRUSTRATING.

  I work on Photoshop, most of the time, but I have the experience of the 'freeze' even just browse the folders with the finder or visit a Web site on Chrome or watch movies. I unplugged all peripheral usb/firewire, mac freezes still. I repaired disk permissions but reports seem ok.

  I started with the Mavericks, I upgraded to Yosemite, El Capitan I reinstalled from scratch.

  But nothing has changed in fact related to the gel issue, once time and then (sometimes up to 8 times a day), I need to force a restart by using the power button, because everything is frozen.

  The trackpad and the graphics tablet (Wacom Pro middle) are frozen, no key is accepted.

  Apple has determined that in some late 2013 Mac Pro graphics cards may cause video problems - without video, system instability, freeze - but it seems that only the GPU AMD OVER-PANTS D500/D700 are affected (I have the base model with a D300).

  Do you have any hint? Is that what I can do to understand what is the problem?

  I wish I could be in a position, at least, to reproduce the problem, but sometimes it takes days between a 'freeze' and the other. Error reports are generated not either, it is one of the error messages Console that I could find:

  WindowServer [176]: GPU Driver seems to be suspended (more than 5 continuous seconds of reluctance)

  I am a professional photographer and work is very unproductive and frustrating. I'm losing money customers time and my mood, and I would like a response from Apple on this topic.

  Looks like it could be due to problem of graphic material.

  have you looked at this long discussions:

  Mac pro end of 2013 freezes with the spinning wheel

• Mac pro (end 2013) forget screens - 6 monitors

  Hello

  I have a 6 monitor Setup, with different resolutions 3 x 1080 p + 2 x 2160 x 1440 p p + 1. On most days things work very well!

  I only put the display to sleep. When I wake up the screens I often lose the position of windows, if anyone has a suggestion would be great, but this isn't why I created this post. My real problem is that lately, with Yosemite, the Mac Pro was forget a monitor or two, as in 4 or 5 of the 6 monitors turning on, it is pretty boring because the only way I found to fix it is to restart (several times), having thus everywhere reconnect.

  System Preferences-> display-> Option + Detect poster tent, but the success

  Monitor Off, then on does not work, same behavior

  * Tent, but without success means that the monitor turns on, says no signal then goes back to the stand-by

  * I had to use the "Mini to Dual-Link DVI adapter DisplayPort' in the light of the 6th monitor, she lit up not otherwise

  On the this Mac-> poster SEES SIX SCREENS

  So, the system sees the monitor, I can move windows, it just does not shine there.

  Is there a technical document somewhere that can help me get out of it?

  Ideas? Things to try? Suggested wiring?

  Suggested wiring?

  Thanks for any help you can give me

  FRANTZCY

  -Additional information:

  Installation program:

  Mac Pro

  3.5 GHz 6-Core Intel Xeon E5

  32 GB OF RAM

  AMD over-pants D700

  1 T HD

  Exhibition:

  ASUS PB287Q:

  Resolution: 3008 x 1692 to 60 Hz

  Sampling: 30 - Bit Color (ARGB2101010)

  Mirror: Off

  Online: Yes

  Rotation: support

  Connection type: DisplayPort

  TV: Yes

  BenQ GL2450H:

  Resolution: 1920 x 1080 @ 60 Hz (1080 p)

  Sampling: 30 - Bit Color (ARGB2101010)

  Display serial number: XXXXXXXX

  Mirror: Off

  Online: Yes

  Rotation: support

  Adapter type: Apple Mini DisplayPort to DVI dual link

  Adapter Firmware Version: 1.03

  TV: Yes

  BenQ GL2450H:

  Resolution: 1920 x 1080 @ 60 Hz (1080 p)

  Sampling: 30 - Bit Color (ARGB2101010)

  Display serial number: XXXXXXXX

  Mirror: Off

  Online: Yes

  Rotation: support

  TV: Yes

  DELL U2711 REFERENCE:

  Resolution: 2560 x 1440 @ 59Hz

  Sampling: 30 - Bit Color (ARGB2101010)

  Display serial number: XXXXXXXX

  Main screen: Yes

  Mirror: Off

  Online: Yes

  Rotation: support

  Connection type: DisplayPort

  TV: Yes

  BenQ GL2450H:

  Resolution: 1920 x 1080 @ 60 Hz (1080 p)

  Sampling: 30 - Bit Color (ARGB2101010)

  Display serial number: XXXXXXXX

  Mirror: Off

  Online: Yes

  Rotation: support

  TV: Yes

  ASUS PB287Q:

  Resolution: 3008 x 1692 to 60 Hz

  Sampling: 30 - Bit Color (ARGB2101010)

  Mirror: Off

  Online: Yes

  Rotation: support

  Connection type: DisplayPort

  TV: Yes

  Hey, I have a guess: your graphics card can't handle so much strong ports HD is what I think. I'm good for Apple computers. Get a new Mac pro graphics card if Apple supports a Mac Pro for.

• connecting the iphone 6 with the Mac Pro for messages

  My iPhone 6 is not bind properly with my Mac Pro for Messages.  When sending a message from the Mac Pro, the message will be displayed on the iPhone immediately, but this is not always appear as "sent" or "delivered" on the Mac; It just shows an incomplete treatment green line at the top of the message on the Mac bar.  This occurs only with SMS messages.

  I followed the instructions to connect the two devices using my Yahoo account, but it still does not work properly.

  Any ideas?

  Make sure that your iPhone software is up-to-date.

  Tap Settings > general > software update

  The latest iOS version is 9.3.4.

• Mac pro (end 2013) in favor 43UH6100 LG

  Hello!

  I have used a 2817 Dell and an old 28 "HD monitor and recently wanted to replace my old HD monitor for a TV from LG UHD 43". I realize that HDMI port on the mac is evaluated only for 3840x2160@30Hz, but for some reason the TV 43UH6100 is detected as "screen LG TV to 120.5 7680 x 4050" when I provides information on the system... to this resolution, it is quite illegible, but with scale I can clean it up a bit. My intention is to run the 3840x2160@30 resolution.

  Any ideas on how to convince the mac pro to offer 3840x2160@30Hz as a resolution possible? I checked the Web from LG site and there is no update firmware to pick up (again)

  Erik

  Try an application like:

  SwitchResX _ resolution Control for Mac

  In order to use SwitchResX with EC see:

  http://www.madrau.com/support/support/srx_1011.html

  The menu of the Mac App Store

  Try changing the EDID

  http://www.InsanelyMac.com/forum/topic/281412-how-to-advanced-EDID-injection/

• What happens with the data on ROW as soon as they are storage migrated to VMDK?

  Hi all

  The following scenario: I have a virtual machine with virtual RDM. I have storage migration online, selection of thick discs so convert the VMDK RDM. The question is: what is actually happening with the data on the LUN that was RDMs, once the migration is complete?

  I expect that the data are still there, and if needed, I can remove the VMDK and re - attach the new LUNS as RDM.. But I can't find any official information on this.

  I am not mistaken? Y at - there somewhere that says clearly what is happening with the data?

  Thank you!

  Your wait is quite correct. The data on the raw LUN will not get affected once it is converted to a virtual machine. Only the mapping of RDM file is deleted and the LUN becomes available, and you can use card or again as an RDM or to create a VMFS data on that store.

  André

• First CC 2014 plays do not clip or timeline with the new Mac Pro end 2013 D700

  I used the cs5 and cs6 first and never had this problem

  I just bought a new mac pro and installed the trial of first cc 2014

  I put my script to import the clips as usual, and the play button does not work

  in the viewer or in the timeline panel.  May seem nothing to operate

  also, I'm on 10.9.5 which I guess should be good.

  Hi Ernie,.

  Try this: create a new user with administrator privileges and see if you can get Premiere Pro for video playback once more.

  Thank you
  Kevin

• Running Mac OS older than what came with the Mac

  I just got the phone with Apple's Support and the representative told me that no Mac will perform a Mac OS older than the one that came with it. Can someone verify or refute this claim? I've been using Macs since I was introduced to a warm SE/30 in 1989, but I never remember to do this.

  So why would I want to? Well, I just bought an iMac 2014 end provided with Yosemite (10.10), to replace an early 2011 MacBook Pro that came with Snow Leopard (10.6). I am a photographer, and I have three dear old Sony sublimation photo printers that I can run only with a software package that has turned into a pumpkin after 10.6, so I have the updated MBP in place like a machine to dual-boot with a small partition of 10.6 for the software and a large partition of El Capitan (10.11) for most of my work. I want to put in place my new iMac in the same way (of course, the upgrade of its large partition to El Capitan); Otherwise, I will need to keep the MBP as a print server. (Or more likely, press an old iMac 2006 with a screen of bad back in service as a headless print server).

  If it is impossible to start in an old Mac OS, are there emulators that could achieve this goal (which might be better - avoiding a reboot)? Sony has been much better update their printer drivers for Windows and Mac, so I could probably run in Windows under an emulator like Parallels or Bootcamp, but I try to avoid dealing with a completely different environment. (Not to mention the fact that two of my Sonys are SCSI machines I drive with FireWire 400/SCSI converter; not to tell how Windows would treat that ;-))  Of course, this alone probably favour the approach of print server, because I do not know how things do you wear with a double conversion (starting with the new iMac USB3 or Thunderbolt and passing by FireWire SCSI. It's all too complicated...

  In a related issue, if I am successful in 10.6 market in some way on a new Mac, could I also run Rosetta? Snow Leopard is the last Mac OS supported under Rosetta PowerPC applications, and I have a still-good condition, fully licensed Adobe Creative Suite Premium (PowerPC) that I want to continue to run and make so much faster that this old iMac (or even my MBP) will be.

  TIA,

  Ken

  1. use Mac OS X Server 10.6 (phone the Apple Online Store) inside a product such as VirtualBox or Parallels Desktop.

  2. Yes.

  (136839)

• What happens with the support of the seller now?

  After a year on the world of BB, my last update of the app was rejected for a mention of a competitor device, including the help, even if this text is in the HelpFile for the app was introduced a year ago. I had several problems with the notice of rejection, too many to describe the limited size of editing area on the assistance of the vendor page, so I asked them to tell me how to send email directly to a more detailed question. About a week later, I got a reply with an email address, so I sent my full question so that I can present my application in full compliance and avoid another rejection. Shortlly after what I read Blackberry pulled about 650 employees of supplier support because they were going to focus on the business space. Since then, I waited about three weeks, without response, and it's more than a month I tried to provide some features improved my users.

  Given the bad news on the Support of the seller, what I want to know now is:

  1. Are there dead ANY provider of support for answering questions of application developers?
  2. If so, what is the waiting period now to get answers.
  3. Blackberry completely abandoned the independent developers now?

  I made the choice in February 2013 to focus exclusively on the development of native applications for Blackberry 10, tie my future to the success of the new operating system. Now, it seems my faith and commitment have been misplaced and I wonder how much longer before the existing applications are left to wither on the vine, because developers are no longer able to fix bugs or add features.

  Hi greenmr,.

  Can you give us a few bits of information specifically regarding your post?

  (1) what email address you send your long list of questions too?

  (2) did you have a case or Incident # assigned to enamel (usually contained in the subject line of an answer or an automatic response)?

  To answer your question, yes there are still people working on BlackBerry World and in particular, support for the seller.

• What happens with the Dehaze adjustments during the transition from CC LR6?

  Hello

  I use LR CC for a year, but for my personal use (do not use PS at all), it is not sensible to continue in this way.

  I would switch to LR6, which does not include the cursor "Dehaze."

  What happens to my catalogue after this switch?

  The pictures that I have already edited will be even more "washed out / misty", or that they will keep their current appearance, only that I won't be able to change more?

  Are there risks with regard to the compatibility and stability due to switching of CC to LR6?

  Another question: are there any other restrictions with the Windows program (in order not to count mobile / Cloud / etc) in LR6 compared to the CC (meaning in addition to Dehaze)?

  Thank you and best regards,

  R.

  Hi icarus,.

  Your catalog will remain that is after that proceed to Lightroom 6 and all your changes will be kept however, you will not be able to apply dehaze more edits since that option would be eliminated.

  6 of Lightroom is also compatible and stable as Lightroom CC.

  There is no other limitation with Windows program outside the Dehaze slider and the Mobile version.

  Kind regards

  Claes