What is Hello?

Similar Questions

• What is Hello on a microsoft PC

  What is microsoft bonjuor, he continues to say tha it does not work

  Hello

  Hello is an addon for Safari software Apple browsers... This is not a Microsoft product.

• What is service Hello and why is it causing errors in my event log

  Hello service causes an error message every second in my windows event log.

  Here is their help and support: http://www.apple.com/support/bonjour/

  Here is an explanation of what is Hello: http://en.wikipedia.org/wiki/Bonjour_%28software%29

• How updated peripheral PCI & what's this?

  Original title: PCI DEVICE

  HOW DO I UPDATE FROM PCI DEVICE & WHAT

  Hello

  You can get the answer to what is pci device

  http://www.ehow.com/about_5399638_pci-device.html

  and you can update the site to intel!

  Please mark as useful if it helps!

• Nighthawk D7000 no lan led

  I just got a d7000 and its work very well but it is there any lan port on the d7000 lights when the computer is there a setting you need to change to make it work or what

  Hello Ford501

  Check in control LED-advanced-advanced configuration parameters if possible that you can enable or disable, otherwise something can be a problem with the LEDs

  DarrenM

• Internet slows down for netflix on the xbox, and even with netflix

  I have drivers updated, still cannot race, I should throw out and start over, or what

  Hello

  ·        What are you trying to do on the Internet?

  ·        You try to play? If so, you are trying to play games online? From which site you are trying to read?

  ·        Or when you download a movie through Netflix is your slow internet connection?

  Check the article mentioned below to see why is the slow internet connection.

  Why is my Internet connection so slow?

  http://Windows.Microsoft.com/en-us/Windows7/why-is-my-Internet-connection-so-slow

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• My high interest reading Test failed

  Dell Support PC check says that my targeted reading test has no now what :)

  Hello

  read information from DELL on the DELL forums

  http://en.community.Dell.com/support-forums/disk-drives/f/3534/p/19358268/19798979.aspx

  http://en.community.Dell.com/Dell-groups/new-to-community/f/3511/p/19358086/19795086.aspx

  http://en.community.Dell.com/Dell-groups/new-to-community/f/3511/t/19380940.aspx

  _________________________________________________________________

  and here is the link to Dell's Support forums

  http://en.community.Dell.com/support-forums/default.aspx

• my image of the screen is big how can I make it smaller

  My screen is the major newspaper on what it is because of this, how can I fix this need help I tried everything what

  Hello

  You can still use the ENTER key to OK, do not click OK with the mouse cursor.

  There are a few things you can try:

  Change the resolution of the screen;

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-screen-resolution

  If that fixed it, go to the website of your computer manufacturer > drivers download Section > then key in your computer model number > find your operating system > find two graphics / video or from the Chipset drivers and download and install.

  Then try to change the screen resolution.

  Or do a system restore to before that happened.

  http://bertk.MVPs.org/html/restoresysv.html

  See you soon.

• my monitor keeps jumping around her sparkles

  my old monitor just stop working and I got another dell monitor and now it flickers and jumps around, is something wrong with my hard drive or what

  Hello

  1. What is the model of the monitor?

  It may be a few causes for the flashing screen:

  (a) check that the cables are properly connected to the monitor.
  (b) check the display settings on the computer.
  (c) check the resolution of the screen.
  (d) drivers for display adapter must be updated.

  Flicker can be a problem on CRT monitors. LCD monitors (also called flat screens) do not create flicker.

  Please follow the steps below.

  Method 1:

  Follow the steps mentioned in the links below.

  Flicker of the correct monitor (refresh rate)
  http://Windows.Microsoft.com/en-us/Windows-Vista/correct-monitor-flicker-refresh-rate

  Get the best display on your monitor
  http://Windows.Microsoft.com/en-us/Windows-Vista/getting-the-best-display-on-your-monitor

  Method 2:

  Try to update the drivers for the graphics card in the Device Manager and check.

  Click on the link below.
  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

• Used to synchronize to the clip of sanso

  I can't synchronize my library to my mp3.  I looked at using sync, but I can't find the answer.  Now, what

  Hello

  1. What are you referring to sanso clip?

  2 were you able to sync files to your front mp3?

  3. what type of files you are trying to sync your MP3?

  I suggest to browse the articles provided Microsoft and check if it helps.

  Set up a device to sync in Windows Media Player:

  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-device-to-sync-in-Windows-Media-Player

  What should I do if my device syncs with another Windows Media Player library? :

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-if-my-device-syncs-with-another-Windows-Media-Player-library

  Please reply to us with more information, so that we can help you.

• Message saying application blocked by s parameters... Can't play yahoo pool

  HI: hoping someone can help.   I always play for yahoo pool and yesterday I received the message to update java, I did.  I am running windows 8.  Well I go in a pool hall and looks like it's going to load and this box will appear and say:

  Blocked by security application

  Name: Ygames_Applet

  Location: http://yog5.games.sp2.yahoo.com

  Your security settings have blocked an application not approved to run.

  OK well Java is approved and I never changed anything just updated java as they say now I can't play on their site.   Is there a solution to this?  Seems so simple but I can not understand.   Thank you in advance for help if possible.   What

  Hello

  You will probably have to change some security settings in the Java Control Panel...

  This way to get the Java Control Panel...

  • Press Windows + W logo to open the charm of search to search parameters
    OR
    Drag the mouse pointer to the lower-right corner of the screen, and then click the search icon.
  • In the search box, type Control Panel Java
  • Click the Java icon to open the Java Control Panel.

  

  When Control Panel opens, click the Security tab at the top. Under the tab security make sure that enable Java in the browser content is checked and then change the security level.

  -If you have very high selected then change it up, and then click Ok. Try to open the game again in the browser.

  -If it is at the top can change in the middle and click ok. Try again. Remember it is always recomemnded select high. To be sure, you can add the website link under the list of the sites of Exception ==> Edit Site list

• Install windows 7 on a desktop computer

  My old office was running xp pro on a P4 3 GHz 1 GB RAM BIOS version 775i65G P3.00. WAZ XP agree on that, but wanted to install windows 7 on a USB DVD-ROM and I know it would be a new facility, and the problems are now

  1. he got to were I was going to select the installation of the operating system HARD disk and told me that I can because I have to select a disk controller in the BIOS I tried everything but no avail

  2. after a lot of worries and trials now he's going now to pass the windows logo it just stuck in there

  Please, I've been on these now for a week... I can't install it via a USB-DVD-rom or what

  Hello Isaiah,

  Please contact Microsoft Community.

  The description of the question, I understand that you are having problems when you try to install windows 7 in your old office that was running Windows XP Pro.

  I can understand the inconvenience caused, be assured that we are here to help with your concern.

  1. What is the model of the computer and do ?
  2. Check and let us know if there are scratches on the Windows 7 installation disc.

  Causes of error - BOOTMGR There are a number of possible causes of errors BOOTMGR , including the most common error message "BOOTMGR is missing".

  The most common reasons for BOOTMGR errors include corrupt and evil files configured, hard drive and operating system upgrade issues, corrupted hard disk sectors, an outdated BIOSand damaged or loose hard drive interface cables.

  Another reason, you can see errors BOOTMGR is if your PC is trying to Start from a hard drive or a flash drive that is not properly configured to be launched since. In other words, it tries to boot from a non bootable source. Also, this applies to the media on an optical drive or a floppy drive that you are trying to boot from.

  I suggest you follow the steps below to see if it helps.

  Step 1: 

  Disconnect all external devices. You can reconnect these devices once you have completed the installation.

  Step 2:

  Note: Please check the link below for system requirements of Windows 7,

  http://Windows.Microsoft.com/en-us/Windows7/products/system-requirements

  If your computer meets the Windows 7 system requirements then you can proceed to perform a clean installation and do a clean install, you can check out the link below,

  Installation and reinstallation of Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/installing-and-reinstalling-Windows-7

  Important: Make sure that all your data is backed up before performing the clean install.

  For more information you can check out the link below

  http://Windows.Microsoft.com/en-us/Windows7/help/upgrading-from-Windows-XP-to-Windows-7#T1=tab01

  The above information was hoping to get useful, please return it to us if you need additional assistance.

• Photosmart C4780 wireless Mac connection failure

  I, like some others I've seen messages on, will have exactly the same problem with my HP Photosmart C4780 of wireless connection to my MacBook.  I just bought this printer a couple of days with a new iMac (which I have not yet unpacked, yet).  I decided to see if I could go ahead and get the printer works with my Macbook.  Here is a breakdown of the specs, measures and tests.

  1 MacBook OS X 10.5.8 (Leopard) running.

  2. software is installed.

  3. to set up a wireless connection, the "Device unavailable" error appears in a dialog box.  This is the same error that others have had.  He continues with... "The network configuration has been correctly transferred to the device.  However, to continue the configuration of the device in the network, your Mac must have access to the device... ».

  4. I can load the page HTTP for my router (a Qwest Actiontec M1000) and see the IP address of the printer.

  5. I can successfully ping the the IP address Mac printers.

  6. I cannot correctly load the HTTP page to the printer via the IP address and the view that it is different pages.  I can even change some of the settings, however, apparently never really complete updates.

  7. After talking with HP support for more than 90 minutes (after waiting on hold for nearly 45 minutes, not a joke), we arrived at the conclusion that the modem/router must be the cause of the problem.  So, I was told to contact Qwest to get help.  Furthermore, technical support had me through many of the same steps I've seen on other items (for example, reset the printing system, uninstalling and reinstalling the software, reset my router, etc.).

  8 next, before calling Qwest, I decided to see if I could get the printer runs on Windows.  Under WinXP SP2 on a platform completely separate (but), I was able to install the software correctly and successfully a wireless connection to the printer.  I rebooted the machine Windows several times and disconnected the power to the printer just to make the connection is when it was re-powered and rebooted.  And Yes, everything works perfectly on the Windows machine.  It tells me there is nothing wrong with the router (with a possible exception, which I will speak in a moment).

  9. given that the installation worked in the windows box, I decided to call HP.  This time I isn't that hold it for about 20 min.  I told them what the results were in the Windows world, and we proceeded to work on this issue with the Mac for about an hour.  We have made some of the same things, as for the first phone call, in addition to a few other checks.  It simply seems that software on Mac just cannot see the printer, which means that the HP software will be unable to see it as well.  It's very weird because I can still ping and also set up its Web page (on the Mac and Windows machines).  Now technology seems to think that this is a problem with Mac OS because it certainly works with a different OS with the same router.  I'm leaning toward the same conclusion as well.

  10. now for the question of the possible router I mentioned earlier.  I saw in another post where someone says hello.  Something the Actiontec only modems no routing of packets used by Hello.  I have absolutely no idea what the Hello devil is.  I tried to do a little research on this and am still confused as to what it is and what it does.  However, if Hello is something specific to the Mac and has nothing to do with the router itself, then it seems to me that the router had no knowledge of Hello (and certainly would not care).  Therefore, the ability of routers delivers packages for different platforms should not be affected by this Hello thing.  However, this does not mean the packets are not getting lost once they arrive at the Mac because of Hello (again, not knowing what it is).  Now if that's the case, then it seems to me that the problem would be with the Mac (in conjunction with this thing Hello), not the router.

  11. other positions reported this same problem wireless with this same printer using OS X 10.6 (Snow Leopard).  If this is true, then when I finally unpack my new iMac, I expect to have the same problem... we'll see when I am near to it.  If he did not have this same problem, so maybe there is hope if I upgrade my MacBook to Snow Leopard.

  If anyone has any other light to this problem, please let me know what might be the underlying issue, and how can I fix this (if someone already has).  Thank you.

  Finally, problem solved!  Here is the solution, if someone else is facing a similar problem.

  Since I found the IP address of the printer on the Web page of my router, I went in "Print and Fax" system preferences.  From there, I clicked on the sign "+" to add a printer.  Nothing appears in the default tab.  So, I went to the IP tab.  From there, I selected the Protocol for the "HP Jetdirect - Socket".  In the address field, I entered the IP address of the printer.  After a few moments, the printer was found and the field "Print using" is automatically filled with the print driver.  I clicked on "Add", and low and here's the printer now appears in my list of printers.

  The second representative of HP I was working with me had to go through this same series of steps with one exception.  Never, we put the Protocol field.  He was left as default "Line Printer Daemon - LPD".  When this was done, nothing ever appeared.  So, I think that the trick was to change the field Protocol, as shown here.

  I hope this helps those who have a similar problem.  Good luck.

• Like PEECAM, I have a probook,

  and no improvement to turn off, so I suffer from the same problems. Frustrating or what

  Hello

  Please run the troubleshooter by returning the steps in the http://windows.microsoft.com/en-US/windows7/Open-the-Windows-Media-Player-Settings-troubleshooter link and check with the question.

  Hope this helps!

• People hub crashing

  I ran updates on 9 July. Now, the people Hub will not be open for more than 30 seconds, it looks good, I can drag the screen and then nothing. Only, it closes and returns me to the start screen. Any thoughts?

  Update: it seems that crash when I enter the new section what

  Hello

  This issue could be due to corrupt people application installation files.

  I suggest you run the troubleshooter in Windows 8 App and check if this solves the problem.

  You can download the troubleshooter in Windows 8 App from this link "App Troubleshooter".

  I hope this helps you solve the problem. If the problem persists or if you have other problems with Windows, please post in the Microsoft Community. We would be happy to help you.