What is the problem with the BizTalk configuration tool?

Similar Questions

• What is the best configuration of network with 4 NICs (2 x 10GB and 2 x 1 GB)

  I have 4 hosts running ESXi 4 Enterprise license with 2 x 10GB and NIC 2 x 1 GB, what is the best configuration of network to be used in this configuration? where FT logging should go? I can't add NICs more because it is on the HP blades.

  It's my current setup:

  

  Thank you

  Dan

  You talk about the c3000 blade enclosure, aren't you?

  For a solution tolerant when disaster strikes, you will go probably with:

  VSwitch0 has.)

  Physical NIC: vmnic0 (1 Gbps) + vmnic2 (10 GB/s)

  (A.1) VMkernel Port Group (network management)

  vmnic0 = standby

  vmnic2 = active

  (A.2) VMkernel Port Group (Vmotion)

  vmnic0 = active

  vmnic2 = standby

  Networks of Virtual Machine A.3)

  vmnic0 = standby

  vmnic2 = active

  VSwitch1 B.)

  Physical NIC: vmnic0 (1 Gbps) + vmnic3 (10 GB/s)

  (B.1) VMkernel Port Group (Fault Tolerance)

  vmnic1 = standby

  vmnic3 = active

  -Default - VMware uses round robin to assign a virtual computer to one vmnic.

  So you don't configure port aggregating on the switches.

  You can, however, traffic using if possible VIRTUAL networks, this is why you must configure the ports as junction ports.

  André

• What is the right configuration of the port for my Photosmart C6180 using 32-bit Windows 8?

  Hi all

  I have a HP Photosmart C6180. I recently changed to Windows 8 32-bit. I downloaded the HP Windows 8 drivers, but I still have problems with the printer. In Control Panel, the printer status says "error".  I think that it could possibly be a problem with the printer port settings. So, my question is, what is the right configuration of the port for my Photosmart C6180 using 32-bit Windows 8?

  I would greatly appreciate any help you can give me. Thanks, JoeRocket

  Hello JoeRocket,

  Welcome to the HP Forums!

  I understand that your Photosmart C6180 enjoys a status of "error". I will do my best to help you! I would start by following this entire document on "Printer is off-line" Message appears on the computer and the printer does not print.

  This document provides steps to check the printer driver and port of your computer. Please post your results, I'll be looking forward to hear from you.

  Have a good night!

• Problem with the server configuration tool Web + APSB07-02

  Recently, I applied the updated connector in APSB07-02. Today, I tried to create a connector to my new cluster CF and get the following error when you use the Web server configuration tool:
  
  "The JRun servers on host 127.0.0.1 must be upgraded to use this version of the Web Server Configuration tool"
  
  FC 7.0.2HF1
  JRun 4 Updater 6
  W2K3 SP1
  
  Is date referring too?

  The article for the hotfix has been updated. Step 7 Installing multiserver in the article also says to the jrun-hotfix - 65311.jar and save in {jrun_root} \servers\lib. This can cause problems if there are already fixes in the {jrun_root} \servers\lib. Step 7 will be changed to have the jrun-hotfix - 65311.jar put in another directory, then change the java.class.path in the {jrun_root}\bin\jvm.config file so that the jar file is at the front of the class resembles the following:}

  Java.class.Path={Path-to-jar}/JRun-Hotfix-65311.jar,{application. Home} / Servers/lib...

• What is the best configuration of memory heap for JBoss?

  I'm running a Windows 2003 server and JBoss runs as a service.  Configurations current heap is 1024, but I'm having some problems with the failure of the service.  What is the setting of optimal heap memory?  Thank you

  There is no memory optimal setting for LiveCycle.

  It depends on the components that you have chosen to deploy.  Content Services ES2 is deployed, your chunk size settings memory must be about 2 GB if 1.0 to 1.7 GB may be sufficient.

  http://blogs.Adobe.com/LiveCycle/2010/01/optimal_livecycle_es2_jboss_ru.html

• What is the ideal configuration for a new Mac

  Hi all

  First: the reason for this post

  For awhile, I'm faced with a problem on the Adobe software could not be resolved by all the good people at Adobe.

  The problem is that I can't use CC libraries to its full potential. All I can do is save the shades of colors to a library, but no matter what other assets (chart, type specifications etc.).

  Whenever I try to add an asset in a CC library of in Illustrator, I get an error saying "the file may be read-only or another user can open. Please save the document under a different name or in a different folder. Well, there is no one else and saving to a different location or with a different name does nothing. I got the Adobe employee watching my iMac (remotely) to find out what goes wrong. But despite all good intentions, no one was able to solve this problem. And I left it this way for almost a year. OK, so far, for the reason...

  But today, I created a new user on my iMac with the same admin privileges as account when I first set up my iMac, I created. And guess what? Connect with newly created account and using Illustrator on it to add assets to a CC library works without any problem.

  Why? What is the difference in these accounts, I wondered. And after watching the activity monitor in both accounts, I think I know why, but I do not understand.

  My new account is the user name 'Test', and my old account first (first) when I created my iMac is "Letsgo.

  On the account of 'Test' in the activity monitor all the I see is the user 'Test' for all running processes.

  But 'Letsgo' account I see, of course, a lot of process for "Letsgo" but I also see other users as 'root' or '_spotlight' or '_appleevents '. The way I see it, these additional users are very similar to "default" OSX system accounting.

  Press 'CMD + S' to soon... Sorry... This should be added...

  And now the question:

  It is advisable to set up a Mac with the account of user by default when you first set up the Mac and keep this for purposes of administration and create a new account for day-to-day work? I want to upgrade to El captain in the coming weeks and want to do a clean install, if the implementation of different accounts is the best way.

• What is the highest configuration of X 230 available?

  Hello

  What is the best/most quick configuration / highest X 230? I have trouble finding this information.

  Currently, I have the model i7 - 3520 M 2.9 GHz 16 GB IPS and want another one (X 230), preferably the best available configuration.

  Best regards, Marco

  If by 'highest configuration', you hear the fastest and the best screen, you

• What is the correct configuration of ESX host IP

  I guess you could say Im having a moment of self-doubt.

  Im sure this has been answered, and if you know the link, I would be very grateful if you could point me in the right direction.

  The question is, is it recommended or does have the ESX hosts on a different IP range for the rest of the VM?

  Our SAN has a different ip address range and vmotion has a different ip address range.

  What is the best practice for this?

  Thanks for your help.

  Different logical networks and, if possible, different networks (with VLAN or physical switches).

  If you use VLAN you can use only 2 NICs (instead of 4) for SC and vMotion and difficulty preferred a NIC for each portgroup

• What is the best configuration of battery for lenovo 420 s

  I read on the lenovo Web site, you can get up to 9 hours on the thinkpad 420 s and I was wondering if anyone knew the farm configuration to achieve this setting? Up to now I get only up to 3 hours IF I have it on very low performance. I generally keep a maximum performance when it is plugged. Anyone have any ideas?

  I think that would be carried out using a battery 9 cells more the extra battery that can replace the optical drive in Ultrabay housing. http://shop.lenovo.com/SEUILibrary/controller/e/web/LenovoPortal/en_US/catalog.workflow:item.detail?...

• What is the hardware configuration recommended for 11 G R2 on Windows Server 2008 R2 64 bit

  We are about to move from 10 G to 11 G R2 R2. The platform provider supported for our application is Windows server 2008 R2 64-bit. I have to write a specification document to support my request for new material and I would like some guidance as to the recommended configuration. Environment development database server will have to host dev, test, and preliminary databases for a database of 10 GB. The production server will host only the production database.

  Any guidance appreciated.

  concerning

  Madre

  Hello

  It's all sorted out.

  concerning

  Madre

• What are the best free tools for Oracle DBA development?

  Hi, I have been for years production dba. I am familiar with a complete cycle of the installation of the database, configure, backup recovery, etc.
  
  Now my role will change soon for development dba. I have no problem to create instances. Then in the data modeling, data standardization, etc., what kind of tools I can use?
  
  Good suggestions, or documents that you can provide?
  
  Thanks in advance.

  Oracle SQL Developer Data Modeler and Oracle JDeveloper can be used for data modeling. Both of these tools are free. You can try and make your idea - they are free.
  We will be happy to receive your comments on Data Modeler.

  Philippe

• Problem with siebel Database Configuration - data seed

  Hello
  
  I installed successfully in siebel 8.0 and was able to open the application in thin client.
  
  When installing, I chose ENU both ARA language packs for gateway, server, sweapps.
  
  But DB configuration I did it only for ENU as primary. Then I also migrated the repository of Dev environment to this environment.
  
  Later, I had an obligation to allow also the application of the ARA. So I started again with the DB Config Wizard with step 'Add existing language... '. ", but he had failed with error
  
  Cannot open the file 'set_lov_add_lang.sql '.
  
  The solution to this problem, apply the latest patch on our Oracle DB server as well as on the client. This information I got from Metalink3.
  
  Now my question is if I want to config DB from scratch first, what are the steps must be taken to avoid any kind of referential/unique integrity constraints?
  
  Please suggest.
  
  Concerning
  Vandenplas

  Vandenplas,

  If you rerun the process data of seeds, you will get errors that can be scrapped safely due to data already available in your DBMS seeds.
  Only trade off power, import will take more time because of errors.
  Best regards
  Evtloglvl

• BlackBerry Smartphones do you know what are my problems with my camera and how to solve?

  Mine is Curve 3 G running OS 6. I have 3 years now.

  Never installed any themes. I removed all languages, except for English and mandarin. Obtained third-party applications, which are whatsapp and screen grabber. I also youtube, twitter and yahoo messenger but I think that they are developed by rim. I uninstalled the default games from the early days, owner of the device and never install others. I also removed the maps and the world of blackberry. In any case, they are useless.

  I don't store a lot of pictures and the ones I did on my ram external 2gigs. I have not all media files. Just the default values.

  I join 1 group and it's not active. I don't have multiple conversations. I end conversations as soon as they are finished. BBM contacts grow about 1-2 monthly and phone books from 3 to 5 every week. I am a seller.

  I delete e-mails from the unit as soon as I finished reading the. Never navigation because the browser kills each front page loaded completely, making me unable to use youtube.

  I remember regular cleaning to run hourly.

  I do battery pull everyday because I'm tired of waiting for the clock or the gel to disappear, which could take more than half an hour if I let them which of course eventually crashing.

  Never have data backup because the device freezes the second I connect it to the PC with desktop blackberry on.

  So the question is do you know what are my problems and how to solve? Because I did not.

  Hello

  Well... We must memory cleaner is enabled, this feature is known to cause many problems!

  Try a battery pull reboot and let us know.

• What is the main development tool for designing an Essbase?

  Which are below or other is the main development tool for designing an Essbase?
  1 Essbase Studio Client Console
  2 Essbase Integration Service Console
  3 Essbase Administration Console Service
  
  Essbase Stidio exists only in version 11, EAS can be used to modify a cube for sure, but at the beginning, status to set up a cube, seems we have to use another tool for the design of the Essbase Cube. HIA is the tool for developing the cube from RLDB. But after Essbase Studio appear, seems Essbase Studio is a powerful tool for developing a CUBE, but I can not find the method to create the attriibute dimension and the place to associate dimension attribute of standard dimensions with Essbase Studio Console?
  
  I'm confused, what tool is the most powerful to create a CUBE which include: alias, formula, attribute protected association and UDA years?
  
  Please advise, thank you!

  user2571802 wrote:
  Essbase Studio appears, seems Essbase Studio is a powerful tool for developing a CUBE, but I can't find the method to create attriibute dimension and the place where
  Associate dimension attribute of standard dimensions with Essbase Studio Console?

  Reading of:- Re: Esbase Studio question - how to put in place the protected attribute?

  See you soon

  John
  http://John-Goodwin.blogspot.com/

• Problem with Xcode command-line tool

  Hello

  Last week I upgraded my macbook pro with the latest OS X Capitan and 7.3 of Xcode.

  I also installed the command line for Xcode Tools.

  But there is a problem because the "command-line tools" in Xcode do not work, for example, I am getting following error:

  MyMacBookPro-5: ~ make amitc$ xcrun

  xcodebuild: error: SDK '/Applications/Xcode.app/Contents/Developer/Platforms/MacOSX.platform/Developer /SDKs/MacOSX10.10.sdk' is not found.

  xcrun: error: cannot find the utility 'make', not a tool of development or on the WAY.

  Does anyone know any solution to this problem?

  (I don't understand why he's trying of MacOSX10.10.sdk, while it must search for MacOSX10.11.sdk).

  With our thanks,

  Amit.

  You agree with the terms and conditions of the license?

  sudo xcodebuild-license